problems of thresholding

Similar Questions

• OEM 12 c Cloud Control: two agents on the same host.

  Hello

  I'm migrating to OEM 12 c (12.1.0.3.5). I built a completely new and repository management and the plan is to move a selection of objectives to this new SGO of the old system.

  On a target is host (Redhat Linux 6) possible to install a second agent configured to load on the new OMS, while leaving the original agent facing up and running? It would be only temporary, and the original agent would stop after the target had been discovered and configured in the new OMS.

  Is it possible to run two agents simultaneously on a single host?

  Thank you

  It is not recommended to run 2 versions of EM agents for a period of time, but it is possible.  Things to monitor and test:

  • port must be unique - if 11g use 3872, so you'll need to choose something else for 12 c
  • installation location must be unique
  • DB generated alerts (for example the tablespace) are actually stored in the Pb, then there may be an inconsistency between the 2 and the db if you start to change the thresholds, while the two officers are on the rise and running

  Yet once, it is not recommended as a best practice because of the problems of threshold, so plan to 11 g stop agent as soon as possible.

• I am facing a problem with the beep.vi. I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound.

  I am facing a problem with the beep.vi.  I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound. Everything works fine except the sound alarm. It gives the table 1 d of type mismatch. I tried to fix this by placing it in a box structure. But it still does not work. If someone could help? Please find attached my VI. Best wishes to all visitors to the Forums of Discussion OR.

  Ihab El-Sayed

  published here: http://forums.ni.com/t5/LabVIEW/Playing-sound-based-on-exceeding-a-threshold-value-1D-array-data/m-p...

• Thresholding of image problem

  Hello

  I'm working on a labview of complex image processing program, and I'm stacked.

  I am trying to build a new program structure where all data, inculding the camera images, through a cluster shared between the VI-s.

  In the pictures below you can see the vi treatment Gets the data through the Camera.Image in an another VI, where the snap is taken.

  In this VI I'm doing a photo analizer algorithm, which is used to work earlier, before using this particular architecture. He was not to use a new reference for each stage of image processing, but here I can't do otherwise.

  Until the VI BCGLookup program goes without any problems, the images in the front panel also seem to agree. After adding another VI, IMAQ threshold VI I can't receive any useful image more, regardless of the type of reference I am using.

  The question is how can I make the block threshold to work?

  Thanks in advance.

  See you soon,.

  Dan

  Do you know how thresholding works?

  -After the thresholding the image becomes binary and therefore change the type of binary Image indicator 3 palette.

  -In front panel, click the flag Image 3-> right click-> palette select binary.

• threshold problem

  Hello

  I try to make a thresuld of the isolated object, but I have problem

  After doing a threshuld the picture will be black all time what is important what is the value of throsuld

  I first read image aqusition then convert the gray then filter by use laplicaion then take a

  threshuld object separte value

  I read image of continuos aqusition of usb camera

  any help

  Best regards

  Hello

  Right-click on the display of your image and select the binary palette.

  Concerning

• Problem of VGA Z30 ports - has satellite

  Hello

  I have a problem with my VGA port and would be very happy if someone could help me.

  It used to work when fine connected projectors for teaching, but recently, I have a lot of problems. Initially, the projector is recognized and seems to work fine, but then the connection goes between active and disabled, so the image constantly disappears. At some point the laptop restarts. The is happening on several projectors with several cables.

  I don't think that it's a hardware problem, and I think that has happened since the threshold of 10 last update Windows or windows update automatically to update the video drivers in January.

  Does anyone have any ideas? Which video drivers you have installed the Windows 10 and how to prevent it update without telling me.

  Thank you very much.

  Hello

  The factory driver my not be compatible with the update of TH2.

  Go to settings-> Apps and uninstall the Intel display driver.
  Then let the last Intel display driver Windows Installer update.

• After the last update Windows 10 - Z30 Satellite screen problem - has

  Hello

  After updating Windows 10 (threshold/1115) one of our Z30 - A sometimes wakes up after hibernation with the screen off. The only solution is to turn it off by holding the power and then turning it back on, button which is obviously annoying because open files may be lost or corrupted. The other Z30 - A that you don't show the behavior of sound.

  Someone at - it ideas? I would really appreciate the pointers.

  Thank you very much!

  Kind regards!

  Sounds like a driver problem.

  go to control panel and uninstall different drivers (sound, display, wireless, etc.), then let Windows update install the latest versions.

• When using Firefox I get popups frequent AVG Antivirus saying that Firefox uses an excessive amount of memory - is this a problem with Firefox or AVG or something else?

  Using Windows 7 with all updates. Computer has 6 GB of ram and has no problems with other sites

  If these messages back, see AVG support on how to increase the threshold trigger the trigger for this message. With 6 GB of RAM, there is no reason for Firefox using less than 10% of your RAM to be a problem and cause this message appears. IMO, the alarm should not trigger up to about 50%.

• Problems of excessive noise and fan performance.

  (I found a few similar posts, none seem to have any kind of resolution. I already submitted details to the comments for OS - X and MacBook Pro, because I know that Apple doesn't really care these forums.)

  I'm computer LITERATE in a company with more than 40 Macs. Most are 15 "and 13" MacBook Pro retinas, with some older MacBook Pro, MacBook Air and Mac mini. Almost all have had many problems of performance and especially complaints relating to noise fan since the upgrade to El Capitan.

  All Macs seem to rotate at about twice their original fan speed, even at idle with nothing else running in the foreground. If something - it is actually worse with time and not better. Some of them seem to be entering a mode "overheating" and the limitation of the CPU frequently, even with no real warning to the user. We receive complaints from fans go "full throttle" and not something unusual applications of grinding to a halt, while the activity monitor recount. Even these days - I'm writing this, my MacBook Pro runs only Safari and mail and fans just 15 "kicking until probably at 80% for no apparent reason. The CPU load is only about 8% currently according to activity monitor.

  The usual "fix" to a SMC reset and a clean install of the operating system seems to have no effect. We spent a lot of time in recent weeks reset wiping of Macs to try to resolve these problems. They are located on machines that have been almost completely unless they were actually under heavy load (such as virtual computers running or doing graphics/video editing), with the only change being an 'upgrade' to El Capitan.

  New - the same questions and complaints are reported in almost all of our Macs. I noticed similar problems on my MBP of House. I have a Mac Mini in my office who spends just Safari to view a network monitor page. It used to be silent and cycles now the fan and turns off often.

  At least while taking into account what is actually run on them, as well as information from the activity monitor, it does not appear that the CPU is overheating. It seems that something has gone wrong with the heat in recent management, as El Capitan assign a lower threshold than before well. I am everything to keep these systems cool, especially since Mbit/s in particular seem to run pretty hot anyway, but when the noise of the fans like a small jet taking off-it is a problem for many people.

  If anyone has found a solution to this, I'd love to hear it. Otherwise - if you are having similar problems - please send to Apple Feedback then perhaps they will at least look at or respond.

  If you run any antivirus Mac remove the system. A 3rd party cleaning or maintenance or utility network, any 3rd party firewall they are infamous resource pigs and Mac AV is responsible for a good part of mac OS that any other type of software while offering no protection against anything like that.

  systems running 10.11 with 4 GB of RAM or less will spend a good amount of time cached and if this is the case look into upgrading your RAM, if it's an option.

  If this isn't the case reset the SMC (which you did) followed by a PRAM reset as outline in this paper.

  Reset the management system (SCM) controller on your Mac - Apple Support

• MainStage 3.2.3 CPU problem unsolved

  Please see the video: https://youtu.be/_cpVa64tmrY

  cpu problem in the mainstage 3.2.3

  the video has been used in the same concert, perform the same functions, the difference is absurd.

  Yes, I see this same thing going MS 3.1.1 3.2.x. It was not a 3.2 version that works for more than 25 minutes without serious crackling and stuttering with a concert that I use all the time with absolutely no problem for hours overnight with 3.1.1.

  I spent days trying to track down the issue. I use a lot of 3rd party software, but I have not been able to isolate an offender. If I use a sheet of Apple in the only project, everything works fine. But, my usual concert uses a lot more memory and some of the plug-ins are much more intensive CPU. I'm starting to wonder if there is a threshold of memory and use CPU causing instability in point 3.2. Unfortunately, it seems almost impossible to load enough instruments EXES to get closer to the memory usage that I use regularly with my native instrument patches, so if my threshold theory is correct, I did not spent yet. At the moment, I'm so tired to lose time trying to locate the problem, I'm pretty well reconciled with the use 3.1.1. It's very frustrating, yet. There is no doubt that something fundamental has changed, but it does not have an impact on a large number of people. I'm afraid that those of us with these problems are on our own until we can come up with something concrete to show Apple so that they can remedy.

  So, I'm curious to know what operating system you are using and whether you use 3rd party plug-ins. In your video, I see that you do not use a lot of memory, makes me think that I'm wrong about the memory being an issue. Anyway, if we can find things that are common to our configurations, maybe this will help point to the problem.

• Win 10 "threshold 2' very strong use of the processor by process"system and compressed memory.

  I did a clean install of Windows 10 threshold 2 (aka version 1511) on my MBP 15 "2015 and I encountered a problem. Well two actually:

  1. installing the Realtek driver hangs when you install the software in support of BC. This is easily fixed by killing the process RealtekSetup.exe.

  2. the process of "system memory and compressed" now use constantly one of the eight nuclei which ruins the life of the battery. I had to actually change the power management in Windows to allow the CPU to only go to the maximum frequency of 60%.

  Some research on Google, I have gathered many suffer from this problem on other brands and it is usually linked to a bad driver. I was not able to find the culprit yet unfortunately.

  Now, here's my question: did someone suffering from this issue as well and if so, where you be able to solve it?

  Thank you!

  Try / sleep or hibernation.

• What is the problem with flight mode, by pretending to be on?

  We have several Yogas Thinkpad Windows 10 X 1, who (commentary on the https://forums.lenovo.com/t5/ThinkPad-X-Series-Laptops/X1-Carbon-and-Sierra-EM7345-problem-with-Mobi...) wireless connectivity problems, but this post is related to airplane mode.

  Our devices show the airplane as mode 'ON' in the 10 Windows Action Center, but the 'OFF' in the Windows 10 network and Internet settings. Wireless and mobile phones will continue to work, but the airplane mode button is always blue (see the attached screenshot).

  We have updated our wireless drivers and this problem still exists, what is happening here?

  AE_Support,

  Thank you for sharing your experience with different designs of airplane Mode in 10 Windows Action Center and 10 Windows network settings and Internet.

  This is a known limitation of Windows 10 threshold 2 v1511 and has been resolved in Windows 10 Redstone 1 released by Microsoft in August.

  Thank you

• Thresholds of battery on X 240 Arch Linux

  I recently installed Arch on my X 240 and I was able to solve most of my problems by myself (and with the help of the wiki).

  Now, I tried to change the thresholds of batteries and since there * 40 laptop I can't use tp_smapi.

  I have installed acpi_call and tlp.

  In/etc/default/tlp I put them in this way:

  # Main / internal battery (values in %)
  
  START_CHARGE_THRESH_BAT0 = 75
  
  STOP_CHARGE_THRESH_BAT0 = 90
  
  # Ultrabay / Slice / replaceable battery (values in %)
  
  START_CHARGE_THRESH_BAT1 = 75
  
  STOP_CHARGE_THRESH_BAT1 = 90

  and tpacpi_bat returns this

  # tpacpi - bat - g 1st & tpacpi-bat - g SP 1 & tpacpi-bat - g 2 ST & tpacpi-bat - g SP 2
  
  75 (percentage)
  
  90 (percentage)
  
  75 (percentage)
  
  90 (percentage)

  But still I can't charge the battery more than 80% (which is the initial threshold. (he oscillates between no load and load with zero power)

  Any ideas?

  
  

• T440P, Windows 7 upgrade to Windows 8.1 with 63% battery charge threshold

  Hello

  I have a T440P

  Until recently, I was in Windows 7 with Lenovo Power Manager set of limited to 63% support threshold
  So far so good.

  Now, Windows 8.1 has been installed from scratch (not an upgrade).

  The laptop with windows 8.1 always stop loading at 63%. But there is no available for windows 8.1 Lenovo Power Manager. I can't find any solution to disable this limitation...

  Help, please

  Regarding

  Alain

  Hi Amemo06,

  Welcome to Lenovo Community!

  According to the request, we understand that you are facing problem with the battery not charging more than 63% on your ThinkPad T440p.

  Download and install Lenovo implementation of store Windows, and then follow the link to get help on the troubleshooting steps below.

  http://forums.Lenovo.com/T5/T400-T500-and-newer-T-series/ThinkPad-battery-won-t-charge-past-50-under...

  I hope this helps!

  Best regards

  Agnes Kumar

• ElitePad 1000 G2: 10 Pro Version 1511, threshold 2 update Windows crashes on 'features and drivers '.

  Summer running Windows 10 Pro 64-bit for months without problem on my G2 ElitePad 1000; application Windows 10 updates throughout - so far. Yesterday, 12/11/2015, 1511 (threshold 2) updated version of Microsoft automatically downloaded and rebooted to start installation of operating system upgrade. The upgrade completed the first phase "Copying files" and began the second phase "Patterns and drivers", then stopped (paused) to 40% total progress/23% features and drivers progress with no other response. Only one stop 'hard' (hold down the power button / stop for at least 10 seconds) worked. On 'power up' the result was a "restore previous version" immediately, and subsequent reboot restored my previous login - as expected.

  HP have a new image or update for Windows Pro 64 - bit version 1511/threshold 10 2? The update is put on hold due to a driver issue? Any advice would be appreciated.

  Finally, a solution for me! I used Microsoft's latest "MediaCreationTool" (as of 11/13/2015) to download and create a "USB stick" (08/01/2016) upgrade support. Stick created USB contained more than 3 GB of content upgrade. Started my ElitePad in my 10 original Windows operating system upgrade, and then insert the USB in my ElitePad. Launched "Setup.exe" on the USB key to start the process to level, and left the USB connected until the upgrade is completed; several reboots of the upgrade. Once launched from Setup.exe, a menu background blue proceeded and displays "Check updates" for more than 15 minutes (check the updated drivers, etc.), and then proceeded to the display of the upgrade process (progress circle GUI). The upgrade has completed in 90 minutes without a hitch. So far, all programs and functions are intact. I guess that is focused on the HP drivers updated (finally) in the current construction of 1511, and/or the last created USB stick media works where Microsoft Update (via Microsoft Update servers) has a problem. For me, this solves my problem to upgrade v1511. I hope this helps others.