Problems of acquisition & visualization: fails at 100 Hz, OK more low or more freqs

Similar Questions

• I have a problem of "Secure connection failed", access to an HTTPS site.

  I have a problem of "Secure connection failed", access to an HTTPS site. It is of this type:

  Your certificate contains the same serial number for another certificate issued by the certification authority. Please get a new certificate containing a unique serial number.
  

  (Error code: sec_error_reused_issuer_and_serial)

  OK, I have not read the support article carefully enough - it even says that this dialogue cannot be exceeded by adding an exception.
  you are most likely right that this problem arises because the same cert is used for different sites. this support article describes a work around, but it is probable, not applicable to your situation, since you would also have to remove the certification authority and which would create all sorts of problems as your production site will tend to choose an a valid CA certificate.

  Please contact your IT department or the problem of certificate on two different servers or to allow you to run a version of portable firefox where you can mess with the certificate store and the authorities of trust in order to access the test server.

• Receive emails "there is a technical problem. Try again"fails after after many attempts to open.

  Two problems: -.
  1. certain emails receive State "there is a technical problem. Try again"fails after after many attempts to open.

  2. I get Emails with Photos as attachments or a text document. When I send teas on friends the recipient says - no image received

  7 Windows Yes uses customer access to Emails
  Provider is TalkTalk

  
  What client? If WLMail, ask here.
   
  Windows Live Mail Forum
  http://windowslivehelp.com/forums.aspx?ProductID=15

• Recent problems of following Win7 failed to install software from Comcast

  Don't know where to start.  I can only suspect that all the problems are related to a single event and the more likely event, due to timing, has been a download, but Comcast Office software installation failed (automated in Comcast cable internet installation).  I suspect also that because only one sent to 'freeze' the problems here mentions conflict with the AV software and AV drivers may have been part of the package of Comcast.  Don't know.

  PROBLEMS:

  I can't uninstall the software.  Windows Installer "hangs" on "Preparing to install" and nothing happens.  I have to force close with the Task Manager.  Usually, that corrupts the images of my office, removes all the desktop icons and the Start button, forcing me to reboot.  (Near as I can tell, install the Manager affects Explorer.exe some how.)

  I can't install the software. The same problem. The program hangs indefinitely on "Preparing to unistall."

  After attempt to cancel install or uninstall events (default) after forcing the closure with the Task Manager, and after the Office covers without icons, the button start and the bar application (as if Explorer had closed, but froze on the chart in office), by withdrawing to the Task Manager to correct this, I chose the option "disconnect".  This allows me to disconnect and then reopen it in one.  However, once connected, I hit a black screen and the Task Manager shows a lot of applications is open twice in the list of open applications - and resident drivers.  It seems that the original 'disconnect' did not stop those apps, but the 'log back"repeated their.  It ends with a black screen every time and requires the computer to be turned off (where it crashes and then on the "shutting down" screen.)  See below.

  Restart or stop mode, closing blocks indefinitely. Occasionally, there is some disk activity hard, but in most cases, once it freezes, the hard disk is idle - but the computer does not move out of the blue 'Stop' window

  Microsoft Fix It will start, but will block indefinitely on "problems."  Review of activity in the the Task Manager, the program once hung in the "detection" uses no processor and record any activity. Rarely, the hard drive light flashes and doesn't show any use of research. Cancel will close the program without the need to force close with the Task Manager.

  04:00 - Windows Media Center to "optimize" attempts and crashes in the process.  The next morning, when found, WMC is frozen, will not respond to the mouse or remote control and must be forced closed in the Task Manager.  Once done, Win7 and WMC act normally unless specific other problems above.

  I also note that Microsoft Updates have been found and downloaded but haven't installed auto.  At least three recent updates are sitting waiting for my permission to install.  A Java Update yet, so.  Normally all these install automatically without my permission.  After an indefinite period, the close button appears that updates are waiting for a re-boot. I have allowed to happen once--sitting with a window "Please do not unplug or force close - update install" 9 hours - at work.  The machine was frozen.  No evidence of the update took place and all listed pending updates are pending.

  I run Microsoft Security Essentials and PC Tools Firewall more and feel confident that no virus does not cause this problem. If I were an academic assumption, the machine seems to block a lot of temporary programs who want to read or write to the hard disk.  But not all, as I stream video, record TV broadcast in WMC, use Firefox and Thunderbird - all without any problem.

  As I definitely want to remove the Comcast installs and a remote program of ESPN WMC get Windows Installer working properly is quite critical.  Wanting to use the program Fix It to review and fix registry problems is also strongly desired.  Here, your recommendations will be greatly appreciated.  Thank you.

  Phew!  What a ride.  But it seems that it's over.  Here are the details.

  Recovery always disc manufacturer's software on the open - so I couldn't do the disks.  All diagnostic HPs also hung on open software.  The HP site so their software were so any relief.

  I ran chkdsk /f and chkdsk/r with no problems found.  I ran the diagnostic memory of Win7 with no problems found.

  Because my last change encouraging (get the MSE to install a virus definition update) happened when I was able to stop WU Setup with "net stop wuauserv" I decided to try again.  It appeared to fail the first two attempts (each after a reboot), but by the fourth attempt and restarting, I managed to close.  The immediate change was amazing.

  However, another caveat.  At the time of the software of Comcast has failed, install the 10/26 and as the failure of the system, Flash and MSE updates began editing, I had also signed a 80 GB USB flash drive to the system. Read about similar problems with Windows 2000, I tried unplugging my LAN to see if it was the cause of the conflict.  (The LAN connection was started 10/26 - connecting the device to the router to Comcast).  There was no change.  I rebooted, I decided to unplug the 80 gig USB drive in case it was cause of conflict.

  OMG.  Either due to the success stops Installer WU of the unplug of USB or both-, I got a clean shutdown - no blocking.  Windows open in record time and as I began checking the integrity previously does not apps, MSE prompted me to fast and ripped analysis through completion in time record (I ran a full scan later without any result of virus.)

  I have considered a 'net start' but decided against it, as the machine was finally functioning normally.  The failure of the single application has been and continues to be: PC Tools Firewall.  Apps, I wanted to uninstall and other pending installation, all worked perfectly. Looking to restart, the listed stop one button update pending (not sure if it was a system) and that too worked without problem. A single update took 20-30 seconds and then stop without hanging up - as she had for more than a week.

  On the other 4 hours last night, the machine appeared to be back to work properly in all areas except PC Tools Firewall.  What had caused this wonderful series of problems disappeared - either because of the "net stop" or the removal of the 80 gig USB drive - or both.

  I have not restarted install WU by using "net start" and I have no immediate plans to do so. (As far as I know, it restarts after a few restart.)  I will check the State of system update soon and restart, if necessary.  But in getting my machine in perfect health, I will be slow to install WU get reactivated by me.

  Regarding the USB, I'll have to check on another machine.  I had used for port of some files on my machine (for portability) and do not need what he fixed permanently to this PC.  It worked without error during file transfer and I am unaware that she had no failures that could affect the PC.  Never the less, as disconnect seems to coincide with getting the health of my back of the machine, I won't be in haste to reconnect it.

  Thanks for your help.  Like I said, it was quite a ride.   But I think I'm out of the cold, dark woods and running with a sound machine once more.

• Deployment failed due to one or more of the returned errors

  Hi all

  JDev: 12.1.3

  I am getting below error while deploying the application in the Android emulator

  Installation of the platform:

  Location of the SDK: D:\android-sdk-windows

  Location of Android platform: D:\android-sdk-windows\platforms\android-17

  Android built location: D:\android-sdk-windows\build-tools\17.0.0

  Error

  [17: 28:50] copy of the adfmf file - manifest.properties...

  [17: 28:50] start to archive the folder "/ C:/JDeveloper/mywork/CalendarApp/deploy/Android2/java_res/assets / ' to 'assets.zip '...

  [17: 28:54] deployment of Cordova Plugins...

  [17: 28:54] copy the plugin "CalendarPlugin" resources of C:\JDeveloper\mywork\CalendarApp\ApplicationController\src\plugins\CalendarPlugin\Android\res to C:\JDeveloper\mywork\CalendarApp\deploy\Android2\res...

  [17: 28:54] copy the plugin "CalendarPlugin' active C:\JDeveloper\mywork\CalendarApp\ApplicationController\src\plugins\CalendarPlugin\Android\assets to C:\JDeveloper\mywork\CalendarApp\deploy\Android2\java_res\assets...

  [17: 28:54] Creation of unsigned Android application file...

  [17: 28:54] run command line: ["D:\android-sdk-windows\build-tools\17.0.0\aapt", p, - debug mode - f, - m, - J, "C:\JDeveloper\mywork\CalendarApp\deploy\Android2\src", "C:\JDeveloper\mywork\CalendarApp\deploy\Android2\AndroidManifest.xml" -, M, - min-sdk-version, 15-, target-sdk-version, 9, - name version, 1.0, - version-code, 1, - extra-packages, oracle.idm.mobile, - F, 'C:\JDeveloper\mywork\CalendarApp\deploy\Android2\CalendarApp.apk', - I, 'D:\android-sdk-windows\platforms\android-17\android.jar', - S, "C:\JDeveloper\mywork\CalendarApp\deploy\Android2\res"] "C:\JDeveloper\mywork\CalendarApp\deploy\Android2\java_res"]

  Invalid resource directory name [17: 28:54]: C:\JDeveloper\mywork\CalendarApp\deploy\Android2\res/readme.txt

  [17: 28:54] command-line execution failed (return code: 1).

  [17: 28:54] run command line: 'D:\android-sdk-windows\build-tools\17.0.0\aapt' p - debug mode - f m-J 'C:\JDeveloper\mywork\CalendarApp\deploy\Android2\src' m 'C:\JDeveloper\mywork\CalendarApp\deploy\Android2\AndroidManifest.xml' - min-sdk-version 15 - target-sdk-version 9 - name - version 1.0 - version-code 1 - oracle.idm.mobile extra-packages - F 'C:\JDeveloper\mywork\CalendarApp\deploy\Android2\CalendarApp.apk'-I 'D:\android-sdk-windows\platforms\android-17\android.jar"s 'C:\JDeveloper\mywork\CalendarApp\deploy\Android2\res' 'C:\JDeveloper\mywork\CalendarApp\deploy\Android2\java_res '.

  [17: 28:54] Server Android Debug bridge closure...

  [17: 28:55] undeployment.

  [17: 28:55] - incomplete deployment.

  [17: 28:55] deployment failed due to one or more errors returned by "D:\android-sdk-windows\build-tools\17.0.0\aapt".  What follows is a summary of the returned error:

  Command-line execution failed (return code: 1).

  Hi Richard, Arun

  Problem has been solved now.

  Question is is that I created a folder for the project of jdev. Created file's readme default text in it.

  Causing the problem while deploying the application

  Once, I deleted all the readme .txt file in default the entire file. Problem solved.

  Thanks for the effort.

  Kind regards

  Krishan

• you have the problem when I plug in my laptop, the brightness is low.

  you have the problem when I plug in my laptop, the brightness is low.

  No, when I plug it into electricity, it's low.

  It's usually the other way around... check the power settings. If you find my answer helpful, please click the button "Vote as helpful"! Thank you! My Blog

• WRT160N, auto-negotiation has failed at 100 Mbps, can wall jack be the cause?

  Hello

  Can someone please help me with may be a simple problem for you, but it starts to drive me crazy. Sorry in advance for the long post.

  WRT160N installed in the basement, linking (cable) 3 desktops and 2 laptops (wireless). When connecting by wire, some computers have troubles in autonegotiation speed, always end upward with connection failed. Force the speed of 10 Mbit/s full duplex solves the problem.

  Curiously, both computers have no problem to 100 Mbps Full Duplex auto-negotiation (HP nc8430 laptop with 5 years and the Broadcom NetXTreme Gigbyte old IBM ThinkCentre M50 8189-Tower network chip, I do not know the exact network chip, but I think that until the Gigabit). Less than 1 year of office by using a Committee of Asus P5N7A-VM with the integrated Realtek, also Gigabit network chip, still FAILED to negotiate at 100 Mbps. The wall plate has 4 Sockets. The question above is the same regardless of any plug used.

  After several attempts, I think I've isolated the cause to the wall outlet. There are about 6 metres of cable (~ 20 ft) between the router and the wall outlet. The computers connect to the wall using a cable of 2 meters (~ 7 ft). Go through the wall outlets, I pulled a 10 meter cable (~ 30 ft) connecting the router directly to the computer, then the computer is not always to 100 Mbps now could connect without any problems. So, this seems to indicate that the wall socket has altered the quality of the signal.

  The cables (between the router and the wall) are straight with T568B wiring (http://en.wikipedia.org/wiki/T568A/B#Wiring) the sockets are CAT5 RJ45 Keystone Jack free tool (http://www.amazon.com/CAT5-RJ45-Keystone-Jack-Black/dp/B000BSN7RO)

  So here are my questions:

  Q1. A wall outlet would cause a loss of significant signal or alteration?

  Q2. If the wall outlet is the cause of the loss of signal quality, how is it some computers have no trouble to autonegotiation to 100 Mbps Full Duplex and also when forced to 10 Mbps FD, all network problems disappear?

  Q3. And the most important question: can you please provide a solution?

  Thank you very much in advance for any help.

  Hello

  Follow up and FINAL solution to close this thread. The cause was the wall outlet. All sockets are of the type version tool-less Keystone Cat5e. All the exihit speed negotiation issue and can be used at 10 Mbit/s full duplex.

  I could borrow a punchdown tool and tried a new plug. This time, I tried Keystone Cat6 jack _WITH_ tool. Can be overkilled my cable is Cat5 only. But I don't want to take any risks because the price difference is negligible between Cat5e and Cat6 decision. The new Jack is working perfectly. The AutoDetect computer easily at 100 Mbit/s/s. The fix is so obvious, as soon as I replace threaded plug by a Jack of tool WITH the speed issue disappeared. I have connect / disconnect several times, even restarted the computer to ensure that the new Jack is working OK

  Although I'm not a guru in network cabling. But I'm not computer (using Windows & Linux) and I'm quite a handyman. I can't possibly screw up Assembly of ALL taken without tool, I've had. And the misconfiguration of the network in the operationg system is out of the question. Added to this fact that the new tool WITH jack is much easier to mount and all prectly work on the first attempt. I would say in conclusion that WITHOUT TOOL, CLAMP in Ethernet JACKS are UNSTABLE. At least that's my experience.

  It's pretty frustrating, that Jack is the last place I guess as a cause of a wiring problem. I changed to RJ-45 Sockets, wiring maps network and same router. All this has not solved until one day I discovered by chance that the cause was the wall outlet. (New computer loan with Ubuntu, I forgot to reduce the network speed to 10 Mb and directly connected to the switch without going through the wall socket and discovered that the computer can connect immediately to 100 MB).

  Hope this might help someone else.

• Satellite A210 - 15K: webcam problem - graphics make it fail

  Hello

  I have a toshiba A210 - 15K, but I seem to have a problem with the integrated webcam for laptops. When I turn it on I can use it without problems all the time, but sometimes after a few hours of no use when I try to use it again it gives me the following message: "chart make fail" and it runs at all.

  In order to make it work again I have to restart the computer, and even if I restart sometimes it does not start.

  Someone knows how to fix this?

  Thank you

  I noticed the same thing on my Satellite P200. After reboot, everything works again. I don't use a webcam so often and it is not so important to me, but you can try to stop (exit) web cam software and start it again.

  Maybe this will help. Can you please send the result? Right now my cam works well and I can't wait to check this option only.

• problem image acquisition

  Hello

  I try to read my camera webcam images

  I install the visision software machine

  but this problem appear which lies in the acquisition of the vision

  No inilization apeaer menu after add it on the front

  I click on it but nothing happens

  Oh God, what is this

  Hi Mangood,

  I took some screenshots of the process step by step to configure the Vision Acquisition Express VI.

  When you first place the Vision Acquisition Express VI on your drawing, LabVIEW should pause for a moment and bring up a message saying 'initializing Vision Acquisition '.... »

  

  After that, the configuration for the express VI window opens, and you can select your camera. In addition, you can use the Snap and Grab (circled above) as an example of the selected camera image. When you have selected your camera, you can then hit the next button.

  

  On the next screen of the configuration window, you will be able to select what kind of acquisition and processing in your program. This will depend on your application, so read on options and choose any what works for you, and then click Next.

  

  On the next screen of the configuration window, you have the options to change the various attributes of the camera and the acquisition. This is all dependent on your camera and your request, so you can adjust these according to the needs. The default values are often very well without any adjustment.

  

  The last screen of the configuration window allows you to specify the inputs and outputs of the express VI. Depending on the options you chose, you can have more options for inputs and outputs, but the most important of them is the required output 'exit from the Image. It's the indicator that allows to display the image that you have acquired. Once you are happy with the inputs and outputs, you can click the Finish button.

  

  Once you press the finish, LabVIEW will once again take a break and spend some time configuring the Vision Acquisition Express VI with the settings you specified. After it's done, you should be presented with a diagram like the one below:

  

  I hope this helps!

• Rash, the problems of computer control: use of 100% of the CPU, hard drive is filled Up, & drivers Drop Off - what happens?

  My computer keep meeting the same types of problems faced by systems of many other people. My CPU goes to 100% use when I'm streaming a video. No matter if I use the Flash or HTML 5 player, the problem persists, my hard drive fills up, and now my Intel (r) 82801 PCI Bridge - 2448 driver is down, what happens?  I come on this forum and find others looking for answers to problems of the same nature. I don't know any of these people, but we are the same kind of problems. The only link I know that we have is 'Internet '. I don't know if it's a virus or some other bad online. Anyone with computer knowledge can see another link that can be the cause of these problems? It would be a good start to solve these problems. Obviously, something is happening or something happening around these problems.  Tips on how to find a common point or a fix would be much appreciated.

  In order to diagnose your problem, we need run Windows performance toolkit, the instructions that are in this wiki

  If you have any questions do not hesitate to ask
  
  
  Please run the trace when you encounter the problem

• Personal media player problem - Windows delayed write failed

  I have a 1 TB Personal Media Drive (hd10000x) which does not with my e9120f machine Pavilion Elite running Windows 7.  When I try to write to the disk using the dedicated Bay or USB connection, he wrote a small number of files (anywhere from 8-100), then an error "the system cannot find the specified file.  In Event Viewer-Windows Logs------system I get thousands of warnings "an error was detected on device \Device\Harddisk6\DR6" and "the system does not have empty data in the transaction log.»  Corruption may occur.

  This is my second personal media player, I had the same problem with the first, and he returned after spending 90 minutes online with the help of HP trying to diagnose the problem (with a friendly assistance technician yet not very knowledgable).  Its best estimate was Norton AntiVirus, but the drive did not work when the machine has been started in Mode safe and AntiVirus software has not loaded.

  The drive works fine with my old Dell laptop Windows XP, but not with my brand new HP desktop computer.  I think that it must be a driver conflict but can't find anything in the forums or elsewhere online.

  Ideas anyone?

  .

  Who seems to have done the trick - thanks

• Problem with preloader has failed on nextFrame();

  The preloader, I created only the transition to the next section, it crashes just on the chassis of the preloader to 0%.  Here is my code:

  Stop();

  loaderInfo.addEventListener (ProgressEvent.PROGRESS, updatePreloader);

  function updatePreloader (evtObj:ProgressEvent): void {}
  
  var p: Number = Math.floor((evtObj.bytesLoaded*100)/evtObj.bytesTotal);
  preloader_bar. Width = (% / 100) * 600;
  preloader_txt. Text = "Loading" + percent + "%";
  
  If (p == 100) {}
  nextFrame();
  this.removeEventListener (ProgressEvent.PROGRESS, updatePreloader);
  }
  }

  The problem is when the swf file is called online, it stops on the 1st image and shows the preloader to 0% and does nothing.  I can right click on the embedded flash swf nonfunctional and select read and it works very well. but it makes no sense for my users to do the same thing...  However, when the file is recalled after the first attempt it works very well.  Any ideas what could happen?

  :

  {if(this.framesLoaded==This.totalFrames)}
  nextFrame();
  } else {}
  loaderInfo.addEventListener (ProgressEvent.PROGRESS, updatePreloader);
  }

• Satellite A200 - problem WebCam - webcam readers failed

  Hello

  I need help with the webcam integrated my A200 Satellite.

  Whenever I start the laptop that I got a message saying that readers of the webcam does not and I have to restart the computer, but the problem persists.

  I downloaded a update webcam driver, but nothing.

  Can someone give me an idea of what's going on?

  Thank you!

  Hello

  Are you using the OS preinstalled Toshiba? Is it Vista or Win XP?
  AFAIK that Vista needs Sp1 and other updates MS in order to manage drivers and 3rd software part correctly.

  I have internal webcam and I m using Vista and Win XP.
  I deleted the software for the webcam to start in msconfig.
  This prevents the webcam of the automatic start during windows startup
  You should do it too

• Problem of CPU for the 90-100% svchost.exe

  When I bring my task manager, I see that svchost.exe has a really high CPU usage, it just started a few days ago and im not sure what is wrong. I tried updates automatic disableing and also I remember having the same problem with an older computer of mine, but I thought that I fixed it with the installation of an update for Windows XP (KB927891) called update can be found here http://www.microsoft.com/downloads/details.aspx?familyid=7A81B0CD-A0B9-497E-8A89-404327772E5A&displaylang=en

  I tried to install it but it tells me a new package system is already on it and there is no reason for this update. Does anyone know how to fix this?

  This problem is common for the windows operating system. I hope that this source will help you - http://fileinspect.com/fileinfo/svchost-exe/

• Printer problems - HP 5150 printer fails to print

  Do not know if the right forum but here goes have HP 5150 printer.  I continually fail to print and have to close and restart the computer.  Any ideas?

  Do not know if the right forum but here goes have HP 5150 printer.  I continually fail to print and have to close and restart the computer.  Any ideas?

  I guess you're talking about, that you have a ( with the HP Deskjet 5150 color inkjet printer<-- that="" is="" a="" hyperlink,="" click="" on="" it="" and="" select="" windows="" xp="" from="" the="">

  Download and save the file from here (full software and driver)

  Download and save the file from here (updated)

  Reset.  Run the first Installer downloaded and get it fully installed.  Reset.  Run the second installer downloaded and get it fully installed.  Reset.

  See if that helps any.

  (The printer and driver are obviously old enough - no matter where you bought it.)  December 2003 is the last driver.)