Qosmio F10: ERROR: ' unable to ACPI namespace!

Similar Questions

• Qosmio F10 get error 'IDE #0 ERROR.

  Hello all, just bought the Qosmio F10 installed all the things I had to do. installed and registered the norton anti-virus. everything went well. now a few hours later I want to boot my laptop and get the error "ERROR in IDE #0"

  so I put my recovery dvd disk, follow the steps. English start installation, Windows xp, full disk recovery, continue...

  then I get the error: "error checking for a drive partition - please try again! Press a key to continue. then I just get: c:\ >

  That's all I have As

  any help?

  THX in advance,

  Hi Maarten

  I guess there is a problem with the HARD drive. Obviously, the HARD drive is not recognized by the BIOS, and it is not possible to access this topic.

  Please contact your dealer immediately and explain the problem.

  Good bye

• Qosmio F10 does not accept my recovery cd

  My Qosmio F10 does not accept my restore cd. It will not work in windows or dos mode. In windows, I get the error message. This recovery and applications cd is not configured to work with this machine (laptop). This cd is for: Qosmio G10, Qosmio F10.
  Please use the correct recovery and Applications cd.
  I want to format this model and would really like to use the adequate recovery cd to reinstall all applications that I don't have a windows xp disc. Recovery, one is the only one I have.

  Hello Pam

  Insert the recovery media in the drive and turn off the laptop. Wait a second and turn it on. Press the C button and keep it down. On this track, the unit will start playback DVD recovery and if you use original recovery the recovery procedure will be implemented.

  You cannot reinstall the unit if the operating system is running.
  Good bye

• Qosmio F10: update the display driver

  Hi all
  I use a Qosmio F10.
  Preinstalled system shows that Windows uses a generic monitor ("default") and the NVIDIA GeForce FX Go5700 6.6.1.2 version.
  I don't know how to update the monitor driver to one Qosmio use really (and not a generic driver).
  I tried to upgrade to the latest version of the display driver by using the file update on the site of Toshiba UK, but run in a system error, the Setup program could not find the file to uninstall the original driver.
  Any idea?

  Hi Christophe,

  I don't understand what you want to do. You have already installed the new display driver (ver.6.14.10.6612).

  Furthermore the display driver depends on the graphics card not on the monitor.

  Good bye

• Record from VCR on the Qosmio F10 - 101 - no video

  I read a lot of topics but I need some information additional regardin my problem

  I myself Qosmio F10-101

  I tried to record from my VCR on computer, I connect the VCR output to monitor using the came with a computer cable laptop but audio is here and no video... no yes no picture, I used windvd creater which came with the laptop, but no picture, I also tried the s-video input and no image appear also as the program windvd unable to give the icons of all the devices connected to the laptop

  What should I do?

  Hello

  I know, you can not save to your VCR using the monitor and S-video, you can use the port fireware "located right next to the PCMCIA port on the left side of the laptop" with windvd.

  Thank you

• Qosmio F10: WinDVD creator

  Qosmio F10 is for sale with DVD creator, anyone who acquires an analog video with her

  I have a Qosmio (a G10) which came with WinDVD creator but I am unable to capture analog with her. I tried many programs of the trial and can't get something to recognize Tv Tuner or analog in.
  The Qosmio seems to purely through MCE

• Qosmio F10: Driver Installation does not detect the wireless network card

  I wonder if anyone can help before I phone supported again. My motherboard is dead and ASP replaced and recovered my laptop qosmio F10. Since having back, my wireless card did not work.

  Windows detects a "network controller" whenever it starts and gives me the opportunity to install it. I tried to install it by navigating in the 'tools and utilities' records CD rom for folders and subfolders of "Wireless network driver" and it still does not detect the card.

  I also tried to install using the cd rom web gui and selected the 'Pilot wireless network' link and then tried to install it. It opens a dos command prompt and try to install but comes up with the error "failed installation.

  I ran the customer service and they told me to run the qosmio recovery/then recovery of product/recovery of qosmio and again...

  I still don't the card wireless not yet installed. This happened to someone else?

  I tried already shot the drivers from the web, but with no luck... If a representative of customer service with the help of good technical knowledge that would be great, or if someone has encountered the problem too and he had fixed to the give me some advice...

  Thank you very much

  Sean

  Hello

  you see the card wireless as an unknown device in Device Manager? If this is not the case, perhaps that the card was not properly installed after replacing the motherboard.

  Sorry I have no other idea.

  Good bye

• Qosmio F10: How can I install Win XP MCE 2004 again

  Hello

  I have a problem with my recovery dvd - rom supplied with my laptop TOSHIBA QOSMIO F10. I bought in London, message of cams of upward on the screen error "\WINDOWS\SYSTEM32\CONFIG\SYSTEM / Windows didn't start because the following file is missing or damaged '

  But now I live in Brazil, so how can I install again my operation system XP MCE?
  Because I have the OEM software pre-installed in.
  Can someone help me please?

  Don t understand why you open a new topic!
  You have already posted this here:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=25711

• Qosmio F10 does not start system missing or damaged

  I have a Qosmio F10, and I use all the proper procedures for RECOVERY DVD-ROM PROUDCT.

  "I did all the necessary readers updates as well, but when I turn on the laptop came with an error message:" \WINDOWS\SYSTEM32\CONFIG\SYSTEM
  "Windows was not start because the following file is missing or damaged:

  So, now my computer with startup options start, but what that you choose the system starts again and again...

  What to do? Please, I beg you.

  Hmmm usually after using the CD recovery Toshiba, everything should work ok.
  I read on some computer expert sites that this problem could be linked to the hardware failure. The HARD drive or the module memory is possibly corrupt.

  I would first recommend formatting the entire HARD drive (remove also all partitions).
  Install the operating system again.
  If it does not solve this problem you could check if it is possible to install from the original CD of Microsoft XP.
  Further, you can see the memory modules. Try to remove one and use only one or replace it with a new one.

  But please note that these are just my suggestions and I m not 100% sure if these proposals will allow you to solve problems. In any case it s worth a try

• Qosmio F10 - Bluetooth does not work

  Can't get my Bluetooth to knitting - machine came with it already charge. My Palm found once but hangs when I try to transfer the data. Now can't find it. Get an error message when I try to change your preferences on my laptop is detectable and will not save the setting.
  Help!

  Hello, Janet

  I don't know, but all Qosmio F10 do not have Bluetooth. Can you please check it you can see a Bluetooth label in the lower corner of your laptop? It looks like this one http://support.toshiba-tro.de/KB0/FAQ35007I001WR01.htm.

• Green vertical lines then white screen on Qosmio F10

  My Toshiba Qosmio F10 primer is more. When it is on, the windows logo appears and the screen green vertical lines before going completely blank. The screen remains blank for about 5 minutes, then the laptop starts to restart. It justs goes on and so forth.
  No one knows what the problem is and now the laptop is out of warranty, cost for repair, or it is not profitable and it would be cheaper to buy a new laptop?
  Thank you
  Mike.

  Hey Buddy,

  Unfortunately ' unfortunately it seems that this defect is caused by component defective equipment.» It could be that the motherboard together that cost to a service center about 400 European must be replaced. (New card mother and Exchange)
  You can also try to clean your cooling system with a can of compressed air to remove dust which could probably cause the error, also.

  If you really want to give your machine for repair, then follow this link and find nearest ASP in your country:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT

  Welcome them

• Qosmio F10 - drivers help needed

  Hello

  I tried to install the drivers from the site Web Tosihba, but unable to install the following:

  Multimedia Audio Controller - SoundMAX Integrated Digital Audio

  PCI\VEN_8086 & DEV_266E & SUBSYS_02531179 & REV_03\3 & B1B FB68 & 0 & F2

  PCI modem - TOSHIBA software Modem

  PCI\VEN_8086 & DEV_266D & SUBSYS_00011179 & REV_03\3 & B1B FB68 & 0 & F3

  Video controller - NVIDIA GeForce Go 6600

  PCI\VEN_10DE & DEV_0148 & SUBSYS_00051179 & REV_A2\4 & C3FA7 266 & 0 & 0008

  Please I ask for help in installing the drivers for toshiba F10

  Help will be very appreciated.

  Thank you
  Ronaldo

  Hello

  Download drivers for supported operating systems that you can find on Toshiba page under http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp
  Qosmio F10 is old model of laptop, and you can find the drivers in the ARCHIVES.

  You will find there?

• Qosmio F10: How to get help "wake up on Lan.

  Anyone who manages to get working on a Qosmio F10 WOL?
  I found that the power management tab is missing from the properties of Intel (r) PRO/100 VE. Therefore cannot check the "allow this device to wake the computer from sleep mode.
  Read the Intel site that is said to try to uninstall & reinstall the drivers if the power management tab is missing, that I did with a new & the OEM driver, I downloaded from intel, but it did not work.
  The other parameters of WOL under the advanced settings TAB, all seem to be there.

  Before going any further I was wondering if anyone has had this works?
  If not someone from Toshiba can confirm the Bios & motherboard WOL support with built in the Lan card F10?

  Both the program HWSetup & incoming in the installation program, it seems, there is no ACPI definition of boot options.

  Thank you very much

  Qosmio f10
  BIOS 1.20
  Intel® PRO/100 VE driver for 8.0.27.0

  Hello

  On my laptop Toshiba the option allow this device to wake this computer is not accessible.
  So I think that the map network-> properties-> Advanced tab options are responsible for this action.
  On my camera, I can see awakening on the evolution of the link, ARP/Ping alarm and wake up using APM mode.
  There you can activate all options.

  In addition, you can check in the settings of ToshibaHW if the built-in LAN boot and network protocol is enabled.

• Qosmio F10-103, Unmountable_ boot_ volume... What can I do?

  Hello
  I have a Qosmio F10-103.
  One day there is the blue page with
  writing "Unmountable_ boot_ volume"
  appeared!
  What can I do?
  I have red on some forums that it (could) be
  a hard disk problem and that
  I could fix the cpu using the
  boot Windows xp CD, copying files
  Boot.ini, NTDETECT.com, NTLDR... but...
  Toshiba gave me only the DVD - rom backup,
  not boot xp.
  Then I tried to use this end DVD as I entered
  in Toshiba 1.0.1.0 recovery utility
  and I had a disc of control... the result was:
  «Application error 29004»
  Read down sector, result = 1, disc = 128, sectors
  132479 to 132481 if the problem persists contact toshiba... "
  I am here!
  It is useful to say that all modes of starting
  Windows does not work.
  In addition, the "look-like prompt back" that appears
  Once out of the recovery utility does not
  to copy the file, I need the DVD.
  What can I do?
  Is there something to do before... the formatting
  procedure?
  Thank you very much!!!

  Hello

  Check it please this Microsoft article on this error message.

  Microsoft Knowledge Base. Q297185

  Good bye

• Qosmio F10: Recovery DVD does not work?

  Hello. I have a qosmio series lappy F10 series well well I still get random stops, crashes and error log every time that I start.
  It's been very disturbing to me. I tried to use the system recovery cd, that I got with my laptop and when I followed the procedure in the user manual it starts the recovery then flashes that my system does not support recovery.

  Is this normal especially when I had my restore disk with my laptop. I want to reformat my drive hard back to the factory settings and it was completely wiped out with having to buy a new hard drive and windows xp.

  What I do and how can you help me in this? I'm at the end of my teather as one of my tasks is a dj from the internet and I can't keep crashing in the middle of my streaming. I don't want to lose my job!

  Help, please!

  Hello

  Very strange! The fact is that you cannot use the different recovery CD because each recovery CD is designed for a Toshiba laptop model. For example, you can not use a Qosmio F10 on a Qosmio G20 recovery CD.

  However, I assume that you use the recovery CD provided (as you say) and the recovery procedure should generally work without any warnings or error messages.
  I think there is something wrong with the CD. Maybe the wrong CD was shipped with this laptop?
  I recommend to ask the Toshiba ASP in your country. Here, you can also order the new CD.

  Good bye