Problems connecting Toshiba L64 TV network home

Similar Questions

• Irregular problem connecting to the wired network

  My Windows 7 PC has an irregular problem, connect to the local network of cable through a provided network of the netgear modem/router.

  The connection timeout is the question and sometimes takes a while four two minutes or more.

  A reboot of the pc never seems to resolve but (quite often, in fact usually) will be a restart of the modem.

  The modem is always on (as the announced network connection is supposed to be).

  The network provider has replaced the modem, and the problem persists. This leads me to believe that there is a start up or similar problem with the pc.

  I ran the troubleshooter in windows... no chance/results. Is there a "fixit" tool I could try or something similar?

  Happy to clarify, to provide more information and appreciate any input.

  concerning

  Lethal42

  Hello

  Thank you for your response. I appreciate your time.

  I suggest you to refer to the link below and check if this is useful:

  Wireless and wired network problems:

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1

  Hope this information helps.

  Sincerely,

  Ankit Rajput

• problems connecting to the wireless network - the network (no internet access) proxy setting

  Former title: yellow triangle wireless

  My computer can connect to the wireless router but cannot connect to the internet. I try to connect with the ethernet with cable modem connection & it still does not work. The other laptop works fine but my does not.

  1. I have uninstalled & installed the network card.

  2 restart the apater modem & network cable

  3. I get 'Windows could not detect a network proxy setting.

  4. when I "Network & Sharing Center" and under "show your network activity" I get "identification."

  5. "identiyfing netgear" below said 'no Internet' when you are connected to netgear

  Windows IP configuration

  The host... name: Jeffrey -.
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Virtual WiFi Miniport adapt
  Physical address.... : 1C-65-9D-BF-E2-BF
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  Description...: Realtek RTL8188CE WLAN 802.11n PCI-E NIC
  Physical address.... : 1C-65-9D-BF-E2-BF
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::cc8f:f2cd:dd7c:ccd1% 17 (Preferred)
  Autoconfiguration IPv4 address. . : 169.254.204.209 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  DNS servers: fec0:0:0:ffff:1 1%
  FEC0:0:0:FFFF:2 1%
  FEC0:0:0:FFFF:3 1%
  NetBIOS over TCP/IP...: disabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  Description...: Realtek PCIe FE Family Controller
  Physical address.... : 1C-75-08-73-8F-F1
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {342574F9-0D0B-4337-B59D-E7373E959066}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {25F2C90C-9E95-491A-BDFC-4F4CDA2FE33D}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Adapter Microsoft ISATAP #2
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 12:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Hi istraight1,
  a few steps, I recommend you to see exactly what this question:
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  and
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/Windows-could-not-automatically-detect-this/d243dea1-d1c8-4C4A-ba96-2b49bc9bab1a?TM=1338167520088

  and finally:
  http://social.technet.Microsoft.com/forums/en-us/itprovistaprinting/thread/548ca07e-F04E-4973-8719-8c09959f1ca6hope this helps.
  B Eddie

• problem connecting to the wireless network, but it worked yesterday.

  Yesterday, I was able to connect to my home wireless network, but not today. I also have a laptop and it connects to my wireless network, there must be something with the RT of Surface.

  Home Wireless works, why can't connect?

  Your post is off-topic in the forum Feedback, I moved it on the forum of "Web and Networking" Windows RT.

• Suggestion for connecting NetGear switch for network home

  Hi all

  Recently, I bought NetGear ProSafe 8 - Port Gigabit Ethernet Switch GS108E. I would like to ask your help/suggestions to connect to my home network. The other components I have is Motorala SurfBoard SB6121 Cabel Modem and Cisco Valet M10 Wireless router.

  I have a Comcast Blast Plus service and if I check my internet speed by connecting my laptop directly to the cable modem, I get 50 Mbit/s Download and Upload of 11 Mbps. If I connect my laptop to the ethernet port of the router the speed I get is 25 Mbps download and still 11 Mbit/s upload. 50% reduction the internet download speed. So I decide to buy a NetGear Switch so that I can run all my connection cable of the switch and wait for the speed of download of 50 Mbps and 11 Mbps Upload.

  I made the connection like cable Modem--> Switch NetGear--> wireless router. In this configuration no my devices are able to connect to internet and I get message unidentified network. I tried to troubleshoot using the Windows Connection Manager, but he just asks me to turn off and on again. I tried this several times, but was not able to solve the problem.

  I want to return to the NetGear Switch mannual and made connections like shows in the quick installation guide. Cable modem-->--> Switch NetGear wireless router. In this configuration, all my devices are able to connect to internet but I get the speed of 25 Mbps download and 11 Mbps upload, identical to what I was getting into when running connection wireless router wired thorugh.

  So, essentially, NetGear switch does nothing for me except give me a few more ports to run the wired connections.

  It would be a great help if someone can guide me in the resolveing of my problem.

  Kind regards
  Shekhar

  He had bought a new router in the first place. Your router is the problem. Check on their website for a solution.

• problems connecting to unsecured wifi networks of (starbucks, McDonald's, etc.)

  I have a Dell laptop, I tried to connect to unsecured networks. When I pull up available networks immediately by the unsecured network icon, it is an exclamation that she. When I select to connect, it still says that it is connected, but there is no internet connection. I tried to disable the antivirus and firewall mg temporarily, but it makes no difference. I have a private wifi in that this isn't a problem with me. Anyone have solutions. My windows vista 64 bit is completely up to date.

  Many wifi networks out there do not work with the 64-bit versions - they (wifi in these places devices) require special equipment and/or additions and additional software may (if those that they can be improved without buying a completely new camera) and many simply don't bother or have money or consider that the number of people with a problem they need to address.  I suspect this is the case, that you face – I saw happen with many others.  I don't know there is nothing you can do about it except complain (and perhaps someone will listen).  The fact that you can connect at home means that your system works correctly - it's the Wi - Fi connection in those places that can not connect to your 64-bit version.

  Unfortunately, the 64-bit isn't the main stream quite yet and so always these compatibility issues exist (and will probably be for some time to come).

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Problems connecting to the local network with NAS

  So we have a private network to work. On this network we have implemented a Synology NAS. We are constantly backup of files, files, adding files, etc. updated excel... There is a lot of traffic on this subject. Recently it was kickoff of people with error messages like "Device name already in use. It could be a problem with just the NAS, but I think it might be a problem with the network or something that I could deal with different parameters. The problem occurs when there are a lot of people on the network, not necessarily work outside the SAR, which has a static IP address. Because of my ignorance of networks, I don't know what information to include to help describe the problem or put in place, so do not hesitate to ask!

  Any help would be greatly appreciated, more on only an opportunity to learn more about networking is also good!

  Hi Michael,

  • What operating system do you use?

  I suggest you to send your query to the TechNet Forum for better support.

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?category=Windows10ITPro

  Kind regards

• Problems connecting to internet - says network cable disconnected, not sure I have the correct driver installed.

  Had a big storm - got the new modem.  but they said that my drivers where missing or damaged.  Downloaded Marvell Yukon of gateway - to the GT5432 model. Always says cable unplugged network. However, Bishop says peripheral device works correctly. Don't save: no update-unable to connect to the internet.  I uninstalled and reinstalled; rebboted, etc. - still nothing. It has a problem with the PCI connection - no driver, but I don't see anywhere to down load or know what to download. Oh and another adapter on - think 1394 - when I turn that on and off the wonder; It shows the signal for the 1394---400 and does not say his unplugged, but still can not connect to internet.
  The "old" computer to try to find information; noticed that said, unplugged network cable but it allowed me to connect to the internet. When I disabled the 'extra' adapter message there went, speed signal only at 100 than at the 'old' calculation is not any other PCI devices connection listed.

  I'm not sure of what continues.

  The 1st computer was working fine - then picked it up to move it to where it belonged to my office and that's when he went out-made no sense to me!

  Because you seem comfortable opening your computer, have you tried re - a corner of the map (with power off, remove the card and reinsert it into the slot, be sure to exercise static precautions if you are in an environment of low-hu7midity).  If there is an empty slot, you can also move the map Marvell to another location.  See the comments below.

  It's a long shot, because even if you did not provide the complete ipconfig output, the data that you have provided appeared to be normal, but...

  Open network connections (start > run > ncpa.cpl > OK)
  Right-click on the icon for your network adapter, and then select Properties
  You should see a screen like this--> http://screenshots.modemhelp.net/screenshots/Windows_XP/Network_Connections/Local_Area_Connection/Properties/General/Index.shtml
  Issues related to the:
  In the upper area, under 'Connect using' said 'Marvell Yukon 88E8039 PCI-E Fast Ethernet Controller?  If this is not the case, what does say?

  In the second box, what are the items are listed under "this connection uses the following items"?

  The only other thing I can think is that the Marvell Ethernet card was damaged in the same storm that got your original modem/router.

  *******************************************

  According to Gateway, the GT5432 has 4 card slots:
  A PCI Express x 16 (GUI)
  A PCI Express x 1
  Two PCI Conventional

  Your motherboard should look like this:
  

  Orange, top, connector is the PCI Express x 16.  You probably have a video card in this slot.

  The short white connector is the PCI Express x 1 connector.

  Two more long white connectors are the standard PCI slots.

  If I understand your installation, you should have the Marvell Yukon map into the slots of two down and your Agere modem on the other.  As long as you have the SMC1244TX PCI card, why don't just remove you the Agere modem or the card Marvell and insert the card CMS in one of the two PCI slots?  You are not using the modem and the working hypothesis is that the Marvell card does not work, so there is not much to gain by leaving a card in your computer.

  Download the user guide and drivers for the SMC here--> http://www.smc.com/index.cfm?event=viewProduct&localeCode=EN_TUR&cid=9&scid=51&pid=238 map

  Moreover, assuming that your open slot is the short PCI Express x 1 slot, you can buy another Ethernet card that will work in this niche: see--> http://www.newegg.com/Product/ProductList.aspx?Submit=ENE&N=100010064%20600016290&IsNodeId=1&bop=And&Order=PRICE&PageSize=100

  If I were you, I blow up the cheaper models and get the Intel EXPI9301CT $ 36 10 / 100 / 1000 Mbps PCI Express Desktop Adapter Gigabit CT.  Note that this is the same card with a similar name (with close to 400 customers) which sells for $29,94.  The price difference is because the cheaper "BLK" letters in the description, which means that it is "sold in bulk" and has no drivers, user guide CD or anything else in the box.  There are several negative comments from people who do not understand this difference and then had trouble finding the driver for the card on the Internet.

• Problem connecting to 802.11n networks on Vista or Windows 7

  Hello

  Under both Vista business and Windows 7 Enterprise, I can connect to an 802.11n network only if the computer has not slept or hibernated. If the computer is asleep or in hibernation, I can connect is a 802.11n network until I restart. However, I can still access the 802. 11b / g fine after sleeping.

  Is this a problem driver or a matter of Intel 5100 AGN.

  One of them was to disable "Energy savings" in Manager device for the card, but that seems to make the system from time to time wants a blue screen.

  Not sure if it's a hardware problem, driver problem Intel or a Windows problem. Maybe someone could put a good solution, the version of the driver or the hotfix.

  Updates Microsoft or updates to Lenovo Power that came out last week corrected it. I had no need of updates to Intel.

• Problems connecting to the wireless network windows media

  After having installed AT & T u verse, the installer said I have to use the code of encryption key for the modem/router to connect to wireless network windows media, so I can watch TV.  Windows Media repeat myself that it's the wrong key code. I checked the number again once and he's right. Any help?

  Hello

  I suggest you to visit these links and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows-Vista/sharing-media-on-a-network-using-Windows-Media-Player

  http://Windows.Microsoft.com/en-us/Windows-Vista/watch-TV-in-Windows-Media-Center

  It will be useful.

• Having problems connecting to a wireless network

  How can I start the Wireless Zero configuration 871122 service article Microsoft Knowledge Base?

  Hi JoseAlonzo,

  Take a look at the steps in this section to configure Wireless Auto Configuration.

• Results of Toshiba Connectivity Doctor or Vista network & sharing Center

  I bought a 802.11n router to allow additional coverage of my Toshiba with a 802.11n Wireless WiFi Link 4965AGN give me and I never seemed to get the extra than I expected! I tried etc. Since a few weeks I got the laptop, and was beginning to lose patience and hope of ever is it solved, however I just noticed something that only confused me even further!

  I always use the connection to a network/network and sharing centre within Vista OS under my control, "connection status" of my networks etc. & it has never showed that the network which should give me ' isn't a 'g '! But earlier I found and used the Toshiba connectivity doctor, and I found it is sometimes shows the connection as a 'n', but still the Vista "connect to a network & Vista network and sharing Center" show the same broadcasting as a 'g '!

  What should I take as the most accurate, I have little additional coverage when I used to have a portable 'g' and a router 'g', but perhaps remotely an additional 2 meters which, depending on how wonderfully better is the "n" does not seem to live up to the expectation!

  I based my results of the exact coverage, physician connectivity Toshiba or Vista network sharing Center, they can be opened at the same time and showing the different results? I do not understand why they say different things? Crikey Ca? s driving me crazy!

  Hi friend

  already tried INTEL drivers? Theres a special broadcast of the site just about your wireless card, so if you please, visit this site and download the drivers from here:

  http://support.Intel.com/support/wireless/WLAN/4965AGN/

  Maybe it s just a driver related problem. And another suggestion: use a single program to connect to wireless networks. Maybe they cause some internal conflicts in the system which turns off the feature n.

  Oh, and Don t forget to check the properties of the device manager/network on some technical parameters. Perhaps, it must be explicitly enabled, also on your router.

  Welcome them

• Problem with the primary dns server, get the error "There could be a problem with one or more network adapters on this computer."

  Hello

  I was all of a sudden having problems connecting to my wifi at home. When I was diagnosed, he says cannot communicate with primary dns server. I tried all methods in similar positions, but nothing works. I am also unable to connect to internet with my iphone and the itouch. It's really frustrating, because I've already tried all of your suggestions. I just ran another ' diagnose connection problems and it says the following:
  "There could be a problem with one or more network adapters on this computer." Help, please!
  Thank you!

  Thanks for your help, but I have tried this before. In the end I just unplugged my modem and plugged in again and it worked? I feel a bit silly not to try first.

• HP Pavilion 15 laptop: Solved: unable to connect to my wireless network

  I have problems connecting to my wireless network. In available connections, my network is there with an x next to it. I can click on it and put my security key in, but it says unable to connect to the network. I've updated ready network cards. Any help would be greatly appreciated.

  Bobby

  Thank you for all your help. I'm back on now. I started having trouble a few weeks ago. My wifi connection would pass, and I have to disable and then re activate my network card back. This has been relatively shortly after my upgrade from Windows 10 but not immediately after. Then the other day which didn't work and I could not connect at all. I read somewhere to try to uninstall the network adapter and then restarting. It did not work. I also read to find updates for the network card and install those which, as mentioned by ichi730 as well. This no longer works. Then, I realized that I had not tried to restart the router after reading the post of WyreNut. It worked, thank you! I feel that it is a combination of the two pieces of advice that have worked so.

  Thank you all for your comments, it's much appreciated.

  Bobby

• cannot connect to the local network using windows 7

  Recently bought a HP Pavilion laptop (AMD Athlon II P320 Dual - Core) ((G62 - 208CA)). Having a problem connecting to the local network. I have flashing lights on the lan (orange and white) connector.

  Using the ipconfig command, I get an IP address, subnet mask and gateway by default however messages below will appear:

  Tunnel adapter isatap. <578608BD-22EF-4A01-90ED-D709CB81D027>:

  State media: media disconnected

  The connection-specific DNS suffix. :

  Tunnel connection to the Local network adapter * 9:

  State media: media disconnected

  The connection-specific DNS suffix. :

  Tunnel adapter isatap. :

  State media: media disconnected

  The connection-specific DNS suffix. :

  TEREDO TUNNELING Pseudo-Interface tunnel adapter:

  State media: media disconnected

  The connection-specific DNS suffix. :

  Tunnel adapter isatap. our field: *

  State media: media disconnected

  The connection-specific DNS suffix. :

  I tried to turn off the firewall and connect without success

  My network card is a Realtek PCIe FE Family Controller and confirmed that the drivers are up to date

  Any help would be appreciated

  Thank you

  Well Yes! So it was an older version of the bonjour service... thank you Adobe.

  You can find the latest version here:

  http://support.Apple.com/kb/DL999