PTC not reports any resource available on bridge
Hi all
I'm having a strange behavior...
My bridge is a 5320 MCU, a license for the 7 ports in Full HD (14 HD, SD 28, etc.) version 4.5. I'm under XC4.0 PTC with no key to unlock. We have a bridge at this time, if no great reason to have bridges anymore.
We don't use that Conference ad hoc... dial users meeting.
When you arrive at 7 or 8 calls, TPC starts to announce that there are no resources available and calls get a busy signal. I raised the alarm on the bridge up to 100% limit... now I am up to 9 calls to two conferences. PTC reports 93% usage on the MCU, which I know is not the case. Why is it reported this. I have attached a screenshot of the use of PTC and a screenshot of the configuration of the MCU. If it is relevant, most endpoints are SX series (10 or 20), EX90 or Jabber for the customers of telepresence. Any help would be greatly appreciated! You have a single configured waterfall, conductor always reserves to double the number of ports on the cascade that you fixed by the Conference, in the case where she needs, double because she needs a port of the waterfall for the primary and secondary Conference. On the previous image (tpc_ussage), you will have a total of 9 connected participants, as well as 4 ports reserved waterfall (2 per conference). So 9 + 4 = 13 ports used and 14 total ports divided by 93% capacity = 13 ports used. Also, keep in mind with participants by composition of the auto zero, conductor always reserves a port for these types of participants, even if they are not connected, it's in case they later they connect, they will be able to. Tags: Cisco Support Two hp 17-inch workstations mobile (business) Z book 17 On consumer laptops, I can view the files on my external hard drive 1 to and 1 GB player. On these corporate work stations (mobile), I'm not able to view the files on the hard drive or flash drive. I need your help so that I can save files from the internal hard drive of the mobile platform of book z hard disk external. And I need to be able to reconnect the external drives and readers to the Zbook mobile workstation to transfer files to transfer flash. These are the pop ups that appear for each when displaying of readers by opening my computer: When left click hard disk drive a pop up appears with the title bar: location is not available. H:\ is not accessible. Access is denied. Make a right click on the hard drive allows opening of the FreeAgent GoFlex drive (H The tabs are ReadyBoost, previous Versions, Quota, customize, general, tools, hardware, sharing, security By clicking on security of advances and then permissions then continue and then change my name owner or administrator... both methods result in the same access denied result once again. I came across this http://technet.microsoft.com/en-us/library/00d04415-2b2f-422c-b70e-b18ff918c281 is this something I need to study and learn before I am able to connect and use an external drive or flash? Or is there another problem? If the answer is in this link, do I have to put emphasis on and why wasn't windows 7 configured so that it is easy to use external drives as in win xp and win 8? Are all usb ports do not or all drivers of failing or is it a software problem all? I was not able by trial and error to display all files on any hard drive or external flash on the two books of z of mobile workstation. Then I went to the flash drive. Left click on the flash drive produces a pop-up with title bar G:\ You don't have permission to access this folder. Click on continue to get permanent access to this folder. After clicking on continue it opens another pop-up with title bar G:\ You have been denied permission to access this folder. To access this folder, you will need to use the Security tab. When clicking on the Security tab he opens a new pop with the title bar: removable disk (G The tabs are general, tools, hardware, sharing, ReadyBoost, customize He did not indicate what to do next. Summary: Two new computers hp zbook stations mobile work with win 7 pro Or computers with their multiple ports usb allows to access my external hard drive or flash drive. The external hard disk and flash dirve each work very well with the consumer portable computers hp with winning 8 and 8.1 of win and have worked with computers with win xp. How can I get the Replicator hp z book with win 7 pro for usb drives work with external hard drives or external flash drives? I have so far done the following: (1) run administrative guest with sfc/scannow and it found no violations of integrity (2) ran microsoft fixit will be all available Parameters which automatically checked and corrected each book workstation z mobile http://support.microsoft.com/mats/windows_file_and_folder_diag/ (3) contacted HP support (4) checked for malware using microsoft security essentials, malwarebytes and spybot on each mobile workstation (5) updated drivers using HP support assistant on each computer (6) windows update the device HP support assistant on each computer
How do two new computers with win 7 pro can be connected to external drives that allow to view the files as they do with win xp and win 8 automatically? How can I access my files on the external hard disk and flash the mobile workstation book z? The specifications for the mobile workstation of zbook are: Operating system: Windows 7 Professional 64-bit Service Pack 1 Microprocessor: Intel core i7-4800MQ CPU @ 2.7 GHz Moemory system: 16 GB of memory on 2 1600 MHz dimm Graphics device 1: Nvidia Quadro K3100M Graphics device 2: Intel HD 4600 graphics card Hard drive 1: SCSI Disk Device C: 683.42 (613,62 free go-go)
D: 12.21 GB (1,3 GB free) E: 1.99 GB (1.97 GB free) The hard drive is a seagate 1 TB drive that works very well The flash drive is a 1 GB drive which works very well Here is the new mobile workstations HP Z book 17. Microsoft said that HP is responsible for the operation of win 7 in the first year for the operating systems pre-installed HP elite support doesn't know how to solve the problem with the USB ports on the two books of Z is not able to provide access to external hard drives or flash drives These two mobile workstations have problems of USB port with all the ports on each computer? These two mobile workstations have problems of windows 7 where the client has to learn how to use the registry to store external hard drives internal hard drives? What does do to be able to back up files on a disk external hard drive internal? Have to do to be able to use flash dirves with a 17 mobile workstation z book? This problem has been resolved. The book of Z 17 HP installed their software: HP Client Security. This software prevents the use of external hard drives and flash drives in its default settings. Each customer is on their own in discoverinv and the resolution of this problem. There is no warning. He made no information on why a right click on a drive and checking the property do not work. The way in which this issue has been resolved was by a clean boot process in msconfig. When miscrosoft services were hidden items that remained were read. Systematically, some were checked and unchecked, and the computer has rebooted to see if the problem was still in existence or if the problem has disappeared. Whenever the hard drive or flash drive has been verified. We were lucky that we checked to see if it was or not HP software at the beginning. This problem was caused by the default client security HP who were to refuse all USB connections. This consumes a lot of time and was so frustrating. On the first book of HP Z 17 thin client HP security biometric authertication failed with a black screen. The computer is about 15 days old. All the dirvers for the HP notebook have been uploaded and then the software for biometric devices have been downloaded. HP determined that it was a hardware failure of the biometric device, when drivers and software downloads together has not fixed the problem. This computer had / has the same problem with not allowing communication with any external hard drive or flash drive. HP did wrong by not providing any information on the inside of this product the HP support assistant. Here's a consumer might encounter problems:
The HP support assistant on Z book provides updates of drivers for windows, but the support phone number book mobile z is not listed. There is a phone number, but it is a regular support, not z book mobile support or elite support. Mobile Z book users are supposed to call the number fo elite press and the number is for a regular support on the wizard of book z mobile support. Support assistant has cat support method and the HP chat support is not trained to book support z mobile. There is a feature to contact the technical support and the transfer of data to the technician, and again, it goes to regular support who is not trained to support the mobile z book. If you call the phone number provided some of the choices on the automated line includes desktop, laptop and office work. If you choose Notepad you won't get z mobile workstation support. If you choose work center you will get no support of z book mobile workstation. Instead, you must have someone answer and then ask to be redirect to support elite. On the first call, you never know that the support you are looking for is elite support until they give you this information on the next contact. After many hours spent barely pull on the problems of not being able to view files on an external hard drive or external dirve flash, I was able to change this HP software. It now unfortunately produces a humming noise when parts of it are displayed. This has not yet been set. It is the customer of HP security information: There was no information to reconfigure the software in the white paper. I was able to find a user guide.
This guide was not and was not available through the HP support assistant: http://h10032.www1.HP.com/CTG/manual/c02292692.PDF Hope this helps all who are unable to view the files on their external hard drives and external flash drives. The thin client HP security prevents click right change of ownership and prevent changes, right-click in the security, etc.. Change of Director fails also as the client security administrator HP overides too. So end users must change the HP Thin Client Security so that it does not block access to files on external hard drives or flash drives. Original title: complaint of Microsoft Dear team, Please note that we had bought a laptop Lenovo S 405 of Croma store located at Silver Bow Ludhiana. Type of machine:-IdeapadS405APGRTXA84555M4G5008EIN(20196) mode Machine Type No.:-59348194 Serial number of the machine: -.
Laptop provided with the integrated Windows 8 homepage unilingual, we tried to remove formatting the hard drive & then tried to install Windows 8 PRO that was purchased separately, but the system does not work, system displays a message error that says "the product key entered does not match any available window images, please enter a different product key Ask you please help to solve this problem Anticipating a quick answer on the same Thanking you, Yogesh clavreul, + Hi yogesh, This problem could be due to the fact that the product key provided does not match the press which is used to install Windows. The product key that is provided can be a file without assistance, in a. EI. CFG file, in the PID.txt file or in the BIOS firmware. Windows OEM 8 machines ship with the product key in the firmware, and if this product key does not match the press, then you will see the above error message. You are able to start after receiving the error message on the screen? I suggest you to change the product key to the correct for the media you are trying to install. If the system has a product key in the motherboard (o. a. 3.0 [Activation OEM] provides an OEM product key in the firmware), you use an Unattend file, file (EI.cfg) edition Configuration or the product ID file (PID.txt). You can check the link: «Windows 8 or Windows Server 2012 installation may fail with the error message: the product key entered does not match any of the images available for installation Windows.» "Enter a different product key" http://support.Microsoft.com/kb/2796988/en-us For reference, you can check the link and follow the steps proposed by Steven on 24 January 2013: Please let us know if the problem still persists. 2921 isn't enough resources available DSP PRI Hello friends, I m programming PRI with 32 channels, but additional 2921 say 2 DSP are necessary. Please, any idea? Router (config) #controller e1 0/0/0 __________________________________________________________________________________________ Router #show voice dsp group all DSP groups on the slot 1: DSP resources to 0 failed Your cards FXO and profiles of conference are taking up all of the DSP. Chris Not detected SD (import of the bridge photo) Hello What card SD Sandisk Extreme XC I is inserted, I used to import photos from "Get Photos from camera. Once the screen opens, Bridge does not recognize any device. I tried to get information on the forum without the solution (IT): Re (February 11, 2016) Operating system: MAC OSX 10.11.2 (15 c 50). I noticed that the question on this topic, I guess, is certainly a problem of bridge with the new version/optimization. Images can be easily copied and pasted from the SD card in the specific destination folder, but the tool good point of the bridge has been the import of rename package. Concerning Hi all We have released an update for Adobe Bridge (CC 2015) on 19 September 2016. The version number is 6.3.1.186. This update is available via the Adobe Creative Cloud application. Bridge is still a free application. Please try the new construction and are looking for the crash problems you encountered. You may need to update the creative cloud app and restart your computer to see the update patch. Thank you Deepak Gupta I can not open any application - CC 2015 has stopped working. I just bought a business plan for all applications, and I installed on my computer. The problem is that I can not open any application, all the applications to give me the same error: Adobe AE/Photoshop/Illustrator etc. CC 2015 has stopped working. Details of problem: Signature of the problem: Problem event name: APPCRASH Application name: AfterFX CC.exe Application version: 13.7.1.6 Application timestamp: 56da9321 Fault Module name: MSVCR120.dll Fault Module Version: 12.0.21005.1 Timestamp of Module error: 524f83ff Exception code: c000001d Exception offset: 000000000008ca 90 The system version: 6.1.7600.2.0.0.256.1 Locale ID: 1033 Additional information 1: f911 More information 2: f9117f2c8a52791eb11044aaa5172d0e 3 more information: f2ee Additional information 4: f2ee1055445f54ef2caa6c329db054f5 Read our privacy statement online: http://go.microsoft.com/fwlink/?linkid=104288 & clcid = 0 x 0409 If the online privacy statement is not available, please read our offline privacy statement: C:\Windows\system32\en-US\erofflps.txt I searched the web and I tried a number of solutions, none of them worked. What should I do next? Here are my computer specs Windows 7, 64-bit Display: AMD Radeom (TM) R7 370 series CPU: Intel (r) Core i5-4460 CPU @3. 20 GHz, 3198 Mhz Motherboard: Asus All Series Memory: 16 GB DirectX version: DirectX 11 I want to emphasize that I have all the drivers updated, do not report to X update because I have already done. I don't want to be disappointed about my purchase, I really want to feel the power of the CC apps. What's not here? Thank you Hello Razv, I recommend you do a clean install of all the Adobe Creative Cloud applications, to do that please follow the steps below: These changes are temporary you can restore these changes back to normal once your creative cloud application is in place and functioning *. (1) uninstall Creative Cloud Desktop Manager: Using creative cloud | Uninstall the creative cloud desktop application 2) Remove suite of files: ( If you do not see any folder skip this step ) C:\Program Files (x 86) \Common Files\Adobe\OOBE C:\Program Files (x 86) \Common Files\Adobe\Adobe Application Manager C:\Program Files (x 86) \Adobe\creative cloud files
C:\Users\
C:\Program DATA \Adobe\ Rename SL-STORE like SL-STORE_OLD file
3 - Click on the link below and download Creative Cloud Installer file and use them to install the creative Cloud Desktop application. Download Adobe Creative cloud apps | Free trial of Adobe CC Let us know if that helps. Opens a PayPal scam e-mail e-mail link do not enter any info am I okay not jail broken iPad 2 Open a PayPal link for phishing e-mail do not enter any info reported immediately is my iPad okay he wouldn't jail broken it I have to do something else iPads don't get viruses. If you have not entered any information, you are OK. Mid 2011 iMac 27 pink vertical lines and does not start - any ideas? My iMac was working normally when he is suddenly flashed to a Uni blue screen. I rebooted and it came with the normal loading as burt screen with vertical lines of roses. He gets a third of the way through the sequence start then just goes to a gray screen and hangs. I tried Safe thing same boot. Apple Diagnostics ran short and long tests, and comes without any problem. Occasionalyl iMac starts and works for awhile then crashes on a gray screen is unresponsive. Any thoughts on what would be the problem? 6 months out of the AppleCare too! Please make an appointment at the Apple Store - Genius Bar store and bring it into service. If you are in the United States or is unable to make an appointment in this way, contact your Apple store. Question (?) Mark, record of flashing or a gray screen at startup It's related, but not identical questions. Their causes are described in based on Intel Mac-Startup sequence and error codes, symbols. Solutions will be found in: A globe or a flashing question mark appears when you start your Mac Mac OS X - grey appears during startup In most cases problems can be caused by one or more of these: a. problem with the computer's PRAM - see reset the PRAM and NVRAM on your Mac. b. boot, directory of the drive has been corrupted - repair with disk utility. c. critical system files are corrupted or deleted - reinstall OS X. d. the hard drive is physically non-functional - replace the hard drive. Please note that the information I have provided is what Apple recommends, if other users will suggest different solutions found here, then be sure to what they recommend has no impact on your ability to get the Apple continuous service guarantee, if any. Please do not start remove disks or change cables unless you know what you're doing and have exhausted other alternatives non-invasive described here. If you perform all knit yourself which is not approved by Apple, then you will void any warranty you can have and lose any other Apple support. Fix the hard disk and permissions Boot from your Snow Leopard installation disc. After the installer loads, choose your language and click on the button continue. When the menu bar appears select utility drive in the Utilities menu. After that the charges of THE select your entry from hard drive (mfgr. ID and car size) in the list on the left. In the status area, you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is faulty or has failed. (State SMART is not reported on external drives Firewire or USB). If the drive is "verified", then select your OS X volume in the list on the left (subentries under the entry for the road), click the first aid tab, then click the repair disk button. If THE reports any errors that have been corrected, and then run repair disk again until no errors are reported. If no errors are reported, click repair permissions. Wait until the operation is complete, then exit FROM and return to the installer. If THE reports errors, it cannot be resolved, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you do not have one of them or none of them can fix the disc, then you will need to reformat the hard drive and reinstall the OS X. The main difference if you use Lion or Mountain Lion, you must first boot from the boot Recovery HD simply HD recovery to perform the foregoing. Reinstall Snow Leopard without erasing the drive
1 fix the hard disk and permissions
Boot from your Snow Leopard installation disc. After the installer loads, choose your language and click on the button continue. When the menu bar appears select utility drive in the Utilities menu. After that the charges of THE select your entry from hard drive (mfgr. ID and car size) in the list on the left. In the status area, you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is faulty or has failed. (State SMART is not reported on external drives Firewire or USB). If the drive is "verified", then select your OS X volume in the list on the left (subentries under the entry for the road), click the first aid tab, then click the repair disk button. If THE reports any errors that have been corrected, and then run repair disk again until no errors are reported. If no errors are reported, click repair permissions. Wait until the operation is complete, then exit FROM and return to the installer. If THE reports errors, it cannot be resolved, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you do not have one of them or none of them can fix the disc, then you will need to reformat the hard drive and reinstall the OS X. 2 reinstall Snow Leopard If the disc is OK then leave FROM and return to the installer. Proceed to reinstall OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a new copy of Mac OS X, the installer will move your Home folder, third-party applications, elements of support and network preferences in the newly installed system. Download and install Mac OS X 10.6.8 v1.1 updated Combo. Relocation of Lion/Mountain Lion without erasing the drive HD recovery start: , restart the computer and after the buzzer, press on and hold down the COMMAND and R until the menu screen appears. Otherwise, restart the computer and after the buzzer, press on and hold down the OPTION key until the Boot Manager screen. Select the Recovery HD and click on the arrow pointing down. Repair the hard drive and permissions: at startup, select in the main menu disk utility. Repair hard disk and permissions as follows. When the recovery menu appears, select disk utility. After that the charges of THE select your entry from hard drive (mfgr. ID and car size) in the list on the left. In the status area, you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is faulty or has failed. (State SMART is not reported on external drives Firewire or USB). If the drive is "verified", then select your OS X volume in the list on the left (subentries under the entry for the road), click the first aid tab, then click the repair disk button. If THE reports any errors that have been corrected, and then run repair disk again until no errors are reported. If no errors are reported, click repair permissions. Wait until the operation is complete, then exit FROM and return to the main menu. Reinstall/Mountain Lion Lion: Select reinstall/Mountain Lion Lion and click on the button continue. Note : You will need an active Internet connection. I suggest to use Ethernet if possible because it's three times faster than wireless. 2012r2 servers not report to WSUS after installing these updates After the installation of the following list of updates, all three of our 2012r2 (two physical, a virtual) servers have ceased under the WSUS running on a machine 2008r2. Before going through the process of uninstalling each of these updates one at a time, I wanted to see if someone had experienced the same thing. There is no error message about the service update on any of the servers 2012r2. The notification only I see is in the interface WSUS where he said the machines were not reported in since these updates have been installed. The updates have been installed on different days on the machines, but once installed, they stop immediately notification in. Here is the list of updates: The WSUS is version 3.2. The latest updates in 2012r2 came down the pipe to the WSUS server. After being approved, the servers 2012r2 all found new updates from the WSUS server, install them, and the WSUS server relates now that they have all checked. This seems to have been a temporary problem. Backup files Vista - "Windows could not find any backup sets [file path]." I have a Vista computer. The hard drive broke so until I replaced it I backed up all the files on the computer to another computer running Windows 7. I did it in the backup and Restore Center. I made a backup of files, not a full backup of the system (I've seen the full backup of the system mentioned in other posts, but that was not an option... maybe which is only available on Vista Premium). In any case, I replaced the hard drive and then try to restore the files, but I get the message "Windows could not find any backup sets [file path]." Anyone have any ideas? Thank you. Here is an article on the restore procedure:http://www.vista4beginners.com/How-to-restore-files to make sure you do this right. It's a selective restore of a full or selective backup (not a full restore from a full backup) - but since you did a full backup, it matches your process more closely than would a full restore. Here is an article on the advanced use of restoration (during normal restore does not work):http://www.mayankraichura.com/post/2009/08/06/Avdvanced-Restore-via-Windows-Vista-Backup-and-Restore-Center.aspx. Restore files from a backup Back up and restore: frequently asked questions I also found the following (but don't know if it of true or not): 1. after the start of "backup and Restore Center." 2. I chose "Advanced Restore" 3. I was did not an administrator password... maybe because my account is an administrator account. 4 choose "files from a backup made on a different computer. 5. in the dialog box indicating "Select the location of the backup to restore", select "hard drive, CD or DVD...". » 6. under the drop-down list box, select your drive/partition and continue 7. If all the backups on your drive, it will show a list of them. 8. in my case, he showed a backup, but in the backup location, it will show "backup location is not available." 9. I was frustrated, but then I somehow just select this backup (Yes... even if he said that thebackup location is not available " ") 10. and you press "next". 11 guess what... no error! 12. a window appeared asking me if I wanted to do a full restore, or I want to select specific folders or files. 13. I selected the folders I wanted to restore and bingo... it their restored smoothly. 14. so that the next time see a mistake, try to continue with him... ;) I don't know if this will help, but it does not provide much information about the process (when it works). I hope you find any error or discrepancy in your procedure and it will clear up and allow you to restore. I hope this helps. Good luck! Original title: how access key USB secure Windows vista I have a lexar player sure to jump that I used with an old computer that has Windows XP. I now have a new computer with Windows Vista and I can't access the secure part of the USB key. When I try to access the part secure the USB key I have the following message "Application [-10004] could not find any JumpDrive Secure device connected to your system. Please make sure that your JumpDrive Secure device is inserted into a USB port". Of course, the USB key is inserted into the USB port. If anyone can help find me a way to access the part secure the USB key I would appreciate it. Thank you. Hi Jon0909, The error that you received can be for several reasons. I suggest you try the following steps: Method 1: Run the fixit available in the link below and check if that makes a difference Tips for solving problems of USB devices
Method 2: This normal matter as a result of a conflict between the USB and other USB (Universal Serial Bus) connected to the computer. (a) disconnect all the external devices connected to the computer to expect the mouse and keyboard, check if your USB key works. (b) If this solves the problem, and then add back both devices until you discover the piece of hardware causing the issue. If the problem persists, you can contact the manufacturer of the device for any known issues Thank you, and in what concerns: Ajay K Microsoft Answers Support Engineer "Not enough memory is available to process your order" when you try to install the drivers Recently, I have problems when you try to install the drivers for a USB mouse that I have. When I plug the mouse, it detects it and tries to install the software but it gives me an error saying he found the software but can't install it because "not enough memory is available to process your order." I spent a bit of time, search tries to find a solution to this problem, and I tried a lot of things without success. I tried the things: -Manually installed the drivers. While I can install them, Windows does not recognize the drivers as being installed and the mouse still not working. -The fix IRPStackSize. It was not in the registry, so I thought this might be the solution, but it does not solve my problem. -Troubleshooting and repair of Windows Update. I had a memory leak problem with Windows Update, so I thought fix which would cure the problem. I was able to d/l an update that corrects this problem, but it does not solve the driver problem. Anyone have any ideas on how to solve this problem? Thanks in advance. Hello Thank you for your response. I appreciate your time. I suggest you run the system file checker (SFC) and see if it helps. System File Checker is a Windows utility that allows users to find corruptions in Windows system files and restore the damaged files. Please keep us informed. Thank you Original title: ReplSync.dll - error loading DLL cannot load resource dll: REPLRES. RLL the specified module could not be found I get this error message whenever I start my computer: replsync.dll - DLL Load error can not load the resource dll: REPLRES. RLL specified module is not found Help please? Thank you!
The Advanced Boot Options screen lets you start Windows in advanced troubleshooting mode. You can access the menu by turning on your computer and pressing the F8 key before Windows starts. Some options, including the mode safe mode, start Windows in a limited State, where only the essential is started. If a problem doesn't reappear when you start in safe mode, you can eliminate the default settings and basic device drivers and services as a possible cause.
If the problem does not occur in safe mode, and then try to perform the clean boot and see if the problem still occurs. Clean boot helps eliminate software conflicts. For more information, see the following link:
NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the article mentioned above. Method 2: See the following link for more information about the same: What is Windows Defender in offline mode?
Method 3: SFC/scannow is a very useful command that you can use in any version of Windows. When the SFC (System File Checker) command is used with the/scannow switch, the tool analyzes all the important files of Windows on your computer and replace if necessary. Missing and the corruption of the operating system (like many DLLs) files are probably the main cause of the major problems of Windows. In view of this, plus the fact that the SFC/scannow is completely automatic and very easy to use, the tool should be usually one of your top not troubleshooting. Reference:
How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7 Let us know if it helps! I am connected but you get the error: "not connected - connections are available. I am able to connect to internet with my HP dm1-3025 x netbook (running Windows 7 Home Edition Premium, SSD 240 GB, 6 GB RAM) but will have the following problems. Hello I suggest that you want to run system restore to the date it was working fine. System restore Once you do the system restore, then I suggest you to download and install the updates from the Download Center. http://www.Microsoft.com/en-in/download/default.aspx I do not have any manual or windows seven cd when I bought my hp pavilion dv6 laptop 6115 tx. I do not have any manual or windows seven cd when I bought my hp pavilion dv6 laptop 6115 tx. Am I supposed to do? I bought it in this store called "Staples." Hello There is no DVD or CD with operating system. You must create a set of recovery disks. Resources: Using HP Recovery Manager in Windows 7 There is no paper manuals. Click the Windows Start button. Write in the search box " Documentation HP " and run it. You will find all the documents. I get an 'Error Javascript applet' ad in most of the pages in Firefox? It is a problem for me with most of the Web sites when I try to open them in Firefox. It does not exist in other browsers (IE, Chrome). AVG Free anti-virus analysis reports errors potentially dangerous following rootkit AVG anti-virus free the following errors of potentially dangerous rootkit analysis reports - ' ";" C:\WINDOWS\system32\drivers\sppz.sys «;» ATAPI.sys, Hung import HAL.dll READ_PORT_USHORT-> sppz.sys + 0x20C0"; "' Object is hidden" ' ";" C:\WINDOWS\sy Hello I tried to save my Xperia from Sony Go with Sony PC Companion on and off the past year. He has not systematically each time and I let slip in the past, but I really need to back it up. At the time when I go through the backup procedure, choose original title: office / Home compatibility My office uses Windows 7 and my computer is running Vista 64 bit. My home computer can work with my office from a USB files? Signature of ndk 10 key problem vs ndk 2.1 I submitted an app for OS2.1. Now, I want to present a version to OS10. I go to the vendor portal and select "+" to add a new version. When it comes time to add the file, I get: File bundle (xxx.bar) was rejected. Package ID is required for all .bar Similar Questions
properties) properties)
http://www.HP-ProtectTools.com/downloads/PDF/HP_ProtectTools__EnterpriseDeviceAccessManager_Whitepaper.PDF
Router (config-controller) slots #pri - Group 1-31
% Not enough resources available to configure pri-Group on controller E1 0/0 DSP
/ 0
% Remaining the dsp resources are sufficient for intervals of time 0.
% For the current complexity of codec, 2 extra 16 channel dsp (s) is required to create
This voice port.
DSP groups on slot 0:
DSP 1:
State: UP, firmware: 32.1.1
Signal/voice of max channel: 32/32
Credits of max: 480, voice credits: 480, video credits: 0
num_of_sig_chnls_allocated: 6
Transcoding allocated channels: 0
Group: FLEX_GROUP_VOICE, complexity: FLEX
Credit splitting: 96, reserved credits: 0
Signs of the allocated channels: 6
Voice of the allocated channels: 0
Appropriations used (rounded): 0
Group: FLEX_GROUP_CONF, complexity: CONFERENCE
Credit splitting: 0, reserved credits: 384
Codec: CONF_G729, maximum of participants: 8
Sessions by dsp: 5
Slot: 0
Idx device: 0
PVDM slots: 0
Type DSP: SP2600
This command is not applicable to the slot 1Importare immagini da una o digital fotocamera da a player di schede multimediali
http://Windows.Microsoft.com/en-us/Windows-Vista/restore-files-from-a-backup
http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-and-restore-frequently-asked-questions
Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
http://www.Lexar.com/support
---------------------------------------------------------------------------------------------------------
Visit our Microsoft answers feedback Forum and let us know what you think.
Reference:
Use the System File Checker tool to repair missing or corrupted system files
https://support.Microsoft.com/en-us/KB/929833
You can try to start in safe mode and check if the problem persists.
http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode
Step 2:
You can run Windows Defender Offline tool.
Windows Defender Offline: Frequently asked questions
Note: data files that are infected must be cleaned only by removing the file completely, which means there is a risk of data loss.
Try the SFC (System File Checker) scan on the computer.
http://Windows.Microsoft.com/en-in/Windows7/products/features/system-restoreMaybe you are looking for