Qosmio F10-105 only works with the 600 MHz

Similar Questions

• Satellite A210 - 10 c only works with the 800 Mhz instead of 1.6 Ghz

  Hello

  I have a very big problem. One day, I look in Vista on my resource monitor and see that the max freuquence is only 50%.

  So first of all I think that is no problem because the assets 'energy savings' energy recorded.
  I have a Satellite A210 - 10 c portable.

  So I switch to maximum power and perform a test of prime95. But hell, the max freuquence has not changed. I also installed everest and cpu z, but all programs show the same to me:

  My laptop only works with the 800 Mhz instead of 1.6 Ghz!

  I'm looking for drivers for the AMD processor, but you need not for Vista. Update all the drivers of Toshiba and Programms and BIOS (in fact, it is the 1.9).

  Nothing helps.

  As a last test, I reinstalled Vista, but also did not help.

  And now I'm at a loss what to do.

  I hope someone can help me.

  Good bye...

  Have you installed the Vista using the recovery CD or the original CD of Microsoft Vista?

  I ask because the restore CD contains all drivers for Toshiba and yellow exclamation marks should not be apparently in Device Manager.

  If you used the original CD of Vista I think that you have not installed the Package of Intel Robson.

  I found the package of Robson on the Toshiba driver-> Satellite P200 area page.

  Maybe you should check this.

  Your comments would be appreciated

• Satellite M30-801: CPU only works with a 600 MhZ

  Hi people, I have a strange problem since my PC back to toshiba support (lcd problem, on assistance report i red that the pcb has been replaced): my CPU goes up to 600 MhZ. I tried to update the version of the bios from 1.20 to 1.70 successfully and I have restored the default value believing it could be a related problem of bios , but nothing changes.

  The problem is present in a new installation of Windows XP (from recovery CD), so I think I could exclude a software problem.

  Any ideas?

  Thanks in advance
  Roberto

  Hello

  The update of BIOS does ' t solve this problem.
  It seems that the Toshiba service partner forgot to start several compatibility tests. This is necessary after some repair procedures. Without this additional test, the CPU does not work with maximum efficiency. Well, there is nothing to see. You must contact the service again and it should solve this problem.

• BlackBerry Z10 headphone only works with the left ear

  My headphones (beats studios) only works with the left ear when connected. The helmet has never had a problem on my old iPhone 4 and currently with my rMBP so I know that's not the headphones. Any suggestions?

  There seems to be a problem with the jacket of the head. They are defective for a few pieces and the jacket cannot recognize the HP in the same case, what makes the phone to give no sounds on the notification.

  Try to use different headphones. If the problem persists try replacing the model.

• HP Pavilion dv7-6c02sm USB 3.0 only works with the 2.0 speed;

  Hello

  My HP Pavilion dv7-6c02sm has 2 USB USB 3.0 ports on the left site of my laptop. Currently, I installed these "sp55102" driver - Renesas Electronics USB 3.0 host controller driver

  When I connect my WD 1 TB USB3.0 ports chip I just get the message that he could run faster if I connect through a Super speed USB3.0.

  I tried all ports and all give me the same answer. I googled for a manual and myself made sure that my USB 3.0 are on the left side. And ports give me the same notification so I think it will be a driver problem. Could not find a better then sp55102.

  When I copy files, the left USB ports work at a lower rate than normal USB 2.0 on the right side.

  On the side USB 2.0 right arround 25 Mb/s and the left a USB 3.0 starts at 25 and plunges in 13-15 Mb/s

  I formatted my drive and installed new firmware for my external hard drive, but it does not solve my problem so I'm pretty sure it's a driver issue, but I can't find a more suitable, more recent and better driver.

  Product: A9X57EA #BED

  Help, please. Thank you

  Hello

  Ok... I've solved the mystery

  After hours hours of research online I thought that it is mostly a problem of windows 7 because windows updates are not installed to the end. In the end only USB worked with 3.0 but there was an optional windows update install and atfer install the optional update (which is dealing with something) the two USB 3.0 working at a speed of 120 MB/s

  Also, you should check your chipset on the following link

  http://www.Intel.com/p/en_US/support/idyp

  If you use the latest version on the drivers to install Renesas Electronics USB 3.0 host controller driver. I found this to be the last version USB3.0_allOS_2.1.28.1_PV

  
  So if anyone has the same problems with his speed USB3.0 and make the message "this device can perform faster if you connect it to a Super speed usb 3.0" is really the solution. You need to update your system with windows update and by that I mean, you want to be rushed to insatll everything to the system and upgrade your windows to the possible limit maximum!

• Uploading to FTP host... only works with the file of the Web server root

  When I download a Muse site to the root of the Web server, everything works as expected with the obvious comparison.

  But if I want to download on a file/folder existing... it doesn't work. Muse download files but no files are added on my Web server.

  I know how to add the path if I do something wrong or there at - it a bug somewhere?

  Thank you.

  I should add that the Muse site emergency or any html Web site doesn't not any sense. Backup is only valid for cms. And this isn't just a copy of the files in the site, it has a copy of the database. Muse has no database. Backup of the Muse - is file.muse, which can be placed anywhere.

• Palm tx only works with the charger plugged

  My palm that TX only works when it is plugged into the ac charger.  The symptoms started after I left unused device for about 2 weeks.  When it is plugged in, I get the symbol of battery charging.  The battery icon says 100%.  As soon as I unplug the charger, it dies.  I left it plugged for 2.5 hrs and still does not work when I unplug. I tried to reset hard with no improvement.

  Do I need new battery?

  Thank you

  A last ditch effort - connect the charger and press the reset button.  Let the TX through a soft reset and let it charge for a few hours.

  If still no joy, so yes it looks that your battery has reached the end of its useful life.

  Many places online will repair it for you, or allow you to buy a battery and DIY.  See directfix.com for a video on the TX of repair.

  WyreNut

• Can I use the magnetic charger shows to recharge my iPhone or it only works with the watch?

  I'm looking to see if my Watch magnetic charger will also charge my iPhone. Can someone help me understand this?

  Hello

  Non - magnetic charge cable only works for load your Apple Watch.

• Qosmio F10 does not work after the recovery procedure

  Hi, I just bought the toshiba recovery dvd for my qosmio laptop f10, I put the dvd in and it goes through the process of recovery and complete 100% he then told me to remove the dvd, and then press CTRL ALT DELETE to restart the computer.

  In doing so, he gets to the screen were it tells me windows startup and then the screen turns white and flickers a couple of times, and then the computer phone re boots and don't stop doing that, I press the F8 key when it restarts to go save mode, but when it starts in mode it tells me that windows is not completely set and goes no further and tells me that I need to run put in place to new.

  I don't have a windows cd only toshiba dvd that should put my laptop back to factory settings.

  Can aynone help me before I have sound toshiba?

  Thank you.

  Hello

  It's not easy to say why it happens. Usually, the Toshiba Recovery CD should work properly and after any recovery procedure, the laptop should run without any problems.
  You suggested that you ordered this CD from recovery of the ASP.
  Do you have the right recovery CD? Check the description of CD.

  The other possibility is that the device has a hardware failure. In this case, you must contact the service of Toshiba. Sorry, but that's all I can suggest.

  concerning

• Qosmio F10: What to do with the update tool CD after the replacement of the motherboard?

  Hi, hoping someone can help.

  My F10 had three new mother advice, since one broke down. Fortunately, I had paid for the extended warranty. However, when she came back this time they had formatted my drive was hard because they changed the chip set. Now he can't find a TV signal and the FN keys do not work. They sent me new CD-ROM entitled "Update Tool" and "Qosmio Player Update", but they do nothing to help the problem. Anyone has any ideas or will he be back again?

  Thanks in advance
  Chris

  It of very strange that you didn't receive the Instructions for use.
  Have you checked if there is any description how to upgrade the utilities?

  I think that if you have not received any operating instructions how to use the update of the Tools CD, you should ask the guy to service for such documents.

  In my opinion, the update of the tools is necessary because the new material and new chipset was installed and in this case the old drivers or utilities would not work.

• HP Pavilion dv6-black screen only works with the external monitor

  I discovered that my screen was not turn on yesterday when I tried to turn on my laptop. Fortunately I was able to plug it into an external monitor with a VGA cable and I have a monitor in my office, but I can not really be restricted to my living room or office to use my laptop.  Y at - it easy fixes to this, or is my only option to take it to someone with experience that replace the monitor for me?

  Hello

  Given the external screen display there are so few opportunities...

  -Sun display-project is a flashlight on the screen and check if you can see the bottom - if background is visible while it is the backlight in the LCD screen that needs to be replaced.

  - Display dark: if it is completely black and nothing is visible when you Flash light on the screen, then it is due to the LCD screen itself might be a broken screen (a cable that connects to the motherboard screen) or could be inverter LCD.

  If the laptop is still under warranty so I recommend you call HP tech support and they will be able to get it fixed for you.

• My company says that Firefox only works with the 3.6. It seems like if I'm really going back.

  I was unable to connect to the American Greetings Web site for displays. When I called their support, they said that I had to use IE. I HATE this show. They said that if I wanted to use Firefox I needed 3.6, I downloaded, but that was the way back. Can I do so that I have the current version?

  You are better to install Firefox Portable 3.6.25 on your hard drive so that a Web site and continue to use your current version elsewhere. The Portable version will install completely separate from your current installation. otherwise, if you install a 2nd 'ordinary' version, you need to tinker with separate 'profiles' for both.

  http://PortableApps.com/apps/Internet/firefox_portable/localization#legacy36
  
  Download and install it as you would with any program.

• M200: Processor only works with 600 MHz - why?

  I noticed that when you change a pcb for a laptop regardless of the speed of processors it works to the slower which is 595/598 MHz.
  Have you noticed this? What is the reason behind?
  What is the solution?

  If the processor is to have 256MB / 512MB RAM this custom of things affect a large but for 1 GB & 2 GB the machine's performance becomes very problematic.
  I tried the update of DMI, it has not helped.
  Re-install os also did not help.
  The upgrade of BIO also did not help.
  Also I'm not very sure about this problem with a report any with pcbset change.
  With the right machine, I found the way that is switching dynamically from bios processor capabilities.
  In some machines that give problems I have not observed this option in the BIOS.

  The machines are PortA200 & Port M200 (tablet).
  someone can help me. I need to justify this to the customer.
  Thank you & best regards
  ChaitanyaN

  Hello

  This problem occurs after the change of motherboard. Usually after mainboard change it is very important to bring tests and diagnostic procedures. Without this procedure, the CPU works with fixed 600 MHZ.
  You should contact Toshiba service to resolve this problem of CPU.

  PS: This theme has been discussed here in the forum. Please check this:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=8492&MessageID=29400#29400
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=4351&MessageID=14808#14808

• Remote control not working only not with the G10

  Hello
  my remote was working initially. now it does not work in Qosmioplayer or WinMCE mode. The red light in the receiver when you press the remote control in order to do not a dead battery! any suggestions as to what was popular up

  Hello

  Have you installed any other tools or utilities, or have you changed a few settings?
  As far as I know you need the infrared receiver only to control the MCE Win.
  The receiver is plugged into the USB port. Please check in Device Manager if the receiver is recognized. Also, check the cable of the infrared transmitter is also related.
  However, if you are working with the Qosmio player receiver should be removed from the unit.

  Moreover, in the user manual, you can find useful information about the remote control

  Best regards

• Updated and now the phone won't work online only works with 4G

  Download ios 10 and now my phone does not work online only work with 4G

  Hello thomas.friar,

  Thanks for asking for help with your iPhone to connect to the internet via wi - fi since the upgrade to iOS 10. We don't like to hear about the problems that occur after an upgrade. Here's what I recommend.

  The first thing we want to make sure that all of your data on the Mac and the iPhone is safe. For iPhone, you can perform a backup in iCloud or iTunes using this article: backing up your iPhone, iPad, and iPod touch.

  Then, follow the steps in this link: If your iPhone, iPad or iPod touch connects to a Wi-Fi network

  Thanks again and have a great rest of your day.