question about #show ip arp in cisco 2960 g switch!

Similar Questions

• Gateway to Comcast Business class SMCD3G-CCR and Cisco 2960 G switch

  Hello

  I'm looking to upgrade my silent switches to a Cisco 2960 switch.  I wanted to check and make sure that this configuration would be funded.

  I need to configure the 4 VLANS on Cisco 2960 switch, 1 for the vmotion traffic, which would have no internet access, one for management traffic that does not have internet access, for standard server traffic and traffic vmserver, who should access to the internet.

  The Cisco switch working with gateway SMCD3G-CCR ok, or do I need another router for this?  If yes why?

  I don't know if this is the right forum but I know that Cisco linksys bough, so I hope someone can point me in the right direction.

  Thank you

  Hello.

  These products are processed by the Cisco Small Business Support Community.

  * If my post answered your question, please mark it as "acceptable Solution".

  Thank you!

• a question about upgrading memory CF for Cisco 3745

  As we know, the cisco 3745 has 2 locations CF. memory One is internal with a 32 MB of memory by default CF card, another one is external.

  My question is:

  1 is the same as the internal memory card CF CF external memory card?

  2. If I choose the upgrade of the plant CF memory from 32 MB to 128 MB, which slot will be used? Cisco remove the memory of 32MB CF card and install a new 128 MB card in the internal slot or simply add an additional CF memory card through the outside slot?

  Thank you!

  Hello

  the reference for the internal and external numbers are different, which suggests that they are not compatible. So you will have to specify what you want to, for example, MEM3725-32U128CF (which is the internal upgrade) or MEM3725-128CF-EXT (which is the external upgrade).

  In all cases, internal and external cards are not cumulative, in order to get e.g. 128 MB flash, you must either internal, or external card with these 128 MB:

  Q. can partition you the internal Cisco 3700 Series Compact Flash card and the card Compact Flash external to combine or separate them?

  A. No, you cannot join two separate Compact Flash cards or you can their partition.

  HTH,

  GP

• Question about my first payment of cisco ISE

  Hi, thanks in advance,

  It's my first time to be implemented cisco ISE 1.1.4 with Vmware Esxi v5.5

  I did so far process

  -Created NTP, DNS, AD, of course ESXI running and have link between each other, ISE is able to synchronize the time with ntp server and DNS, etc AD.

  -J' created repository for installation of application bundle - which is ise-appbundle - 1.1.4.218.i386 that I could not find any fault of the application.

  However, while I was doing installation and it said ' / opt/oracle/base/product/11.2.0/dbhome_1/bin/lsnrctl: error while loading shared libraries: libclntsh.so.11.1: cannot open shared object file: no such file or directory "."

  I already check some forums and communities, and I have no problem about synchronizing time on dns with ntp and ISE itself with ntp.

  I have no firewall between devices and no other network devices don't interfere.

  and at the end of newspapers, it comes up like this

  ########################################################################################

  ERROR: CANNOT START DB!

  Database is not available in 240 seconds Timeout.

  This could be the result of incorrect network interface configuration

  or the lack of resources on the device or the virtual computer. Please solve the problem, run the following CLI to start the database again:

  "reset - config application ise"

  ########################################################################################

  Im just lost now... Any recommendation?

  Well, it is true that the CCIE Security use ISE 1.1 as its base. So for the installation of laboratory only for this purpose, you might go with him.

  90% of the things are similar and the concepts are identical to 1.1 to 1.3. The first versions were buggy however and we recommend to all production users go with 1.3.

  A new installation of 1.14 should be OK; but you would not use the Archives of gz appbundle ISE - you need to use the new installation ISO.

  Please see screenshot below.

  ise_1.1.4_packages.PNG

  

• LAPAC1750PRO & Cisco 2960-S - LACP issues Switch

  Hello community,

  I currently have a layer 2 Cisco 2960-S switch. It has 48 port Gigabit Ethernet ports and 4 SFP ports. I have Setup 3 VLAN on the switch VLAN 10, 11, 255. VLAN 10 is for my home equipment, VLAN 11 for my Audio/video/server equipment and VLAN255 is my network of comments. It's all behind a normal router from D-Link 4 port every day. All correctly connected working processes.

  I have the LAPAC1750PRO access point, I went ahead and ran 2 Cat6 cables so I could take advantage of the link aggregation 802.3d of the Access Point. I configured the passage from what I can tell properly. The problem is that when I turn on the two links AP causes beating port and stop passing traffic. If I disable the second link (leaving the active primary link) everything is stable. Speed is decent on my laptop, and from my iPad, it's fantastic.

  Does anyone have experience using the Protocol LACP (link Aggreagtion 802.3d) with this Access Point? I really want to use this so I can get 2 Gbps throughput of this device to my other devices.

  I'll be happy to post my Cisco Configuration so if someone is paid enough in that as well.

  Thank you

  Jason

  Senior Network Engineer

  OK - I thought about it. He was not at all a problem with the switch or my setup. This is the problem...

  Here's the question – and how I fixed it.

  1 cisco switch - Configuration:

  !

  GigabitEthernet1/0/1 interface
  switchport access vlan 10
  switchport mode access
  spanning tree portfast
  channel-group mode 1 on

  !

  interface GigabitEthernet1/0/2
  switchport access vlan 10
  switchport mode access
  spanning tree portfast
  channel-group mode 1 on

  That's right - this force LACP on the unit and do not have to worry about negotiating/connections protocols.

  2. access point - if it is already configured - factory reset the unit. LACP must be enabled during active keybord with DHCP boot. After that you can configure it as you want.

  What I had to do so was by default the access point and let it be starting with LACP rebuild - I wonder if this is due to something in the firmware that, once the NIC is configured, they become hardcoded and do not change to different settings?

  Whatever it is - this problem is solved.

• Switch Cisco 2960/3560 = > recovery password and default settings with the button Mode

  Hi Experts,

  I have some confusion with the button Mode with cisco 2960/3560 switches.

  I read on many forums and articles, but where things are not clear.

  a place given 3 seconds and somewhere is given 7 or 10 seconds.

  Qus1), what is the exact time to press/hold Mode button to perform two following tasks:

  A. password recovery (according to my knowledge 3 sec) good or bad?

  Configuration of the switch (start + run) would be safe

  After the recovery of password? Yes or no

  B. factory default (according to my knowledge 10 dry) good or bad?

  I'm afraid, because if I press mode button more than 3 seconds, then

  It will delete any configuration of cisco switch. Yes or no

  Qus2) I want to recover the catalyst 2960/3560 switch password without

  Start/run configuration to lose. That is my main concern.

  Please tell me how to do this, what will be the time keeping Mode buttom

  in a few seconds?

  Qus3) which means this line

  "If the password recovery mechanism is disabled in switch

  then you will lose all the config.

  This sentence has been given on this forum url

  https://supportforums.Cisco.com/thread/140848

  KS

  Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) port console switch.

  Use the following terminal settings:

  • Bits per second (baud): 9600

  • Data bits: 8

  • Parity: None

  • Stop bits: 1

  • Flow control: Xon/Xoff

  Note: For more information on the wiring and connection of a terminal to the console port, refer to connecting a Terminal to the Console Port of Catalyst switches.

  Unplug the power cable.

  The power switch and take it to the switch: command prompt:

  2900XL, 3500XL, 2940, 2950, 2960, 2970, 3550, 3560, and 3750 switches of the series, to do this:

  Press and hold the mode button located on the left side of the façade, while you reconnect the power cable from the switch.

  2960, 2970

  Release the Mode button when the SYSTEM LED flashes orange and then turns green. When you release the Mode button, the SYSTEM LED flashes green.

  3560, 3750

  Release the Mode button after about 15 seconds when the SYSTEM LED turns green. When you release the Mode button, the SYSTEM LED flashes green.

  The system was interrupted before the flash at the end file system initialization

  loading the operating system software:

  flash_init

  load_helper

  boot

  switch:

  Run the flash_init command.

  switch: flash_init Initializing Flash... flashfs[0]: 143 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 3612672 flashfs[0]: Bytes used: 2729472 flashfs[0]: Bytes available: 883200 flashfs[0]: flashfs fsck took 86 seconds ....done Initializing Flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 switch: !--- This output is from a 2900XL switch. Output from !--- other switches will vary slightly.

  Run the load_helper command.

  switch: load_helper switch:

  Question the dir flash: command.

  Note: Be sure to type a colon ":" after the dir flash.

  Appears in the file system of the switch:

  switch: dir flash: Directory of flash:/ 2    -rwx  1803357                  c3500xl-c3h2s-mz.120-5.WC7.bin !--- This is the current version of software. 4    -rwx  1131                     config.text !--- This is the configuration file. 5    -rwx  109                      info 6    -rwx  389                      env_vars 7    drwx  640                      html 18   -rwx  109                      info.ver 403968 bytes available (3208704 bytes used) switch: !--- This output is from a 3500XL switch. Output from !--- other switches will vary slightly.

  Type rename flash: flash: config.old config.text to rename the configuration file.

  switch: rename flash:config.text flash:config.old switch: !--- The config.text file contains the password !--- definition.

  Issue the boot command to boot the system.

  switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC7.bin"...############################### ################################################################################ ###################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC7.bin" uncompressed and installed, entry po int: 0x3000 executing... !--- Output suppressed. !--- This output is from a 3500XL switch. Output from other switches !--- will vary slightly.

  Enter "n" at the prompt to abort the initial configuration dialog box.

  --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Continue with configuration dialog? [yes/no]: n !--- Type "n" for no. Press RETURN to get started. !--- Press Return or Enter. Switch> !--- The Switch> prompt is displayed.

  At the switch prompt, type en to enter a mode.

  Switch>en Switch#

  Password recovery

  Type rename flash: config.old flash: config.text to rename the configuration file with its original name.

  Switch#rename flash:config.old flash:config.text Destination filename [config.text] !--- Press Return or Enter. Switch#

  Copy the configuration file in the memory.

  Switch#copy flash:config.text system:running-config Destination filename [running-config]? !--- Press Return or Enter. 1131 bytes copied in 0.760 secs Sw1#

  The configuration file is now reloaded.

  Replace the current passwords that you do not know. Choose a password with at least one capital letter, one number and one special character.

  Note: Replace passwords that are required. You must crush not all passwords listed.

  Sw1# conf t !--- To overwrite existing secret password Sw1(config)#enable secret !--- To overwrite existing enable password Sw1(config)#enable password !--- To overwrite existing vty password Sw1(config)#line vty 0 15 Sw1(config-line)#password Sw1(config-line)#login !--- To overwrite existing console password Sw1(config-line)#line con 0 Sw1(config-line)#password 

  Write the running configuration in the configuration file with the write memory command.

  Sw1#write memory Building configuration... [OK] Sw1#

  For factory reset:

  do not give under the control of factory reset

  Switch#copy flash:config.text system:running-config

  can I copy the running configuration to Flash

  Switch flash running-config #copy:

  Destination file name [running-config]?

  Building configuration...

  [OK]

  Switch #copy running-config startup-config

  Name of destination file [startup-config]?

  Building configuration...

  [OK]

  Review the link for more information below

  http://www.Cisco.com/en/us/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

  Please note the useful messages.

  Concerning
  Vesta
  "Everybody is genius." But if you judge a fish by its ability to climb on a tree, he will live his entire life, believing that this is stupid. "

• Cisco Catalyst 4503-> Cisco 3560 L3-> Cisco 2960 L2-> Cisco SMB switch

  Hi Experts,

  I am trying to add a Cisco SMB SF300 - 24 Switch to an infrastructure that has only the Cisco Catalyst switches

  The base layer is Cisco Cataylst 4503. Distribution is Cisco Catalyst 3560 and Cisco 2960 switches access layer.

  There are about 30 VLAN present in the infrastructure that is announced to all switches using VTP. Inter VLAN routing takes place at basic switches

  by creating the Interface VLAN for each VLAN of L2.

  1. the new 150 VLAN must be created on the new Cisco SMB switch. If I create a corresponding interface 150 VLAN on core switches, it will forward the other VLANs traffic just as he is currently working for Cisco 2960 Catayst switches?

  2. While they inspected, I could see that the DERIVATIVE is not supported on the Cisco SMB switches and I would need to go GVRP if I need to make advertising information to other switches VLAN. But since GVRP is only supported on CatOS and there is no inter operability between GVRP and DERIVED, I would need to manually create the VLAN on the new switch. Is this correct?

  Help, please!

  Thank you very much

  ANUP

  Good afternoon Anup Sasikumar

  Please use our forum

  My name is Johnnatan I am part of the community of support to small businesses, I saw your post and I understand that you want to configure VTP and GVRP.

  I'm afraid you will have to configure it manually each Vlan in each device CatOS GVRP, in order to keep their databases vlan in sync. As you say, VTP is support it not in CatOS

  You can try to connect the two protocols, but I encourage you do not follow this procedure.

  On your question about intervlan routing, if you create a corresponding interface 150 VLANS on switches to base it is routed, if your configuration is correct (port access, ports of junction, intervlan etc..)

  I hope that you will find this answer useful, if it was satisfactory to you, please indicate the question as answer.

  Please evaluate the useful messages.

  Greetings,

  Johnnatan Rodriguez Miranda.

  Support of Cisco network engineer

• Question about slide show

  Hi all, I have a question about slide show. How can I make these sideshow with active text and the button. For example the homepage * .ebinger - canvas.co.UK

  Thank you.

  Sergiy salvation,

  You can select the target of a slide show window and make a hyperlink and resize it.

  Kind regards

  Akshay

• Question about warranty after exchanges of RAM on Satellite module series

  Hello together,

  I have a question about the warranty. My laptop is 5 months old and now I want to improve it with more RAM. I want to do it myself, and now I'm wondering if the warranty will be getting hurt.
  Thanks in advance for your answers.

  Concerning

  TiG3r

  For new models of laptops the RAM upgrade described in s operating manuals. It is public act and it shows the owner of the notebook how do RAM upgrade only.

  If Toshiba offers something like this he won't have the negative influence of valid warranty.
  Buy a compatible module and RAM upgrade.

  Bye and good luck!

• Qosmio E10: Question about PX1211E-1TVD Toshiba DVB - T USB Tuner

  Hey all,.
  While the analog TV tuner that is inside my Qomsio E10 is OK for now, I'm looking forward to get a Digital Tv Tuner USB from Toshiba adapter.

  HTTP://UK.COMPUTERS.TOSHIBA-EUROPE.COM/CGI-BIN/TOSHIBACSG/INDIVIDUAL_OPTIONS_PAGE.JSP?SERVICE=UK&ACTION=SHOW _ATTRIBUTES & OPTION_ID = 109331

  And I have 2 questions about this article on Qomsio:

  1 MCE (version 2004 on E10) will be able to use this DVB - T Tuner for me to record digital programs in MCE?

  2 "Intervideo WinDVD Creator 2 Platinum for Toshiba" (comes with E10) will be able to see the PX1211E-1TVD so?

  If not, what software could be used to record DVB - T programs?
  Later,.

  Alcahest

  Hi Alex

  You will be very happy if someone can give you a precise answer to your questions. I didn't see this before, but it will be interesting to know if it works with my Tecra laptop.

  If seek you information please let me know how it works. Thank you!

• Questions about TV Tuner Satellite A500/040

  Hi all

  I'm new to the Tuner of TV analog digital hybrid and I'm sorry if my questions seem as stupid.

  I have two questions about the of digital TV Tuner analog integrated hybrid in the Notebook Toshiba Satellite A500/040. My understanding is that the TV tuner hybrid integrated able to decode TV signals high definition and their display on TV via its HDMI port. I wonder if I could watch TV shows on your laptop without connecting to a TV. If so, is the software needed? There are several USB TV tuners for desktops and laptops on the market, A500 hybrid TV tuner works differently these USB TV tuners?

  Thank you

  Young

  > I think I know that the TV tuner hybrid integrated able to decode TV signals high definition and their display on TV via its HDMI port.

  N ° this s tv tuner not a HD!
  It s a digital tuner that provides digital video signal 576i and not 1080i.

  Of course, you can use the HDMI port to connect the laptop to the LCD HDMI port but you will not get the quality video full HD as blueray for example.

  I found this Australian page from Toshiba:
  http://www.MyToshiba.com.au/products/notebooks/satellite/A500/psam3a-04000e

  You will find this passage short text:
  + With tuner TV built-in, you can even watch analog or digital TV everywhere where you travel, while the HDMI ports make connecting high definition on your TV screen and sound system. +

  You can also watch TV on mobile phones display! It's a key reason why the TV tuner built in ;)

• Re: Several questions about the recovery of the Satellite L750 features

  I have several questions about the recovery of Satellite L750 features available to it. Any help and answers would be useful.

  (1) when I started the laptop first, he asked me to create a recovery CD incase I need to reinstall the operating system. But he also said that he built in the recovery partition, so therefore, I have to make a recovery cd or not?

  (2) will be the recovery CD is exactly the same as the recovery on the system partition?

  (3) is the partion of CD or recovery includes all the integrated software pre-installed with the laptop?

  (4) also in the device manage management it shows watch partion recovery but it is empty, is it true?

  (5) in the second partition (drive D) system, he has a record with what looks like the recovery of files and folders. Is it safe to move/remove it?

  Hello

  I'll try to provide answers:
  1 - to ensure that everything works perfectly you don t need these discs, but if something goes wrong with the HARD drive you will not be able to do anything. When you have the recovery DVDs, you will still be able to install the recovery image and once again the factory settings. So my advice to you is: create these discs as soon as possible. Use only on DVD-R media and buy products of high quality (TDK or Verbatim).
  2 - Yes.
  3 - Yes.
  4 - No. Don t be confused with this.
  5. in a first time create restore DVD, and later you can do what you want. I put t know which files mean you but don t touch anything before that of the recovery disks to be created.

  In the past, many people have been experimenting with the structure of HARD drive and partitions and later was surprised when installing disk recovery HARD has been damaged. Don t make the same mistake.

  If you have any other questions you are welcome.

• 2 questions about mcupdate.exe

  Use Vista Home Premium 32-bit with SP2 of Vista on HP desk top of page

  2 questions about mcupdate.exe

  1. what is? When I google it I get's things on McAfee. I have McAfee and never had McAfee. The information google seems to indicate that it could be a virus. However, I see the following

  -It seems to be in the ehome on my computer folder

  -It seems it works twice a day and every time it turns my internet connection log shows the connection to a microsoft ip address for 'download tv' or something like, think if it is not not a virus

  2 seems that it does not always work. I'll get these connections every day, twice a day for a few weeks or more, then get not every day.

  Currently I seem to not get any activity, just after the silver light updated 01/09/10. I do not use the TV feature on my computer, but I was wondering what it is and why it works sometimes

  Hello

  The link works here even if it could be glitch or malware, if you can access a Microsoft site. Try
  Yet once, and if no joy don't try to see if you can reach http://www.microsoft.com

  The 2nd link describes the file unless it has been replaced by malware here is information.
  Would that be a normal update.

• Question about the differences in commands

  Hey guys -.

  I just had a few questions about the differences between orders that seem to perform the same function.  Can you let me know if an order is more preferable to the other and what the difference is.  I would really appreciate it as it I currently practice some INE laboratories and I see that orders change from lab to lab.  Thanks advance!

  1. When you write a static NAT for specific host 1 - is - this important if I understand the 32 subnet?

  EX: static (inside, outside) 1.1.1.1, 2.2.2.2 VS static (inside, outside) 1.1.1.1 2.2.2.2 netmask 255.255.255.255

  2. when I'm setting up a router as a CA server and it is necessary to "export" the key, whatever my method of exporting the key?  If so, in which method call for which solution?

  EX: key export cryptographic rsa ciscox pem URL nvram: cisco VS. exporting key 3des cryptographic ciscox pem 3des rsa terminal cisco

  3. If I have to mark a packet with a DSCP of X value, matter if I use the 'set dscp' VS 'set ip dscp?  If so, what is the difference?

  FXY

  Policy-map X

  class X

  the dscp X value

  VS

  Policy-map X

  class X

  X ip dscp value

  I guess pertaining to 2, if i was speaking in terms of from a cisco router to another cisco router - would terminal be acceptable?
  
  

  Yes, the "Import cryptographic key" command can take a url and also from the terminal entrance. In this terminal case wil is much easier.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• Questions about drawText.

  Hi experts,

  I have two questions about drawText:

  (1) we have function to set the font of the text, is it possible to define the font size? or it is based on the current theme?

  (2) where the text is longer than the clipping region, I would like to show «...» "signal at the end of the sentence. Is this possible or do us it manually?

  I tried to use setDrawingStyple (DrawStyle.ELLIPSIS, true) before drawing text, but nothing changes.

  Thank you

  Binh Nguyen

  Hello

  You can set the font size, something like that

  FontFamily ff.;
  FF = FontFamily.forName ("BBMillbankTall");
  smallB = ff.getFont (FontFamily.SCALABLE_FONT, 15) .derive (Font.BOLD);

  As for your second question, you can use the DrawStyle.Ellipses property

  Let me know if this helped you or not.