Re: NB200 - 10 p Overclock

Similar Questions

• HP Envy 860se Phoenix: Overclocking HP

  I recently bought a Phoenix envy with a k 5820 in it, and I'm looking to do some overclocking. I want to mention comes with HP cooling by closed circuit water, which I don't know. I was wondering how long should I overclock the 5820 k (I heard it was a beast) with the cooling of the HP (is it still good?) and how overclock on the HP motherboard. Thanks for your help!

  PhoeNiX777, welcome to the forum.

  You can go into the BIOS to find the section for Overclocking.  As for how far can the processor be what OC'd? -It depends on the processor.  I've never found two processors that OC the same.  The best policy is to take in small increments.  This ensures that it is not too overheat.  HEAT is your enemy.  Liquid cooling can make a big difference, but it still has its limits.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• NB200-13th change in Windows XP to W7, W8

  Someone who comments if it is advisable to spend the W XP, because the support ends and Windows must be?

  I checked the Toshiba download page and your NB200 is supported for 32-bit Win7, so I recommend you to install Win7 32 bit.
  All the tools of drivers and utilities that you can find on http://www.toshiba.eu/innovation/download_drivers_bios.jsp

• NB200 - how to integrate the audio drivers for Windows XP Home edition?

  Can you give me an idea for my Toshiba NB200 guy.

  I use nlite and don't create addons for my realtek (audiodriver) but it no chance that the installation is not successful.

  Toshiba has a software to create an audio driver windows xp built-in?

  Thanks in advance...

  Toshiba does not provide any software to integrate the drivers, but Toshiba provided software to create the own recovery disk (or recovery media)
  The creator called pre-installed software Toshiba Recovery Media (disk beginning) created the recovery disc to install the image of Toshiba.

  But this software was available on laptops with preinstalled system. He of not ready for download.

  However, I used nLite repeatedly in the past and never had serious problems to add additional drivers to my Win XP system.
  I have created my new installation disc and added all Win XP Service Packs.

• Satellite P300D 12L - I want overclock the processor

  There are nearly two and a half years since I am the owner of this laptop.
  I want to overclock the processor, AMD Turion X 2 Ultra ZM 80, but I have found no information, guides or tutorials on this topic.
  Could someone help me?

  Thank you

  Hello

  I would not recommend this!
  First I put t think you would be able to overclock the CPU from the laptop's BIOS does not support this option.
  Secondly, the cooling modules could not be able to cool the CPU and it would lead to overheating and damage s notebook.

  S of CPU for desktop PC can be overclocked as the cooling system desktop PC can be upgraded and you can use a system or other fans of cooling water
  This allows to keep the temperature down, but it is not possible for laptops!

• NB200-10Z does not start - slect boot device message

  Hello, sorry for my English, I'm Italian and I have him translated by the translator.
  I am writing because I have a big problem.

  My toshiba NB200-10Z has this break: I turn it on and I get the "Toshiba innovation leader" screen and bottom left shows «crazy (F2) Setup, press (F12) to the boot device selection menu...»

  No matter what button I press him, and still nothing happens. I tried to replace diskbench hard ram, but nothing does not change.
  I don't know what to do.

  I am very worried. Can you help me?

  Thank you to tell me everything

  Dino, Rimini Italy

  Usually, the message appears because the laptop could not boot boot device...
  In most cases the disk HARD is not found in BIOS due to the fault and therefore the laptop not found system.

  Question: are you able to access the BIOS F2 key?
  If so, the HARD drive is listed in the BIOS?

  You can boot from another bootable media such as disk or a USB key?

• NB200 - 11 H - igxprd32 error BSOD

  Hello

  has the following appears on my netbook from Toshiba NB200 - 11 H 13 months about a week before,

  A problem has been detected and windows has shut down to prevent damage to your computer
  The problem seems to be caused by the following file: igxprd32
  If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps.
  The device driver got stuck in an infinite loop. This usually indicates problem with the device itself or
  With the device driver, hardware programming properly.

  Please check with your hardware device vendor updates the driver.

  Technical information:
  STOP: OxOOOOOOEA (Ox83B77DA8, Ox84B7512O, OxOOOOOOO1)

  Igxpr32
  Beginning physical memory dump
  Total physical memory dump.
  For more assistance, contact your system administrator or technical support group.

  I live across the computer shop where I bought a year ago, so I took on the whole, they made a check of PC and can't find anything wrong with it, the only way they could get the operating system working again was to disable the drivers for the graphics card, but also had to disable windows update to prevent it from updating the drivers.

  Once the update was installed, the blue screen of death appeared again. Then I took at home so that it operated worked OK less pilots and removed the small amount of info on a memory stick, as they have advised me to do a reinstall of the software. After what same error screen appeared.
  Then I connected an external hard drive made a recovery disk made the full restore, thought he had worked as the Welcome screen Toshiba confirmed few details clicked the name of the computer, etc. on finish began to load windows.

  Then the same message high again its ugly head. I took it in my friends in the computer store, they have tried the same thing as me with the same result. Anyone have any ideas on how I could resolve the situation.

  Hmm. Entendez_ you the new recover system solve your problem and the BSOD appeared again?
  Well, sounds like a hardware problem
  I think in the first step, modules memory must be checked, that it is the first part of the hardware that may be causing the BSOD.

• Battery suddenly stopped working the NB200-10z

  Once I plugged it in the charger while my phone was off.
  He lit LED Plug and battery LED was flashing after 3 seconds.

  I reinserted the battery and it loads fine.
  One day I was using my NB200 and he runs the accusation, I plugged and same thing happen but even after reinserting the battery it does not start.

  Plug in it for a long time doesn't warm battery or cell phone. I can only start it without a battery connected. Insertion of battery stops PC after 1 seconds and battery light flashes again after 3 seconds.

  What does that mean? I tired battery put in the fridge because I read on the internet that he could solve, but no luck.

  No idea how I can solve this problem.

  Hello

  First of all, must know that the laptop should run fine without the battery with AC adapter plugged.
  Even if the battery is defective or empty, the plugged AC adapter should feed and you should be able to turn on the laptop.

  In case this isn't possible, I guess electronic power supply failure.

  However, you might try the following workaround solution:
  Try to propel upward and for the laptop without the starter battery.
  Then go to Device Manager and uninstall the following entries under batteries:
  -Battery composite Microsoft
  -Battery method to check compatible ACPI Microsoft

  Reboot the laptop.
  Turn off again and insert the battery.
  Power on the notebook and check if the device should work correctly.

  Of course, it also would you recommend to test the laptop in the framework of another good and tested the battery.

• NB200-12N - USB port does not work

  Hello

  I updgrade my OS from windows 7 starter edition to now a windows 7 home basic 32-bit usb port does not work is the (only) in the left near card reader sd and lan.
  Can you please hellp me to install it? I have download the drivers from Toshiba for my NB200
  But does not work.

  Thank you

  Paulo

  If everything is OK and right drivers all USB ports should work. You cannot install the drivers for each port separately and force one of them to work properly. On this machine, all three ports are the same USB2.0 ports.

  Try reinstalling the chipset utility.

  By the way: two other ports work well, right?

• Failed to start on NB200

  Hi guys,.

  I have a tablet of Tosh NB200 - it does not start!
  The HARD drive seems failure and dropout at startup - if I hit F2/F12 it says "Please wait...". "and nothing
  If I type F8 - nothing - hold 0 to start - nothing

  Any ideas? I have partmagic/magicboot but nada. IV ' e an external CD drive connected but nada! As im pissing against the wind here!

  By pressing the F2 key at the beginning should allow you to access the BIOS.
  If this isn't possible, you have a serious hardware problem (probably the motherboard).
  Dysfunction of memory can affect the laptop as well as other parts of motherboards tiny start-up.

  You can check if one of the RAM modules is achieved, if the modules are ok, he should have another question and it of really difficult to say what could be the problem exactly.
  This should be checked by a technician for laptop.

• Failed to start NB200

  Hello

  My NB200 freezing on bios photo from the beginning.

  There are several discussions about on various forums about people having this issue and nb200 nb205, apparently for the most part bought around August 2009. Some people have suggested 1 - to put the notbook in the freezer for 30 minutes then 2-windows and it of possible 3-implementation to date of the bios.

  But when I use the toshiba bios update:
  http://www.Toshiba.fr/innovation/JSP/supportMyProduct.do?service=FR

  I get this error:

  "the incorrect rom size.

  This update of the BIOS is version of WIN and must be started with Windows.
  Can you start Windows or not?

• How to turn of the NB200 - 10 G with the lid closed?

  I almost always use my notebook NB200 - 10G with external monitor/mouse. And since the powerbutton is really accessible with the cover closed, it should be possible to start the computer without having to open the lid, turn it on and then close the cover. Does anyone know how to do this?

  If you clear the netbook, I'm afraid there is no way to turn it on without pushing the Start button. (opening of the cover).

  A far-fetched possibility is to install some sort of bouncy ball out on the Start button, close the cover and then use an air pump manual external to swell for a short while when you need to start the netbook.

  But I just imagined such a solution, never tried.

  However, it is sometimes possible to put the device in hibernation. In this case, if you si vous choisissez choose 'allow the network wake-up upwards' (this is not literal, I don't remember the exact words) in the menu CMOS, turning on an ADSL connected to the LAN port (or something similar), should wake up the equipment.

  This can not be used if you unplug the power running all in hibernation, because allowing more upward by characteristic network leaves some active electronic parts and this drain on the battery in a few hours.

  I am interested that possibility, in my view, it can be a little experience. I intend to put the netbook in a more or less hidden corner, I use also screen, mouse and external keyboard. If you do some experiments, please message results here so other people can use it.

• NB200 Touchpad + 2 buttons failed

  Model name: NB200-136
  Part number: PLL23E-00900QH2

  I tried to reinstall the drivers and BIOS flashing. Also formatted my net book, passed on Windows 7 to 8.
  Don't show no mouse or the touchpad in the Manager device. Maybe use the wrong set of drivers?

  I posted this problem in the Toshiba USA forum as well:
  http://forums.Toshiba.com/T5/keyboards-touchpads/NB200-touchpad-2-buttons-failure/TD-p/342532

  Any suggestions?

  > No mouse or the touchpad are showing in Manager devices. Maybe use the wrong set of drivers?

  The touchpad device should be visible in Device Manager; as a device marked with a yellow .this exclamation or unknown should be visible even if the driver would not be installed.

  But if the device (touchpad) is recognized by the system, then either is disabled (in BIOS) or it malfunctions.
  Check the BIOS settings.
  Here you can enable / disable the touchpad (pointing device)

• NB200-10Z - how to restore factory settings?

  Hello

  I seem to have a pretty annoying problem with the NB200 - 10Z.
  The operating system is WinXP SP3.

  I was looking to restore it to its factory settings by using the tools of Toshiba, pressing F8 during the boot sequence, this however does not take me to a screen where I can choose 'Repair' as online guide of Toshiba said.
  My only options were by selecting start normally, or start in safe mode, safe mode with network and so on. I have consulted the original manual included with the laptop, but that doesn't make the light on the problem, in fact I found the manual to be pretty empty.
  There isn't any help on formats, restore to factory or other maintenance. Disappointing.

  Another option is creating a recovery disk, however, Toshiba tool will only advise that it cannot find all the stations that contain writable media, simply because the NB200-10Z is not a CD/DVD/BD drive. The only available ports are SD and USB.

  So my question is, how do I format/reset to factory settings the NB200-10Z without external CD/DVD/readers writers, using the USB/SD slots? Because I can't find a way to create an ISO recovery with the Toshiba tool, which I was able to get on a bootable USB device.
  And even if there is a way to do it, how do I adjust the NB200 to boot from USB? Looking at the bios settings and boot options, showed that only the LAN and HARD drive are supported.

  Greetings,

  Boris

  Hi Boris,.

  Usually, if you start media recovery disk creator, you can choose on which device (CD/DVD or USB) the recovery media must be created. There you should be able to change between the CD/DVD drive and USB. If you select USB you can create the recovery on a USB media.
  You can boot from that disk if you connect before you start the computer, then go to the start of the BIOS (F12) menu and then you can select the USB key.

  According to the manual of the drive recovery HARD can be started while pressing the value 0 (zero) key before Windows starts.

  Check this box!

• Impossible to activate wireless lan on NB200 using the Fn + F8 combination

  Hello

  I just created Linux Ubuntu 9.04 on the Toshiba NB200. Unfortunately, it seems that without active wire.
  Try the Fn + F8 key combination does not help to turn on the wireless LED. Someone at - it an idea how I could
  activate the wireless thing in a different way on this laptop.

  Thank you very much
  P

  In Windows, you must install a driver to use some Fn keys. It must be enabled by default under Linux, then maybe the Wifi driver has not been installed?