Qosmio G30 flickering screen with lines

Similar Questions

• Satellite L500/00W - gray screen with lines appeared twice

  Hello

  2 weeks ago, I bought a laptop Toshiba Satellite L500/00W and today I was reading something online that this grey screen with lines to come...
  He did so twice already... I do worry...

  This could be the cause? How should I do? This happen to anyone else?

  Thank you
  Lily

  Hello

  I m not L500 owner so I can't tell you if that happened or not.
  I A200 and U400 for my company and I didn t have shown such symptoms in the past

  He signed strange s if the display changes the brightness and display vertical lines.
  It might be a problem of display or something with the graphics card.

  If you see this new symptom then I would recommend connecting the laptop for external monitor to check if the same would be visible on the screen 2.

  If the same would be seen on 2nd screen there is a big chance that and GPU would be affected.

• Qosmio G30-175: screen starts flickering pixels & funny

  Hello

  I have PC laptop Toshiba Qosmio G30-175. I was working fine until last week. But all of a sudden screen looks funny disappeared.
  When I start the laptop, it starts well and windows start too thin.
  But a few early screen minute flicker and everything on the screen disappear and all the screen do cover with kind of pixels.

  Could someone please advice me, what went wrong for this laptop. Is the motherboard or card went graph.
  If so, how can I get it fixed at a great price.
  Is it possible to change the graphics card.

  much thanks

  Hi mate

  I think I have bad news for you.
  According to your description the graphics card chip begins to malfunction, and I think you have only one chance to solve this problem; the defective part must be replaced!

  I would recommend so contact the nearest authorized service partner in your country and ask for later handling.

  Sorry mate but it isn't alternative :(

  Good luck

• Qosmio G30-204 starts with BSOD

  Hello

  I have a toshiba Qosmio G30-204. It crashed last Friday night, I tried everything since then, including the system recovery disk, nothing seems too much work between the blue screen and a matrix effect in the back round (broken lines going down the screen) so that I erased two hard drives. Nothing seems to work, also tried safe mode and boot into normal windows.

  In the course of the process, I came across a message, if an additional disk came with it! to put it in now. A single disc that I can remember. Any help would be much appreciated, because I now get only a blue screen with the stop 0xoooooo7E (followed by other numbers)

  Thank you once again, Marty

  I got the message?
  You aren't able to recovery of the laptop using the recovery disk?

  Hmm looks like hardware problem
  The described broken lines going down the screen resembles a graphics card problem
  What happens if you turn on the device and go to the BIOS?
  The BSOD is always appear?

• Qosmio G30 - 102 screen completely disappeared

  I read a lot of messages about the green lines, white spot, and blue screens. However my laptop screen has taken a step beyond that and stopped working!

  I have a Qosmio G30 102. I was playing a game (use high amounts of graphics) when suddenly the screen went. I restarted the computer, but it came with the different colors of the Rainbow (green lines, would change to a completely white screen). The problem was once windows starts to load than the screen turns off. I used the function keys to review the settings of the screen (if you want it to be double screen, connected to the LCD tv), but nothing would work.

  I decided to restart the laptop, but it now came with windows not stopped correctly and gave me the options to start the computer and had pixels all messed up (some letters were missing), windows, put in place would not work after the reboot because the screen turns off.

  So now, the laptop is just left with a blank screen. I can't install windows and my warranty is now sold out (ironically just 1 month ago: S)

  Any help would be appreciated!

  Thank you

  I found these Toshiba update document produced on the Europe of Toshiba page:

  http://EU.computers.Toshiba-Europe.com-> download-> Product Updates & support

  _ + Update: update the BIOS Toshiba Qosmio G30 and the GPU + _ repair program
  + This question is strictly limited to the Toshiba laptop computer model which was produced during the period from January 2006 through June 2007. Except as noted below, any other Toshiba laptops are affected. +
  More details on how to deal with this issue, you will find

  Welcome them

• Qosmio G30 (PQG31) - problem with cloned hard drives

  Hi all!

  * Qosmio G30-154 * (* PQG31 *).

  Demo of the Qosmio has 2 hard drives with XP MCE (32 bit) installed on the primary.
  The RAID parameters are JBOD.
  BIOS is "newer" 3.90

  I would try to upgrade the drives (without installing any OS) and... have a problem!
  BSOD "Stop 0x0000007B" after 'clone with resizing' for the main HARD disk.

  I read on [drivers Toshiba RAID | http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=48489] also [how to integrate the AHCI driver when installing Windows XP | http://aps2.toshiba-tro.de/kb0/HTD9401AN0000R01.htm] and (or)
  [SATA and AHCI Intel Matrix Storage Management Software: "the installation program found no hard disk units installed in your computer" Error Message during Manual Installations | http://aps2.toshiba-tro.de/kb0/TSB7B020R0000R01.htm], but I don't want to install OS, I want to keep intact my OS work.
  F6 (for all usb drivers) is not available to boot OS, sorry.

  "cloned" drive is in line with the correct name of made in the BIOS. "Cloned" secondary drive works (with old primary school). How to get access to the new primary OS and loading cloned? Please, any ideas?

  Thank you.

  Hello

  I think that the system cannot boot to the new HARD disk as the partition where the system is installed, was not marked as bootable system partition.

  I recommend to insert the previous HARD drive and to start the laptop.
  HARD drive new, cloned could be connected as an external HARD drive to a USB port.

  Then you should go to disk management (right click my computer - manage-> management-> disk management computer)
  Here you can see the HARD internal disk and the 2nd HARD drive connected to the USB port
  Right-click on the partition (2nd HARD drive) where the Win XP has been installed and choose the partition as the system partition and mark it as active.

  Then you could change the HARD drive again and could power the device in place. Usually, the system should boot to the top of the new marked system partition.

• Qosmio G30 - blue screen of death

  recently I had this error on a blue screen when starting my pc (I can't go in either safe mode) so I decided to start from the cd and repair the system, but the problem is I can't boot from the cd or a port USB of my laptop Qosmio g30... the problem is that I tested the cd on my friends pc and it booted from it mine shows the following message
  "During initialization and the link...".

  PXE - E61: Media test failure, check cable
  "PXE - MOF: exit Intel Boot Agent.

  I really need help here and I don't like the data on my c drive, so if there is no solution I would appreciate

  Thanks in advance.

  Which CD you want to use for BONE repair?

  Akuma is right. This message occurs if the laptop can not boot from optical disc or HARD disk drive. Then automatically seek next boot device and it's LAN. This message is typical for the start of LAN (cable not connected).

• Qosmio G30 - black screen on external monitor

  Qosmio G30 (PQG32E) under Vista Home Premium, driver NVIDIA GeForce Go 7600, 7.15.10.9813

  I can't get a picture on a monitor external (I tried two different monitors). More precisely:

  "Windows Mobility Center" will recognize that a monitor is connected
  "NVIDIA Control Panel - Display Change Configuration" will recognize the external monitor ('Select poster that you want to use' shows 'Display of the laptop + Sony SDM-HS73', which is the monitor plugged in ext)
  but no matter what configuration I try using Fn + F5 or change of display Configuration, I can't do anything but a black (backlight) display on the external monitor.

  The monitor is receiving a video signal correctly: when he is off in laptop only the setting Fn + F5, it displays a warning 'no signal', but when turned on again I just get black.

  I tried to change the resolution for the external monitor settings. They exactly match the native resolution of the monitor. Still nothing.
  I tried 'Clone' and 'Dual View' mode.
  Tried various different orders to turn on the computer laptop and monitor, Plug and unplug the device, etc.

  Having installed the latest driver for the Toshiba (see above) site. Have NOT tried to install any other driver from NVIDIA site, as she warns to use Toshiba - but that's worth a try?

  The clean laptop screen and all other aspects of the video are very good.

  It worked ok in the past (I think that before I did the upgrade to Vista when it was still on XP).
  Should I just wait for another update of Toshiba driver and maybe Vista SP1?

  I really hope this isn't a hardware problem, because the monitor is recognized etc...

  Jonathan

  What port you used?
  The (analog) external monitor port or the output port D-video?

  View as far as I know that if you used the external monitor (analog) port, then you should choose analog in the nVidia-> current view

  Then, you can use the FN + F5 key to switch between the two views.

• Hi, my PC does not start, it displays a screen with lines and then turns black and that of it, can you help me?

  Hi, I have a Compaq Presario C700 no problems so far. It will not start when I turn it on the screen with criss cross lines and then a vertical black line, it turns black and then that's all. ? If I turn on and off for a couple of hours it starts? Can you please help.

  Hello

  Looks like a hardware problem. Contact the seller and the Compaq Support. As Compaq OEM
  is responsible for the functioning Windows and hardware.

  Compaq - support, drivers and documentation online
  http://www.Compaq.com/country/cpq_support.html

  Compaq (HP) - Forums
  http://h30434.www3.HP.com/PSG/|

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• white screen with lines

  I came here because I believe that it is a combination of several mistakes, I don't know.

  When I start the computer in Standard Win2k3, it gives me a white screen with Vibrio black vertical lines across on the screen, with a few horizontal. After some tests, I want to pretend it works, you press Ctrl + Alt + Delete and connected and surprisingly, the computer works - I can see the icon and the load of desk top of the page to the top, BUT the white screen is still there, the bars into brackets upward the desktop icons and the resolution is so low that I only see a small part. Moreover that apparently all workstations had been 'forced' layer on layer on the screen, as I see multiple cursors on the screen all at the same time movement and rhythm (when I move the mouse).

  The next thing that I checked, is since I have installed WinXP, but as if by magic will not work some of my programs (this is why I use it), and the screen has worked very well and very well (with almost nothing, runnable).

  Well, can not compare the two BONES, I also started Win2k3 in safe mode, safe mode with blah, all three cases of Safe Mode gives me good screen and access my programs no internet as safte mode blocks.

  I want my internet back AND my good old Win2k3. If anyone can help. It should not be a video card problem because (1) I have integrated a video card AND (2) it works well under XP

  It could be a corrupted RAM, even if dxdiag shows all the available RAM, I have hope that there is a way to check WITHOUT removing them from the socket.

  It might even be a mistake of an operating system, that I don't know how to make sure that, if I can reinstall after the top in Mode safe

  It could be another thing and combinations of these. (Probably the 2 above, in my view, have no idea how can ensure me that)

  Hello

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the Windows server on TechNet. Please ask your question in the TechNet Windows Server Forums. You can follow the link below to ask your question: http://social.technet.microsoft.com/Forums/en-US/category/windowsserver

• Qosmio G30-126 - problem with the start screen

  My laptop was working perfectly until I suddenly found starting with sound activation boot but without any image appearing on the screen until I got the windows login page in which the image appeared with its normal perfect resolution.

  The operating system is Windows 7, which worked smoothly, with all the drivers toshiba, installed more than 3 months, and the device was normally closed the time before the problem occurred.

  I tried to use the restore disc but the problem is that I can't see something! the computer works, but the screen is black as if the laptop is turned off completely.

  I tried to connect an external one LG LCD but it gave no results, but only a screen empty.

  I really need help in this issue that this notebook contains all of my work and I very much count on it.

  Hello

  Can enter you the BIos (F2 on startup)?

  > I tried to connect an external one LG LCD but it gave no results, but only a white screen

  However, I think it is the dysfunction of the graphics card as your laptop work without any image that appears. In this case, you must contact the ASP (SAV) in your country:

  http://EU.computers.Toshiba-Europe.com/innovation/generic/ASP_SUPPORT/

• Qosmio G30 white screen when you start Windows XP

  Hi everyone - first time poster here!

  Today I turned on my Qosmio Toshiba G30 as I normally do, except that this time, the screen remained blank. Normally, the start of Qosmio screen appears with the music of Qosmio, but only Qosmio music out... no image on the screen! The computer continues to boot properly, but nothing has been posted.

  I panicked and I thought I'd need to buy a new computer...

  While I was on the phone with a friend to a support, I pressed the "TV Out" button (found in the upper right corner). That's it - the screen turned on, but all my icons have been reorganized.

  I tried to reinstall the display driver, but this is still the case every time that I reboot. The problem occurs not when putting the computer to sleep and look upwards again.

  Any help would be much appreciated!

  Thank you...

  Hello

  Check if the video output has not been set for external monitor or TV.
  You can change this by using the FN + F5 key combination.

  I also recommend to connect an external monitor to the laptop.
  Maybe you have defined somehow (accidentally) the external display as the primary display?  :|

  However, you are using Win XP as I m wrong not the laptop has been pre-installed with Vista. (is it true?)
  Maybe you should take a recovery disk Toshiba and must be reinstalled the self-image of Toshiba.

• Re: Qosmio F - flashing screen with AC adapter / CC

  Hello

  I have a problem with the fo my qosmio screen. When turned on ca it flashes when it is not only with the battery.
  Do you think that this is a problem with the adapter only?

  Thank you
  Panas

  Hi panas,

  If this happens with the AC adapter / CC only he could be a grounding problem. Are you using the original Toshiba AC/DC adapter or the adapter part 3?
  By the way: laptop Qosmio what you have exactly?

  This also happens if you connect an external monitor or only with an intern?

• Qosmio G30 - black screen on startup

  Hello

  Having problems with my G30 at startup. I was watching TV using the media library (by pressing the shortcut of the TV next to the power button), but when I tried to reboot the system (by pressing the power button) all I get is a black screen! I hear the sounds of start and the hard disk icon flashes but I don't see anything. Suggestions welcome!

  Neil

  Hello

  Have you tried to connect the laptop to the external monitor to check if something appears on the second screen?
  I think that you should do this. In addition, you can try to use the FN + F5 key combination to switch between the two views.

  If this is not enough and you still won't be able to see anything, I assume that there is a serious hardware problem.

  In this case you should always contact the ASP in your country because in my opinion the simply, common laptop user would not be able to know what's exactly wrong because of the lack of experience and the necessary tools.

  Good luck

• Display Latitude E6510 does not. White screen with lines

  I was working on my Dell Latitude E6510 normally and after I finished I stopped him. I go to the city for about 2 hours and when I got home, I press the power button / stop and suddenly the screen is white with a few scratches on the side. Tried to feed him several times, nothing. Reconnect AC, battery, RAM, HARD drive, peripherals, still nothing.

  Output DisplayPort works without any problem.

  Output VGA works without any problem.

  You can see the pictures and the link to the video on YouTube of this problem.

  Any help or advice? Would be very grateful. Thank you.

  YouTube - Dell Latitude E6510 screen does not, lines, stripes, white

  

  I hope this helps. I have a Latitude E5410 I bought knowing that the LCD screen has a white screen or white veil or a matter of contrast high. I checked that the entire screen removable Panel or it deforming slightly likely to prevent the white veil to disappear, leaving me with a normal display. But I had to "hold my mouth just as it should be" OR I could lose visibility and I Whiteout reappear. I did troubleshooting from the LCD cable connection to the motherboard. I removed the cover of the LED/hinge and screws of the keyboard. I started the computer and put in the Setup (BIOS). After that I got the content of the screen, I removed the keyboard and waved the LCD cable connector. It was nice sitting. I replaced the keyboard and remove the bezel before display. I waved the display cable DC7TY to the small LED Council, but that did nothing. I turned off the computer.

  I unscrewed the 6 screws holding brackets LCD panel and hinge for the lid of the display, exposing the back of the display panel itself. On the right side, low on the Panel, I peeled back the glue 1/4 x 3/8 on the clear plastic covering the printed circuit board, exposing the flex cable going to the backlight. I spilled Brown lever that keeps the flex cable plugged into the connector on the plug, removed the cable, he moved several times to repeat, then hit the lever to keep it. With the LCD in this way exposed, I started the computer and entered in the Setup program. SUCCESS!  No amount of stirring or warping brought Whiteout. I've buttoned to the computer and came here for successful results.

  Your Dell may be different, but you can report if your symptoms or the results are different, and HOW EXACTLY became you a success. See you soon!