ProBook 4330 s: logos of laptop but does not start

Similar Questions

• Put 8g memory in es1-512 but does not start. Had to put 4g in. Does anyone else have this problem?

  Put 8g memory in ES1-512 but does not start. Card say that it will accept up to 8 GB. He went out, re he sat several times without success. Does anyone else have this problem? Thanks in advance.

  Hello

  Here's the original memory stick for Aspire ES1-512:

  KN.8GB07.013

  SODIMM.8GB.DDR3L - 1600.KINGSTON

  OR

  Compatible memory: Kingston

• HP pavilion laptop computer does not start

  When I turn on my laptop it does not start. It goes to a blue screen that indicates it should be repaired. Help please

  Hello

  Error code 24 characters long drive Self Test (DST) would indicate that hard is defective and must be replaced.  This is also consistent with the startup problem you describe.

  If your laptop is still under warranty, contact HP and arrange for the disk replaced - you can check the status of your warranty here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.

  Kind regards

  DP - K

• PC runs, but does not start. Monitor, keyboard and mouse with no signal.

  PC runs, but does not start. Monitor, keyboard and mouse with no signal. Pretty much. And when you want me to remove the battery of the bios, or whatever, it seems tight and hard to get out because it is surrounded by other elements.

  All fans work, the power/battery or anything that works I think that, since there is a fan on the right where it is and it seems to work. I remember what happens before, I don't know, but before that, there are many gels. This error below was made before all this happened, but I managed to run f8 and then run normally until it freezes again. Then, after that, it runs but does not start. No beeps etc. The best fans will have plenty of vouches and Bravo to wherever you like me to vouch or maybe send the great service that you provide to administrators if that's even possible, haha.

  Thanks in advance.

  "

  The file is possibly corrupted. The file header checksum does not match the checksum calculated. »

  It is a sign of a lack of food.  Looks like you have a desktop computer?

  Power supplies run about $50.  It is a rectangular box at the corner of the system in which the power supply will from the outside.  It's a pretty standard form in most of the PC and with a little investigation thorough replacements can be found.

  It is usually held in place by 4 screws and can be held in place with a spring clip.

  Most essential, is that you need to buy a replacement with the right number of straight plug forms to adapt to your PC.

  This seems more complicated than it really is and takes about 5 to 10 minutes to do the replacement.

  Look at the power output of the power supply failure and buy a new, more powerful.  New desktop PC usually come usually with a diet under size and what are the causes these failures is too strong a request for devices you have connected.  So, buy one with a higher power rating.  Usually about 500 Watts does the trick.

  If you do not feel upwards to this task, a technician should not charge you much like this.

• Recovery partition is there but does not start Recovery

  Hello
  
  When you try to restore the image (F11 at startup), the laptop seems to be as he tries to start missing Windows installation (Windows Boot Manager error page).
  
  Partitions 'SYSTEM', 'HP_RECOVERY' and 'HP_TOOLS' have not been affected. Recovery files of ~ 15 GB are still there!
  
  The Windows (2nd primary) partition was deleted and then recreated as an NTFS partition. Since then, the recovery process does not start.

  How can I restore my intact HP_RECOVERY partition system without using recovery DVD? (I can't access right now.)
  
  The partition Windows has need of a specific disk label? What is the magic that breaks the recovery when an NTFS partition is all simply deleted and then re-created?
  
  Peter

  HP ProBook 6550 b (WD701EA #ABD)

  Solution: How to fix F11 penetrates is not in the Recovery Manager process

  You will need:

  -This fix by HP: difficulty to the Multi-partition HP Recovery Manager (the ProBook 6550 b is not listed as a supported model, but it worked for me)

  -installation of Windows (see partial solution above) a job to install the fix on your ProBook

  or

  -sufficient knowledge to extract the winre.wim missing the fix above, copy it to your recovery partition and to apply any measures necessary (I did this)

  Steps to follow:

  -in your work on your ProBook Windows installation open the file downloaded "sp48415.exe".

  -the files will be extracted in "C:\swsetup\SP48415", open this folder in Explorer

  -Right click on "F11SPFix.cmd" and run as administrator

  -the patch will be applied

  Restart und press F11 at startup to enter your recovery Manager (hopefully) fixed.

  Credits to HP support.

• Pavilion dv7: my Pavilion Dv7 laptop computer does not start the system recovery options

  So it told me to turn my phone off, then back on whilist cling the key F11. But when I do it my is laptop beep loud noise and rest on the logo hp, whilist is on this screen is says 'System recovery F11' in the lower left corner and does not move on the screen, how to fix this?

  Hi @Jaytee2 ,

  Thank you for visiting the Forums HP's Support and welcome. I read on your HP laptop and get a blank screen or black at startup. Try perform a reset.

  When you perform a hard reset note remove all USB devices. Disconnect all non-essential devices.

  Here is a linkto computer does not start for Windows 7.
  
  Here is a documentthe performance of a Windows 7 system recovery.

  Do you have records system for this laptop?

  I'd be happy to help you if necessary. How can I find my model number or product number?

  Please let me know.
  
  Thank you.

• Satellite A300 - rotates but does not start

  Hello

  I have a Satellite A300. I had several probems for the boot since 2 months ago: when I want to turn on my laptop, it turns on but the screen keeps black and it does not load the screen "Toshiba Leading Innovation". 'Satellite' (to the left of the mouse) light is on (it would go only about a second then to start and then turn off) and it will turn off.

  I try again for so many times with all the possibilities: without battery, only with the power adapter, two, but it does not start. I don't know what I can do. I always Hibernate my laptop because I'm afraid of can not start it the next day.

  Could you help me? If she cares: I had to buy a new battery (not original from Toshiba) because I had to change the original. No more changes to my laptop.

  Thank you very much and sorry for my English written: S

  Diego

  Hey Buddy,

  > I had to buy a new battery (not original from Toshiba) because I had to change the original. No more changes to my laptop.
  Of course, it s always advisable using Toshiba original spare parts only, but if you notice the same problem with AC adapter only it s not related to the new battery.

  Just to make a better diagnosis: If you have connected an external monitor? The internal display is perhaps the problem and doesn't turn on and it would be useful if you are testing the situation and an external monitor.

  But this noise as a hardware problem serious and in this case, you can wait to contact an authorized service provider. Technicians professional diagnostic tools to make an accurate diagnosis and to Exchange defective equipment parts.

• 15-p151nr Pavilion: Pavilion 15-p151nr dead, power supply LED flashes 3 times but does not start

  With or without the adapter is connected to the computer (well known socket), the computer will not turn on.  The LED located on the left side of the computer where the socket is attached blinks 3 times (white), but does not supply power to the top.  Another post I saw said "continuous" flashing would be the power adapter, but wanted to ensure that it is in fact the problem before buying a new...  Any help would be great!

  Hi @joshuaj21,

  Welcome to the HP Forum!

  It's a great place to find answers and advice! You have the best experience in the HP forum, I would like to draw your attention to the Guide of the HP Forums: first time here? Learn how to publish and more

  I understand that the computer will not turn on. However, when you connect the AC adapter of the power port light flashes 3 times.  Please check that the power cord is not one of the recall. HP laptop AC Power Cord Safety retirement program and replacement announced August 26, 2014 .  You use a power bar?  Have you tried a different outlet? Here is a link to the HP laptops - tests and using the AC adapter which can also help.

  Please let me know the results.

  Thank you! If it helps you to find a solution, please click the button "accept as Solution"down below in this message. "If you want to say 'Thank you' to my effort to help, click on the" ""Twww.Mountainview.rsb.qc.ca Up ' give me a Kudos. : catvery-happy

• Portege R100 laptop computer does not start after a while without food

  Hello

  Well there is some time, I bought a beautiful used R100 - a laptop Toshiba in passing - but now, she has developed an annoying problem. Whenever it disconnect the laptop from the power supply for more than 2 hours about (don't know if this is not longer) I can't begin the R100, even if the battery indicator is green. After pressing the powerbutton the power led lights in green, and nothing happens. The "solution" to this problem is to give the R100 some time in this 'turned on' - State and after 15 minutes, I am able to start the computer (turn market again).

  I think that this could be a problem with a battery on the motherboard that is at its limits and needs time to gather enough power to start the computer.

  I hope you can help me identify the problem with my beloved laptop :)

  Yours,

  Tobias

  p.s. I have more or less need to identify the problem and some tips how to solve - the pleasure with the surgery will be from me :)

  p.p.s. Unlike the problem of the M400 further down, I've won if the beginning focused on the hard disk to Flash. In my case the R100 does not give a glance if it does not start. - And as a reference to the other post: "Hmm, I don't remember of the R100 fan not have it at all" * huggs its r100 * "."
  And I tried unplugging all the bits of the laptop and removed the battery, waited 15 minutes and tried to turn it on. the only way to obtain the departure of r100 is the method described above.

  You have an additional RAM installed?

  Maybe you need to re-seat, or it has a intermittent or heat associated with problem.

• Mini laptop of HP 1000: mini windows laptop computer does not start

  My mini laptop from HP is saying windows has not start because the following file is missing or damaged:
  \windows\system32\config\system
  You can try to repay this file by starting windows setup installation CD using the original.

  Hi there @kgoen81

  Welcome to the Forums of HP Support! It's a good place to find the help you need, so many other users, the HP experts and other members of the support staff.

  I understand that you receive a message from a missing file, and that your system does not start. I'm happy to help you.

  First, I recommend that make you an external backup of data on the hard drive. There are several ways you can try to do that, but here is a page with a few possibilities:

  How to recover data from the hard drive to a laptop dead - eHow.com

  Also, please post the complete product and the operating system running on your laptop. Check out the following, if you need assistance with this information.
  How can I find my model number or product number?
  Is the Version of Windows on my computer 32-bit or 64-bit?

  For now I'll assume you have windows 8.

  Computer won't start (Windows 8)

  You can also visit this page, and in particular you want to go with the automatic repair options. I would try before using a full system recovery to an original image, on the previous page I linked.

  System - Boot of Windows 8 recovery options - eightforums.com

  I hope this helps.

• Touchsmarrt Tx2 turns on but does not start.

  The laptop turns on I hear the fan, the caps lock and a lock of numbers blink, but it does not start. I'm runnin windows 7

  Home premium. I did recent changes. Just put computer in mode 'sleep' and he won't wake up. The wireless light is orange.

  Electrical components sometimes must have all the food sources removed and reintroduced to work properly.  Try to perform a hard reset first, if this does not work then we will move on to the next step.

  To perform a hard reset

  • Shut down the computer by going to the menu start and select shut down. (If you have no display, hold the button for 5 seconds); (if the computer don't market, go to the next step)
  • Unplug the adapter from the laptop.
  • Remove the battery from the bottom of the laptop.  There will be a switch/battery eject button.
  • Wait at least 1 minute with all sources of power disconnected.
  • Reinsert the battery and reconnect the power adapter, and then try to turn on the laptop.

• Pavilion 15 - p002nia: HP Pavilion 15 - p002nia fan runs but does not start

  My 2 year old son poured drink chocolate on the keyboard of my laptop 15 - HP Pavilion p002nia recently bought. When I found out, the laptop had stop, all efforts to start failed. White LED light on the button walk / stop would stay and fan would run for 30 seconds, stops, starts and stops continuously. The system does not start. What can I do? The jury is dead?

  Hi TheOldMan, thanks for your response. But, someone suggested I have dismantle the system, clean with alcohol and dry that it might help the dos system.

• MacBook Pro-life extendable start-up chime, but does not start

  I have a start 2011 15 "MBPro8, 2

  Quad Core Intel Core i7

  2.30 GHz

  Boot ROM version: MBP81.88Z.0047.B2A.1506082204

  Intel HD Graphics 3000 VRAM:512 MB

  AMD Radeon HD 6750M VRAM:1 GB

  8 GB of RAM 1333 MHz DIMM0

  It will not start.  Trying to start the machine, it enters a loop-

  1. startup chime

  2. grey screen with Apple

  3. the small wheel starts to turn under the Apple

  4. the screen goes black

  ... and the cycle starts over.

  The computer does not start in Mode safe.  In an attempt to safe mode the loop above has the addition:

  3. a progress bar is displayed but does not progress.

  I have reset the PRAM

  It will start up in target Mode, so I was able to recover data

  In target Mode, I was able to run first aid utility on the drive.  This has not fixed the problem.

  I can hold down the Option key and see Macintosh HD and the recovery Partition.  If I try to boot from the recovery partition, I get the same loop.

  I can start in the Test of online material, which revealed no material problems

  I can boot in Verbose mode and it always happens in the same place

  Execution fsck_hfs (version 226.1.1 of hfs)

  BootCacheControl: cannot open /var/db/BootCache.playlist: 2 no such file or directory

  ' ' It would be possible for me to insert the "var/db/BootCache.playlist" file using target disk mode?

  Other thoughts?

  Have you tried resetting the SMC?

  Reset the management system (SCM) controller on your Mac - Apple Support

• Pavilion dv7-6101eo works but does not start.

  My laptop got a cup of black coffee on the keyboard.

  I have cleaned up a bit, disassemble the entire laptop, same cpu, added new money and put the brand new togeather. Started and everything worked. Close the computer laptop domw - dead. Could not start without flashing, nothing. Repeated picking hand everythung once again and began. Works perfekt press start and go. So this time I made a recovery and reinstalled everything.
  
  The keyboard does not everywhere, a, s, d, f, e, l and Swedish letter o does not work very well. I don't have much contact for helmet properly not work either - you get a bit of his, but a little in the speakers and phones. I forgot to check the sd card reader, but here, it is located in the corner of a speaker.
  
  Onece I disassembled except mobo and this card reader and then the laptop is not started. I had to do it all again and he began. So now I'm a little confused to what it can be?
  
  It does not remove batteri, pushing start button. Not 15 seconds - not even 2 minutes. I know that battery, power cord works fine, cd, network, hard drive, memory, fan, cpu - everything works and yesterday the laptop running 24 hours without dysfunction at all. Programs installed and revived over and over again. And after all that I closed the laptop the way you should. And - he won't do it again?
  
  There is a possibility that some power is left in the drive cd-card or something that stops the laptop to boot? Or is it enough that the keyboard is malfunctioning? I don't understand what it is with the disassembeling process that makes the laptop to start.
  
  It's not fun to have all take part whenever you want to start your computor ...

  Looks like the coffee did more damage as you thought.

  You should have dismantled it and used contact cleaner everywhere where coffee could go.

  The next step is difficult for most people: allow to dry for at least a day outdoors in a dry place without danger... It is unfortunate that you don't have that.

  Consider looking for a replacement book.  A motherboard and keyboard options, less the cost puts you upside down against the current value of the laptop.

• Satellite A500-148 turns on but does not start

  Hi all, I have a Satellite A500-148 from a friend who asked me to take a peek, it turns on, but does boot when I press the following power button occurs:
  -The power button and the charger are on and the hdd led only flashes once
  -The fan comes on for about 3 seconds
  -No image on the screen, I indicated a light against it, but there is really no image

  Tried to reset by pressing the button for 30 seconds without the changer is plugged.

  I disassembled it and noticed that this laptop has an external video card, so my question is, who's broken the video card or the motherboard.

  Thank you

  To be honest I don't understand this with an external video card. Can you describe how you mean exactly?
  In any case, on this virtual path, it is not easy to offer the exact diagnosis. You can try the little test and remove this external adapter, RAM and HARD disk, and try to start again.

  Ask your friend if he had something that may be responsible for this.

  One last thing: laptop stays in r might have turned off after a certain time?