Problem with drive temperature and recovery book

Similar Questions

• Problem with drive HARD and Vista install

  Hi all

  A few weeks ago, my Dell Inspiron laptop computer started to freeze. I could boot ok and my desktop wallpaper and icons were all there, but I couldn't run or open anything. I did the Bios tests and my Vista installation disc and told me there was a problem with my hard drive. I wiped it and tried to reinstall vista and that I could see it wasn't working because it took hours and then seems to have stopped again during installation. So I bought a new one and tried to install Vista. everything was going well until it is restarts a second time and I got a black screen with a mouse pointer icon. I had to reinstall it running for about 4 hours, at least an hour of that time which was all that was going on and the hard disk wasn't spinning.

  How long on avg would take to install Vista, if it is running normally?

  is there anything else that might be a problem that would not appear in the repair of Vista or Bios diagnostics?

  Any advice would help a lot.

  If the new hard drive does not work, then the problem is on the motherboard. Your description of symptoms indicates a power supply or motherboard failure. Contact Dell technical support for repair or replacement. MS - MVP - Elephant Boy computers - don't panic!

• [HELP] Problem with the restoration and recovery in the new host

  Hi, guys!
  
  I have tried for two days, but still can't make it work.
  I took a hot (online) full backup archive as well as the control file logs with the SPFILE and then copy the backup to the new host with the same directory structure and parameters. Finally, I tried to restore and recover the database on the new host, but failed during the restore process.
  
  The original host and the new host have the same subject Oracle installed until the patch level. I couldn't understand the solution to this problem based on my knowledge on Oracle DB.
  
  Could someone help me out here? Any advice would be appreciated!
  
  -----
  RMAN > restore the database up to the wire of the sequence 10 1;
  
  From restoration to November 8, 11
  using channel ORA_DISK_1
  
  channel ORA_DISK_1: from datafile backupset restoration
  channel ORA_DISK_1: specifying datafile (s) to restore from backup set
  restoring datafile 00001 to D:\DBDATA\PRODDB\SYSTEM01. DBF
  restoring datafile 00002 to D:\DBDATA\PRODDB\UNDOTBS01. DBF
  restoring datafile 00003 to D:\DBDATA\PRODDB\SYSAUX01. DBF
  restoring datafile 00004 to D:\DBDATA\PRODDB\USERS01. DBF
  restoring datafile 00005 to D:\ORA_DATADATA01. DBF
  restoring datafile 00006 to D:\ORA_DATA\DATA02. DBF
  restoring datafile 00007 to D:\ORA_DATA\INDX01. DBF
  restoring datafile 00008 to D:\ORA_DATA\INDX02. DBF
  channel ORA_DISK_1: backup C:\ORACLE\PRODUCT\10.2.0\FLASH_REC piece reading
  OVERY_AREA\PRODDB\BACKUPSET\2011_11_07\O1_MF_NNNDF_TAG20111107T175037_7CH6YYVJ_. BK
  P
  
  switch to the previous backup
  
  RMAN-00571: ===========================================================
  RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.
  RMAN-00571: ===========================================================
  RMAN-03002: failure of the restore command at 11/08/2011 11:41:33
  RMAN-06026: some targets not found - abandonment of restoration
  RMAN-06023: no backup or copy of the file 4 found to restore
  RMAN-06023: no backup or copy of datafile 3 found to restore
  RMAN-06023: no backup or copy of datafile 2 found to restore
  RMAN-06023: no backup or copy of datafile 1 found to restore
  -----
  
  Here is some additional information you might want to know about:
  
  -----
  RMAN > list incarnation;
  
  
  List of Incarnations of the database
  DB key Inc key STATE ID DB name DB reset reset time SNA
  ------- ------- -------- ---------------- --- ---------- ----------
  1 1 PRODDB 3774691295 PARENT 1 17 APRIL 07
  2 2 3774691295 PRODDB PARENT 521803 6 OCTOBER 11
  3 3 3774691295 PRODDB PARENT 1595143 20 OCTOBER 11
  4 4 3774691295 PRODDB PARENT 1600974 20 OCTOBER 11
  5 5 3774691295 PRODDB PARENT 1952053 27 OCTOBER 11
  6 6 PRODDB 3774691295 CURRENT 2146951 7 NOVEMBER 11
  
  RMAN > backup recoverable list;
  
  
  List of backup sets
  ===================
  
  Time of accomplishment BS key Type LV size device Type elapsed time
  ------- ---- -- ---------- ----------- ------------ ---------------
  37 full 822,34 M DISK 00:29:47 7 November 11
  BP key: 37 status: AVAILABLE Tablet: NO Tag: TAG20111107T175037
  Part name: C:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\PRODDB\BACKUPSET\
  2011_11_07\O1_MF_NNNDF_TAG20111107T175037_7CH6YYVJ_. BKP
  List of files to backup data value 37
  Name of file LV Type cash SNA cash time
  ---- -- ---- ---------- --------- ----
  2149673 full 1 7 November 11 D:\DBDATA\PRODDB\SYSTEM01. DBF
  2 full 2149673 D:\DBDATA\PRODDB\UNDOTBS01 7 November 11. DBF
  3 full 2149673 D:\DBDATA\PRODDB\SYSAUX01 7 November 11. DBF
  4 integer 2149673 D:\DBDATA\PRODDB\USERS01 7 November 11. DBF
  5 integer 2149673 D:\ORA_DATA\DATA01 7 November 11. DBF
  full 2149673 D:\ORA_DATA\DATA02 6 7 November 11. DBF
  7 full 2149673 D:\ORA_DATA\INDX01 7 November 11. DBF
  8 whole 2149673 D:\ORA_DATA\INDX02 7 November 11. DBF
  
  Time of accomplishment BS key Type LV size device Type elapsed time
  ------- ---- -- ---------- ----------- ------------ ---------------
  38 full 6.95 M DISK 00:00:03 7 November 11
  BP key: 38 status: AVAILABLE Tablet: NO Tag: TAG20111107T182034
  Part name: C:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\PRODDB\AUTOBACKUP
  \2011_11_07\O1_MF_S_766606834_7CH8Q439_. BKP
  Control file included: cash SNA: 2151141 cash time: 7 November 11
  SPFILE included: Modification Date: 7 November 11
  
  Time of accomplishment time BS key size Device Type
  ------- ---------- ----------- ------------ ---------------
  18,46 39 M DISK 00:00:05 8 NOVEMBER 11
  BP key: 39 status: AVAILABLE Tablet: NO Tag: TAG20111108T093359
  Part name: C:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\PRODDB\BACKUPSET\
  2011_11_08\O1_MF_ANNNN_TAG20111108T093359_7CJY7TG1_. BKP
  
  List of newspapers archived on backup value 39
  The next time that THRD Seq YVERT low low time next YVERT
  ---- ------- ---------- --------- ---------- ---------
  1 1 2146951 7 NOVEMBER 11 2149493 NOVEMBER 7, 11
  1 2 2149493 7 NOVEMBER 11 2149519 NOVEMBER 7, 11
  1 3 2149519 7 NOVEMBER 11 2149565 NOVEMBER 7, 11
  1 4 2149565 7 NOVEMBER 11 2149641 NOVEMBER 7, 11
  1 5 2149641 7 NOVEMBER 11 2172859 NOVEMBER 7, 11
  1 6 2172859 7 NOVEMBER 11 2197851 NOVEMBER 7, 11
  1 7 2197851 7 NOVEMBER 11 2220349 NOVEMBER 8, 11
  1 8 2220349 8 NOVEMBER 11 2222621 NOVEMBER 8, 11
  1 9 2222621 8 NOVEMBER 11 2222729 NOVEMBER 8, 11
  1-10 2222729 8 NOVEMBER 11 2223088 NOVEMBER 8, 11
  
  Time of accomplishment BS key Type LV size device Type elapsed time
  ------- ---- -- ---------- ----------- ------------ ---------------
  40 full 6.95 M DISK 00:00:00 November 8, 11
  BP key: 40 status: AVAILABLE Tablet: NO Tag: TAG20111108T093411
  Part name: C:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\PRODDB\AUTOBACKUP
  \2011_11_08\O1_MF_S_766661651_7CJY84LK_. BKP
  Control file included: cash SNA: 2223097 cash time: November 8, 11
  SPFILE included: Modification Date: 8 November 11
  -----
  
  Thanks in advance!
  
  Jay

  In short, the RCS of the controlfile will be generally higher than corresponding SCN of the data in the event of hot backup (online) file; However, the two SNA will be the same in the case of cold (off-line) backup. Am I entitled?

  Yes, it's true. In a backup cold (assuming that the CLOSURE was not a SURRENDER but was NORMAL, TRANSACTIONAL, or IMMEDIATE) all files in the database (data files, redo log and controlfiles files) are 'compatible' - at the same point in time, to the same SCN. In a hot backup, the files are updated. RMAN is not necessarily take all the data files at the same time - for example when you have several data files, RMAN would backup the files in batches of 4 or 8 - data files are therefore controlled at different points in time. Similarly, the controlfile is saved last.

  Hemant K Collette

• Satellite A500 - problems with the temperature of the GPU

  The thing is playing Age of Empires online I started having problems with the temperature of the GPU. When you run the AIDA64 the CPU stress test can hold up well, but after 35 minutes the test what AIDA suspended while the GPU fan can't seem to download their revolutions, (I guess that if there was that a rise in temperature would increase the speed of rotation of the fan, don't).

  I consulted the manufacturer of the GPU, nVidia, (the graphic is nVidia GeForce GT 230 M) and tell me to contact Toshiba for other options, since, according to them, the problem is not the GPU.

  Any ideas or suggestions?

  You use your laptop to factory settings?
  Have you installed something that may be responsible for this (non-Toshiba display driver)?

• "HP pavilion slimline: problem with the disc of"recovery"would be"

  I just got a Seagate 1 TB drive backup and have backed up my entire computer to him.  My concern is that my "D" drive, the separate part of my computer that contains the disc "recovery", is almost completely full - its presentation as a solid red bar on my screen - only left 320Mo of 11.7 GB - would have this effect, the performance of my computer at all?  Why is it so plenty of anyway and what can do about it?  Problems with my email and its indicating that I am "" out of memory "-well, I've got a lot of memory on my C drive, which is not a problem, but the same effect my email D drive?"  I use Windows LIVE mail incidentally, and I had problems in the past with it, been quite some time however.  Woud grateful for the help with this.  He used to ask me to put in CD on backup drive D with - don't know why, but I immediately my Seagate drive, now, just do not know what I have to do at this point.  Thanks for any help.

  I have no idea why the "D" drive is a solid red bar, nor why it is so full.  I've changed nothing since I bought the computer.  How would I know if something is to use the D drive?  I thought that it was 'partitioned' off so that he couldn't be touched?  I have everything on my laptop hard drive Seagate, and I mean everything.  I also have system recovery disks of mirror image right after I bought the computer, but that does not tell me why that drive D is now completely "full", it should not be.

  I don't know if you have "solved" the problem, but I guess that the D drive is of no consequence right now even if its 'full' and probably shouldn't be.  Maybe my problem is WINDOWS LIVE MAIL, and I maybe need to do another post to see if anyone can help with the next.  Thank you.

• HP 15 laptop: problem with the touchpad and the key "stuck."

  Hello!
   
  Last weekend, I have an irritating problem with my HP 15 laptop. Bought two years ago and upgrades to Windows 10 a year ago.
   
  First of all, my touchpad started to not work properly. It "freezes" and I can't use it until I click the ESC key, but it doesn't last and "freezes" again a few seconds later. Then, everytime I open a window where there is a text box (Start menu, edge browser, Control Panel, etc.), the number 5 is entered automatically and permanently, as if the button 5 has been blocked. I did a quick check and button 5 do not seem physically stuck.
   
  Yesterday, I restored the system to the factory settings, so I'm back to 8.1 for Windows and then upgraded to Windows 10. Everything seems to work fine, but this morning, the problem was back. Is there something I can do? What is the problem caused by Windows 10 or the computer? Should I restore it to Windows 8.1? Everything worked great til last weekend, I don't know what that was.
   
  Thank you in advance for your help!

  Welcome to the HP support community @gouch3.

  I understand that you have a problem with the keyboard and the touchpad on your laptop from HP 15.

  Have you tried to use a keyboard external and mouse at all?

  Have you tried to go to Safe Mode to see if the problems persist in there?

  Have you tried to perform a material or forced reset Reset?

  Did you do a test of material?

  Have you updated your drivers?

  gouch3 wrote:

  ... Is there something I can do? What is the problem caused by Windows 10 or the computer? Should I restore it to Windows 8.1? Everything worked great til last weekend, I don't know what that was.

  It could be a driver problem to be able to look at that for you, I need your model number. I wish I could give you an answer or not, but at this point without the troubleshooting results and the model number, it is difficult for me to say.

  I can say that if everything works in point 8.1 of Windows without problem, the driver TROUBLESHOOTING is a great place to start. Please try to follow these steps for the keyboard and the touchpad of troubleshooting:

  • Beginning
  • Search for Device Manager
  • Search results, open Device Manager.
  • Click on display
  • Show hidden devices.
  • Click the arrow next to keyboards.
  • Right click on the name of the keyboard device.
  • Select uninstall.
  • Continue deleting the names of devices in the category keyboards until the feature of all the names have been uninstalled.
  • Restart the laptop twice.

  Touchpad:

  • Type of research, "Device Manager."
  • Click on Device Manager,
  • Expand mice and other pointing devices.
  • Right click on the TouchPad,
  • Click on uninstall.
  • Restart the computer laptop twice,
  • Reinstall the TouchPad card.

  I found a document of troubleshooting for you to try also called Portable keyboard troubleshooting. Please be sure to follow the steps described in this document.

  The best document I have for TouchPad problems is the use and troubleshooting of the TouchPad and ClickPad document. 

  Here is a link to the HP Support Assistant, if you need it. Just download and run the application and it will help with the software and drivers that need to put up-to-date.

  This is a great question other clients may also be questioned. When we came to a resolution, please share what has worked for you with others by marking this post as an acceptable Solution. If you want to show appreciation for my efforts today, please take a second to click the Thumbs Up button below.

  If you need assistance, I would be more than happy to continue to help you. Please re-post with the results of the resolution of the problems. Could you please also provide your model number (How can I find my model number or product number?)

  Thank you!

• Problems with Windows Update and load XP SP3

  I had a problem with my system and had to replace my HARD drive and reload XP and all my applications and data.  Now, I installed SP2 and try to install SP3. Windows Update does not work (get the 080244019 error code x) and when I try to install the SP3 files from the Microsoft site, it'll run about halfway through and then stop and hang, displaying the message "Finish Installation" with bar at halfway of the progression.  I tried the MSRT and FixIt nothing helps.  I checked services.msc to see all the required services are enabled or started.  I read that some malware will be stop some services without notice.

  After a few attempts to load the file SP3 failed, check Add/Remove programs in Control Panel Windows XP Service Pack lists 3 but no file size or to update the date information as with other programs.  My browser is IE8 and I was doing some Hot fix for Windows XP downloads, this adventure started about 3 weeks ago, but no other automatic update downloads.  I use the following McAfee provided by my ISP for protection AV and firewall with regular full scans.  Scan today revealed there is apparently a single trojan file that cannot be deleted, but there were no further details.  My system is also fully functional; I seem to get the updates for McAfee and other applications OK but not SP3.  I received or otherwise installed following updates or Hot Fix for XP downloads in the past 3 weeks:

  KB954550-v5

  KB932823-v3

  KB915800 v4

  KB884020

  KB926239

  KB2618444 (Windows IE8 security update)

  I found an answer on another forum on editing the registry for the "/ Edit EDWARD CSDVersion value ' but have not yet tried waiting for any response to this request.  I'd like some useful suggestions.  Thank you and happy new year!

  Thanks for the quick response.  I did some checking on my system, I have XP Home Edition ships with the system bought in July 2007.  Add/Remove Programs shows that the aborted install XP SP3 and IE8 installation; I tried to load the SP2 file but it doesn't show here as an addition, so it may have been part of the original XP CD and I just crush.  Even for IE7 so I am not able to drop back to all recommend you.  I will try your solution later today and post my results. I saved SP2, SP3 and IE8 in my office and a flash player to reload later according to your instructions.  Stay tuned.

  It would be unusual for a CD of Windows XP (official) to have integrated Internet Explorer 7.

• After the last updates of windows have problems with start up and now drivers

  Hello

  After the last updates of windows have problems with start up and now drivers. I get an error code 21 when I try to install the drivers AMD apparently missing.

  May 14, last night I had several (automatically) downloaded windows update

  Today, I was unable to boot my computer with Windows - tried the disk check, start checks etc, and eventually had to use System Restore (for help before the critical update to restore).

  Perfection, everything works, but knowing that windows will attempt to redo an automatic update, tried to check online - no one seemed to have a problem and (naivly) thinking I could always do another restore of the system, I rebooted again.

  Same thing worse. Could not do a sys restore either just before restarting or last night. Chose a date earlier (last week) but then lost the USB drivers and pilots display. Downloaded updated but refuses to let my AMD driver install Windows I have a very unpleasant screen... and I must now stop the installation of this update "critical."

  Would appreciate advice how do my installed display driver or whether anyone else has problems following this update

  Thank you

  Hi Jane,

  You have a disk to install Windows 7 with you?

  I suggest you to check the event viewer for error details report.

  Open event viewer.

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer

• Anyone having problems with Windows 7 and the HP LaserJet P2035n?

  It seems, after a few months of service, there are several problems with this printer and Windows 7 only.  We have several offices that use this printer and almost each one has similar problems.  It will printer randomly disappear, not being able to print anything at random times of the day, to the spooler crashing every two minutes or more.  There is no problem at all with Windows XP or Vista, only 7.  Reinsalling the printer driver takes care of the problem for a few days, but the questions up all over again.

  Hello

  The Microsoft Answers community focuses on issues and problems related to the consumer environment. Please join the Technet forums below:

  TechNet forums

• Hello I have problem with my site, and mozilla. Google chrome, safari, explorer, opera work ok. Mozilla Heve problem with images?

  Hello I have problem with my site, and mozilla. Google chrome, safari, explorer, opera work ok. I have Sobipro for both the company and the logos and images without work!
  When I try to open the url is this:http://www.athens-dayandnight.gr/images/sobipro/entries/288/587_img.jpg

  whith mozilla is the following: /images/sobipro/entries\288\587_img.jpg when ichange it------with this / work.

  any idea?

  Thank you

  Hello, the URLS that contain-in their path are not valid. Firefox is less tolerant to errors in this respect than other browsers.
  Correct the path to http://www.athens-dayandnight.gr/images/sobipro/entries/288/587_img.jpg in the source code of this site or if you don't control the contact of the site their webadmin to do...

• Satellite Pro C650D - problems with the audio and game controllers

  Hello

  I recently had problems with my microphone and speakers/headphones and game controllers.
  Sometimes the microphone stops working when on Skype, for example, but most of the time works fine, once again, when I restart the pc.

  Stakeholders sometimes still work when I connect headset.
  Some of the sounds are still coming through the speakers while some coming through the headphones.

  I have a usb game controller which also did not work everything properly.
  If I assign buttons in the program that they do not work in the game.

  All these devices are in Device Manager in a group that makes me think it's sort of annoying update doubtful that messes with them.

  Any body have similar problems or know what to do better?

  See you soon
  Laurin

  Hello

  Can you please send some details on the laptop model and the system you are using?

  With regard to the issue of sound/mic:
  > The microphone sometimes stops working when on Skype, for example, but most of the time works fine, once again, when I restart the pc.

  Are you talking about internal microphone or external? This only happens using Skype?
  In your case I would test the microphone using different applications to make sure that is not a Skype related issue.

  > Yet sometimes the speakers work when I connect headset.
  I recommend this thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=65295

  The user has had a similar problem, but this phenomenon was linked to the Realtek HD Audio Manager settings.
  She wrote:
  + In the upper right corner, there is a small yellow folder called "Connector settings" in my version. +
  + There, finally I could re-enable the setting "enable popup dialog box, when the unit is plugged. +

  + So now when I plug an external speaker or headphones, it appears, and I select the option "helmet" (instead of "line-in"), and then the sound only through the headphones/ext.speaker.+

  Regarding the game controller:
  > I have a usb game controller which also did not work everything properly.
  > If I attribute buttons in the program, they do not work in the game.
  I put t think its problem of laptop in my opinion, you must make sure that the controller is compatible with the games you play and also recommended to check some info provided by the manufacturer of the game controller.

• How can I return to 6.3 4.0 I have never had a problem with 3.6 and now 4.0 crashes all the time tell me how to go back

  How can I return to 4.0 3.6 I've never had a problem with 3.6 and now 4.0 crashes all the time tell me how to go back

  Downgrade to Firefox 3.6 first of all uninstall Firefox 4, but do not select the option 'remove my Firefox personal data '. If you select this option, it will delete your bookmarks, passwords and other user data.

  Then you can install the latest version of Firefox 3.6 available to http://www.mozilla.com/en-US/firefox/all-older.html - it will automatically use your favorite courses, passwords etc.

  I recommend, to avoid possible problems with decommissioning, accessing your profile folder and delete the following files if they exist - extensions.cache, extensions.rdf, extensions.ini, extensions.sqlite and localstore.rdf. Delete these files will force Firefox to rebuild the list of installed extensions, check their compatibility and cancel the toolbar customizations.

  For more information on how to find your profile folder, see https://support.mozilla.com/kb/Profiles

• Problems with wifi, bluetooth and gps in my iphone after updating iOS 6

  After that the last iOS 9.3 update my iphone 6 has problems with wifi, bluetooth and gps. Now, my wifi connection is slower and falls easily on a short distance. My bluetooth does the same. But the biggest problem is the GPS on my phone. I tried Island:

  -By doing a reset network

  -Do a reset total and restore my phone

  -To restart my phone twice.

  -Audit and third-party applications unnistalling

  Nothing works. I was in the apple store where they checked my phone and they say everything is ok with the phone. I'm not crazy, and I know when something does not work correctly. Also, I think it's iOS 9.3 update a reaponsible for my phone issues.

  Please fix bugs fast.

  Having the same exact problems since the upgrade. In addition, battery drains very quickly now, and sometimes the phone becomes very hot. It took to the Genius Bar and they told me everything was normal in the diagnostic tests. Restored, restarting, etc., and always the same problems. GPS locates me, but then don't follow my movement at all and told to go outside as the gps is not detected even if I am outside. Bluetooth connection to the car and watch grave intermittently. Signal WiFi is greatly reduced and falls easily.

• Problem with the report and the system of axis 2d

  Hi, I'm trying to write a script with tiara, who wrote a 2d axis system in the report but I'm having a lot of problems with it.

  What I'm trying to do, is make 3 or more system axis 2d in the report, each displaying a part of the data of 2 channels (x = ch0, ch1 = y).

  With only 1 graphic I get what I want, but when I try to add the 2nd or the 3rd, they show without my defined x-scale and with the offset x different from the first chart.

  I tried everything, but I could not remedy

  I added as attachments the .csv file that I use to ch0 and ch1 and 2 screen shoots "what I get" (about the problem with the script) and "what I hope to get" (done manually, is what I'm trying to get the report)

  Any help will be appreciated, thanks in advance

  Ierman

  I'll post my code here:

  Dim Xscale, Yscale
  XScale = Array (0,25,0,5,49)
  Yscale = Array(-0.2,0.2,-0.2,10,4)
   
  Call PicDelete()
  Call GraphObjNew ("2D-Axis", "2DAxis1")
  Call GRAPHObjOpen ("2DAxis1")
  D2AxisTop = 1

  D2AxisBottom = 70
  D2AxisLeft = 1
  D2AxisRight = 1
  Call GRAPHObjOpen ("2DYAxis1_1")
  D2AxisyScaleType = "manual".
  D2AXISYBEGIN = Yscale (0)
  D2AXISYEND = Yscale (1)
  D2AXISYORIGIN = Yscale (2)
  D2AXISYTICK = Yscale (3)
  D2AXISYMINITICK = Yscale (4)
  Call GRAPHObjClose ("2DYAxis1_1")
  Call GRAPHObjOpen ("2DXAxis1_1")
  D2AxisxScaleType = "manual".
  D2AXISXBEGIN = Xscale (0)
  D2AXISXEND = Xscale (1)
  D2AXISXORIGIN = Xscale (2)
  D2AXISXTICK = Xscale (3)
  D2AXISXMINITICK = Xscale (4)
  D2AxisXTxt = ""

  D2AxisXColor = 'black '.

  D2AxisXTickAuto = 1
  D2MTickLineWidth (1) = 0.1
  D2MTickLineType (1) = "solid".
  D2AxisXTickSize = 60
  D2AxisXTxtAutoCo = 0
  D2MTickColor = "red".
  Call GRAPHObjClose ("2DXAxis1_1")
  Call GraphObjNew("2D-Curve","New_Curve")

  Call GraphObjOpen ("New_Curve")

  D2CCHNX = "[1] / [1]" "

  D2CCHNY = "[1] / [2]" "

  D2CurveColor = "red".
  Call GraphObjClose ("New_Curve")
  Call GRAPHObjClose ("2DAxis1")

  Dim Xscale1, Yscale1
  Xscale1 = Array (25,50,0,5,49)
  Yscale1 = Array(-0.2,0.2,-0.2,10,4)
  Call GraphObjNew ("2D-Axis", "grafic")
  Call GRAPHObjOpen ("grafic")
  D2AxisTop = 40

  D2AxisBottom = 37
  D2AxisLeft = 1
  D2AxisRight = 1
  Call GRAPHObjOpen ("2DYAxis1_2")
  D2AxisyScaleType = "manual".
  D2AXISYBEGIN = Yscale1 (0)
  D2AXISYEND = Yscale1 (1)
  D2AXISYORIGIN = Yscale1 (2)
  D2AXISYTICK = Yscale1 (3)
  D2AXISYMINITICK = Yscale1 (4)
  D2AxisYTxt = "" ' testo asse label y
  Call GRAPHObjClose ("2DYAxis1_2")
  Call GRAPHObjOpen ("2DXAxis1_2")
  D2AxisxScaleType = "manual".
  D2AXISXBEGIN = Xscale1 (0)
  D2AXISXEND = Xscale1 (1)
  D2AXISXORIGIN = Xscale1 (2)
  D2AXISXTICK = Xscale1 (3)
  D2AXISXMINITICK = Xscale1 (4)
  D2AxisXTxt = «»

  D2AxisXColor = 'black '.

  D2AxisXTickAuto = 1
  D2MTickLineWidth (1) = 0.1
  D2MTickLineType (1) = "solid".
  D2AxisXTickSize = 60
  D2AxisXTxtAutoCo = 0
  D2MTickColor = "red".
  Call GRAPHObjClose ("2DXAxis1_2")
  Call GraphObjNew("2D-Curve","New_Curve1")

  Call GraphObjOpen ("New_Curve1")

  D2CCHNX = "[1] / [1]" "

  D2CCHNY = "[1] / [2]" "

  D2CurveColor = "red".
  Call GraphObjClose ("New_Curve1")
  Call GRAPHObjClose ("grafic")

  Hi lerman,.

  Here is an edited version of your code that works on my computer.  A problem that I know that I fixed it was that your presentation of the STATE was in the name-oriented mode but you use the variables based on the number to assign it X and Y channels.  The execution of these commands in a loop FOR makes it much easier to debug the code and to avoid any annoyance at first.

  Brad Turpin
  Tiara Product Support Engineer

  National Instruments

• Problems with the date and time - have to reset the date & time on reboot

  original title: problems with the date and time

  Whenever I turn on my computer (Windows XP 2002) I click on F2.  Then I re - set the date and time it occurred in January 2006 1 h every time I have turn off the computer.  Can someone tell me what I need to do?

  You need to replace the battery in time clock (RTC) real of your computer.  It can also be called the CMOS or BIOS battery.

  Many computers, this battery is an inexpensive CR2032 button available in almost every pharmacy corner.  There are, however, some computers (especially laptops) that require a different (and probably more expensive) battery.

  Whatever the expense, almost all of these batteries are easy to replace.

  To get help, post back with the brand and model of your computer.