question of maintenance mode

Similar Questions

• Questions about maintenance mode

  I have some curious (probably dumb) questions on the service mode (esxi worm 51).

  • What is exactly?
  • What happens if you run the patch similar to ' esxcli software vib /vmfs/volumes/datastore/patch_zipfile.zip d install "without putting it in maintenance mode?
  • What happens if you put maintainece mode, install the patch, and then out of maintenance mode before restart? The reason behind this is so that the virtual machines will autostart.

  These are just curious of rhetorical questions.

  Thank you!

  Arch

  All the maintenance mode has really is sure no VMs are running. In an environment of DRS, VM will migrate automatically away, basically saying maintenance mode "do not put a machine virtual here, is about to have some work." Without the DRS maintenance mode will fail and advise you to move the virtual machines yourself.

  Some patches require no maintenance mode and install fine. Those who demand the it will error and refused to apply without maintenance mode.

  In the third scenario, the machines will be autostart

• Question on maintenance mode

  I was going to put a host in maintenance mode and then stop it.  It has a few models and virtual computers, but nothing works.  When I choose to spend in maintenance mode, it offers the possibility to "evacuate power off" VMs.  Do I need to do?  These virtual machines are not necessary today, once I have finished, I want to feed them back to the top.  I want to leave them on the host, if I can, but I don't want to lose them.

  you do not have to evacuate the powere doff Vms - they will be there when you go back to the host.

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• Question about the Maintenance Mode

  Hello
  
  Is there a way to customize the maintenance mode message that opens in the workspace when user tries to access the planning application is maintenance mode?
  
  Currently, this is the message that is displayed:
  
  An error occurred while processing this page. See the log for more details. If please close the current tab and open the application again. Application is in maintenance mode. New connections are not allowed.
  
  Please let me know if there is a way to personalize this message.
  
  
  Thank you
  ~ Krrish
  
  Published by: Krrish on January 21, 2013 11:59

  I only did this, but it seems easy enough. Have a look here: http://docs.oracle.com/cd/E17236_01/epm.1112/hp_admin_11122/ch13s05s01.html

  You will update the HspCustomMsgs_en file.

  Hope this helps,
  -Jake

• Question on the Maintenance Mode

  When you select "Shutdown" or "Reboot" in the vClient, I get the following message:

  "The host is not in maintenance mode. Are you sure that you want to, stop, or restart >? »

  I looked in the manual and it does not need the ESXi host in maintenance mode before you shut down or restart.

  I would like to confirm that there is no harm to execute an action when NOT in maintenance mode.

  Thank you

  This is more than a warning.  If you have guests running on your host computer, they will both go down.  But if you have no guests, no harm.

• DELL Dimension XPS T800r CMOS Maintenance Mode worries...

  Greetings, good people of the world of DELL!

  I'm working on a desktop DELL Dimension XPS T800r for a neighbor.

  The original complaint: no video

  Some things have changed since yesterday when I worked on it, then read on...

  Here's what I've done so far in order:

  (855) 935-7526 *. Exchanged video from a well-known donor cards.  No change.

  2. the DIAGNOSTIC LEDS on the back panel has found.

  3 DIAGNOSTIC LIGHTS remain DARK during the start attempt.

  4. consultation documentation DELL for LIGHT codes DIAGNOSTIC.

  5. the code is: All the DARK - turns on by default.

  6. again consulted the DELL documentation to identify what to do:

  (a) reinstall microprocessor

  (b) remove all the expansion cards

  7. After you do both.  No change.

  8 using the prior computer knowledge, I pulled ALL of the motherboard except the feeding fittings and connections on the front panel.  I unplugged all connectors power hard drive as well.  I left only the CPU fan connected to the motherboard.  I checked the power supply against DELL standards and all is good.

  9. now, knowing the CMOS batteries, I checked the voltage on board.  He was 3.1VDC.  Seems good.  I didn't want to remove it, so in order to make sure it's properly plugged in, I turned the battery making to create a better connection.  That's where things have changed since yesterday...

  10 leave the BARE Board, I plugged it in to the power supply.  Silence.  Only the yellow led on the motherboard lit up.

  11. I installed the CPU and VIOLA!, LIGHTS flash YELLOW for a second DIAGNOSIS, and both fans turn quickly upward, then will stop altogether.  The yellow led on the motherboard remains on.

  12 DELL documentation contains this code to represent: card system is powered,
  but the BIOS is not executed.

  13. I think turn battery CMOS created a better connection (the computer IS almost 16 years old) giving me a response to market now.

  14. I tried to reinstall everything and document what happens after turning the power on.  Nothing changes beyond this point.  LIGHTS DIAGNOSTIC flash YELLOW briefly, and the power supply and fan rotation CPU for a second, then stop.

  15 DELL documentation suggests putting the system in MAINTENANCE MODE by the CMOS jumper

  This computer is almost 16 years old, and very probably, the owner has not saved the BIOS settings.

  This is what is installed, before the Panel:

  A CD-ROM drive

  An IOMEGA Zip drive

  A floppy drive

  Now to the question:

  Since I have no way to backup or recover the CMOS settings, I hesitate to put the jumper to MAINTENANCE MODE to see if the computer will boot all the way to the top.  I'm not potentially make the computer unusable in maintenance or replacing the battery mode, even though I would replace the battery because of the line due to age.

  The DELL documentation:

  NOTICE: Pass by the maintenance mode returns all settings in the
  Installer system to their default values. Dell highly recommends
  that you save or print the current settings before entering in this
  mode, so you can fix them when the system is reset to normal
  mode.

  What do you think will happen if I reset the default BIOS by moving the jumper and replacing the battery?

  I will cause a catastrophic failure?

  Now, the other side of the coin is that the system is relatively basic, so I have to enter the starting sequences and other isn't a big deal.  I hope...

  At worst, I'll have to use a drive caddy to retrieve its data from the hard drive.

  Thanks in advance for all your help and support!

  Austin Cajiao

  In case it helps someone, re-seats maps microprocessor and expansion got the computer fully functional again.  I guess that for a computer in 16 years, the tabs or oxidize some and created resistance which forbade the computer recognition and power.  It works fine now.

  -Austin Cajiao

• Can you change what core is vmotion ports without going into maintenance mode?

  If you have a host running, with a vswitch standard, can you change what port kernel manages vMotion without putting it in maintenance mode?

  What is happening is that we have a number of blades, all running vSphere 5.1.  Each host has a unique vSwitch with multiple groups of ports and a dedicated port vmkernal for vmotion and another dedicated one for the management network.  We use a VLan to separate the vmotion network.

  Our networking group will do a reconfiguration that will change the VLan dedicated for the vmotion.  What I would like to check the vmotion network management for each host, clear the check box on the Group of ports "vmotion".  The new vmotion VLAN is set up by the network, and then I go back and make the changes on each slide so that the "vmotion" is now enabled and remove the functions of vmotion for the management port.

  I know that it is not recommended to run the vmotion traffic on the management port network, but it will only be short term (probably a week or two).  My biggest concern is whether I can make changes 'live' without affecting the machines running.

  In a note related, if a host loses contact with other hosts on the network vmotion, which will pose a problem (in addition to not being able to vmotion)?  Will be the loss of connectivity on only the port of vmotion cause any kind of response of isolation, failover, etc.. ?

  Basically, you can modify most of the settings of network - including vMotion - without affecting the virtual machine. When you say that they reconfigure VLANS, do you know how long it will take and if the VLAN current will be available during this time? In this case, you would not have to implement no work around, but just update the VLAN groups of vMotion ESXi host ports.

  André

  PS: about your question "will be the loss of connectivity on only the port of vmotion cause any kind of response of isolation, failover, etc..?

  No, it's the management network that is used for HA, so everything what he let go is vMotion/DRS.

• Maintenance Mode settings

  Hello

  quick question - if Update Manager attempts to a host address and there is a virtual machine on the host connected to a physical scsi device on the host (eg. a tape drive) the host will not be able to enter in service mode using vmotion to move the virtual machine to another host. If there are other virtual machines on this host which can be moved to other hosts using vmotion, they automatically migrates the vm remaining with the physical scsi connection be suspeneded (if this option is chosen as the failure of maintenance mode response)?

  Thank you

  Steve

  the only way that a task remidiation will inaugurate an automated DRS event is if you have a fully automated value DRS.  If this is the case, all the guests who can vMotion.  The other must be powered off or suspended.

• Ways to put the application in read-only during the monthly maintenance mode

  Hello
  
  We have a situation where, during the maintenance phase every month for 2 or 3 days, I need to put the application in read mode only. We already have the dimension security level applied to each user, but even to users who have write access to certain members on the forms of data etc., the app just can't be read only during this period so that no user can enter data.
  
  I know the application in maintenance mode, all users will be be locked is not what we want. Users should always be able to see the dataforms, reports, etc. So, please let me know your ideas on this.
  
  Any ideas are appreciated.
  ~ Hervé

  The same question was asked the other day - How can I request a read-only?

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• Redirect users to the page when you take the system into maintenance mode.

  I want to redirect users to the page when you take the system into maintenance mode. We are on 12.1.3 application. Please provide me with the document who have these details

  Please see old threads that deal with the same subject.

  http://forums.Oracle.com/forums/search.jspa?threadID=&q=redirect+and+maintenance&objid=C3&DateRange=all&userid=&NumResults=15&rankBy=10001
  http://forums.Oracle.com/forums/search.jspa?threadID=&q=maintenance+and+message&objid=C3&DateRange=all&userid=&NumResults=15&rankBy=10001
  http://forums.Oracle.com/forums/search.jspa?threadID=&q=outage+and+maintenance&objid=C3&DateRange=all&userid=&NumResults=15&rankBy=10001

  Do a search of the forum before posting similar questions.

  Thank you
  Hussein

• 11i maintenance Mode

  I have some confusion on maintenance mode while using adpatch: -.
  Adpatch assistance to put the application in maintenance mode before the fix is applied: -.
  Oracle recommends: -.
  (1) termination of the application.
  (2) activate the Maintenance Mode.
  (3) patch.
  (4) turn off the Maintenance Mode.
  (5) start application.
  
  I am aware that maintenance mode means conceptual * "feature from the maintenance mode stop Workflow Business event system and implements the security function so that no Oracle Applications functions are available to the user."
  
  My question is if we bring any application then anyway workflow will be down, application is not available, so no safety issue (for as much as the feared front end), why oracle has developed the concept of bringing the instance in maintenance mode. Response may be to set the correction process, but can someone tell me how it was achieved? What is its internal functioning, how maintenance mode attaches the patching process? If any note or any document so please let me know.
  
  Thank you

  Hi user;

  We had a similar discussion please check below thread

  adpatch - maintenance mode

  Check the related note, advice etc.

  Respect of
  HELIOS

• adpatch - maintenance mode

  Hello
  
  What King of the patches are to be applied in maintenance mode?
  
  What happen internally when you activate maintenance mode?
  
  Is there a difference between the activation of the mode of maintenance and stop intermediary services?
  
  Pls send your suggeastions.
  
  
  Thank you for always
  JP

  Salvation;

  What King of the patches are to be applied in maintenance mode?
  What happen internally when you activate maintenance mode?
  Is there a difference between the activation of the mode of maintenance and stop intermediary services?

  Mainly, you need to take maintenance mode for can apply the patch to your system. But there are several option for can apply the patch as option /hotpatch. Wiht /hotpatch option you can apply the patch while your system is running.

  For all your question you need to understand the concept, thatswhy please read first under notes, if you have any question yet unanswered in your head that post here please.

  R12 in the mode of Maintenance of Applications and prevent the access of the user [557964.1 ID]
  Maintenance - a new feature in 11.5.10 mode [ID 291901.1]
  How to apply the patch without activating the Mode Maintenance [375130.1 ID]
  http://www.Scribd.com/doc/20615209/maintenance-mode-in-Oracle-applications-EBS

  See also below thread which we have discussed on the docs to patch information:
  Adpatch utuliy
  Re: Patch and worker issues

  PAtch patch-hot
  /Hotpatch

  Respect of
  HELIOS

• The ESX host is in maintenance mode

  SE Vfoglight triggers always rules if an ESX host is in Maintenance mode? If so is it good for the maintenance mode that I can use to stop firing rules.

  There is such a property, inMaintenanceMode

• SX20 running in maintenance mode

  Hello everyone,

  I have a problem with my camera of telepresence SX20 (TC6).

  It runs in mode of maintenance for 2 days.

  No one has changed nothing.

  Do you know how to fix it please?

  Have you tried to do a reboot? This could be the silver bullet that works in 90% of cases.

  The maintenance mode starts if the system crashed for some reason any and without

  interaction, that he would stay like that.

  If you restart the system, and it starts again at the maintenance mode, please try to do a reset to factory default.

  Please remember useful frequency responses and identify useful or correct answers.

• C20 in maintenance mode. The key audit has no output

  Ladies and gentlemen,

  There is a unit of Cisco TelePresence system Quick Set C20 is currently stuck in a maintenance mode. This is a most important error message to the event log (complete log is attached):

  May 12 11:21:18 (none) principal: Releasekey check failed.

  I downloaded the keys option and liberation for the Cisco Licensing Portal system. How can I install on the codec of the console?

  Any help will be really appreciated!

  Thank you.

  Hello

  Thanks for sharing the newspapers!

  The console shows one of the customers hand log does not. Customer 169.254.0.12 is not responding. It's the ARM2 processor.

  [C20: ~] $ arp - a

  ARM1. LocalNet (169.254.0.11) to 00:e0:0 c: 00:8 c: 41 [ether] on eth1

  ARM2. LocalNet (169.254.0.12) to 00:e0:0 c: 00:8 c: 42 [ether] on eth1

  arm0. LocalNet (169.254.0.10) to 00:e0:0 c: 00:8 c: 40 [ether] on eth1

  HSRP-144-254-13 - 1.cisco.com (144.254.13.1) at 00:00: 0C: 9f:f0:01 [ether] on eth0

  [C20: ~] $

  I'm afraid that there is a material error, therefore, you need to open a Service request to get the replaced C20.

  In the newspapers, you also arm0 - System.log and arm1 - sytem.log, but arm2 - system.log is missing.

  Kind regards

  Danny.

  The console log

  =========

  From main

  Hand began, waiting for ready system...

  Admin time is set to 60 seconds

  Timeout - 3/4 customers have reported

  (missing communication with customers of 1/4)

  We have 3 guests

  Customer ppc.localnet (169.254.0.1:60354)

  State: emitEnumInfo

  Debug info: {0: {'hw_id': 0, 'prg_id': 0, "req_id": 0}, 1: {'hw_id': 0, 'prg_id': 2, 'req_id': 1}}

  Customer arm0.localnet (169.254.0.10:45396)

  State: emitEnumInfo

  Debug info: {0: {'hw_id': 0, 'prg_id': 4, "req_id": 0}, 1: {'hw_id': 0, 'prg_id': 1, "req_id": 1}, 2: {'hw_id': 0, 'prg_id': 3, "req_id": 2}}

  Customer arm1.localnet (169.254.0.11:47286)

  State: emitEnumInfo

  Debug info: {0: {'hw_id': 1, 'prg_id': 4, "req_id": 0}, 1: {'hw_id': 1, 'prg_id': 1, 'req_id': 1}}

  Monitor listening on port: 60354

  Main crashed with exit code 1

  tshelld: listen to 127.0.0.1:4217

  Has expired while waiting for system ready signal

  ERROR: S80main: failed