Qosmio F10 - DVD RAM mast * a UJ - 830 s firmware 1.0

Similar Questions

• Qosmio F10: DVD-RAM UJ 830-S - I can not burn audio CD

  I am not able to burn audio CDs with my laptop F10-130.

  Is it possible to get an update for the DVD-RAM UJ-830 s

  Hello

  If you are able to burn another one to think there is a problem with your burning software I put t know not which you use, but please try to install another (Nero) and check if there is the same problem again.

  I think that you n t need any update of the player if there is some problem with CD audio.

• Tecra S2 DVD - RAM mast * a UJ - 830 s

  On the page of the driver of the TecraS2 there is an update for the carpet * a DVD - RAM drive.

  Only when I start it it gives the error.

  The target disk is connected nit.

  Well, I know of course that it is now only one thing that I noticed and that AI says the F/W charger (in the upper area of blue Hey) F/W charger UJ - 831B_V1.02_01

  My S2 is provided with a UJ-830 s firmware v1.oo.

  Is the charger F/W for the different 830 831 a can they use the same software?

  If this isn't the case, Toshiba please put correct drivers it for 830 versions.

  Hello

  are you talking about drivers or firmware? And where did you find the UJ - 831B_V1.02_01? AFAIK there is no update available for the S2 with XP driver.

  Good bye

• Qosmio G20 - DVD RAM i/o device error

  Hello

  I need help.
  My dvd ram driver do not work dvd.

  When I run the dvd he told me "the requested could not be performed because of an i/o device error" and I don't know how to fix it.

  Try to remove the optical drive from Device Manager, and then restart your laptop.
  The reader should be recognized again and correctly installed.

  Please try to test again the feature with CD or DVD media.

  You can use ODD as boot device?
  ODD is displayed correctly in Windows Explorer?

• Qosimo F10, MAST * a UJ-830 s firmware update?

  Where is the update of firmwhere for the CARPET * a drive UJ-830 s mounted on my Qosimo F10?

  The drive does not burn more than 1 x on most media.

  Hey Austin,.
  I wrote a thread on UJ-830 s too because mine doesn't read DOUBLE LAYER DVD-Rs.
  (http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=9002&tstart=15)
  I would be interested to know if you have tried the DOUBLE LAYER media on your UJ-830 s? Can the drive read/play them OK?
  Later,.

  Alcahest

• Re: Qosmio G20: DVD-RAM UJ-845 s does not read CDs or DVDs

  I'm a big supporter of Toshiba product.

  Please help me

  Given that I had to do to update form my * Toshiba Qosmio G20-123 *.
  My * DVD UJ-845 s * do not read any CD or DVD.
  Before that, he worked a lot of good. But unfortunately now, he does ' t read anything.

  The system to recognize it. The driver is installed and working properly.

  After I installed supports DVDRAM of Toshiba.
  The same thing occurs when playing a CD, the system tells me:

  * E: / not accessible *.
  * incorrectness function *.

  I try with a program on the net but no way.

  I was well able to put the original firmware, but I could not find.
  If someone can do a dump of the original Firmware for me it will be a miracle for me.

  Help, please.
  My great respect.

  I think I can help you:

  Go to my computer right click on the CD/DVD drive.
  Now go to properties; Click the Recording tab and check "Enable CD writing on this drive".
  Now click on apply and restart the laptop.

  Check of workaround and post comments

• DVD-RAM 'Power calibration Error' on Statellite L20

  I have a problem with my recorder Satellite and DVD - RAM (MAST * a DVD-RAM UJ - 841S).
  When I try to burn a CD/DVD (I use Nero 6) often I see information "POWER CALIBRATION ERROR".
  So I have a question: this error is software error or is it a hardware problem.
  Sometimes I can burn CD/DVDs.
  I have Windows XP he SP2
  RAM 512 MB
  HARD DRIVE 60 GB
  Computer is almost 2 years old.
  Thanks a lot for all ideas.

  Hello

  Please check this http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=19024 topic and see what some users think about it.

• Qosmio F20-153 - strange question DVD RAM

  Hello

  recently bought a F20-153 (PQF22E) the DVD RAM drive was a UJ-840 and had the problem of common reading and writing on discs, I have a UJ-841 replacement, but when I set up the BIOS came with the CR ROM of ERROR report.

  So I bought a different known working 840 a laptop Toshiba, it equipped and the BIOS came back with the same ERROR of CD ROM on start up.

  Now for the weird, I closed the lid and went to make a cup of tea and have a think about, when I opened this new Windows has detected the drive, install the drivers, and now I have a working drive... BUT...

  Whenever I stop the laptop, it reports the same error on start up, and yet once there drive when first at Windows startup, but once his punt and I put it in hibernation, the drive appears again and works perfectly.

  I tried this since the 841 and the same thing is happening, just checked in the Device Manager and noticed that while the label says UJ-840, Windows reports the 'new' 840 as a 831.

  I read that the Qosmio player needs must be set to master, this could be the problem? Or Toshiba locking of the type of drive in the BIOS?
  The UJ-831 that I have discovered came from a satellite.

  Sorry this is such a long post, I wanted to just participate as much detail as possible, all you have ideas?

  Had a lot of views but answers just this give a slight bump in case anyone has any ideas

• Satellite A80-129: Mat * a DVD - RAM UJ-830 s cannot burn DVDs

  MODEL: SA80-129
  DVD RAM TYPE MAST * A DVD-RAM UJ-830 S
  SYSTEM: WINXP
  SOFTWARE: NERO

  (1) DVDRAM CAN READ CD AND DVD EASILY, IT Burns CD WELL, BUT cannot burn DVDs, IT SHOWS: G:\ IS NOT ACCESSIBLE INCORRECT FUNCTION, UNTIL IT WORKS WELL. the blank dvd is not a problem, before I used even type a blank dvd to burn.
  (2) even allow the recoding in the properties, the properties shows the Virgin dvd 0bytes.

  all PROMTLY ANSWER would BE MUCH APPRECIATED.

  It doesn't sound good.
  I had a similar problem of combustion and the end of the story, I replaced the drive ;(
  However, try to remove the drive from Device Manager, and then again to restart the operating system should recognize the device again.
  Then you could check if it able to burn the DVD s s.
  I think you should also try burning different DVD media.

  I have visited many work sites and the reader, and especially the calibration lens malfunction could be responsible for burning problems.
  This could be a worst case and in this case, the replacement is necessary.

• Qosmio G35-av600 - DVD - RAM problem

  Hello

  the drive from DVD-ram to my Qosmio G35-av600 died suddenly, he would not read something, so I went to come in and buy a replacement (the model is UJ-856-C), but when I changed the drive and starting the pc, I get an error saying error of CD-rom (I saw in another forum it takes with master-slave config), could someone please help me?

  Thank you very much, any help would be appreciated.

  I think you're an IDE #1 error message. Am I wrong?
  This error message is displayed due to bad settings master/slave/c-salt.

  The parameters of slim-line CD/DVD players is not editable using a jumper.
  The settings are controlled by the software, and to my knowledge it of not possible to change the settings.
  Therefore, not all CD/DVD drives are compatible!

  Before buy you a portable player, you must contact the authorized service provider and ask that compatible!

  Good bye

• Qosmio F10: Cannot read all DVDs recorded on JVC DVDRW

  I have a Toshiba Qosmio F10 in general I am very satisfied with the camera, but... I don't no why I can't play SOME DVD saved on my DVDRW JVC home and not in others, it's driving me crazy, no matter who else has this crazy situation, any suggestions would be most appreciated, as I add another HARD drive to this unit, 60 GB seems a bit small for a work of TV/DVD etc.

  Thank you very much, keep up the good work Toshiba ;-)

  Hello

  What you mean exactly with some DVD s? There is a specific difference between s DVD? Do you use several virgins DVD s from different producers?

  As far as I know you can built in 100 GB HARD drive.

• Qosmio F10 - the DVD writer speed

  The engraver of DVD on my Qosmio F10 is supposed to get 8 X speed, but the speed option I get using Nero or Sonic is 2 X. can someone please advice on how I can burn at X 8 speed

  Hello

  Well, it's not easy to say what the problem is, but are you sure that it s not a defect of operation of media?
  Have you tested another dvd?

  Good bye

• Transfer VHS video to DVD with Qosmio F10

  Hello
  I really need help, I want to transfer my VHS to my Qosmio F10 videos, edit them and then burn to DVD. I have cable supplied with the machine, more I bought a Svideo cable. I have tried all the ways to connect to their place, but without success. Someone would have a go at describing the steps I must follow to do this?
  I'm not a computer expert, simple language not techno would be appreciated.

  Hi Walter,

  You are looking at a three-step process: -.

  1. connect your VHS player to your laptop (S-Video/s-Video is recommended for better quality imagery, but you'll also need to connect the audio cables from your VHS player to your Qosmio for sound.)

  2. change the captured audio and video using a proprietary software package. You may already have Windows Movie Maker installed, but you can also consider other packages of Nero, Ulead, Pinnacle, Roxio, etc.

  3 burn the project finished on a DVD.

  The whole project can be a minefield, so I recommend taking each step in turn and carefully progressing thanks to gain experience.

  Finally, don't download discouraged by the apparent conflicts between the different pieces of hardware and software. The final result will be very rewarding.

  HTH :-)

• Qosmio F10: Question about RAM upgrades

  Hello

  I have a laptop Qosmio F10, and it crashed in the summer 2006, so I sent it to Toshiba and changed it the motherboard. I got a new version with the nVidia card 6600 and I have 2x512MB PC2700S DDR - RAM (the one that came with it, the one I added).

  Recently, I managed to find a buyer for these Rams, to switch to 2 x 1 GB, so my question is: can the motherboard handle faster DDR - RAM (with 400 MHz instead of 333 MHz like the ones I have) or should I just stick with the same model (PC2700 - 333 MHz)?

  Thank you

  Hello

  I recommend you to install a program of diagnosis of equipment as Everest Home edition for example. Then check how fast the bus (FSB) front supports.
  If it s 400 Mhz or faster, then you can use the 400 Mhz memory modules.

  I hope I could help

  At soon amigo ;)

• DVD - RAM drive means that I can burn DVDs & CDs on the Qosmio series F

  Can someone tell me that if I see "DVD - RAM Drive" under my computer does it means that my laptop allows you to record CD and DVD?

  I don't know which series Qosmio F you have exactly, but this means that you can burn CD - R, CD - RW, DVD-R, DVD - RW and DVD-RAM media empty. It must also be possible to use DVD + R and DVD + RW media. I didn t try this because I prefer DVD-R virgins.

  Just for example: my friend has a Qosmio F20-159 and according to the specification of the drive can write monitoring media
  CD - R 24 x
  CD - RW 4 x
  HS CD - RW 10 x
  US CD - RW 10 x
  US + CD - RW-
  DVD - R 8 x
  DVD - RW 4 x
  DVD + R 8 x
  DVD + R (Double Layer) 2.4 x
  DVD + RW 4 x
  DVD - RAM 5 x

  Good bye