Problem with the MK6021GAS as external USB disk

Similar Questions

• Re: Satellite C650 - problem with the devices connected to USB ports

  Hello

  Can help someone, I have a C650 and everytime I try to connect to something to him via the USB ports, it is not "found" by the computer?

  The other night, I tried to get pictures on my phone but it wasn'; work and I put it down to a problem with the phone, but today I tried to install something digital crafts for my daughter and during installation it tells you to insert the thing into the USB port and click Next, when I do that he's going through a lot of "research" and said then it can not be found.

  The laptop makes a beep sound as it would on an extraction device when you plug... I hope that makes sense. So I am now assuming that the problem is with my computer, is there something I can do to fix this?
  Thanks in advance

  Sorry should add - it's like nothing is plugged at all when it is, and it happens on two USB ports, not just one...

  Post edited by: leahhw123

  Hello

  What happens with plug n play like USB mouse device?
  You are able to use an external USB mouse correctly?

  > but today I tried to install something digital crafts for my daughter and during installation it tells you to insert the thing into the USB port and click Next, when I do that he's going through a lot of "research" and said then it can not be found.
  I guess this could be a problem with the software or drivers installed.

  I searched a bit and his city that he has a software is compatible with windows vista/2000/xp. Win 7 is not mentioned do not know if this could be a problem, but in your case, I recommend asking the support of this software product for some advice.

  In addition, you can try to install this software once more, check whether this USB problem appears again.

• SL500, Windows 7: Problems with the interface audio external Firewire and Digitus USB KVM switch

  Hello

  I have an audio interface, Presonus Firestudio Project, which connects via Firewire to my Lenovo SL500. On the Sl500 is Windows 7 x 86 installed. I have also 2 rudders (Akai APC20 and M-Audio UC33e), 1 Midi Interface and a kvm switch connected via USB.

  Almost everytime I make music with Cubase or Ableton Live I get holes in my audio stream. Audio playback stops just freezes for 1-10 seconds and the surface of my DAW. This becomes especially annoying when I record.

  Recently, I have disabled all devices in the BIOS except for Firewire and USB, but I am always running into the same problem. Then I got a look at the system information for Windows 7 and the saw - problems/sharing section - USB and Firewire to share the same IRQ. I'm almost certain that this is the problem causing the audio gaps.

  Is there a way to chanmge in Lenovo Sl500 BIOS IRQ settings?

  Best regards

  belochim

  After Plug and install a USB audio interface that I borrowed from a friend, I noticed that whenever I changed my KVM switch to the surface of the other PC Ableton froze for a second. The audio stream on the other hand kept and just as it was supposed to.

  The KVM switch is a "Digitus Pocket 2-port USB KVM switch" model No. "DS-11402-1".» This KVM switch seem to be a kind of diffusion in the USB bus which then interrupts the audio stream running on Firewire.

• Problems with Vista after disconnecting external USB key without using 'remove hardware safely '.

  A week ago, I unplugged my external Seagate USB drive without using a 'Remove hardware safely' first of my Vista pc.  Since reconnecting the drive, I had a series of problems.  The drive itself seems to be ok.   I am able to read and write to files on the disk.  I'm not able to do is the following:

  (1) open disk management.  It hangs on "Connecting to Virtual Disk Service".

  (2) stopping or starting without windows to snap or take an extra long time to stop or start.

  (3) failed to start Google Picasa3 or Adoble Photoshop Elements 7.  They both hang him.  I am able to use other programs such as Microsoft Office, Outlook, Miro, Norton Antivirus.

  Points 1 and 2 above work fine if the drive is not connected.  I plugged the drive into another computer (Windows 7) and ran Seagate disk checking utility.  He came clean back (no bad sectors) so that the drive is NOT corrupted.  (Check of the Seagate utility disk hung on my pc Vista.)   It seems that something related to the disk under Vista service is corrupted.

  I also see "driver has detected an error in the controller on \Device\Harddisk2\DR2." event message for different devices.  I also tried a restore to a point just before that the problem occurred.

  I don't want to reinstall Vista therefore looking for a solution.  Thank you.

  Janis

  Hello

  You can see the two links below, try the given suggestion and check if this helps you solve the problem.

  http://social.technet.Microsoft.com/forums/en/windowsserver2008r2management/thread/8b5d2c5b-C212-4E3F-96e3-91e668d3b178

  http://social.answers.Microsoft.com/forums/en-us/w7hardware/thread/b2b29ed8-f620-4FE1-93b5-8ced0d472aeb

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• problem with the creation of my usb data card connect to a wifi hotspot network!

  Hello, I have g62005ax machine of hp pavilion and the use of windows 7 home basic service 1 since I bought it, I map of 3g data through which I use internet on my laptop, recently I had a phone android romaric mi3 and wanted to use the net to my data card 3 g on phone via my laptop by creating my cell phone as a wifi hotspot I tried connectify and virtual wifi router and mhotspot, enable me to create a hotspot wifi successfully, my phone can identify them and even be able to connect to the wifi network but I can not surf or download in the phone no matter what app or browser, phone says connected wifi network and phone receives the data as 0.15 0.58, 0.98 KB. My card data speeds work fine on pc on 1 MB/s with no problems, but what is wrong I am doing even after the connection is established?  As I said I tried different pc applications, given that my phone might have problem then I tried another star of the Galaxy samsund phone pro, it also connects to the wifi network but the same problem, IE. No surf, the so problem is not end of my phone, what am I doing wrong here?

  Hello IRON-MAN.

  Thanks for posting on the HP Forums!

  I understand the hotspot of data card USB that you create from your laptop is not working properly. I'll do what I can to help out you! Please follow this guide to make sure that you follow the correct procedures: How to create a WiFi HotSpot with your connection Internet/card USB Data...

  Please let me know your results. If you're still having problems, please provide some screen shots so I have something to look at. Thank you and have a great day!

  Mario

• problem with the transition and external image

  Hello! I have a little trouble with the transition to a new state that contains an external image. I want a titlewindow to resize when the user clicks on a button and view an external image. the size of the external image is unknown until it is loaded, so I put the widths/heights to 100%. However, the transition "resize" does not know the size of the image in time and comes alive in a small rectangle...
  
  I discovered how to solve this problem by deleting the passage and making the invisible titlewindow until the image is loaded (using the event 'complete'). Ideally, I would like to use the functionality of transition, however and am curious to know if anyone has any ideas on this point - perhaps triggering the resizing to start once the image is loaded? I can only find a way to display a transition through mxml - this can be achieved via actionscript?

  When you use States and there is a tag This means that the child will be added to the display list. The object already exists (a new operation has been made about it). It may not be in a fully realized State first because it has not been added to the display list and therefore his complete cycle of creating the Flex framework has not been executed.

  I haven't run the scenario I propose, so it might actually not, but I have another suggestion below.

  You should be able to have in the State that when you are ready to load the image, img.source = url; should not give you an error. The question is, without the image being added to the display list, try even to load image from url and trigger the complete event? If it does not trigger the complete event, then you can change the States there.

  My alternative is to not put the Image in the State, but leave it in your state of base with a width and a height of zero. Having the button set the source property of the image (or call the load() method). When the complete event triggers switch States.

  In your , instead of having an AddChild, you'll SetProperty. Something like this (width, height would be similar):

  Now, the transition must simply use the effect of .

• I have a problem with the headphones C media usb.

  Hello

  I have the C Media USB headphone there the blue plastic on the
  no idea of the model, but when I try to record using headphones don't FRAPS
  There is a constant beep refers to video Youtube:
  http://www.YouTube.com/watch?

  I updated all my drivers and tried various ports and nothing works.

  Thank you

  Hello

  Please answer these questions to better understand the issue.

  1 are you facing this problem just trying to capture the video/audio recording FRAPS?

  2. are you able to hear sounds from other programs and recording using the C Media USB headset?

  3 have you tried to connect the headphones on another computer and check if it works properly?

• Disk error non system at boot when using the external USB disk

  Hello

  I use Windows 7 Pro.  I have a Seagate external USB disk causing a "Non-system disk error" at startup.
  I had the same problem with a Clickfree drive.
  The problem occurs on my other PC with different versions of Windows.
  How can I get my computer to start and not give me this error message for my backup drive?
  At startup (when the drive disconnected), I get a screen of BACK indicating "Client Mac Addr."... GUID..., DHCP. "I think it's looking for a disk boot from.
  I just need to boot from the internal hard drive.
  Thank you
  AS

  USB external references aren't desingned to be connected on startup, you must also use the safely remove the procedure and disconnect the USB key before closing.

  If you get such a screen "Client Mac Addr... etc" at the start (with usb unplugged), looks like you are using a very old motherboard. If the system starts only with connected usb, then your initial installation of victory is defective or damaged

• Problem with the HP G62 recovery disks

  Hello

  I'm having a problem with the restoration of the operating system on your laptop HP G-62. When I first bought the laptop, I was unable to make the recovery discs, so I ordered recently a few new HP. Because I have installed Ubuntu on the laptop, I wiped it from the disk hard drive used Wipedrive to remove the old Ubuntu operating system I had installed.

  Laptop computer reads the first disc ok and installs the component of windows, but when the screen lights up asking the two disc number it freezes and never installs anything when you try to move anything that used to screen it doesn't matter what and he used to install the second disk. He repeats just 'Please wait '.

  Thank you, Robert

  Hi, Robert:

  I can't help you get the recovery disks to work, but if you can read all 25 characters of the product key 7 windows on the bottom of your PC, you can do your own installation disc 7 windows to reinstall the operating system.

  Here's how:

  If you can read the Microsoft windows 7 25-character product key, you can download simple Windows 7 ISO files to burn on a DVD for the version of windows that is installed on your PC, and which is listed on the Microsoft COA sticker on your PC case.

  Burn the ISO with the option to burn the ISO on your DVD burning program and burn it at the slowest possible speed that will allow your program. This will create a bootable DVD.

  Or use the installation of Windows 7 USB/DVD tool to compile the ISO file that you download from Digital River. Link and instructions below. You need a 4 GB flash drive to use the USB compilation method.

  http://www.microsoftstore.com/store/msstore/HTML/pbPage.Help_Win7_usbdvd_dwnTool

  Use 25 characters on the PC product key to activate the installation.

  The key will activate a 32 or 64 bit installation.

  Then go to the support of the PC and driver page to install the drivers you need.

  Link to downloads ISO of W7 is below.

  http://www.mydigitallife.info/official-Windows-7-SP1-ISO-from-Digital-River/

  Paul

• Since 10.11 I have not been able to download via the usb port of my Davis Vantage weather station. No solution of tech Davis on the issue even with the new recorder of events in the resort. Is there a problem with the usb?

  Since 10.11 I have not been able to download via the usb port of my Davis Vantage weather station. No solution of tech Davis on the issue even with the new recorder of events in the resort. Is there a problem with the usb?

  What Mac? (details)

• If win 2003 is upgraded for the 2008 edition, it will fix alingment compensate for the problem with the SAN disks?

  If win 2003 is upgraded for the 2008 edition, it will fix alingment compensate for the problem with the SAN disks?

  Hi elvirkaric,

  Your question in Windows Server 2008 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Forum. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en-us/w7itproinstall/threads

• Error - there is a problem with the external Setup program and it must be closed when you try to install windows updates

  Original title: How can I fix external MSI?

  When I try to download the updates, the error message says there is a problem with the external Setup program and it must be closed.  Updates will not be installed.  Anyone know how to solve this problem...?

  Hi John,.

  ·         You are able to install other applications on the computer?

  It seems to be a problem with the corruption of the .net framework. I suggest trying to repair the .net framework on the computer and see if you can install the updates.

  http://support.Microsoft.com/kb/923100

  Hope the helps of information.

• Problem with the disk check.

  32-bit Vista Home Premium:

  About 6 months ago, I ran a Check Disk from my C drive (using Vista error checking tool) and checked the two boxes before starting (fix Auto file system and search for errors / attempt to recover bad sectors).

  He ran through the 1 5 6 controls without finding an error.

  On the 6th and final verification that it is running, it hung (or the 4th of 5 controls it works - do not remember if it is 5 or 6 it works). According to me, he started the final control, but stopped and none did not move. A few hours later he still hadn't moved, so I did a hard stop.

  Fortunately, everything was fine when I rebooted.

  I use the computer since then without problems/errors obvious hard drive, but I'm afraid to run another check of the disk, even though I would right now.

  Suggestions are welcome as to what might have caused the shot, and if I do another check of the disk.

  Yes, it's essentially the same command.  Personally, I never use the other method - I just use the one that I you provided.

  : You are right about the meaning switches - you already know or you're an awfully good guesser.  Since you have expressed interest, here's more information on CHKDSK you might find of interest with other switches and guidelines and some good information on how it works and how to use the results: http://www.vistax64.com/tutorials/67612-check-disk-chkdsk.html.

  If you cannot complete a cHkdsk on your hard drive, then there is a problem with the player that must be resolved before it is any worse.  I would definitely give it another chance and also run the diagnostics that I recommended in a previous post.

  I hope this helps and I hope that the test completes successfully this time.  If this isn't the case, I hope that the diagnostic test identifies the problem and it can be repaired than replaced (even if it's pretty rare - usually if it goes wrong it must be replaced).  If this is the case, I would as soon as possible to ensure that it is not so bad that you can no longer access the drive at all - but then again, there may be nothing wrong and we could be worrying for nothing but a bad block or two which is nothing to worry about in itself.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Video device USB has a driver problem__ __There is a problem with the driver for USB video Device.__Device information __Name: __ID USB video device: USB\VID_05CA & PID_180C & MI_00\6 & 69C3BD0 & 0 & 0000 code __Error: 10 _ _ _

  I hava a dell inspiron 1440 with windows 7 and a a few days ago, my webcam was working just fine but know that it gives me this after troubleshooting

  Has a USB video device driver problem

  Not fixed

  There is a problem with the driver for USB video device. The driver must be reinstalled.

  The device information

  Name: USB video device ID: USB\VID_05CA & PID_180C & MI_00\6 & 69C3BD0 & 0 & 0000 Error code: 10

  Hey laloo.16,

  As the error message states clearly that reinstalling the driver is required, please do the same. You can uninstall the driver that is currently installed from the Device Manager.
  To access Device Manager:
  1. go to start and type Device Manager.
  2. Select Device Manager in the control panel list.
  3. go to your device.
  4. to remove:
  Right-click on it and select Properties.
  5. Select the driver tab and click on uninstall to uninstall the existing driver.
  6. close Device Manager.
  Now go to the link below. Download the Dell WebCam software for your product.

  http://support.Dell.com/support/downloads/DriversList.aspx?OS=W732&CATID=-1&DateID=-1&impid=-1&OSL=en&typeid=-1&FormatID=-1&SERVICETAG=&SystemID=INSPIRON1440&hidos=WLH&hidlang=en&TabIndex =

  Please choose the appropriate version of Windows 7.  Install the driver and see if that brings your webcam to work.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problem with the disk free space.

  I use the power of fire 7100 (the 5.3.0.3 Version of FireSight 5.4.1.7 sensor Version). I have political problems that apply to the device. And is unable to update sensor for the newest version. Cisco support community help me! Thank you! They and I think that this problem can be in the use of the disk.

  What I oh sensor:

  Size of filesystem used Avail use % mounted on
  / dev/sda5 2.9 G 562 M 2.2 G 21%.
  / dev/sda1 99M 37 M 58M 39% / Boot
  / dev/sda7 67 67 G 0 100% but
  No 1.9 G 136 K 1.9 G 1% / dev/shm

  May be the problem with the records of Volume.What I could check and delete? Thank you!

  Hello team,

  * Could you please check the following points: -.

  CD/var/tmp /.

  du-sh *.

  You can clear the/var/tmp/en using the following. Files under/var/tmp temporary files are. :-

  rm - rf *.

  It is a known bug where the but gets completely due to Apply_ files *.

  * Also check the following points: -.

  CD/var/sf/updates

  Remove the old patches if there are.

  * Check the following backup folder and the folder of detection engine too.

  CD/var/sf/upgrade_backup

  du-sh *.

  CD/var/sf/detection_engines

  du-sh *.

  Rate if this helps you.

  Concerning

  Jetsy