Problem with a structure of business

Similar Questions

• problem with tab structure control and event

  Hello

  My program has a tab control. In each tab, I have an event structure to control some events.

  I encountered some problems. These are:

  1. in each tab, I set tab as an event control, to altogether from the structure of the event as tab change (for example, the image below). My first problem is that when I change the tabs, in the arch depending on whether my program is entered in the next tab environment, happening at the event: change value to main tab! And gives bad result.

  

  

  2 - I've scheduled two final tabs as below in the image. I had no routine in these two tabs. Simply, I want when I change the tab, it goes to the next case of the tab control. But when I run the program, it goes to something as busy after one or two changes tab and did not work properly.

  

  Could someone help me please?

  Thanks in advance

  Baran

  Rebecca wrote:

  I want to have 4 tabs, each tab having 3 Boolean control.

  If in each tab all Boolean control wins 1, a Subvi should be run.

  I wrote this code with some time within each tab loop this case hase 3 for each Boolean control. The result is true.

  But I think that if I write it with a structure of the event within each tab instead of 3 cases, the cpu load will be lower.

  Is it not true?

  Make a unique Structure of the event.

  Add events for all controls (buttons, Boolean)

  When the event is triggeredcheck for active tab control and decide what void / vi to run

  It will work fine you

• Problem with Windows Update - Vista Business 32 bit

  I have continuous problems with the update (classified as Important) Microsoft.NET Framework 3.5 Service Pack 1 and .NET framework.

  This update is always offered to me, but it will simply install noty but I could try

  1. Is there an any secret to work this update?
  2. Is there anything I can do Vista ignore this update and npot spend time trying to download and install it - and also for having me to disassemble the time of everyu tick selection I'll update.

  Thank you in advance.

  F F
  

  Hi Fred Furry.

  Thank you for using the Microsoft Vista answers Forum.

  You can try the following steps and check if we are able to install the update.

  1. click on start, run, type cmd and then click OK.

  2. at the command prompt, type the following commands one by one and press ENTER.

  net stop wuauserv
  regsvr32 c:\windows\system32\wuapi.dll/s
  regsvr32 c:\windows\system32\wuaueng.dll/s
  regsvr32 c:\windows\system32\wucltux.dll/s
  regsvr32 c:\windows\system32\wudriver.dll/s
  regsvr32 wups2.dll/s
  regsvr32 c:\windows\system32\wups.dll/s
  regsvr32 c:\windows\system32\wuwebv.dll/s
  net start wuauserv
  output

  Make sure you disable any security software before installing the update.

  If this does not help, follow the article to manually remove and reinstall .NET Framework on your computer

  Use the Windows Installer Cleanup utility to clean up the State of MSI database for all versions of the .NET Framework.

  And then reinstall all the versions of the .net framework by downloading manually Microsoft Web sites in the link below:

  http://support.Microsoft.com/kb/923100

  NOTE: You can download the cleanup utility mentioned in method 2 of the article mentioned above from
  http://CID-6e60f9c3f18900f8.SkyDrive.live.com/self.aspx/dotnet%20Framework/Dotnetfx%7C_cleanup%7C_tool.zip

  Let us know how it works.

  Kind regards

  Yama - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problem with the Structure of the case

  Hello

  I added a new structure of matter in my VI. However, once added, there is an error that I have really no idea how fix it.

  The error message:

  "Business Structure: selector values are not unique.

  "A value of the selector is used by more than one case.  "It can be in the middle of a beach in one of the cases".

  Could someone help me please.

  Thank you.

  Floret

  Please your zip code as an attachment. See your code will make it much easier for us to understand your problem.

  The error relates to the distinction between each image of the structure of your business. You can have two business executives who launch for the same input selector case.

  For example, if I had three managers of cases that have been '0..', '1', 'Default', then frame 1 & 2 times would launch if the entry is 1 (this is not allowed). Check you definitions of statement.

• Problem with Contact form on Business Catalyst - Muse CC

  Hello

  I created a website with Muse CC, then I host them on Adobe Business Catalyst with Subscription Plan Web hosting a 6euros.

  My problem: I can not retrieve mails sent to my contact form...

  But on my admin and wrote that I received the e-mail from three... Can you help me?

  Thank you

  Problem solved!

  Contact form doesn't work with @ Hotmail.com, you must create a @gmail account.

• problem with file structure.

  Hello

  Im trying to import video into Flash. I've converted an flv and use the workflow of flash media with a standard game server option and the stop bar.

  I imported into it and it works find when you select just the individual swf that it loads in. The problem im having is that when I go to it through the home page, all the loading of the page apart from the video.

  Ive tried to move around, movement where all assets for video are ect.

  I know that the file structure is important to this work.

  I have a main folder called interactive / and have a FLA and a SWF file and the swf and fla home page.

  Currently I have the swf video in the file swf with the flv and swf playback and stop.

  Any ideas?

  Thank you

  you change the code in the swf file that is loaded by your main swf.  This should be the same swf that loads the video.

• Problem with nested structures event

  Hello

  I'm rather new to Labview and I wanted to use a structure of nested in one of my programs at the event.

  However, I seem to fail to do things.

  I created a minimal example of construction that I use, you will find in the attachment.

  The idea behind this program is as follows.

  1. I have run the program and go into a while loop

  2. once I have hold down a button on front of a counter is increment every 100 ms.

  3. when I release the incrementing buttun stops.

  However, this does not work. What I am doing wrong?

  Thanks in advance!

  Never stack event structures. Never ever.

  That being said, your code contains a lot of illogical parts, for example a queue time when using a case of 0-timeout event.

  Please use a unique event structure. Where growth is expected to run, set the timeout case e .g. 100 (using the shift register) and once it is based again on set it back to-1. Initialize the shift with-1 register.

  Also avoid using references and nodes property to read/write the values. These are bad practices (in most cases) and bury a lot of run-time performance.

  A second shift register allows to keep the numerical value and increase the value in the case of timeout. Update of the terminal after the structure of the event.

  Norbert

  EDIT: My first line is a rule of thumb. With the increase in the skills of LV and appropriate design, the stacking of the structures of the event is possible, but you must know the rules. If this isn't the case, you won't fail hard.

• Problem with JCA - DB in business

  Hello
  
  I call you to the database with JCA in business, but when the output contains the character ' * & * ' show business ' * & amp *;
  
  For example
  
  OUTPUT OF the comic:_
  
  NT AMERICA & SAN FRANCISCO
  
  RELEASE OF BS_
  
  
  < envelope xmlns = "http://schemas.xmlsoap.org/soap/envelope/" >
  < body >
  < OutputParameters xmlns = "http://xmlns.oracle.com/pcbpel/adapter/db/SGT/PKG_SGT_OPER/PRC_OPER_SRV_DAT_CON/" xmlns: xsi = "http://www.w3.org/2001/XMLSchema-instance" >
  < OUT > AMERICA NT & amp; amp; SAN FRANCISCO < / OUT >
  < / OutputParameters >
  < / body >
  < / envelope >
  
  Published by: user8674403 on 28-ene-2011 10:51
  
  Published by: user8674403 on 28-ene-2011 10:52

  Hello
  In Xml '&' is represented under the name 'and' so its been shown as & make an XML valid.

• problems with publising on catalyst business

  I need help to publish my site on businesscatalyst.  There is no respons Server

  Hello

  Please check the following thread, if it's the same problem

  http://forums.Adobe.com/message/5990480

• Structure of the event: problem with data transfer

  Hello everyone,

  for three days I'm troubleshooting an issue in LabView with the event structures. I really hope someone can help here, because I can't find anything on the entire WEB.

  I had six groups of equal to a VI entry, each containing five checks enum (among others) where the user can specify some configuration of measurement data. I want the program to do is: to recognize if a any of these enum values has been changed and if yes, then submit the values containing the cluster in a subvi then calculates the wiring and affect the material of the ports. In addition, i need to submit the number of the enum element that was changed, so the program is able to clear the user input in the case of a breach (e.g. If the user sets two entries of enum control 1 meter and 2 Group 1 and then tries to set a third counter of entry to port 3, the program displays a message and deletes third entry as the number of entries of counter is limited to 2 per cluster).

  To resolve this problem, I used a structure of the event with 6 x 5 cases (change of enum value 1 Group 1 Group 1 enum value 2 change... and so on until the change in the value enum 5 Group 6).

  

  The problem is that if the user changes a value, the event structure reacts and performs the proper case; However VALUES of the cluster, the user changed are not subject to the SECOND time that an event occurs. It is a kind of a situation, "n-1". For example, if all five controls Enum of Group 1 are 'disabled' first and the user sets enum 3 of 'Meter entry', the structure of the event runs but submits the values previous to the Subvi (all enums 'Disabled'). When the user makes the second change, say that enum SWITCH1 to "Analog Input", the structure of the event is running again and passes the values of the FIRST user to the Subvi editing, then the Subvi gets data "enum 3 meter inlet and all other disabled enumerations.

  In easier words: if I have new values on my cluster "Kanal 1" (left side of the screenshot) and run the structure of the event, on the right side to "Kanal 1" indicator, I get the previous values (n-1).

  The structure of my event is in a while loop. If I create a timeout every 10 ms, and a loop of 250 ms the waiting time, I got the 80% chance that the recent changes are transferred to the Subvi correctly, in other cases I have a delay of the 1 step as described above. It seems to be directly based on the time that I specify the while to wait - but I can't explain it and I cannot accept a less than 100% chance to transfer the correct data, nor can I accept delays of a few seconds for each loop run. If I indicate timeout (infinite) get delayed 1-1 step values in all cases.

  When I specify cases of event to react on "all items value change" of the structure of the event behaves properly - but then I can't handle indicate which element has changed, as the CtlRef of output in case of a structure does not specify "enum 1, enum 2..." but only "Group 1".

  Does anyone have a solution to this? It is certainly a problem with the structure of the event, but I can't understand what to change.

  Thank you much in advance,

  Mr. Boiger

  This is because the terminal is read until the structure of the event runs.   Terminal is read, the event structure is waiting for an event.  The change in value.  Business events are running, but the value is the old value.

  Put the terminal inside the event.

  Or, you can display the connector called "New value" on the side left (stretching down from the border of the node 'CtrRef').  Use a wire one to come.

• Problem with Skype for business

  I downloaded Skype for business and office 2016 on Windows 7.

  I do not see the options "share desktop" or "conference call".

  Kindly help

  Hi Christophe,

  Thanks for posting your query in Microsoft Community.

  Please refer to the procedure below:

  (i) start a conference call

  Make sure that your contacts are available to check their current status first. Then follow the steps below to invite to the conference call.

  1. In the Skype for the main window of business in your contact list, hold down the CTRL key and click on the names of your contacts to select for your meeting.

  2. Right-click on the selection, then click on start a conference call.

  3. Click on a Skype call.

  Your contacts can receive a notification and may accept or reject your application for the conference call.

  Add other people to the conference call

  If you need to add other people to your conference call, you can drag their names in your list of Contacts meeting. Or add them using the menu of people:

  1. In the conversation, in the members pane window, click invite more people.

  2. Choose a person from the list and then click OK. Skype for business calls for you the person and adds them to the meeting.

  (ii) share your screen on Skype for business

  Please refer to the steps to: share your screen in Skype for business

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• Problems with config Small Business switch

  Hi, I know that if I read the documentation I will come for answers, but I'd really like some input from someone with more knowledge than me. I have a problem with Cisco SF300, one of the Small Business switches. I have a single interface on my router and I need to separate my internal networks, I thought that one way would be to use VLANs. On my two internal networks a network has D-Link unmanaged switches, the other has the Cisco SF300 I did as follows.

  On the Cisco Switch, all of the default ports for ports of junction. I changed FE1-FE24 and GE1-2 to access ports.

  Created two VLAN and placed FE1-FE24 in VLAN10 (also my management VLAN), GE3 is a trunk Port for unidentified VLAN20, VLAN 20 uplinks to my DiLink switches. This way my unmanaged switches traffic arrives on a trunk on VLAN20 untagged port.

  GE4 is a trunk port and I assigned to VLAN1 untagged, tag VLAN10 VLAN20 tag and. 10 of VLANS and VLAN 20 then to my router.

  The plan was to connect GE4 to my router, but I had two things happen that I can't explain.

  All first as soon as I connected my D-Link to GE3 LAN on VLAN20 came down, I couldn't ping servers from computers etc, all devices are connected to the D-links unmanaged. Secondly, the responsibilities of VLAN changed on GE3 GE4, VLAN 10 and 20 disappeared and only the VLAN by default was assigned, also under settings VLAN my state of interface VLAN for VLAN20 shows people with reduced mobility. One of my FE12 continues also to change VLAN access ports.

  Can anyone offer any suggestions as to what might have crushed the LAN and why change my VLAN. I wrote my config running at startup configuration incidentally.

  I added two screenshots.

  Seriously, I'd appreciate the help.

  Thank you

  Bob

  Hi Bob,

  Could you please post a topology? I can help with this, but it would be much easier that I could see your network.

  Thanks in advance,

  Garrett

• Problems with the navigation links in EDIT mode in the Business Catalyst Muse sites.

  Has anyone else had problems with the navigation links / EDIT mode in sites Business Catalyst Muse?

  In EDIT mode, I can't use the list drop DOWN the SELECT DIRECTLY to go to another page or a link. The drafting of the text or label works, but to actually go to a /visit link a hard link is broken.

  

  Others have this problem as well.

  No work around?

  Thank you!

  I have the same problem! Contact BusinessCatalyst today taught me that it is a known bug and have Adobe Muse to fix! LiveChat ticket No. #159685

  When I launched the Web site in may 2015 everything worked well, but since the update of CC, this problem occurred.

  The tip of solution, I received the BC is to always use the navigation menu bar. This does not work for me because my client wants a menu of polaroid...

• Problems with Windows Vista and Quicken 2010 home and business

  While restoring a quicken 2010 file backup of the Windows XP computer to the Windows Vista-based computer, the categories are not loaded

  Hello

  As you are facing problems with Quicken 2010, I suggest you check the link for support:

  http://Quicken.Intuit.com/support/Windows.jsp

• major error with the structure of the event

  IM under LABVIEW 13.0 PRO

  I don't know when this strarted bug happening, but now when I add a business to a structure of the event. Freezes in LabVIEW. I have to close labview with the Task Manager.

  It doesn't matter what code I'm working with, even a new VI, with nothing else than a structure of the event.

  I tried this on my desktop PC, my laptop and my CPU DAQ.

  The error occurs on my desktop and my laptop. But it does not occur on my CPU DAQ.

  Whenever I click on add event usually case, you get a popup to configure and add cases, but with the popup error never comes to the top and labview crashes.

  Theres no code to share the problem ocured when adding events to the event structure. It happened with any structure of the event, in any code, all the time.

  I spoke to an engineer of apllication of labview and suggested to delete the labview.ini file located in the installation of labview directory. I did this and the problem was solved.

  Still not sure what caused this to happen.