HP Pavilion dv6-black screen only works with the external monitor

Similar Questions

• Reference Dell 5558, 8 beebing on startup, no black screen and works with the beebing

  Hello

  I have a problem with my Dell insipiron r15 5558, I bought it 3 months ago. But last month my laptop beep 8 times at startup. When this happens, I usually only the power out of my laptop because of the distracting noise and turn it back on. Once I powered on / off power for 3 - 4 times it don't beep plus one works very well. Anyone know what could be the problem? I ran a Test LCD and an analysis of Pre-boot system, it was running fine without any problem, I used my warranty and sent the labtop to dell here the last 2 weeks, they sent and didn't tell that it is no problem with my laptop, but it is still beebing 8 times by clicking on the power on

  BTW. I'm on Windows 10 pro 64-bit

  Hello

  8 attention beep is usually to do with the problems of LCD, as you already know.   If diagnostics are passing and the system has been returned to the warehouse for the evaluation, the only thing I think it could be is a connecting cable of the LCD screen.  You said sometimes works very well after starting several times, then maybe it's the cable.

  Have you tried to hold the screen in different positions when it turn on?   Just to see if guidance works better and maybe the cable is a better connection.  You can check if the cable is loose yourself.  Here is a link to the online manual for the Inspiron 15r 5558.  You can use it to see how a screen is normally replaced, but instead to replace it you would just check the connection of the cable to make sure it's tight.  NOTE: Make sure you follow the safety instructions and information in the section "before you begin".

  Let us know if you find a loose fitting and if the adjustment of the angle of the screen change anything when you try to turn on the system.  I hope it's something as simple as a bad connection and you can correct it.  If the ringing continues I recommend to contact Dell support again and have them send it back for repair, unfortunately.

  Todd

• Inspiron One 2320 - All In One No Image displayed. Works with the external monitor.

  System works properly when connected to an external monitor. I use it for this type. Built in touch screen does not display any image, but turns on and stays on. That's all just white. I took it to a guy from the local computer that has not been able to diagnose. He changed the LCD cable I think, he said. I have updated the video drivers.

  Is the monitor shot?

  If I need to replace the screen could I just buy a nontouch screen that is much more affordable and replace it with that?

  In fact, I give you a link to the manual in my last post, but had broken in this post then try this link.

  Instructions to remove the touch control panel, screen Assembly and then the display panel begins on page 105.

• Satellite A210 - 10 c only works with the 800 Mhz instead of 1.6 Ghz

  Hello

  I have a very big problem. One day, I look in Vista on my resource monitor and see that the max freuquence is only 50%.

  So first of all I think that is no problem because the assets 'energy savings' energy recorded.
  I have a Satellite A210 - 10 c portable.

  So I switch to maximum power and perform a test of prime95. But hell, the max freuquence has not changed. I also installed everest and cpu z, but all programs show the same to me:

  My laptop only works with the 800 Mhz instead of 1.6 Ghz!

  I'm looking for drivers for the AMD processor, but you need not for Vista. Update all the drivers of Toshiba and Programms and BIOS (in fact, it is the 1.9).

  Nothing helps.

  As a last test, I reinstalled Vista, but also did not help.

  And now I'm at a loss what to do.

  I hope someone can help me.

  Good bye...

  Have you installed the Vista using the recovery CD or the original CD of Microsoft Vista?

  I ask because the restore CD contains all drivers for Toshiba and yellow exclamation marks should not be apparently in Device Manager.

  If you used the original CD of Vista I think that you have not installed the Package of Intel Robson.

  I found the package of Robson on the Toshiba driver-> Satellite P200 area page.

  Maybe you should check this.

  Your comments would be appreciated

• BlackBerry Z10 headphone only works with the left ear

  My headphones (beats studios) only works with the left ear when connected. The helmet has never had a problem on my old iPhone 4 and currently with my rMBP so I know that's not the headphones. Any suggestions?

  There seems to be a problem with the jacket of the head. They are defective for a few pieces and the jacket cannot recognize the HP in the same case, what makes the phone to give no sounds on the notification.

  Try to use different headphones. If the problem persists try replacing the model.

• is it possible that a single screen will work with the slider and second focus mode

  Hello

  can you please tell me is it possible that a single screen will work with cursor mode and second focus mode.

  Thank you

  Hello

  I don't think that it is possible to change the mode of the development of your application outside of in the config.xml file.

  A custom extension may be able to do this, but I have not seen anyone this yet.

• HP Pavilion dv4: can I factory reset with an external monitor attached to my laptop?

  I got a laptop HP Pavilion dv4 entertainment PC. It has a cracked screen and I use an external monitor attached. Can I do a factory reset with the attached external monitor? The monitor is an HP w1815 LCD, case ini that matters.

  Thanks for any help on this.

  I would like to add that I can see on both screens only on screen cracked that I can't see the bottom of it due to cracking. As recovery options are visible on the external display, it would be prudent to start the recovery process? I made a few choice, but I am now at the point choose to 'pull the trigger' and click next to start it or hit Cancel.

  Thank you.

  Hi @Auntboris,

  Welcome to the HP Forums!

  It's a great place to find answers and advice!

  You have the best experience in the HP forum, I would like to draw your attention to the HP Guide's Forums:

  Learn how to post and much more.

  I take that you acquired an HP Pavilion DV4 laptop and want to know if you can do a factory reset with an external monitor because of the cracked screen.

  Yes, you can always make a recovery.  Here is a link to HP Notebook PC - perform a recovery of the system (Windows Vista) HP

  Here is a link to HP laptops - how to restore backup files created during the backup procedure F11 to help restore your files if you selected this option.

  Please keep me updated.

  Good luck!

  Thank you for your participation in the Forums of HP! We want to help you as well as others who may encounter a similar problem as yourself. Please consider tagging the post in order to solve your problem as "accept as Solution" to help other members of the community!

  To show recognition for my efforts, please click on the ""Thumbs Up Icon " below."

• Tecra A10 - 1LL - connection with the external monitor

  Hello

  I have a problem with my laptop Tecra A10.

  When I connect to an external monitor to the laptop I have to manually switch the screens because external shows nothing. When I disconnect the monitor I have to pass the screens manually with FN + F5 because the internal display shows nothing.

  My old laptop (Tecra A9 (PTS52E-0E702NGR)) is the poster automatically whenever I connected or disconnected an external monitor.

  Anyone has an idea why the A10 light automatically as the old notebook? Maybe it's the only spot in the preferences of the display driver that I don't see right now. :-)

  Hi SilverWizard,

  What happens if you try to switch on the external monitor using the options of display driver, or that this combination of buttons don t work?

  As wrote Al - eX you must update tools from Toshiba to get the keys FN working again. Everything can be downloaded here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  It's working now?

• HP Pavilion dv6 - black screen on startup, but works using the secondary monitor?

  I use a Pavilion dv6 WV815AV, and I used it for 3 years now.

  I tried to start the computer and the fan and lights are lit, but not the monitor.  I tried to plug in my high school, and it's that now treats as if it were the only screen.  I had problems in the past of a few times where I would get past the HP logo, and then there would be a substantial delay where the screen remains black but be illuminated, but most of the time that he would go to the screen connection, and if not, a simple reboot managed to solve the problem.

  Thoughts on how should I solve it?

  Thank you!

  Hi mybluesock, sorry to hear that you have a problem with the monitor not just not. I did some research and I found a document that can help you. Click on the link for the document.     http://support.HP.com/us-en/document/c01997899

  If this does NOT resolve the problem, please do not hesitate to write back and I'll do more research on the issue.

  Thanks in advance

• HP Pavilion dv6: black screen with cursor after the connection

  For two weeks, my laptop lost sound through the speakers and plug headphones.  The computer recognizes there is a problem of devices not be enabled on troubleshooting menus, but when I check the devices individually and test says they are on and sound screens played... even if there is none.

  Due to this recurring problem, I downloaded the drivers for my system updated and uninstalled the old series and restarted my system.  Since then, I get a black screen after login and could make even spybot search and destroy scan my items, but that's all.  Computer still starts in safe mode and can run the Task Manager... Help?

  Hello

  Boot the computer normally and log.

  Black screen, hold down the ctrl and alt keys and press delete.

  Select Task Manager.

  Select the process tab and select to show processes from all users (lower-left).

  Click the column heading to organize the processes in alphabetical order.

  Look for an entry called to run once Wrapper (RunOnce.exe) - If you see it listed, right-click on it and select end task.

  If your office now appears, download AdwCleaner on the following link (there are 4-5 second delay until it's available)- Save in your downloads folder.

  https://toolslib.NET/downloads/finish/1/

  A once downloaded, close all programs, open your download folder and double-click the application to run it (click Yes to any uac prompt).

  Click the scan button.

  When the results are displayed, click the Clean button - when you are prompted to restart, click Ok.

  It starts on the desktop correctly now?

  Kind regards

  DP - K

• HP pavilion dv5: black screen only see cursor

  After you connect to the screen turns black with only the cursor indicating

  Hello

  Try the following.

  Boot the computer normally and log.

  Black screen, hold down the ctrl and alt keys and press delete.

  Select Task Manager.

  Click on file and select the new task.

  Type rstrui - also enter a tick in the box for "create this task with administrative privileges" - and click on Ok.

  When the system restore interface is loaded, choose a restore point at least 48 hours before the opening of the session the question first and then proceed with the restoration of the system.

  Kind regards

  DP - K

• HP Pavilion dv7-6c02sm USB 3.0 only works with the 2.0 speed;

  Hello

  My HP Pavilion dv7-6c02sm has 2 USB USB 3.0 ports on the left site of my laptop. Currently, I installed these "sp55102" driver - Renesas Electronics USB 3.0 host controller driver

  When I connect my WD 1 TB USB3.0 ports chip I just get the message that he could run faster if I connect through a Super speed USB3.0.

  I tried all ports and all give me the same answer. I googled for a manual and myself made sure that my USB 3.0 are on the left side. And ports give me the same notification so I think it will be a driver problem. Could not find a better then sp55102.

  When I copy files, the left USB ports work at a lower rate than normal USB 2.0 on the right side.

  On the side USB 2.0 right arround 25 Mb/s and the left a USB 3.0 starts at 25 and plunges in 13-15 Mb/s

  I formatted my drive and installed new firmware for my external hard drive, but it does not solve my problem so I'm pretty sure it's a driver issue, but I can't find a more suitable, more recent and better driver.

  Product: A9X57EA #BED

  Help, please. Thank you

  Hello

  Ok... I've solved the mystery

  After hours hours of research online I thought that it is mostly a problem of windows 7 because windows updates are not installed to the end. In the end only USB worked with 3.0 but there was an optional windows update install and atfer install the optional update (which is dealing with something) the two USB 3.0 working at a speed of 120 MB/s

  Also, you should check your chipset on the following link

  http://www.Intel.com/p/en_US/support/idyp

  If you use the latest version on the drivers to install Renesas Electronics USB 3.0 host controller driver. I found this to be the last version USB3.0_allOS_2.1.28.1_PV

  
  So if anyone has the same problems with his speed USB3.0 and make the message "this device can perform faster if you connect it to a Super speed usb 3.0" is really the solution. You need to update your system with windows update and by that I mean, you want to be rushed to insatll everything to the system and upgrade your windows to the possible limit maximum!

• Startup message: black screen error box with the instruction at 0x7468a9df referenced memory at 0 x 000000000. the momory could not be read.

  Original title: What happens when I turn on my computer. Why? black screen with error box the instruction at 0x7468a9df referenced memory at 0 x 000000000. the momory could not be read.

  When I turn on my computer, get this Windows logon error message: logon UI.exe

  black screen with error box the instruction at 0x7468a9df referenced memory at 0 x 000000000. the momory could not be read.

  Hello, help,

  Unplug all devices - printer, speakers, digital camera, etc...  The attempt to start start

  You are able to go in Mode safe mode with networking?    Restart and the logo of computer, start typing F8.  See if you can download this file and run a scan complete for malware.

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&id=16

  If the auditor of applicable system files, run

  Right-click on command prompt and select run as administrator

  Type SFC/scannow

  Note: there is a space between SFC and /scannnow

  Press enter

  It will take a few moments for the analysis to be performed.  You can find the paper pressing the Windows flag key + r to open the run window

  Type %windir%\Logs\CBS

  Press OK

  Search for ""impossible to repair corrupt files"Note all corrupted files that are not repaired."

  Try to extract the file to your recovery CD.  It is possible Logonui.exe has corrupted.

  http://blog.NirSoft.NET/2009/09/17/how-to-extract-missing-system-files-from-the-DVD-of-Windows-7vista/

• Black screen of U2414 with the flicker photo

  Hi team, support

  I have u2414H Dell screen that plays up. After several minutes of fed without problem on the screen go black and then intermittently flash the image on a nothing between a fraction of a second for a minute. This will continue until the monitor is disconnected and reconnected. The power button stays white all the time. By pressing the buttons mode does not answer either. If I press the power button if it is in a short work phase the white rest button but the screen would then become completely insensitive.

  I tried several cables and sources so I can confirm that what is happening on the DisplayPort and HDMI ports. I ran the Self test when the screen changes colors and she even did for that.

  Looking forward to your reply,

  Dave Evans

  Good troubleshooting. Get it exchanged.

• Uploading to FTP host... only works with the file of the Web server root

  When I download a Muse site to the root of the Web server, everything works as expected with the obvious comparison.

  But if I want to download on a file/folder existing... it doesn't work. Muse download files but no files are added on my Web server.

  I know how to add the path if I do something wrong or there at - it a bug somewhere?

  Thank you.

  I should add that the Muse site emergency or any html Web site doesn't not any sense. Backup is only valid for cms. And this isn't just a copy of the files in the site, it has a copy of the database. Muse has no database. Backup of the Muse - is file.muse, which can be placed anywhere.