Problem with laptop goes into hibernation in Vista mode

Similar Questions

• Blue screen when the system goes into hibernation with BCCode: 9f

  Every time when my laptop back into hibernation mode, it gives me option to start in safe mode or start windows normally. When the computer starts, it gives the error message. :

  Signature of the problem:

  Problem event name: BlueScreen

  OS version: 6.1.7601.2.1.0.256.48

  Locale ID: 1033

  More information about the problem:

  BCCode: 9f

  BCP1: 0000000000000003

  BCP2: FFFFFA800B39F050

  BCP3: FFFFF80000B9C3D8

  BCP4: FFFFFA800F83AAB0

  OS version: 6_1_7601

  Service Pack: 1_0

  Product: 256_1

  Files helping to describe the problem:

  C:\Windows\Minidump\082313-10998-01.dmp

  C:\Users\ilyasm\AppData\Local\Temp\WER-108108-0.SysData.XML

  Based on a similar thread, I tried to apply the KB975599 patch, but get the following message if poster "this update is not applicable to your system".

  I downloaded the minidump in skydrive at the following link.

  https://SkyDrive.live.com/#CID=F6050197253DE2F2&ID=F6050197253DE2F2%21119

  I use a Lenovo T420s laptop.

  IM

  All of these related usbehci.sys Microsoft USB 2.0 Enhanced Host controller driver Miniport takes too long to respond.

  What USB devices have connected you?

  Here are some suggestions for fixing USB
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

• I restored my laptop Toshiba because I had some problems with it and now my Windows Vista computer is indicating that it is 'invaild.

  RESTORED FOR LAPTOP, WINDOWS VISTA INVAILD

  Hi I'm new to these fornums

  I restored my laptop Toshiba because I had some problems with it and now my Windows Vista computer is indicating that it is 'invaild...

  I have the product key on a sticker on the bottom of the laptop, but whenever I entered the code, I also get this:

  The product key you entered will not work with this edition of Vista

  I know that most people are trying to say to activate by phone, but this option is not available

  Help, please

  Now that you have found the key and the certificate of authenticity, you must change to the key on the COA sticker - ONLY then it will activate.

• When the computer goes into hibernation, it uninstall the device drivers for my HP printer.

  When you wake up you can't print anything until it reinstalls the drivers.  Sometimes, it is not automatic, that it will install the printer and drivers so I have to turn off the printer and turn it back on so it can recognize it.  It does not uninstall the printer and the driver when it is turned off and turned back on just at the moment where it goes into hibernation mode.

  Hi SFinOK,

  The best way to solve this problem is to obtain the latest Windows Vista service pack. If there is a reason why you are unable to install the latest Windows Vista service pack, the best thing is to get the fix that is mentioned in Microsoft KB 929734article.

  See the link below for more information:

  You have problems after you resume Windows Vista from sleep or Hibernate computer

  http://support.Microsoft.com/kb/929734

  Let us know if it works

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Why my computer constantly goes into hibernation?

  Hi all ~

  Recently, I noticed that my computer goes into hibernation by itself when not used for a period of time. I confirmed that my power settings dictate this behavior so that plugged in or on battery power.
  Instances that I noticed this, mainly, in mode "sleep" overnight and although slow, act as a "wireless card" for my personal router.
  When this happens, it is not hot or lack of power, he is simply there. I can't find a scheduled task so it hibernates, or an action to be left in standby mode or has been inactive for a while.
  I am really confused and would like if someone could provide an answer, or make me on the right track at least!
  Please help, because it becomes very annoying.
  Thank you
  -Crip.
  Summary and things to know:
  My computer into hibernation by itself, is not a scheduled task so it hibernates, it is not any form of action in my settings to be able to dictate the hibernation, it hibernates generally with more than 90% of battery remaining power and is never hot when it enters this mode.
  My computer is a portable set of bridge NOT running Microsoft Windows 7 Home Premium OS.

  Hello Richter,

  We are here to help.

  For hibernation make unavailable, follow these steps:

  1. Click Startand type cmd in the box start the search .
  2. In the search results list, right-click guest, and then click run as administrator.
  3. When you are prompted by user account control, click continue.
  4. At the command prompt, type "powercfg.exe /Hibernate", and then press ENTER.
  5. Type exit and press ENTER to close the command prompt window.

  Let us know how it goes.

• What would happen if the computer goes into hibernation mode, but there is no free space on hard drive?

  What would happen if the computer goes into hibernation mode, but there is no free space on hard drive?

  No doubt a failure to the hibernation or a nasty system crash - not sure and not willing to risk a stable system there.  :-)

• Problems with Windows 10 screen standby and sleep mode

  After downloading 10 Windows on my desktop all-in-one HP, I have problems with the display of standby and sleep mode.  When the computer turns off, he doesn't have the bright screen.

  After the upgrade to Windows 10, some laptops have experienced one or more of the following symptoms:

  • > Power LED remains lit after stopping
  • > Computer enters standby or hibernation.

  HP recommends that customers see these symptoms first update the graphics drivers by removing and then reinstalling the hardware in Device Manager.

  See the section updating the graphics driver from where can I find drivers Windows 10 and software for my model?

• Evertime I stop the M10 Pro Satellite goes into hibernation

  Hello

  I had one laptop Satellite Pro M10 for awhile now, I recently had to rebuild. I know I have the driver correct graphivs installed etc. Evertime I stop the machine, he goes to Hibernation... I'm at a loss as to wht is the cause.

  Any help would be greatly appreciated.

  Hello

  You intervene on the XP or Vista operating system
  Hibernation has been put on the default Vista. If you really want to stop the laptop with Vista you choose explicitly.

  The XP operating system should stop correctly. If you choose the option stops the laptop to turn off.
  Are you sure that you have chosen the right closure option.
  Sometimes, these options can be confues.

• problems with connecting business valueapps in Windows Vista

  Have rec'd error Windows indicating that logic ValueApps has stopped working:

  Problem event name: APPCRASH

  Application name: ValueApps.exe

  Application version: 1.4.03

  Fault Module name: ValueApps.exe

  There was an automatic update 27/01/14 and, once again, 12/03/14.  I have Windows Vista (64) and have problems of interface with many business websites (online payments, for example) which I have never experienced before.

  Another file is TBverifier.dll; However, that one has not changed since 08/25/13 and don't seem to be a problem.

  What can I do to fix this?  Looks like this are updates of Conduit, Inc.

  Threads merged, but not deleted because it contains additional information about the problem of duplicate

  Hello

  Read this: http://www.shouldiremoveit.com/ValueApps-78723-program.aspx

  Led load Malware.

  Search for malware, if necessary using the safe mode with networking.

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 key repeatedly until you are presented with the Boot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  Once in Safe Mode with network, download and run RKill.

  RKill does NOT remove the malware; It stops the Malware process that gives you a chance to remove it with your security programs.

  http://www.bleepingcomputer.com/download/rkill/

  Then, download, install, update and scan your system with the free version of Malwarebytes AntiMalware in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  And also scan with the free version of SUPERAntiSpyware

  http://www.SUPERAntiSpyware.com/download.html

  SUPERAntiSpyware Free Edition is 100% free and will detect and remove thousands of Spyware, Adware, Malware, Trojans, KeyLoggers, Dialers, Hi-Jackers, and worms. SUPERAntiSpyware features many unique and powerful technologies and removes spyware threats that other applications fail to remove.

  SUPERAntiSpyware Free Edition does not include blocking in real time or scheduled scan.

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  THS is a very good program to scan your system to remove adware, etc.:

  http://www.bleepingcomputer.com/download/adwcleaner/

  AdwCleaner is a program that finds and removes the Adware, toolbars, potentially unwanted programs (PUP) and browser hijackers from your computer.  Using AdwCleaner you can easily more of these types of programs for a better user experience on your computer delete and while browsing the web.

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  And just to be sure, nothing is lurking in the background:

  'TDSSKiller Rootkit Removal Utility download for free'

  http://USA.Kaspersky.com/downloads/TDSSKiller

  See you soon.

• Problems with my Dazzle DVC 170 on Vista (32 bit)

  so here's my problem.  I just got my Dazzle DVC 170 Video Creator Platinum and I have Windows Vista Home Premium and its only good with Windows XP.  So what of heres is past...
  I downloaded the software that came with my Dazzle "Instant DVD Recorder and Studio 10 QuickStart" once this has been done, I tried opening Quickstart and he says its does not work for Vista, but only for XP.  I also tried Instant DVD Recorder and it gave me an error and it says program could not start, closing or something. If, after this, I looked on Youtube to find my answer, and I found the Pinnacle Site to update the drivers.  I did all the updates of software and it did not always work for me... so after that I downloaded other software like start Video Capture and Pinnacle Studio Plus 12, when I used a start, he shut down my computer from one attack and goes into a blue screen, so I tried Pinnacle 12 Studios and did the same thing.  I tried using Windows Movie Maker and when I click the Webcam Capture, he said: it is not all the devices that are on.  I look at my Dazzle and the green lights on, what the devil? I checked Device Manager and it says its there.  But still does not work... Last thing I tried was Picasa 3.  There is a screenshot of the Option of the device... I click it and it says connect to the webcam or device and it gives me a white screen.

  I don't know what to doo more. Please answer!   IM thinking that I did something wrong with the cause of software when I plug my Dazzle in the USB port, said he is ready to use and the good to go!  but his i just could not get the software part.

  Hello
  I suggest you to uninstall Dazzle DVC 170 Video Creator Platinum including all updates related to this software and then try to install it in Windows XP compatibility mode and check.
  http://Windows.Microsoft.com/en-us/Windows-Vista/make-older-programs-run-in-this-version-of-Windows
  See also:
  http://Windows.Microsoft.com/en-us/Windows-Vista/uninstall-or-change-a-program

• laptop is not put into hibernation after "standby mode"

  Reference Dell dear community,

  I have an Insipron 17R core i5 zm2410, NVIDIA Geforce 525 m, win8 64bits and I am facing a problem with hibernation mode / sleep.

  About 2 weeks ago my laptop went mode hibernation after beeing in mode 'sleep' for 2 hours on battery (for total draining of the battery to advoid).

  Now, it is not do it anymore but remains on "sleep" during all the time and drains the battery.

  I usually remove the power cable from the laptop during the night because of the noise of the adapter and the laptop always put into hibernation after beeing in mode 'sleep'. I went over the configuration in options plans and power supply and even reset and configured them again, without success.

  The only changes made to the system are important updates of windows

  I'm grateful for any suggestions or solutions.

  Have you checked to see if Hibernation is still active? Open an administrator mode command prompt and type: powercfg/h on.

• Laptop goes into a spasm of disconnect and reconnect a USB 3.0 drive

  Original title - USB 3.0 unplug plug back

  I have 2 computers running Windows 8 Pro 64-bit. 2 computers have the same USB Microsoft drivers, the same set of Intel chips (both with the i7 processors) from the same manufacturer of motherboard. They have the same operating system, same programs, clean installs with drivers to date and windows updates, they're practically twins with the exception of a material fact; one is one laptop, the other a desktop computer.

  Two computers, although very similar in there profiles of hardware (Device Manager) and in contexts there, seem to have their preferences on what USB 3.0 devices that they like or dislike.

  The laptop will go into a spasm of disconnect and reconnect a USB 3.0 drive, whenever I plug. The office like this player and everything will work day and night. However, when I plug in a USB 3.0 flash drive in desktop and start transferring a file, it disconnects and reconnects the reader, which damages the transfer. The laptop like this USB 3.0 flash drive and will transfer files to and from this day and night.

  Of Corse it's backup and data transfer between 2 computers, although they are very similar, very difficult. Devices USB 3.0 a computer like the other goes into a conniption fit with.

  I tried everything I can think of. Updated, updates to the BIOS, software configurations, reader driver manager settings, different formats of devices, software of turbo boost, installs own, you name it. It is important to note that none of the problems happen with any of my USB 2.0 devices.

  Are there not a universal standard of USB 3.0? 2 computers act as if they have 2 different USB 3.0 standards! And each device will work with a standard computers. Is there a laptop computer and a standard desktop computer? LOL, it's nuts!

  SOLVED *.

  I solved the problem.

  Just ignore my other messages troubleshooting efforts earlier.

  The problem is with the Microsoft Windows 8 driver for:

  "Intel (R) USB 3.0 eXtensible Host Controller - 0100 (Microsoft).

  The Microsoft Driver is dysfunctional , and there is no other driver available!

  I have disabled> Intel xHCI in BIOS on all my computers to get a partial solution to this problem of Microsoft .

  With XHCI disabled in BIOS driver Microsoft dose does not and so I can use USB 3.0 with controller Intel devices (although they are paralyzed, at least they work now).

  As a big bonus:

  My PC has 2 not intel USB 3.0 controllers!

  With Intel xHCI disabled in BIOS and no Microsoft Driver to mess things up that my 2 other controllers can now go full speed USB 3.0 there little made in China drivers! Windows8 should get fixed soon!

• Problem with the Satellite A200 and Windows Vista startup

  Yesterday, my laptop had some mistakes and tried to stop.
  He remained on the screen closed for quite a long time, so I decided to push the power button until it turns off.

  When I went to turn it back to the a started going through the normal screens, the Toshiba screen and then the white screen with the Microsoft flag down. At this point, the screen goes completely black and rest that way.

  Through starting initial power cord, light is turned on, the power supply is on the HARD drive light and then when the screen turns white HARD drive light turns off and stays off.

  I tried to do a system repair using the F8 key at startup and it goes into the Advanced Boot Options menu when I select 'Repair your computer', the light of the HARD drive temporarily, I go through the screens and select System Restore, I selected a date a few weeks and then click Next on the screen indicating the (c :)) system disk is ready to be restored then it returns an error -" (c) drive has errors. Windows has detected corruption in the file (c) system.

  You should check the drive for errors before you can restore it "- and at this point, I can only click on the 'check' the drive to find errors, and then click Start, as he chose the option 'Automatically fix file system errors'."

  When I click Start nothing seems to happen just on the same screen, the HARD drive light does not come on at all and there is no internal HARD drive noise. The only way I can get out of this screen is to turn the computer off again.

  If someone is able to help I would really appreciate it!

  Thank you!

  Hi Cazza68,

  Looks like Windows is confused upward

  Can you start Windows if you perform an installation of Toshiba Recovery disk recovery?

• Run the script automatically when Windows goes into hibernation or wakes up?

  Hello

  I use the group policy feature in Windows XP to run scripts automatically when you open a session or logoff.

  But it is also possible to make a script run automatically, whenever a Windows-xp machine is about to Hibernate? And also when it wakes up from hibernation?

  The clues how to proceed?

  A funny hibernation is that if you put into hibernation and power then upwards and don't 'do' nothing - like press a key or move the mouse (just to sit and watch), in 300 seconds (5 minutes), XP will go back into Hibernation automatically.  Try it!

  XP does because after it comes out of Hibernation, if XP detects that there is nothing to 'do', he thinks he might be from Hibernation by accident and goes back to "sleep" and said "why you wake me up?

  That's why when people hibernate during the night and their machine turn on the morning he wakes up, they make their coffee or breakfast and return later to see that they have the power of their machine again.  If they think something is wrong, but things are working as expected.

  One way to fix this, is to use a third-party tool that uses the command line to simulate a mouse movement.   It is enough to prevent the rehibernating while you are on XP.

  To simulate a movement of the mouse as soon as your system is equipped with Hibernation, you will need to download the nircmd.exe file.

  There are many other utilities of vouchers on NirSoft main page:
  http://www.NirSoft.NET/

  To simulate the movement of the mouse, download the file nircmd.exe here

  http://www.NirSoft.NET/utils/nircmd2.html

  Put the nircmd.exe file in a folder which is somewhere in your path (c:\windows\system32, etc.) or consult the path in your command file. I put the nircmd.exe file in my c:\tools folder where I keep other things.

  If you do not have Hibernate enabled in your Power Options, tab hibernation, it will put your system on Stand-By instead of Hibernation.

  Create a batch file (I called mine hibernate.bat and put the nircmd.exe in my c:\tools folder) and put this line in your hibernate.bat file:

  off @echo
  Powrprof.dll, SetSuspendState c:\WINDOWS\system32\rundll32.exe Hibernate
  c:\tools\nircmd.exe 10 10 movecursor
  movecursor-10 c:\tools\nircmd.exe - 10

  Save the new file hibernate.bat on your desktop or somewhere, you can retain and double-click it to run the batch file.  When you are sure that it works very well, and then drag the new desktop icon to your quick launch area (to the right of the button start), change the icon, rename, etc, so it looks a bit better and then you can click on new quick launch when icon to call the file hibernate.bat.  Now just remember to use the hibernate.bat file (which could be on your desktop with a nice icon) instead of the menu to turn off the computer.

  The first command will put the system into hibernation, and then when XP comes from hibernation (even days later), run the following commands in the batch file.  These last two commands will simulate a slight mouse movement and who will deceive XP into thinking there is a reason to get out of hibernation and it will not go back to sleep.  Then when you come back from your coffee, your system is always waiting for you.

  If your case, your hibernate.bat might look something like:

  off @echo
  order 1 run before hibernation
  2 run before hibernation command
  order 3 to run before hibernation

  Powrprof.dll, SetSuspendState c:\WINDOWS\system32\rundll32.exe Hibernate

  order 4 to run when coming out of hibernation
  command 5 to run when coming out of hibernation
  order 6 to run when coming out of hibernation

• Problems with programs that seek to reinstall vista-fresh start

  Hi, I have big problems with vista next to some of my prgrams that worked in the past have stopped working together, I tried to uninstall and reinstal them. I tried to perform a system restore, and it does not work so I can't do a system restore. Ideally I am looking for reinstall fresh vista but the problem lies in the fact that I have no instalation disk, it has not been provided with my computer and now out of warranty. Any help would be greatly appreciated.

  The information below should help you:

  Vista recovery media obtain and/or use the Partition Recovery Vista on your computer to the factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Also ask them if it is possible to do the recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their own way of making recovery disk/s.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  Save all data, because it will be lost during a clean installation.

  See you soon.

  Mick Murphy - Microsoft partner