WRT54G drops internet intermittently.

Similar Questions

• Signal strong wifi X220t Centrino Advanced-N, intermittently, dropping internet

  My problem is different from those who have difficulties to internet connection in tablet mode.

  Maintain a continuous and strong/full wifi signal, I lose internet access intermittently.  It makes no difference if the unit is used in laptop mode or tablet. If I reset the wireless adapter, I stay connected to the internet for anywhere from a few minutes up to an hour or two.  The wireless signal is always at full power, and the distance between the router makes no difference.  Sometimes the Internet returns and plunges again, however, I usually run the Troubleshoot utility to reset the connection.  Diagnostic/troubleshooting of windows running resets the adapter and returns the message: "the connection between your access point, router and Internet is broken" and "the default gateway is not available", but only temporarily solve the problem.  We have two other laptops in the household who are unaware of connection difficulties.

  So far I reinstalled the drivers from the Lenovo site and have set power options for maximum performance for the wireless adapter.  This is a brand new unit used for a few days and has had the problem since I have it unboxed.

  Resolved - seems to have been a problem with my router, which unfortunately is a model of Netgear wireless-N - ish.  Switched on to another router and it seems to work fine now.

• The misfortunes of WRT610N - signal high but dropping internet

  So I got a WRT610N since June 2011 - works perfectly without having to think about, I just hooked it up and it has been on the default settings and never gave us any problems.

  About a week ago the power went out - and it caused the router to reset to the factory settings. I've put up with our network name and the security and don't think much. After that, we started to notice questions on our phones and laptop in the kitchen.

  I work in the same room as the router, wifi and did not have the signal drop once since then--my work laptop is about 3-4 feet from the router. Another PC through the router works fine

  Continuously on the strip of the 5 GHz for tv, a room, works perfectly, like netflix, youtube, etc on the TV.

  Once you get to the kitchen, on the laptop there (which has been there for months without problem), wifi is completely laminated. This is maybe the router through only 1 wall of 40 feet. The signal of 3 to 4 bars and windows reports still says 'internet access' for the State of the connection, but the connection drops on a regular basis, and you must manually disconnect and reconnect to the wifi to restore internet access. It of the same story with the phones if you are more that about 20 feet from the router - they have a strong signal, but will be lowered on a regular basis, requiring you to disconnect and reconnect. The 2.4 GHz and 5 GHz bands seem to be behaving in the same way.

  Normally, I would say that the power outage fried the right thing and get a new one - but he is works perfectly at short range and still give a strong signal to longer-range - juggling just not the internet.

  I factory reset it several times since it began. I tried different settings on both bands, different security, no security, etc. But nothing seems to help, that's why I post here - help!

  Thank you for reading.

  Try to reset to the factory settings and then update the firmware. After the update of the firmware, a 30-30-30 reset hard and then reconfigure the linksys from scratch.

  InSSIDer allows to find the best channel. And try to use 20 MHz only for the width of the channel.

  If by chance your modem is a router too (for example. "You have DSL), try to change the local IP address of the linksys 192.168.2.1.

• Weird WRT54G, DDNS, internet connectivity problem

  The other day, we lost power at home (my cable modem and the router are not on a UPS system - they will be soon). The problems started shortly after that (it cannot be a coincidence, but I'm puzzled by the way in which they are involved). After having everything turned on, we could no longer connect to the internet from any machine on the network. When I checked the WRT54G, however, I found that it was connected to the outside world and that she had a valid IP address from my ISP. Poking around outside my network (at work, for example) showed me that if I try to connect to my web server, I on the contrary am routed to router setup page (I have config remote power off and on port forwarding, and it worked without problem in the past).
  Further investigation showed that my DDNS (TZO.com) service did not work (the error message is 'Connect to server fail'). I checked with TZO and they don't see a problem on their side.

  Any ideas for further investigation? I'm stumped at this point. I would almost say that the problem of fried power the router, but if it did, it seems to be a terribly selective frying. Thanks in advance and please let me know if more information is needed to help.

  My configuration:
  Modem-cable Time Warner Roadrunner (not sure of the type/model)
  Router Linksys WRT54G, firmware 4.21.1
  TZO.com DDNS service

  Well try upgrading the firmware on the router & keep holding firmly the reset button with power light flashing on the router & then make a complete network power cycle that is, unplug the power to the modem & router cables & then plug the power to the modem cable first once all the lights are solid green you could plug in the power cable to the router & check-out it will certainly work!

• HP Envy M6 loses internet intermittently when running on the battery.

  Hello

  Recently, my HP Envy M6 has been intermittently lose internet during the execution of battery - it's always nice when it's plugged in, however. I ran the diagnostics manual wifi and nothing is not detected.  Any ideas?

  I am running windows 8.1and model number model is: E0R92EA #ABU

  Thank you

  Brian

  Brian,

  This could be a setting in your profile (or power saving wireless mode) power setting?

  I had problems where an update (from HP, not Windows) changed (my) default settings for power profiles.

  Can you restore back a few days or a date prior to the problem? This would test if the a software update changed something...

  Kind regards

  Louis

• HP6600 drops internet connection, can't print wireless

  My 6600 seems to drop our wifi signal every few minutes.  I can not connect to the printer from any device without wire (iMac, HP desktop or laptop).  I tried the unplug reset twice and entered manually our wifi information.  Any advice on how to improve our connection?

  Thank you dzanotti. Assuming you have a "HP Officejet 6600 e-all-in-one printer - H711a/H711g' is a specific document to: printer does not maintain the wireless connection.
  
  Follow the path of troubleshooting for your operating system and let me know if that helps.

• EX7300 drops internet connectivity

  Hello

  so I bought myself an EX7300. Manual configuration went all well.

  My problem is, that, although Windows indicates that it has access to the internet and the wireless signal is at the highest level, my internet connection is lost every few minutes. I have to toggle the WIFI connection to regain access to the internet, but once again, it's just for a short period.

  When you perform a repair of Windows, the message is: Windows cannot communicate with the device or resource (primary DNS server) [main DNS server is 192.168.0.1]

  The Extender has a static IP address which is 192.168.0.50, but gives the router a DHCP IP which is 192.168.0.106.

  Firmware is the newest: 1.0.0.44

  It's really annoying and restores the Extender completely useless.

  Any suggestions?

  Thank you

  NX

  I think I solved the problem by giving the router a channel fixed wLAN (48) and the Repeater another (40). Have not had this problem since.

• R6400 router Internet intermittent issues

  Hi all

  Got Netgear R6400 and for help from behind the ISP supplied Modem/Router, even though I turned off the Wifi of the provided ISP router functionality. When you are connected normally awhile, I'm not able to access INternet Wifi was shown to be connected.

  Also not able to ping to the IP address of the ISP router provided at the show, once she came back after reboot while other times it solve just after a few minutes. Router watch new Firmware is available, but I don't know if he can really solve the problem or aggravate the situation. While I connected the NAS (QNAP) with her and she is very stable and better speed thn my old DSL68U from ASUS.

  The ISP modem /router must be placed in bridge mode OR change the r6400 for AP Mode

  Page 128

  http://www.downloads.NETGEAR.com/files/GDC/R6400/R6400_UM_07Aug2015.PDF

• R8000 Open VPN drops Internet connection

  I have a router R8000 and sometimes when I go to connect by using the open VPN connection that it will show as connected but I don't have any internet access more. My connection log is below. The XXX is corresponding to my external IP address of the router.

  I have the service defined on the port UDP 12970 type. Firmware version: V1.0.3.4_1.1.2

  Journal will be in the next post, because there is a limit of 20,000 characters.

  In fact, I found a way around the problem. If you change the Protocol to TCP UDP everything works fine. Don't know what the problem is with UDP though.

• D7000 continually drops Internet connection

  My new D7000 abandons the Internet connection up to 15 times a day... Sometimes it will run for hours without problem and other times, falling from every 10-15 minutes

  He is recovering normally, but he sometimes needs to be restarted manually. As far as I can see, the WAN/Internet is configured correctly for my ISP (BT) because it works perfectly fine, until he falls
  (I'm not network guru, but know quite well what I do!)

  I have tried eaves values MTU of switching given that others had found that fixed things for them and just changed PPPoA to PPPoE encapsulation without success.

  I do not use the latest firmware (given that the update of my old router Netgera bricks it!), but downloaded it read to install manually the next step.

  any help please?

  V1.0.0.18_1.0.1 firmware version
  ISP: BT

  Basically, I discovered the following of my ISP:
  The initial problem was the result of a failure of the infrastructure - they replaced a wiring for my property
  The subsequent recurrence of symptoms has coincided with the upgrade of their Exchange works - they do not alert me of the upgrade until it was completed.

  Since then, the connection remained constant and reliable while being 4 times faster than originally.

  So, I think that the question is entirely the fault of my ISP.

• LOSE INTERNET INTERMITTENTLY DUE TO COMPUTER PROBLEM

  After a full close and sometimes in-use my internet is de-energized and when I 'view available wireless networks' in the Advanced section, the check box for "USE WINDOWS TO CONFIGURE YOUR WIRELESS NETWORKS" has allowed himself, can I lock it or set a default sort?

  XP Home Edition on a LG X 110

  Thanks in advance

  KOBODAVE

  Hi David_Campbell5,

  1. you receive an error message or error code?

  2. what service pack is installed on the computer?

  3 did you changes to the computer before the show?

  Method 1: Follow the steps in the following link and check if that helps.

  Windows wireless and wired network connection problems

   

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

   

  Method 2: Update the NIC drivers and check if that helps. Check out the following link to update the drivers.

   

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

  You can also see the following article for more information about wireless network problems:

   

  To set up automatic wireless network configuration

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/wlan_client_configure.mspx?mfr=true

  Let us know if that helps.

• Gets the error - failed to connect to the internet intermittently in the Windows XP machine.

  Original title: intermittent connection problem.

  I have intermittent connection problem - every few minutes says that it is impossible to connect, when I click on diagnose and then then the connection is re-established. This happens on a single PC - I have 3 on the network.

  Maybe it's my imagination, but when I disable the 1394 adapter, it seems to be more reliable

  I reinstalled the network driver, BIOS and chipset drivers (they were all out of date anyway)

  My problem, which could be caused by Norton firewall? Is it likely to be hardware related software?

  Hi Mattsurf,

  If the problem is not repeated in safe mode, there is probably a startup item or service is causing the problem. Follow the steps on the following link to locate the item or service responsible for the error:

  http://support.Microsoft.com/kb/929135

  Cody C
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• WRT160N guard dropping Internet when you transfer large files or using the Zune software

  WRT160N wired for 3 PC (only regularly on 1 - Vista), Wired XBox 360 on or off - does not seem to effect things) (normally closed) Wii wireless, wireless laptop Vista

  Everything works fine, except when I download either a file (for example when my Zune software is downloading podcasts each day), or when I transfer or access files on the network (copy or modification of the files of the laptop on the desk)-any attempt to do something on the internet is to expire. I don't lose my connection, just cannot get anywhere.

  Any help is appreciated.

  Recently, I made the following revisions, but have not seen a significant improvement:

  Wireless settings should be band Radio frequency should be 20 MHZ OF the self

  First check if the same thing happens the modem If yes contact you ISP.

  Please disable all firewall, antivirus and alarms on your computer and if the problem affecting the area.

  If then still reduce the MTU size to 1200 and update the firmware on the router, follow the steps to update the firmware of the router.

  Go to the Web site template linksysbycisco.com/downloads...insert in your serach tab... select the correct version of your router router... Download the firmware file... save this file on the desktop...

  Follow these steps to upgrade the firmware of the device: -.
  Open a page in Internet Explorer browser on a computer hard wired to the router...
  In the address bar type - 192.168.1.1... Leave name empty username & password admin lowercase usage...
  Click the 'Administration' tab - then click on the 'Upgrade Firmware' under the tab-here, click on 'Browse' and navigate the .bin firmware file and click on "Upgrade"...
  Wait a few seconds until it shows that "the update is successful," after the upgrade of the firmware, click on "Reboot" and you will be returned to the same page OR it will say 'cannot display the Page.

  Now reset your router:
  Press and hold the button of reset for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router... This should solve your problem.

• WRT54GS - no internet connection is detected and yet my computer cable to connect to internet through router

  I had my router for a little over a year. I am connected to a wild blue satellite modem. He has worked without problem for a year.  Now, he claims not to detect an internet connection, even if the computer connected to the router has no problem connecting to the internet. I just can't connect wireless to the internet because the router thinks that there is no internet connection. I have reset several times, turned on and off the power to the modem, followed all the troubleshooting instructions. All the lights on the modem and the router. I need to replace the router, or I would encounter the same problems with a new?

  If you use the update 1.6 LELA LELA 3.0 and your problem will be solved.

• Aspire connected bluetooth V3-731, signal drop internet wifi

  What can I do to improve this

  The BT and Wifi use the same antenna. Try the suggestions here:

  http://www.Goldtouch.com/stop-Bluetooth-interference-messing-devices/