LAPAC1750PRO & Cisco 2960-S - LACP issues Switch

Similar Questions

• Switch Cisco 2960/3560 = > recovery password and default settings with the button Mode

  Hi Experts,

  I have some confusion with the button Mode with cisco 2960/3560 switches.

  I read on many forums and articles, but where things are not clear.

  a place given 3 seconds and somewhere is given 7 or 10 seconds.

  Qus1), what is the exact time to press/hold Mode button to perform two following tasks:

  A. password recovery (according to my knowledge 3 sec) good or bad?

  Configuration of the switch (start + run) would be safe

  After the recovery of password? Yes or no

  B. factory default (according to my knowledge 10 dry) good or bad?

  I'm afraid, because if I press mode button more than 3 seconds, then

  It will delete any configuration of cisco switch. Yes or no

  Qus2) I want to recover the catalyst 2960/3560 switch password without

  Start/run configuration to lose. That is my main concern.

  Please tell me how to do this, what will be the time keeping Mode buttom

  in a few seconds?

  Qus3) which means this line

  "If the password recovery mechanism is disabled in switch

  then you will lose all the config.

  This sentence has been given on this forum url

  https://supportforums.Cisco.com/thread/140848

  KS

  Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) port console switch.

  Use the following terminal settings:

  • Bits per second (baud): 9600

  • Data bits: 8

  • Parity: None

  • Stop bits: 1

  • Flow control: Xon/Xoff

  Note: For more information on the wiring and connection of a terminal to the console port, refer to connecting a Terminal to the Console Port of Catalyst switches.

  Unplug the power cable.

  The power switch and take it to the switch: command prompt:

  2900XL, 3500XL, 2940, 2950, 2960, 2970, 3550, 3560, and 3750 switches of the series, to do this:

  Press and hold the mode button located on the left side of the façade, while you reconnect the power cable from the switch.

  2960, 2970

  Release the Mode button when the SYSTEM LED flashes orange and then turns green. When you release the Mode button, the SYSTEM LED flashes green.

  3560, 3750

  Release the Mode button after about 15 seconds when the SYSTEM LED turns green. When you release the Mode button, the SYSTEM LED flashes green.

  The system was interrupted before the flash at the end file system initialization

  loading the operating system software:

  flash_init

  load_helper

  boot

  switch:

  Run the flash_init command.

  switch: flash_init Initializing Flash... flashfs[0]: 143 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 3612672 flashfs[0]: Bytes used: 2729472 flashfs[0]: Bytes available: 883200 flashfs[0]: flashfs fsck took 86 seconds ....done Initializing Flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 switch: !--- This output is from a 2900XL switch. Output from !--- other switches will vary slightly.

  Run the load_helper command.

  switch: load_helper switch:

  Question the dir flash: command.

  Note: Be sure to type a colon ":" after the dir flash.

  Appears in the file system of the switch:

  switch: dir flash: Directory of flash:/ 2    -rwx  1803357                  c3500xl-c3h2s-mz.120-5.WC7.bin !--- This is the current version of software. 4    -rwx  1131                     config.text !--- This is the configuration file. 5    -rwx  109                      info 6    -rwx  389                      env_vars 7    drwx  640                      html 18   -rwx  109                      info.ver 403968 bytes available (3208704 bytes used) switch: !--- This output is from a 3500XL switch. Output from !--- other switches will vary slightly.

  Type rename flash: flash: config.old config.text to rename the configuration file.

  switch: rename flash:config.text flash:config.old switch: !--- The config.text file contains the password !--- definition.

  Issue the boot command to boot the system.

  switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC7.bin"...############################### ################################################################################ ###################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC7.bin" uncompressed and installed, entry po int: 0x3000 executing... !--- Output suppressed. !--- This output is from a 3500XL switch. Output from other switches !--- will vary slightly.

  Enter "n" at the prompt to abort the initial configuration dialog box.

  --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Continue with configuration dialog? [yes/no]: n !--- Type "n" for no. Press RETURN to get started. !--- Press Return or Enter. Switch> !--- The Switch> prompt is displayed.

  At the switch prompt, type en to enter a mode.

  Switch>en Switch#

  Password recovery

  Type rename flash: config.old flash: config.text to rename the configuration file with its original name.

  Switch#rename flash:config.old flash:config.text Destination filename [config.text] !--- Press Return or Enter. Switch#

  Copy the configuration file in the memory.

  Switch#copy flash:config.text system:running-config Destination filename [running-config]? !--- Press Return or Enter. 1131 bytes copied in 0.760 secs Sw1#

  The configuration file is now reloaded.

  Replace the current passwords that you do not know. Choose a password with at least one capital letter, one number and one special character.

  Note: Replace passwords that are required. You must crush not all passwords listed.

  Sw1# conf t !--- To overwrite existing secret password Sw1(config)#enable secret !--- To overwrite existing enable password Sw1(config)#enable password !--- To overwrite existing vty password Sw1(config)#line vty 0 15 Sw1(config-line)#password Sw1(config-line)#login !--- To overwrite existing console password Sw1(config-line)#line con 0 Sw1(config-line)#password 

  Write the running configuration in the configuration file with the write memory command.

  Sw1#write memory Building configuration... [OK] Sw1#

  For factory reset:

  do not give under the control of factory reset

  Switch#copy flash:config.text system:running-config

  can I copy the running configuration to Flash

  Switch flash running-config #copy:

  Destination file name [running-config]?

  Building configuration...

  [OK]

  Switch #copy running-config startup-config

  Name of destination file [startup-config]?

  Building configuration...

  [OK]

  Review the link for more information below

  http://www.Cisco.com/en/us/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

  Please note the useful messages.

  Concerning
  Vesta
  "Everybody is genius." But if you judge a fish by its ability to climb on a tree, he will live his entire life, believing that this is stupid. "

• Gateway to Comcast Business class SMCD3G-CCR and Cisco 2960 G switch

  Hello

  I'm looking to upgrade my silent switches to a Cisco 2960 switch.  I wanted to check and make sure that this configuration would be funded.

  I need to configure the 4 VLANS on Cisco 2960 switch, 1 for the vmotion traffic, which would have no internet access, one for management traffic that does not have internet access, for standard server traffic and traffic vmserver, who should access to the internet.

  The Cisco switch working with gateway SMCD3G-CCR ok, or do I need another router for this?  If yes why?

  I don't know if this is the right forum but I know that Cisco linksys bough, so I hope someone can point me in the right direction.

  Thank you

  Hello.

  These products are processed by the Cisco Small Business Support Community.

  * If my post answered your question, please mark it as "acceptable Solution".

  Thank you!

• Cisco Catalyst 4503-> Cisco 3560 L3-> Cisco 2960 L2-> Cisco SMB switch

  Hi Experts,

  I am trying to add a Cisco SMB SF300 - 24 Switch to an infrastructure that has only the Cisco Catalyst switches

  The base layer is Cisco Cataylst 4503. Distribution is Cisco Catalyst 3560 and Cisco 2960 switches access layer.

  There are about 30 VLAN present in the infrastructure that is announced to all switches using VTP. Inter VLAN routing takes place at basic switches

  by creating the Interface VLAN for each VLAN of L2.

  1. the new 150 VLAN must be created on the new Cisco SMB switch. If I create a corresponding interface 150 VLAN on core switches, it will forward the other VLANs traffic just as he is currently working for Cisco 2960 Catayst switches?

  2. While they inspected, I could see that the DERIVATIVE is not supported on the Cisco SMB switches and I would need to go GVRP if I need to make advertising information to other switches VLAN. But since GVRP is only supported on CatOS and there is no inter operability between GVRP and DERIVED, I would need to manually create the VLAN on the new switch. Is this correct?

  Help, please!

  Thank you very much

  ANUP

  Good afternoon Anup Sasikumar

  Please use our forum

  My name is Johnnatan I am part of the community of support to small businesses, I saw your post and I understand that you want to configure VTP and GVRP.

  I'm afraid you will have to configure it manually each Vlan in each device CatOS GVRP, in order to keep their databases vlan in sync. As you say, VTP is support it not in CatOS

  You can try to connect the two protocols, but I encourage you do not follow this procedure.

  On your question about intervlan routing, if you create a corresponding interface 150 VLANS on switches to base it is routed, if your configuration is correct (port access, ports of junction, intervlan etc..)

  I hope that you will find this answer useful, if it was satisfactory to you, please indicate the question as answer.

  Please evaluate the useful messages.

  Greetings,

  Johnnatan Rodriguez Miranda.

  Support of Cisco network engineer

• M8024 K-switch Cisco WS - 2960 S-24TD-L switch interconnection

  Hello

  I have 4 ports SFP + Module switch M8024-K. I want to establish connectivity 10Gig between M8024-k and Cisco WS-C2960S-24TD-L switch. I'm not able to find the exact Dell transmitter/receiver part number required for 4-port SFP + Module and cord Patch LC - LC-OFC required dell. I have no problem with Cisco parts.

  Kindly suggest exact reference numbers.

  Jean Marc

  This transceiver is listed on the list of compatibility of the server but not the switch. It can work in the switch, but I can't confirm that it will be because he is not on the compatibility list.

• Cisco 2960, no mail, solid green system switch of death?

  I have 2 - WS-C2960-24TT-L past. Both are facing the same question.

  When they started, all lights are flashing on the indicator panel mode, then it goes directly to a solid green "SYSTEM." Nothing written on the console cable. I tried computers, cables, and different rates of transfer standard. None of the ports developed regardless of how long each switch is powered. The Mode key during boot produced the same result, nothing.

  Looks like they are dead, however, I thought this would be the place to go for ideas. I can relive these switches?

  Nope.  Time for you to contact Cisco TAC and get the RMA - ed devices.

• question about #show ip arp in cisco 2960 g switch!

  Hi, I would ask on sh ip arp in cisco switch,

  If I type show ip arp in cisco switch, it only displays the arp in the vlan 1, although I have a lot of VLAN connected to the PCs and servers, but only it displays the arp of the vlan 1.

  on my switch, I have an IP under interface vlan 1

  How to view the application of all the VLANS?

  concerning

  Hello

  ARP request is sent to neighbors directly connected in the same vlan, for other hosts in vlan that you'll only arp for default gateway entry.

  Kind regards.

  Alain

  Remember messages useful rate.

• LACP y switch virtual Standard

  Hola

  Sabeis if is pueden configurar a virtual standard switch con back tarjetas para as funcionen in el switch fisico configurado con LACP aggregation?

  decir, if tenian el grouping?

  Gracias.

  Hola compañero,

  a Día de hoy solo supports vmware's para el uso en version of vSphere 5.1 LACP solo VDS (VMware vDistributed rocking):

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC&docType=kc&docTypeID=DT_KB_1_1&externalID=2034277

  In the rest of scenarios, para hacer NIC teaming is debe usar (para cisco switch) Etherchannel con el LACP (802.3ad) desactivado. Modo in "static mode WE:

  http://communities.VMware.com/message/902563#902563

  Te dejo par UN of vmware as explican muy KB well el tema of NIC teaming en vSphere:

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC&docType=kc&externalId=1001938&sliceId=1&docTypeID=DT_KB_1_1&dialogID=675078772&StateID=1%200%20675098848

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC&docType=kc&externalId=1004048&sliceId=1&docTypeID=DT_KB_1_1&dialogID=675078772&StateID=1%200%20675098848

  Saludos,

  Pablo

• Lacp on switches speed

  the switch is 2 N4032 with 1 40 g stacking cable. extended frames are not yet activated.

  two r720s of dell with lacp ethernet 10g across the two switches. a ubuntu running 16.04, the other debian with kernel 4.4.6 jessie.

  iperf3 through them shows 8.9 Gbps, which is what I was waiting on a single port. is the gap between the switch slow down to the speed of a?

  Aggregation of links kind of can be considered a road. Adding extra lanes to the highway will pass total number cars that can be on the road and reduce congestion. However, the limit speed of the road remains the same.

  Your results are correct and are the behaviour expected of an OFFSET.

• Cisco TOR <>VTRX R1-2401 switches

  Hello

  It may be OT in a PowerConnect forum but at least it's a switch...

  It's my first modern exhibition switches Dell; but I played a little with Cisco kit.   Then, someone whose had more time on a VRTX me has received indications linking the module _switch_ of a VRTX to a Cisco TOR (C4948) switch?

  The deployment is for ESXi (5.1) and requires several VLANS on the VRTX blades.  There are only half a dozen of VLAN involved so manual definition is not a big deal. Cisco C4948 requires 802. 1 q on the trunk of cisco-style connection to R1-2401.

  Once that the ILO is the question of the internal port (in the face of the blade-server) configuration...

  General or Trunk mode?

  Extracts of any config?

  DRM for pointers...

  D

  Hi Dave,.

  Want to check in with you and see if you were able to get this working?

  Thank you

• How to connect Cisco SG-300-10 L3 switch selector mode in Mode of L2 SG-300-20

  Ladies and gentlemen, please forgive me if you find my question too basic. But, I would really appreciate your help. I have two Cisco switches (SG-300-10 and SG-300-20) and I am struggling to connect with each other.

  Requirements: Switch Cisco SG-300-10 which is in needs of L3 mode to send the traffic of VLAN tagged to the switch Cisco SG-300-20, which is the mode of L2

  What I've done so now

  1 Cisco SG-300-10 (Mode L3) to the router directly connected and configured IP addresses, 192.168.0.21. The GVRP is configured for Port 5. Created the VLAN 1000 with interface IP (192.168.100.1) and configured the Port 5 trunk mode (1U, 1000 t)

  2 connected Cisco SG-300-20 (L2 Mode) to the router and set up the IP address management, 192.168.0.22. The GVRP is configured for Port 5. 1000 of VLANS created and configured the Port 5 trunk mode (1U, 1000 t)

  What does not work

  I can't access the address of management of the L2 (192.168.0.22) switch. Note that the L2 switch only on the uplink, which is to the L3 switch. Since the Port 5 also receives no marked traffic of VLAN1 (192.168.1.1), I'm assuming that he would receive the network management of VLAN1.

  Other Observations

  When I connect the cable between the two switches Port5, I expect to exchange information of VLAN, by documentation. But the lights flash at all.

  I tried other things

  I tried to connect Port 2 (1U) L3 Switch switch 2 L3 Port (1U). Yet, I can't access to the management of the L2 switch port. However, when I connect 2-Port L3 switch to my laptop, I get an IP address. That tells me that I have to solve the problem of management network pair before the switches.

  Hi Späti,

  I think the confusion is the use of the address IP address to you and how you manage your computer.

  VLAN 1 = 192.168.1.1

  VLAN 1000 = 192.168.0.21

  How I read that you connect layer 2 VLAN 1 on 192.168.0.21 switch to layer 3 of the same VLAN 1 interface to 192.168.1.1. It's confusing.

  So first thing to do is this - change layer 2 switch network 192.168.1.x IP and confirm management works on VLAN 1.

  If you want to layer 2 switch works on VLAN 1000, then you need to change the default VLAN 1000, then you can configure your uplink either as the way which you have 1u, 1000 t, or you can use 1000u.

  Your management VLAN on the layer 2 switch is VLAN 1 still unless you changed it (which did you not?)

  A next important thing for the layer 2 switch is going to be the default gateway. The switch of level 3, you need to specify the address IP of the VLAN 1000, which I think you did to 192.168.0.21/24. This 192.168.0.21 must be the default gateway for the layer 2 switch.

  Finally, the computer you connect to layer 3 switch, what that either VLAN that you choose to connect to (1 unidentified), you need to set the IP and default gateway appropriate. So if you're going to VLAN 1 then your computer is 192.168.1.x with gateway 192.168.1.1

  And for the comment extra, GVRP is a horrible Protocol and very pitiful, I don't recommend to use.

• Lacp 3560 switch circuits

  I'm trying to run a trunk on a four port Lacp group to a form of switch netgear a 3560 but am stuck. Everything works fine if I place a chest with a single autonomous port, and that everything works when I use a group of Lacp 'switchport access' mode, but as soon as I activate "switchport trunk" each gi status goes to "suspended" and no traffic flows.

  Does anyone have any suggestions?

  Thank you.

  Andrew,

  Thank you for the additional information. The configuration of the ports seems to be ok now.

  After the Show etherchannel , physical ports are individual-State. This would mean that the switches did not negotiate the creation of the Association using the LACP Protocol and ports still work as four individual switchports.

  The neighboring switch talking LACP? If he is put in LACP active mode? At least one device must be in LACP active state, and both must talk to LACP. Maybe you could try to replace orders 1 channel-group passive mode 1 mode channel-group active in your configuration.

  Best regards

  Peter

• Cisco 2960 and uplinks AIR-AP1041N

  Guys,

  what I'm doing wrong here?  I need to enable trunking to pass on several VLANs to my AP, but when I put the 2960 as trunk mode I lose connectivity to the AP.

  All will help it useful!

  Course AP Interface congfigs:

  interface GigabitEthernet0.210
  210 native encapsulation dot1Q
  no ip route cache
  Bridge-Group 1
  No source of bridge-Group 1-learning
  Bridge-Group 1 covering-disabled people
  end

  +++++++++++++++++++++++++++

  210 native encapsulation dot1Q
  no ip route cache
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  end

  2960 new switch port config (lost connectivity to AP unless I put back to access the mode vlan210 why?)

  GigabitEthernet1/0/1 interface
  AP USTCRLW001 description
  switchport mode trunk
  SRR-queue bandwidth share 1 30 35 5
  priority queue
  MLS qos trust cos
  Auto qos trust
  end

  Add this on swicthport where AP is connected:

  GigabitEthernet1/0/1 interface
  AP USTCRLW001 description

  Switchport tunk native valn 210
  switchport mode trunk
  SRR-queue bandwidth share 1 30 35 5
  priority queue
  MLS qos trust cos
  Auto qos trust
  end

  Concerning

  Remember messages useful rates

• Inter vlan routing on a Cisco SF 300-24 port switch only no internet except when scanning with wireshark

  Hello

  I'm get inter vlan routing to work on a 300-24 ports switch DF.    I have a network of business existing on 192.168.111.0 and want to create a vlan on 192.168.1.1 which can talk to 192.168.111.0.    I activated the layer 3 routing on the switch through the console and also provided ip routing commands. I have the following VIRTUAL networks:

  Vlan1 - default 192.168.111.0

  VLAN2 - 192.168.1.0

  I turned on DNS and provided my two servers DNS 192.168.111.82 & 192.168.111.212.

  I updated the VLAN1 interface 192.168.111.217 and VLAN2 interface 192.168.1.1.

  The FE1 - FE15 ports are access ports and assigned to VLAN1 (unidentified)

  FE16 - FE24 ports are access ports and assigned to VLAN2 (unidentified)

  I put a default route for the switch to 0.0.0.0 0.0.0.0 192.168.111.254 (router Draytek 2600). I have connected a computer (A) at the port of VLAN1 FE3 and a computer (B) to VLAN2 FE16 port.   I put its IP address and computer default gateway has to 192.168.111.217 to 192.168.111.94.    I updated computer B default gateway 192.168.1.1 and 192.168.1.2 IP.

  Computer A has access to the Mdaemon Server files via the network grows but no internet (cannot ping google) and can ping computer B and RDP on computer B.

  Computer B can ping computer A and RDP on A computer but do not have access to the company network i.e. MDaemon, file server etc.   It can also access the internet.

  The console I can ping www.google.co.uk and all the ip addresses in the network of the company i.e. 192.168.111.82 (DNS server).   I do not understand what I am doing wrong and have been banging my head for staretd a few days a new job and desperately need to work so any help would be greatly appreciated

  If I have computer scanner a wireshark wirh internet starts working wheird!

  Show the configuration below:

  switch7c0a71 #show run

  database of VLAN

  VLAN 2

  output

  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___

  Add a voice vlan Yes-table 00036 b Cisco_phone___

  Add a voice vlan Yes-table 00096e Avaya___

  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___

  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone

  Add a voice vlan Yes-table 00d01e Pingtel_phone___

  VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075

  Add a voice vlan Yes-table 00e0bb 3Com_phone___

  interface vlan 2

  IP 192.168.1.1 255.255.255.0

  output

  interface vlan 1

  IP 192.168.111.217 255.255.255.0

  output

  IP route 0.0.0.0 0.0.0.0 192.168.111.254

  interface vlan 1

  no ip address dhcp

  output

  Hello interface range vlan 1

  hostname switch7c0a71

  No complexity of passwords allow

  No server snmp Server

  interface fastethernet1

  switchport mode access

  output

  interface fastethernet2

  switchport mode access

  output

  interface fastethernet3

  switchport mode access

  output

  interface fastethernet4

  switchport mode access

  output

  interface fastethernet5

  switchport mode access

  output

  fastethernet6 interface

  switchport mode access

  output

  interface fastethernet7

  switchport mode access

  output

  interface fastethernet8

  switchport mode access

  output

  interface fastethernet9

  switchport mode access

  output

  interface fastethernet10

  switchport mode access

  output

  interface fastethernet11

  switchport mode access

  output

  interface fastethernet12

  switchport mode access

  output

  interface fastethernet13

  switchport mode access

  output

  interface fastethernet14

  switchport mode access

  output

  interface fastethernet15

  switchport mode access

  output

  interface fastethernet16

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet17

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet18

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet19

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet20

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet21

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet22

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet23

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet24

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface vlan 2

  name of development

  output

  Hi Richard,

  43 - permit Protocol: any / all

  42 - Protocol deny EVERYTHING 192.168.2.0 0.0.0.255-> to 192.168.111.0 0.0.0.255

  41 - Protocol to deny ALL 192.168.111.0 0.0.0.255-> to 192.168.2.0 0.0.0.255

  40 allow the RDP Protocol TO ALL

  etc.

  To block everything, including MSSQL, with the exception of the RDP and other ports that you defined above.  The other defined are simply not the RDP Protocol and service work?

  Richard, do note useful messages and identify the right answers.

  Best,

  David

• Join CISCO AP 1041N to a series of 2500 WLC

  Hello

  I have a problem to join CISCO 10 AP 1041N to a series of 2500 WLC.

  I have the following network architecture,

  A Windows Server 2012 R2 (DC, DHCP and DNS server) connected to the CISCO 2960-X Series (this switch is connected to 2 other switches, same model), 10 of the AP and the WLC are connected to the same switch, as I have 3 NIC on the server I use one for Internet between the firewall and the other three are teamed together and connected to the switch.

  I tried the following methods:

  -J' used the 43 Option on the DHCP server: does not work

  -J' added 2 DNS entries (cisco-capwap - controller.mydomain and cisco-lwapp - controller.mydomain): does not

  -UDP Ports CAPWAP and LPWAP are enabled on the Windows Firewall: does not

  My WLC is set mode controller Master, I see all of the AP in the DHCP server with IP addresses assigned by the server and the WLC as well, and they can ping each other.

  Furthermore, the WLC, I have one (management) interface with VLAN ID 0, the server has (VLAN by default) no assigned ID, the switch have VLAN ID 1 (default) and I tried to change all the on the same VLAN ID 1 (server, Switch, WLC) in this case the server is not able to communicate with each other and DHCP does not work.

  Thank you for your help.

  Oh, your APs are standalone, that is why they can't join the WLC. Convert into light! Here's a good guide - http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/