R6400 router Internet intermittent issues

Similar Questions

• ESXI network/Internet connectivity issue 4 with a guest

  I worked on it now for a few hours and I can't understand what is happening. I'm under ESXI 4.0 on an x 3230 with a processor intel 1000 inside. There are currently 4 guests installed operating systems. 3 are centos 5.3 (64-bit) and the new (the one that does not work) is windows xp (32 bit).

  I got a 29 awarded to the host, so I can give each machine a virtual address static primary ip then subnets secondary route to the primary ip address. The IP addresses I am award are entirely routed internet IP, lan not local addresses, if that makes a difference.

  3.4.5.192 = network

  3.4.5.193 = entry gate

  3.4.5.194 = vm1

  3.4.5.195 = vm2

  3.4.5.196 = vm3

  3.4.5.197 = installation of xp broken comments

  3.4.5.199 = distribution

  I have install publicly routed internet blocks before and never had a problem. I checked the host logs, nothing found. ipconfig/all seems ok, good dns/gateway/subnet/etc. The driver for the VM (AMD PCNET) network card is installed, it seems to work fine. It is connected to the switch from the virtual machine just like my other virtual machines.

  I am at a loss of what I'd do next shoot evil. Are there problems with 32-bit windows running on the same host as linux 64-bit? Does anyone have ideas, what may be the issue? I searched on google for similar situations, but found nothing useful.

  Someone invited linux 64bits along a guest of windows 32 bit successfully?

  Say that you wanted to enter

  192.168.252.197

  but in fact you entered

  192.186.252.197

  Made easy

  Please give points for any helpful answer.

• Satellite C660-258 - Internet connection issues

  Recently, my laptop started to suffer serious problems when you try to connect to the internet.
  My download and upload slow to a crawl (only for laptop)

  Usually (according to speedtest.net) I get around a download about 4 but on my laptop it reaches maximum 0.09 dl.

  Whenever I restart my laptop it works kind of during about 10 minutes (I get about a 1 download), but then it slows down to a crawl.

  I confess that I am not the most tech savvy people so I only did the basics (turn it on and try again, other connections, reset the router, connect through a cable) but none of this has worked.

  Any help you could provide would be most welcome.

  Oh btw, my laptop is a
  Satellite C660-258

  Hello

  To be honest I don t understand your problem you have a problem with the internet connection is slow?

  Usually, this is not a problem or computer in the system but the problem with the connection provided by the internet provider (ISP).

  However, you compared the speed using LAN and WLan?
  Did you check the internet connection by using other WLan hotspots or other WiFi network?

  Do this!

• Re: 1670 - back to 98SE - Satellite Internet connection issues

  I used W2K on my 1670 for quite awhile, but it was slowish, so I decided to put in the recovery disks and return 98SE.

  As the laptop is quite old and has no ethernet as the material, I also installed a PC Ethernet Card Bus line and this has been properly installed in Device Manager.

  Have upgraded to IE6, been through the Internet Connection Wizard, settings of the LAN, server proxy automatic etc... However, the IP address is always zero. I can't fix the ethernet connection and there are options to adjust the dial upwards, but as I do not use that may be unnecessary.

  Is there a problem here? I have not had any problems with my Portege 4000 which had ethernet installed as part of his equipment.

  > Is there a problem here?
  You're joking now? ;) What is a question after 9 years.

  You use laptop at home connected to the DSL router?
  A firewall is turned on?
  You can assign the IP address manually?

• HP Pavilion G4 1125 dx Internet connection issues

  As the title HP Pavilion g4 1125 dx, Windows 7 (Home Premium) 64-bit processor, 2.6 GHZ AMD says.

  Here's the story. Had at best buy with geek squad black tie. Cracked screen. returned, returned, screen works fine.

  Installed firefox, avast free antivirus, Sims 3.

  Then I turn it on one day and it cannot connect to the internet. Usually no problem. Run the diagnosis, can not solve the problem.

  Tried everything fix but still does not.

  At work when I got it, when I came back he connected, but I noticed it worked intermittently, and now it has stopped working all together. Is there a simple solution or do I restore settings?

  Hello

  From what you describe, it looks like a hardware problem with the wireless card.

  Is your laptop still under warranty?

  If this is the case, you can contact HP and arrange for the repaired laptop.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  Kind regards

  DP - K

  

• Wireless router + internet = blu - ray player?

  Is it possible?
  I use the Belkin router 54 + existing as a bridge/access point wireless and get a new N Router for the internet.
  It is possible to configure the wireless ap/bridge G router and connect it with a cable ethernet for the BDV-E370?

  I am answering my own question.
  It is possible.
  I loaded the dd - wrt firmware on both routers and I configured the router that is connected to the Sony Reader as a client bridge or Repeater (acts as an Extender of signal with half of the speed + wap).
  YouTube is a very good video on dd - wrt Repeater bridge Setup.
  http://www.YouTube.com/watch?v=UD-Hq3kgvk4
  I had a router Belkin F5D7231-4, but I've upgraded to a router n, Linksys E2000, which is the Repeater on 5 GHz bridge (main router is a Linksys WRT610n-v2). Both work very well.
  I bought the rebuilt a little more than for ($65+$ 32) then the Sony usb adapter, but at the same time, I upgraded my network 2.4 ghz + 5 ghz n too. So basically I have two simultaneous networs in my house.
  If you use only a router that you add to your existing wireless network, it is much cheaper then buying the Sony adapter and at the same time that you can extend your wireless signal too.

• Internet connection issues "Limited or no connectivity." and "windows could not find a certificate to log on the network.

  I'm so unable to connect to the internet?

  Hello.

  I'm so unable to connect to the internet.

  Since I've renamed our WiFi network and add a WEP key, I have problems with wireless connection on my
  Windows XP computer desktop, which is a Dell Dimension 4700.

  The questions that I get connection are...

  "windows could not find a certificate to log on the network.

  "Limited or no connectivity."

  I did all the solutions I could try to fix the connection problem!

  1. once I received the message "limited or no connectivity", I click with the right button on the connection and click on repair. It is not always connect for me and I got the "limited or no connectivity message.»

  2. then, I disabled the network connection and then enabled. That no longer works.

  3. I tried to withdraw from the ordered list of connections, and it still doesn't work.

  4. I checked the driver manager, and initially the Ethernet driver was outdated and missing of its pilot. He had a yellow question mark with a black sign and yellow with an exclamation mark inside.

  5. I used DriverZone, downloaded the driver, installed and rebooted the computer after the installation of the it. Apparently, it worked. But I could not always connect.

  6 I have ensured that I entered the correct WEP key, and then adjust the settings correctly. I did it like 10 times in a row and would not always connect.

  7. I tried to go to the command prompt and typed in IP Config/All and that's what I mean.

  Windows IP configuration
  Node type: unknown
  Active IP routing: no
  WINS proxy enabled: no
  ETHERNET connection to the Local network card
  State of the media: Media disconnected
  Description: Intel PRO/100 VE Network Connection
  Ethernet card 2 wireless network connection:
  Suffix the connection-specific DNS: (EMPTY)

  8. after that, I typed the command: ipconfig/release
  and then I got this error...

  No operations can be performed on the connection to the local network, although it has its media disconnected.

  9. after that, I tried Googling for some solutions, and the solutions I found were not any use.
  A solution was

  10. opening of Services...
  Start | Run | Type: services.msc | Click OK |
  Scroll down to and double-click Client DNS | Set to automatic on startup
  type |
  Click apply | Click the Start button | When it starts, click OK
  Do the same for the DHCP Client.
  Do the same for the remote procedure call (RPC).

  and it still doesn't work.

  11. when I look in the menu network connections, I see my connection with a lock on the side, with a red X under the lock and key. In the description, I see not connected, protected by a firewall. How could I remove the internet connection firewall? I disabled the firewall and that did not work.

  12. I tried to uninstall and reinstall the network card and who does not work either.

  It is not the network itself that is the problem.  It is not the modem or the cable. There are no disconnected son or something like that. We have other computers in the House and the internet works fine on other computers. As I said, since I renamed our WiFi network and added a WEP password, I had problems with connecting to my Windows XP computer.

  My computer has updates that must be installed as well. Updates would fix the problem? I just need to have internet.

  What should I do? Thank you for your time.

  Sincerely,

  Justin

  Have you tried to set the value of the link speed/duplex mode? I had the same problem you describe. Your card is only capable of 10/100 communication.

• The G7 Pavilion Internet connectivity issues

  Help! I'm working on a laptop for a consumer, and I'm stuck hard. The laptop is a G7 Pavilion with Windows 7 64 bit. The machine was given to me under the principle of "The Internet does not work". Properties with wireless and LAN settings say that the laptop is connected and it has Internet access. I can ping outside the machine address and can ping the machine from other devices. It is also a valid ip address according to an ipconfig. However, when you try to pull on a Web site, there is a page "Web site is not found." This happens on IE, Firefox and Chrome. All drivers ethernet drivers, chipset and wireless drivers were uninstalled and reinstalled. They are the latest drivers available on HP website. I even replaced the wireless NIC thinking it's maybe just a bad card. I checked the IPv4 settings and all is good. Think to any DNS problems, I tried using directly the IP to connect to Web pages, but all without success. I'm quite baffled and need advice. Is there BIOS problems that adversely affect this? Any suggestion would be appreciated.

  Hey Darken_Rahl,

  Hmmmmmmm... interesting.

  Are you able to ping to an IP address?

  I don't think that you are dealing with a hardware problem, it must be the establishment / OS related.

  This really looks like a DNS issue even if IP navigation does not work. You have emptied the DNS? If this isn't the case, please do so now:

  1. Press Windows Key + R.
  2. Type cmd , and then click OK.
  3. Type ipconfig/flushdns and press on enter.
  4. Test.

  Also try these in an elevated command prompt:

  1. Start.
  2. Type cmd in the search.
  3. Right click on cmd/prompt commands and run as administrator.
  4. Type netsh I I r r and press ENTER.
  5. Type netsh winsock reset , and press ENTER.
  6. Restart.
  7. Test.

  Let me know the results of those.

• WRT54G drops internet intermittently.

  My Linksys router WRT54G has recently (yesterday) begins to the internet after having been online for a few hours.

  The current configuration is in place for several years.  I started with the broadband provider and they checked the signal and cable modem works properly.  My own tests back this up.

  At first, I just reset the router.  It disconnected for 30 seconds and is plugged in.  Internet is back.  Then I tried to reset the router and the modem cable.  It also works well but the problem presists.  Reset the router itself has the same effect.

  So something with the router is the cause of dropping the internet.  The network does not go down however.  I can still use my network drive and the computers indicate a network without internet connection.  This is true for the PC wired as well as those who use a wireless connection.

  Check if the router is on the latest firmware, if not to update.  Once upgraded to hard reset the router by holding the button of reset in the back for 30 seconds then release. Wait 10 seconds and cycle power to the router.  Reconnect via wired computer and go to 192.168.1.1 and reconfigure the router from scratch.  Try now.

• Linksys WRT 1900ac internet connectivity issues

  I apologize in advance for a potentially easy question, but I'm not very familiar with how to solve these problems, but I digress. I recently bought a new router to replace and older router that was functional, but the beach leaves to be desired. The old router, which was a cisco worked fine, but when I plugged my 1900ac upwards the light internet blinking white, and I have no idea how to fix this. I don't have any internet access. I am currently using my old router. any other important information that my ISP is Atlantic broadband and the supplied modem was a motorola SB5120 surfboard cable modem. I would really appeciate a soultion wise step to my problem.

  Thank you in advance!

  Try the cable modem and the router, and then plug off the modem. Wait for the modem to get all it's lights on. Then reconnect the router. Some modems/ISP lock the MAC address in the cable modem, so it will not 'allow' traffic unless they match.

• With Microsoft Vista and McAfee Internet connection issues

  Hi I would appreciate any help with this issue.  I'm not a very experienced user.  I'm having all kinds of problems with McAfee Security 9.0.  He stops working and says I have no internet connection and that you can not update. I contacted McAfee and they came on my computer, uninstalled and reinstalled and I'm still having the same problem.  Them, that I came across an article from McAfee dealing with this problem and Windows Vista.  I have the 64 bit version.  The solution is 1. Click on the Windows button and type cmd.

  2. right click on cmd and run as administrator

  3. at the prompt, type the following command, and then press ENTER:

  netsh int tcp set global autotunninglevel = off

  It then gives you instructions to reactivate the auto-tuning network if this does not resolve the problem.

  I would like to know if anyone has tried this and the results, also if this works this deactivation causes me to have other problems with my computer.

  This may seem very simple for some people, but because I'm not known I want to create more problems than I have now.  Through this site, I learned how to remove McAfee from my computer, and it would be the last thing I would do if nothing works.

  Thank you... Victoria

  Hello

  It's as good as anything else, it's free and designed to work properly with Windows OS'.

  http://www.Microsoft.com/security/PC-security/MSE.aspx

• HP Envy M6 loses internet intermittently when running on the battery.

  Hello

  Recently, my HP Envy M6 has been intermittently lose internet during the execution of battery - it's always nice when it's plugged in, however. I ran the diagnostics manual wifi and nothing is not detected.  Any ideas?

  I am running windows 8.1and model number model is: E0R92EA #ABU

  Thank you

  Brian

  Brian,

  This could be a setting in your profile (or power saving wireless mode) power setting?

  I had problems where an update (from HP, not Windows) changed (my) default settings for power profiles.

  Can you restore back a few days or a date prior to the problem? This would test if the a software update changed something...

  Kind regards

  Louis

• Internet - connection drops with my Toshibha laptop/internet connectivity issues arrives and stops randomly

  Original title: Internet connectivity

  my computer toshiba laptop windows 7 just started to fall sharply internet all in a show that is to connect to the internet all my other devices all always online - internet comes back randomly and goes off randomly - tried all settings to make sure that everything looks good.

  Hello

  Welcome to the Microsoft community.

  I understand that you have a problem with internet connectivity. We apologize for the inconvenience caused to you. We also indicate the steps you did.

  I would like to know the details below to help you better.

  1. What is the model number of the laptop you are using?
  2. Do you have a code error message when connecting to internet?
  3. You did changes to the computer before the show?
  4. You are connected to an internet connection wired or wireless?

  I ask you to run the Network Troubleshooter utility first to see if it can help diagnose and solve your problem. Open the utility of network troubleshooter by right-clicking the network icon in the notification area, and then click troubleshoot.

  You can also run the troubleshooter of Internet connections by:

  1. By clicking on the Start button, and then clicking Control Panel.
  2. In the search box, type Troubleshooting, and then click Troubleshooting.
  3. Under network and Internet, click connect to the Internet.

  If the problem persists, try to perform the steps of troubleshooting mentioned below in Microsoft Help article and check if that helps.

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows/cant-connect-Internet#1TC=Windows-7

  Keep us updated on the issue to help you better.

• Route Internet traffic against the default VPN on SAA route

  I want to transfer all internet traffic to a VPN connection via the internal network and not divided the digging of tunnels or direct connection to the internet from the OUTSIDE interface.

  I have a VPN connection default gateway, so all traffic is pushed back on the OUTSIDE interface when the VPN is in place and the user connects to the Internet.

  Is it possible to send Internet traffic to the INSIDE interface, internal network, to route to the Internet.

  I'm not looking for another solution, it's the design, I would like to implement.

  

  As always, any help is greatly appreciated.

  Of course you can, simply set the following text:

  Route inside 0.0.0.0 0.0.0.0 in tunnel

  The foregoing will force all VPN traffic after be decrypted to the next break of the SAA within the interface defined above

• RV082 - routing with quickvpn issues

  Hi all

  I ve a special configuration to my network, we have about 20 sites managed by an external supplier. Last week, we bought a Linksys RV082, in order to enable remote access in our network.

  It is possible to configure the router with an ip address public luckily. We are currentliy use tar on the firewall to allow access to the router. / * Style definitions * / table. MsoNormalTable {mso-style-name : « Normale Tabelle » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-margin : 0 cm ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  IP nat inside source 192.168.5.180 static and external IP address

  When I opened the public ip address in my browser I can access the web interface of the router. So far so good.

  The WAN Interface is configured as follows

  Static IP 192.168.5.182

  Subnet 255.255.255.0

  Gateway 192.168.5.254

  DNS 192.168.1.1

  The unit is configured as a router (with the two RIP) and a 192.168.252.1 IP address. (This network is unique in our company)

  The firewall is disabled

  HardwareVersion 2

  When one add a pptp user and enable the pptp, I m able to access each subnet in our company server

  When I add a user QuickVPN and successfully establish a connection, I m unable to access any subnet/Ip in our company. Only the WAN IP 192.168.5.182 is ping-able. I can't ping any device, neither the 192.168.252.1 nor the 192.168.5.10

  This is the routing table when you're connected via pptp

  List of Routing Table entries

  Destination IP address	Subnet Mask	Default gateway	Hop Count	Interface
  192.168.252.1	255.255.255.255	*	50	ppp200
  192.168.252.200	255.255.255.255	*	0	ppp200
  192.168.5.0	255.255.255.0	192.168.5.182	0	ixp1
  192.168.5.0	255.255.255.0	*	40	ixp1
  192.168.5.0	255.255.255.0	*	45	ipsec0
  192.168.252.0	255.255.255.0	192.168.252.1	0	ixp0
  192.168.252.0	255.255.255.0	*	50	ixp0
  by default	0.0.0.0	192.168.5.254	40	ixp1

  My questions,

  How to configure the device to access the network via quickvpn as pptp?

  My goal is accessible?

  I ve no more ideas, the I ve found anything in the internet, or on google, nor in this forum that match my troubles.

  Please give me your comments, regards dario

  PS: Sorry for my bad English...

  It will be difficult, especially because QVPN does not allow you to configure it to several networks. The reason why PPTP and QVPN work doesn't have is the Protocol in use. QVPN use IPSec in which you specify the authorized networks, where in PPTP you log only the user to connect to the device or the server. There are ways to deceive our router so that we can make what you need, but it is not easy and you are limited to the number of users who can use the connection. I wrote a couple of 'how to' using IPsecuritas for Mac and also shrew VPN. You will not be able to get several subnets with the QVPN customer.