Re: Value added package does not install correctly

Similar Questions

• Satellite A200-1N8: value added package does not

  Hello

  I have Toshiba A200 1N8 and which tent to install value added package to my computer laptop everything seems ok, but nothing chnaged in the configuartion of windows, the keyboard shortcut and function keys do not work.
  I think that changes have not taken effect.
  I tried uninstalling and reinstalling, safe mode... nothing has worked

  How can I solve this problem?
  My laptop is a model 6 buttons

  You must first remove the old version of VAP.
  Then you must download the new VAP for the A200 series right.
  As you know different A200 series exists and you must choose one that fits.

  In addition, you can choose the version of Toshiba controls for 6 control button.

  Best regards

• Vista + value added Package does not work on the Satellite A100-002

  Hello

  I have a laptop Toshiba Satellite A100-002, and I am running windows vista.
  I tried to install all the drivers, but I can't do it with value-added Packege. (VAP)

  I got this error message:
  [http://kepfeltolto.hu/i/?173242&t=img]

  I need that the programs included in the VAP.

  Pls help me!

  Thank you...
  David

  Hey Buddy

  Today, it's lucky day you ;)
  Why?

  I have a solution for you.
  The ID_ERR_NOTINSTALLTVALZ error message due to an old version of the BIOS.

  It should Flash the newest BIOS with compatible BIOS which can be downloaded from the Toshiba driver page.

  See also this thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=20471&MessageID=75256

  It describes the same problem and it confirms that a BIOS update should help.

  Concerning

• Satellite P300 - Value Added package does not work after the computer restarts

  Hello

  I have a Toshiba Satellite P300 PSPCCA Windows vista ultimate x 64. I can't do my work button soft touch. I downloaded latetest VAT package and installed. After installation it asks to restart but I restart my laptop and I make just restart Flash Card and my button works all good touch app that is silent, Media Player, etc., but once I restart my laptop it stops working.

  I tried the uninstaller and reinstalling but no luck. I read in the forum toshiba on running CCleaner and do a fresh install but still have the same problem.

  Does anyone of you knows how to solve this problem.

  BTW, I got the software AVG internet security on my system, but have added folder toshiba for exclude of realtime scanning just in case if its causing problems but not luck. I searched qurantine folder and its nothing in there.

  Please help me get my work button soft touch.

  Thank you.
  Kind regards
  Jay

  Post edited by: Jay Padia

  Hello Jay

  I agree with Akuma. All you can do is remove VAP preinstalled system and reinstall the latest version. Why you didn t follow the instructions to restart the computer after the installation of VAP?

  I installed VAP several times on my Satellite P200 and Satellite A300 without any problem, but after installing the latest version, I rebooted phone immediately. The procedure of the facilities has been completed and necessary processes started in the background. I guess that's the problem on your Satellite P300.

  If nothing is done the last step is to install the OS by using the DVD facilities. After doing this you will own preinstalled OS and everything works well again.

• Dependence of the Lenovo 1.2.0.21 settings package does not install correctly

  Lenovo system update offered an update package dependencies of parameters. After installation and reboot, I got a pop up telling me that 'C:\Program' is not found.

  What's happened is that Setup you forgot the quotes in a registry entry:

  PWMTRV had a value of

  Obviously a few citations are missing, so that the background monitor of power cannot be loaded. I would just add the quotation marks, or it will soon be an update?

  
  

• Re: New value-added Package does not work on Satellite A300D

  Hi all

  Hoping you can help me keep my good deal Toshiba Satellite A300D I ve purchased.

  I can't turn off my mouse touchpad like the disenable isn t available option. My function/hot keys also don't work.
  Called Toshiba who advised I have download the VAP via tinyurl.com what I did. Its now sitting on my desk.

  What should I do to get her active as always impossible to disable touchpad? Reboots do not solve the problem. Do I have to find a type of 'run' action to fix, and if so, how?

  Thank you very much

  Hello!

  Normally, you can disable or enable the touchpad in the Synaptics driver.
  Go to the control panel-mouse-device-online settings setting online online
  In addition, enable/disable the touchpad, you need the utility of the touchpad. You can download this package on the Toshiba site.

  Also make an update of the Hot Key utilities.

  Good bye

• 2013 redistributable Visual Studio does not install correctly

  After you install our program on a computer laptop users and attempt to run the application, we see this error message:

  "The procedure entry point? Bios_base@STD@@QBE_NXZ is not found in the MSVCP120.dll dynamic link library. "

  For the record:

  1. Our Installer includes the Redistributable 2013 package.
  2. The redistributable package has been executed and reported success
  3. The redistributable was for the good (vcredist_x86.exe) target for the Win32 application.
  4. A run the stand-alone redistributable package it reported success, but the same error message is displayed when you attempt to run the application.

  The corrective action that actually worked was:

  • delete MSVCP120.dll delinquency
  • run the uninstall of the redistributable
  • Re - install the redistributable

  The application worked.

  Now for the questions.

  1. What happened to install it? I seems to work but does not work.
  2. What should I change to ensure that it works for all customers?

  Hello

  Thanks for posting your query in Microsoft Community.

  The question could arise if the redistributable is not installed correctly or corrupted package installed. If you get the number again, you can follow the steps provided below:

  Method 1:

  a. click Start, right-click computerand then click Properties.

  b. in the name computer, domain, and workgroup settings , click change settings.

  (If you are prompted for an administrator password or for confirmation, type your password, or click continue.)

  c. click change settings , and then select the Advanced tab click the environment variables button.

  d. the user variables area, click on TEMPand then click change.

  e. in the Variable value box, type C:\Temp, and then click OK twice.

  f. click applyand then click OK.

  g. follow steps 4 to 6 for the variable of environment TMP as well.

  h. confirm this folder C:\Temp exist, otherwise create a.

  i. restart the computer.

  j. attempt to install the application again.

  If the steps do not help, try the next method.

  Method 2:

  If you are comfortable in changing some registry settings, then follow the steps provided below.

  1. Click Start and type run in start search box, and then press enter.
  2. Type regedit and click OK.
     Registry warning:
     Important: This section, method, or task contains steps that tell you how to change the
     Registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 KB
     How to back up and restore the registry in Windows
  3. Go to HKEY_CLASSES_ROOT\Installer\Products\F942F94A19C0F79468FD2B85E5E8677B
  4. Right-click on this registry entry, and then click Rename.
  5. Rename F942F94A19C0F79468FD2B85E5E8677B to -F942F94A19C0F79468FD2B85E5E8677B.
  6. Close the registry editor.
  7. Restart the computer.
  8. Check if you are able to install the application.

  If the method does not resolve the problem, continue to the next method.

  Method 3:

  You can also reinstall Visual C++ Library Runtime components to solve the problem.

  You can uninstall all existing Microsoft Visual C++ Redistributable Package and install the Microsoft Visual C++ Redistributable Package 2013 and check if it helps.

  Step 1: To uninstall the package:

  1. Open programs and features, click Start > Control Panel >programs and features.
  2. In the list, find the Package redistributable Microsoft Visual C++ and click on it.
  3. Right-click on it and select Uninstall.
  4. Restart the computer.

  Step 2: Download and install the package and see if it helps.

  Click on the link below and install it in your computer.

  Package redistributable Visual C++ to Visual Studio 2013

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• 6110 driver update does not install correctly

  I had XP drivers for 6110 all-in-one printer installed and running - 09/03/2003 - V 2.4.1.8.

  I went to the page "HP Officejet 6110 all-in-one printer drivers", HP Officejet basic driver, under "Driver - software product (3) installation" saw that - 2009-09-12, Version 4.2.1 (34.23 M) was the last version recommended, so I downloaded to a folder on my C: drive.

  I ran / run the file downloaded in this folder, but the wizzard installation only got during most of the first two of the four elements-ball before he stopped. Apparently, it uninstalled my original driver as the new hardware detected msg appears and calling "Print" of an application has not found the 6110 options of the printer. So I rebooted the system and run the installation file downloaded driver in the same folder again. This time, it appeared to get through most of the four bullets-Articles of the wizzard, and when I tried to print from an application, he finds the 6110 printer, but with a completely different interface. However, when I went to Control Panel / administrative tools/Device Manager and checked the current version of the driver for the 6110, it showed 14/10/2002---2.0.0.134, an older version of what I had previously.

  Since there is no instruction 'on-screen', I got aware of the printer and the USB connected all the time.

  What happens and how can I get the latest version of the driver to install properly? My motive in update was for further selection options to correct paper for the newest Premium HP Photo papers which I couldn't on my original driver version, or (obviously), I see on the old version 2.0.0.134.

  Thank you, Waterboy71,

  As I did not have an immediate response, I've resorted to trial and error and came up with the same solution you suggest - i. e., downloading and installing the long SW and pilot w/cables etc seconded. He was soft - installing the cables being detached probably being the cure for my original problem in the installation...

  Which leaves me with the same driver I had initially - i. e., 09/03/2003-V 2.4.1.8 (and what seems to be a large number of additional baggage - files in C:\temp, which I don't remember in my original version of work) that is better than going backwards.

  I'll just keep trying by trial and error to get the best quality using ink HP and HP Premium Plus Photo Paper photo prints, as advice from HP for this product of revised on printers before 2009 document is to use a selection that does not appear with the V 2.4.1.8. driver/sw - i. e., select 'Advanced Mode '. But I am familiar with all the things HP has said about this document updated the and I will work.

  I will say that the download page for 6110 drivers need to edit to avoid confusion even for others. It offers three choices for the updated drivers - i. e., 1) HP Officejet basic driver (34MO), 2) HP multi-function products driver Bundle - Corporate only (69 MB) and 3) HP Officejet and PSC full feature software and driver (166 MB). However, after getting the first to install, I found that it installed the old driver and all documents supporting documents and references for the company, small footprint, version - not what is implied in the description and date/version of the first and reasonably inferred from the comment on the second object the corporate package. It seems that the incorrect file name is attached to the first choice, but I did not load the second to see what happen (but maybe I'll do that on a lazy day). Someone should check all three and make descriptions in line with pilots produced on download...

  Anyway, thanks again and I'll mark the issue as resolved.

  John

• Microsoft Visual C++ Redistributable Packages do not install correctly.

  I recently built a low buget of range, PC game for my sister, so she can play games like the Sims 4.

  After you install a copy of Windows and the drivers, I have installed some games and programs she wanted.

  Most of the program works correctly, but the Sims 4 does not work. It gives the error of "msvcr100.dll is not found, re-installing the application may fix this problem". I think that means that Visual C++ Redistributable is not installed, but all the Microsoft Visual C++ Redistributable packages 2005-2015 (32 and 64 bit) are installed.

  I tried to reinstall the packages, they did successfully,

  I tried to reinstall the game,

  I tried to run the packages again, and they said they were already installed on the system,

  I tried to use Windows update,

  but none of these methods worked.

  Specifications of the PC are:
  Intel Core 2 Duo E8500

  4 GB RAM DDR3

  GeForce GT 240 (1 GB GDDR5)

  Windows 7 Pro (64 bit)

  HARD DRIVE 320 GB

  Hello

  Thanks for posting your query on the Microsoft Community.

  According to the description of the problem you are facing problem with Microsoft Visual C++ Redistributable Packages that failed to install properly. Try the steps below and see if it helps.

  Method 1

  You can try the steps from the following link and check if it works, you can ignore the steps that you have already tried.

   

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows7/troubleshoot-problems-with-installing-updates

  Method 2

  If the problem persists I suggest to reset the Windows Update components and for this, try to run the fixit described in the following article.

   

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058/en-us#LetMeFixItMyselfAlways

   

  Method 3

  If after completing the two steps issue persists try to perform the clean boot and temporarily disable security software , then check to install the updates.

   

  Step 1: Perform the clean boot

  Put your system to the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

   

  How to perform a clean boot in Windows

  http://support.Microsoft.com/kb/929135/en-us

  Note: See "How to reset the computer to start normally after a boot minimum troubleshooting" to reset the computer to start as usual after a repair.

   

  Step 2: Disable Antivirus

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attack.

   

  Step 3: Download the update

  Download the updates manually from the link provided below.

  MFC Package security update Microsoft Visual C++ 2008 Service Pack 1

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=26368

  MFC Package security update Microsoft Visual C++ 2005 Service Pack 1

  http://www.Microsoft.com/download/en/details.aspx?ID=26347

   

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Kind regards

• Silverlight does not install correctly and be unistal not at all what should I?

  Silverlight has never installed correctly and when I bilel uninstall under programs it shows and white sheet of paper as an icon and no memory used, when I try to uninstall to do a fresh install, because udates won't take it says it cannot uninstall due to the fact that it is not able to match or find the file adiquit.  I can not it turned off my computer so I can put it right and now I can't watch netflix.  Please help :)

  Hi Nicole,.

  Please see the center of support of Silverlight here: http://support.microsoft.com/ph/12929#tab0 where there are different ways to get help (self-help, assisted support, community & forums, resources, or contact technical support (but the latter is probably costs money unless you meet certain specific criteria)), if you can't find what you need to get their resources , and then search the forum and if you still don't have an answer, post a question in the forums where experts on this program will provide assistance best we can because that's their specialty.  While we try to cover some Silverlight questions here in the answers (even if it's the wrong forum even for that), we do not have the dedicated experts that they do in their own forums.

  As alternative, if this does not help, and I'm not 100% sure since while I used it successfully for hundreds of other programs and the only ones where I had problems and kidnapping special tools were also some deep-seated AV Suites, I never really tried with Silverlight, but you can try Revo: http://www.revouninstaller.com/revo_uninstaller_free_download.html in Advanced Mode and see if that helps.  It often does the trick when the normal uninstall process fails for some reason any.  And because it does a better job, that's how I always uninstall anything I install to keep my cleaner system and do a better job preventing the remnants of disenfranchised (and my experience says that virtually every uninstalled program leaves in the normal way of things behind this Revo intercepts and removes).

  I hope this helps.

  Good luck!

• 7520 photosmart all-in-in-one: software does not install correctly

  I have installed and uninstalled 3 or 4 times. Started and restarted several times. Setup places a shortcut to a program on my desktop. Nothing happens when I click on this shortcut. The printer will print and scan to computer works. What kind of program the shortcut is pointing to and how to operate / or do I need?

  BTW the shortcut in the start menu that points to the same program does not work.

  Hello

  Solution follow below to install the hotfix, and then double-click the HP Photosmart 7520 icon and check differences:

  http://support.HP.com/us-en/document/c03640384

  Kind regards

  Shlomi

• Logitech h340′s headset does not install correctly. "Unknown device".

  I use Windows 7 and comes from my brand new Logitech h340′s headset to connect to the PC via the USB port. Unfortunately, the device is not recognized and the driver so do not install automatically, so I can't use my headset.

  Here is the message I get:

  "Unknown device".

  "Windows has stopped this device because it has reported problems. (Code 43) »

  Then when I try the convenience of Windows it tells me that 'the best driver for your device software is already installed. Windows has determined the driver for your device software is up-to-date. »

  Device type: Bus USB controllers
  Manufacturer: (host controller USB Standard)

  I tried to restart, but it still does not work.

  All Windows updates have been installed.

  I really don't know what to do to be able to use my newly purchased helmet.

  Thanks in advance for your help.

  Hello Soraya,

  Thank you for reaching out to us on Microsoft Community.

  Before I can give you some suggestions to solve this problem, I want to collect the following information from you:

  • What is the brand and model of your computer?
  • Significant changes have been made on the computer before this problem?

  I would like to inform you that, "Windows has stopped this device because it has reported problems. (Code 43)" may occur if the peripheral equipment fails or if the device driver fails.

  Step 1.

  I suggest you follow the steps in the following link:

  http://TechNet.Microsoft.com/en-us/library/cc725873 (v = WS.10) .aspx

  See: Also the error codes in the Device Manager in Windows

  Step 2.

  As all devices have same also have USB device associated drivers. Appropriate sometimes drivers not detected after initial installation so reinstalling the drivers can fix the problems.

  You can check after uninstalling and reinstalling USB drivers if you are able to connect. You can disconnect all USB devices and then perform the following steps:

  • Click Startand then click Control Panel.
  • Click system and Maintenance, click System, and then click Device Manager.

   

  Note: If the control panel is in Classic view, double-click System and then click on Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  • In Device Manager, double-click to expand the 'Bus USB controllers', right click on the controller host, click "Uninstall" and click "OK".

  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.

  • Repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

  Do get back to us and let us know the State of the question in the case where you need further help or your next post. We, at tender Microsoft to excellence.

• All-in-one HP 6525 does not install correctly

  Hello and hope you can help me. I tried looking for the answer to my problem in the previous posts of the forum but could not find anything useful for me.

  I bought the printer about a month ago, I installed it without any problem (wireless), but at some point, I couldn't use the scan function. I had to use the USB connection to make. I thought about uninstalling resettlement of amd, but several problems have emerged. Now, I can not install all the features, scan function does not work wireless, not to mention eprint. I have removed all HP registry keys before reinstalling the software still does not work. When I get to the control network environment, the program blocks. The printer is connected to the wireless network, it shows even documents.

  Please, can you help me?

  Hi @ionelaiordan

  I understand that you have already uninstall it and tried to install it, but the following steps may resolve the software questions have expressed you;

  1. Hold down the Windows Logo key () on the keyboard and the 'R' to open the dialog box run, type %temp%

  2. Delete all files and folders in the temp folder. Choose Skip if all pop ups seem to say all files cannot be deleted

  3. The new software - uninstall the printer software Instructions

  4. Once the uninstall is complete, reboot the computer

  5. Follow these steps to reset the registry settings and options for Windows Installer.

     • Hold down the key of the Windows Logo on the keyboard and the 'R' to open the dialog box run

     • In the Open box, type msiexec /Unregister, and then click OK.

     • Hold down the key of the Windows Logo on the keyboard and the 'R' to open the dialog box run

     • In the Open box, type msiexec/regserver, and then click OK

        * Note: there is a space between the c and the /.

        

       If you do not at this stage, use this link to perform another way. Restart Windows install

  6. Run the system Accessories\ tool disk cleanup <> How to delete files using disk cleanup

  7. Download and install the latest version of Adobe flash player http://www.adobe.com/support/flashplayer/downloads.html

  8. Perform a clean boot > How to perform a boot in Windows

  9. Download the following SP40669 file download - if this download and or install, please proceed to the next step.

  10. Disable real-time scanning and the firewalls; The image below is an example of McAfee, if you have another antivirus program and need help to disable the analysis in real-time and firewall let me know.

      

      Source of the image

  11. Download and run the HP printer install wizard for Windows

  The HP printer for window installation wizard was created to help Windows 7, Windows 8, and users Windows 8.1 download and install the latest and most appropriate HP software solution for their HP printer.

  Please let me know the results of these efforts.

• 11.0.2 MSI does not install correctly

  So I downloaded the latest version of the software Adobe Reader 11.0.2. I have extraced content and edited the MSI file by using the Adobe Customization Wizard.

  My question is this. When I install it using the command msiexec /i file.msi /qn TRANSFORMS = file.mst it will install Adobe Reader 11.0.0 with all the customizations that were created in the .mst file. Why is it not install 11.0.2? If I run the .exe file it installs 11.0.2 but if I run the .msi file it installs only version 11.0.0. Any help would be great. Thank you.

  The way I apply the transforms and install 11.0.02 after AdbeRdr11002_en_US.exe ,.

  1. apply the following extraction, to extract all the deliverables in AdbeRdr11002_en_US.exe,

  "AdbeRdr11002_en_US.exe - sfx_o""-sfx_ne "

  -do not forget to no space between the path of the folder _sfx_o and extraction, quote is required if--

  for example if the extraction folder path is "c:\abc", then command would look like this,

  AdbeRdr11002_en_US.exe - sfx_o "c:\abc" - sfx_ne

  2. This will extract the following files in "c:\abc."

  ABCPY. INI

  AcroRead.msi

  AdbeRdrSecUpd11002.msp

  AdbeRdrUpd11001.msp

  Data1.cab

  Setup.exe

  Setup.ini

  3 use A11 Customization Wizard to customize Setup according to your need, then save the package to get the AcroRead.mst file

  4. Once you have ready transformations, use the following command to install 11.0.02,

  "msiexec /i AcroRead.msi PATCH =";" Transforms = "AcroRead.MST" "

  Hope it helps!
  

  Post edited by: Subrato Namata

• Driver does not install correctly

  This device is not configured correctly. ___There (code 1) is not selected for the device information set to pilot or element.___To reinstall the drivers for this device, click on reinstall.

  This device is not configured correctly. (Code 1)

  There is no driver selected for the item or a set of device information.

  To reinstall the drivers for this device, click on reinstall.

  Hi Mzpurple2u,

  Until solve us the problem we need more information on the issue.

  ·        When and where exactly you see this error message?

  ·        Which is the device that is causing this problem?

  ·        The device works much earlier on this computer?

  ·        You did changes to the computer before this problem started?

  Error code 1 mean that the system was not the ability to configure the device.

  However, you can verify which is the device that is causing this problem and post back the result.

  You can also try to update the drivers for the device in Device Manager and check if that helps you solve the problem. Access the link below and follow the steps to update the drivers.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.