Driver does not install correctly

Similar Questions

• Downloaded Driver does not install correctly

  Print HP 2410 died, but everything on my pc and the set up worked well.   I got the used 2610xi.  I removed the 2410 and tried the disc to instal 2610... She has no cause not windows 7... closed it... went to HP.com and download the driver and 5 updates and then install the driver that seems to be okay and then I did the updates... few of whom said there was no driver for updates to update.   Then I got a message for my PC. I did and then she was installing drivers for, while... and there was a box filled showsing but the last line that says driver failed... but printer showed that he and ready.  I did a scan and it scanned for connection was good... but it would ' t print!  Whenever I hit print it says that I should open a "note" to use this feature...   On the line and went to find this post http://h30434.www3.hp.com/t5/Scanning-Faxing-and-Copying/can-t-install-software-for-all-in-one-photo...   so I followed what was said exactly... I removed the 2610, I unplugged the USB printer cable, I have reboted PC, I extracted the file of the pilot... and he showed extraction... then more NOTHING... hard drive is swirling as something that happens, but he was 15 minutes now... show nothing.    I have a fast modern PC... nothing takes this time who is going to work.    I confirmed from the properties of my computer I have Windows 7 64 bit... my PC and printe rset up has worked well with the 2410 until he broke.    Never had so many problem setting up a printer.  HELP Please

  Hi Notanother1,

  Thank you for your answer! What happens when you use the printer HP install wizard for Windows, does make a difference?

  Hope to hear from you and have a great day!

• Microsoft Update for hp LaserJet 3015 PCL 5 driver does not install in Windows 7

  I use Windows 7 update.
  Microsoft Update for hp LaserJet 3015 PCL 5 driver does not install. He says 1 optional update is available almost every day, then when I try to install, it does not install and it says that the update is not necessary. Even once when I check updates, it says 1 optional update for the printer is available from Microsoft. And the story continues. I tried to reinstall the optional update, but the same problem persists perennielly

  Is this the driver you are looking for?
  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=503519&prodTypeId=18972&prodSeriesId=503548&swLang=8&TaskID=135&swEnvOID=4062

  Looking for HP for the pilot because it is better to get these live drivers from the manufacturer. TaurArian [MVP] 2005-2010 - Update Services

  No, these aren't the droids, uh, I mean the drivers he was looking for.

  In fact, it's better to get the new drivers from the HP website, you will notice the link you provided that the options only are available for this printer under Windows 7 drivers universal. I regularly have problems with universal drivers and strongly recommend to avoid as much as possible.

  I agree with the question of the original poster, which, after more than two years, remains unanswered by Microsoft. It seems that MS has a driver PCL 5 (not universal) updated specific 3015, but it fails to install the Windows Update control panel. I finally gave up on it, right click on the update and selected the option to hide it from view.

  Why bother with a solution when I use the button "Sweep-It-under-the-carpet" practice of Microsoft?

• Driver does not load correctly

  Some time previously, I've updated my HP Officejet 6480 all in one software and since then, the drivers do not load correctly.  Whenever I start my computer I get an error while loading programs are.  It is said that a driver has not loaded correctly.  I am running Windows 7 home.  It may have started when I upgraded to Windows 7, 64-bit XP and loaded the new software from the HP website.  I don't remember exactly.  Today I tried to send a fax from the solution Center and found that the "Send a fax" button is irrelevant.  Since I am able to send faxes from the buttons on the front panel on the printrer, I guess that the driver does not properly is the fax driver.  All other functions work.  I uninstalled the software from the control panel in Windows 7 and downloaded and reinstalled the software several times without success to resolve this problem.  Any ideas how I can fix this problem?  Thank you.

  Hi Dave46a,

  Welcome to the HP Forums!

  I see that you have trouble to install your HP Officejet 6480 to your Windows 7 PC.

  I would try the following:

  1.) use Microsoft Fix It to uninstall the software. Select Windows, click on install or upgrade software or hardware, click on install or remove programs, and then click Run now next to correct problems that programs cannot be installed or uninstalled. (Use this to remove the printing software).

  2.) try using the printer HP install wizard for Windows for the re - install.

  (3.) to run the HP print and Scan Doctor to see if other errors occur.

  Hope this helps and have a nice day.

• 2013 redistributable Visual Studio does not install correctly

  After you install our program on a computer laptop users and attempt to run the application, we see this error message:

  "The procedure entry point? Bios_base@STD@@QBE_NXZ is not found in the MSVCP120.dll dynamic link library. "

  For the record:

  1. Our Installer includes the Redistributable 2013 package.
  2. The redistributable package has been executed and reported success
  3. The redistributable was for the good (vcredist_x86.exe) target for the Win32 application.
  4. A run the stand-alone redistributable package it reported success, but the same error message is displayed when you attempt to run the application.

  The corrective action that actually worked was:

  • delete MSVCP120.dll delinquency
  • run the uninstall of the redistributable
  • Re - install the redistributable

  The application worked.

  Now for the questions.

  1. What happened to install it? I seems to work but does not work.
  2. What should I change to ensure that it works for all customers?

  Hello

  Thanks for posting your query in Microsoft Community.

  The question could arise if the redistributable is not installed correctly or corrupted package installed. If you get the number again, you can follow the steps provided below:

  Method 1:

  a. click Start, right-click computerand then click Properties.

  b. in the name computer, domain, and workgroup settings , click change settings.

  (If you are prompted for an administrator password or for confirmation, type your password, or click continue.)

  c. click change settings , and then select the Advanced tab click the environment variables button.

  d. the user variables area, click on TEMPand then click change.

  e. in the Variable value box, type C:\Temp, and then click OK twice.

  f. click applyand then click OK.

  g. follow steps 4 to 6 for the variable of environment TMP as well.

  h. confirm this folder C:\Temp exist, otherwise create a.

  i. restart the computer.

  j. attempt to install the application again.

  If the steps do not help, try the next method.

  Method 2:

  If you are comfortable in changing some registry settings, then follow the steps provided below.

  1. Click Start and type run in start search box, and then press enter.
  2. Type regedit and click OK.
     Registry warning:
     Important: This section, method, or task contains steps that tell you how to change the
     Registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 KB
     How to back up and restore the registry in Windows
  3. Go to HKEY_CLASSES_ROOT\Installer\Products\F942F94A19C0F79468FD2B85E5E8677B
  4. Right-click on this registry entry, and then click Rename.
  5. Rename F942F94A19C0F79468FD2B85E5E8677B to -F942F94A19C0F79468FD2B85E5E8677B.
  6. Close the registry editor.
  7. Restart the computer.
  8. Check if you are able to install the application.

  If the method does not resolve the problem, continue to the next method.

  Method 3:

  You can also reinstall Visual C++ Library Runtime components to solve the problem.

  You can uninstall all existing Microsoft Visual C++ Redistributable Package and install the Microsoft Visual C++ Redistributable Package 2013 and check if it helps.

  Step 1: To uninstall the package:

  1. Open programs and features, click Start > Control Panel >programs and features.
  2. In the list, find the Package redistributable Microsoft Visual C++ and click on it.
  3. Right-click on it and select Uninstall.
  4. Restart the computer.

  Step 2: Download and install the package and see if it helps.

  Click on the link below and install it in your computer.

  Package redistributable Visual C++ to Visual Studio 2013

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• 6110 driver update does not install correctly

  I had XP drivers for 6110 all-in-one printer installed and running - 09/03/2003 - V 2.4.1.8.

  I went to the page "HP Officejet 6110 all-in-one printer drivers", HP Officejet basic driver, under "Driver - software product (3) installation" saw that - 2009-09-12, Version 4.2.1 (34.23 M) was the last version recommended, so I downloaded to a folder on my C: drive.

  I ran / run the file downloaded in this folder, but the wizzard installation only got during most of the first two of the four elements-ball before he stopped. Apparently, it uninstalled my original driver as the new hardware detected msg appears and calling "Print" of an application has not found the 6110 options of the printer. So I rebooted the system and run the installation file downloaded driver in the same folder again. This time, it appeared to get through most of the four bullets-Articles of the wizzard, and when I tried to print from an application, he finds the 6110 printer, but with a completely different interface. However, when I went to Control Panel / administrative tools/Device Manager and checked the current version of the driver for the 6110, it showed 14/10/2002---2.0.0.134, an older version of what I had previously.

  Since there is no instruction 'on-screen', I got aware of the printer and the USB connected all the time.

  What happens and how can I get the latest version of the driver to install properly? My motive in update was for further selection options to correct paper for the newest Premium HP Photo papers which I couldn't on my original driver version, or (obviously), I see on the old version 2.0.0.134.

  Thank you, Waterboy71,

  As I did not have an immediate response, I've resorted to trial and error and came up with the same solution you suggest - i. e., downloading and installing the long SW and pilot w/cables etc seconded. He was soft - installing the cables being detached probably being the cure for my original problem in the installation...

  Which leaves me with the same driver I had initially - i. e., 09/03/2003-V 2.4.1.8 (and what seems to be a large number of additional baggage - files in C:\temp, which I don't remember in my original version of work) that is better than going backwards.

  I'll just keep trying by trial and error to get the best quality using ink HP and HP Premium Plus Photo Paper photo prints, as advice from HP for this product of revised on printers before 2009 document is to use a selection that does not appear with the V 2.4.1.8. driver/sw - i. e., select 'Advanced Mode '. But I am familiar with all the things HP has said about this document updated the and I will work.

  I will say that the download page for 6110 drivers need to edit to avoid confusion even for others. It offers three choices for the updated drivers - i. e., 1) HP Officejet basic driver (34MO), 2) HP multi-function products driver Bundle - Corporate only (69 MB) and 3) HP Officejet and PSC full feature software and driver (166 MB). However, after getting the first to install, I found that it installed the old driver and all documents supporting documents and references for the company, small footprint, version - not what is implied in the description and date/version of the first and reasonably inferred from the comment on the second object the corporate package. It seems that the incorrect file name is attached to the first choice, but I did not load the second to see what happen (but maybe I'll do that on a lazy day). Someone should check all three and make descriptions in line with pilots produced on download...

  Anyway, thanks again and I'll mark the issue as resolved.

  John

• Satellite P10 824: modem driver does not install

  I have a tosiba Satellite P10 824 and the modem driver not install what can I do? This page driver is installed but the modem does not work.

  Hi Cienciala

  If the reader is already installed and the modem is correctly listed in the Device Manager, do not try to install it again and again. I advise to enter the properties of the modem in the device and on the diagnosis tab Manager list, you can use Query modem and verify the results.

  If the modem does not work it may also be the configuration dial problem.
  By the way there is also a useful site, you can check http://support.toshiba-tro.de/kb0/FAQ35006G000UR01.htm

• Silverlight does not install correctly and be unistal not at all what should I?

  Silverlight has never installed correctly and when I bilel uninstall under programs it shows and white sheet of paper as an icon and no memory used, when I try to uninstall to do a fresh install, because udates won't take it says it cannot uninstall due to the fact that it is not able to match or find the file adiquit.  I can not it turned off my computer so I can put it right and now I can't watch netflix.  Please help :)

  Hi Nicole,.

  Please see the center of support of Silverlight here: http://support.microsoft.com/ph/12929#tab0 where there are different ways to get help (self-help, assisted support, community & forums, resources, or contact technical support (but the latter is probably costs money unless you meet certain specific criteria)), if you can't find what you need to get their resources , and then search the forum and if you still don't have an answer, post a question in the forums where experts on this program will provide assistance best we can because that's their specialty.  While we try to cover some Silverlight questions here in the answers (even if it's the wrong forum even for that), we do not have the dedicated experts that they do in their own forums.

  As alternative, if this does not help, and I'm not 100% sure since while I used it successfully for hundreds of other programs and the only ones where I had problems and kidnapping special tools were also some deep-seated AV Suites, I never really tried with Silverlight, but you can try Revo: http://www.revouninstaller.com/revo_uninstaller_free_download.html in Advanced Mode and see if that helps.  It often does the trick when the normal uninstall process fails for some reason any.  And because it does a better job, that's how I always uninstall anything I install to keep my cleaner system and do a better job preventing the remnants of disenfranchised (and my experience says that virtually every uninstalled program leaves in the normal way of things behind this Revo intercepts and removes).

  I hope this helps.

  Good luck!

• Logitech h340′s headset does not install correctly. "Unknown device".

  I use Windows 7 and comes from my brand new Logitech h340′s headset to connect to the PC via the USB port. Unfortunately, the device is not recognized and the driver so do not install automatically, so I can't use my headset.

  Here is the message I get:

  "Unknown device".

  "Windows has stopped this device because it has reported problems. (Code 43) »

  Then when I try the convenience of Windows it tells me that 'the best driver for your device software is already installed. Windows has determined the driver for your device software is up-to-date. »

  Device type: Bus USB controllers
  Manufacturer: (host controller USB Standard)

  I tried to restart, but it still does not work.

  All Windows updates have been installed.

  I really don't know what to do to be able to use my newly purchased helmet.

  Thanks in advance for your help.

  Hello Soraya,

  Thank you for reaching out to us on Microsoft Community.

  Before I can give you some suggestions to solve this problem, I want to collect the following information from you:

  • What is the brand and model of your computer?
  • Significant changes have been made on the computer before this problem?

  I would like to inform you that, "Windows has stopped this device because it has reported problems. (Code 43)" may occur if the peripheral equipment fails or if the device driver fails.

  Step 1.

  I suggest you follow the steps in the following link:

  http://TechNet.Microsoft.com/en-us/library/cc725873 (v = WS.10) .aspx

  See: Also the error codes in the Device Manager in Windows

  Step 2.

  As all devices have same also have USB device associated drivers. Appropriate sometimes drivers not detected after initial installation so reinstalling the drivers can fix the problems.

  You can check after uninstalling and reinstalling USB drivers if you are able to connect. You can disconnect all USB devices and then perform the following steps:

  • Click Startand then click Control Panel.
  • Click system and Maintenance, click System, and then click Device Manager.

   

  Note: If the control panel is in Classic view, double-click System and then click on Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  • In Device Manager, double-click to expand the 'Bus USB controllers', right click on the controller host, click "Uninstall" and click "OK".

  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.

  • Repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

  Do get back to us and let us know the State of the question in the case where you need further help or your next post. We, at tender Microsoft to excellence.

• Re: Value added package does not install correctly

  Hello!

  All of a sudden my media keys stopped working.
  I did not any changes made to the system installation of VMware exept. I tried to uninstall value added package, erased reg with CCleaner, then reinstalled VAP.
  Have made several times!

  Still does not work! My PC is Qosmio X 300-12 H and it works on Windows 7 64-bit.

  PS so far worked flawlessly (mute, lights, camera, dolby) I don't know what happened!

  Suggestions please!

  Stand by.

  A VAP Setup completed correctly or not, or you can not see flash cards when you press the FN key?

• 7520 photosmart all-in-in-one: software does not install correctly

  I have installed and uninstalled 3 or 4 times. Started and restarted several times. Setup places a shortcut to a program on my desktop. Nothing happens when I click on this shortcut. The printer will print and scan to computer works. What kind of program the shortcut is pointing to and how to operate / or do I need?

  BTW the shortcut in the start menu that points to the same program does not work.

  Hello

  Solution follow below to install the hotfix, and then double-click the HP Photosmart 7520 icon and check differences:

  http://support.HP.com/us-en/document/c03640384

  Kind regards

  Shlomi

• USB for C7280 driver does not install on a laptop HP DV8-1093 running Windows 7PRO

  When I plugged my C7280 to an HP Desktop running Windows 7 Pro 64 immediately I had an advertising icon that the drivers are loading it takes 5 minutes and several drivers have been installed, I can print and scan

  on my laptop DV8-1093 is also running windows 7 64 pro, when I connect the USB cable nothing happened, no icon in bottom right and no driver s are installed, I check the cable that he works on the desktop

  WHY drivers won't load

  What can I do for installing the drivers

  Thank you

  François

  Hi frmichaud,

  I understand that the software was not automatically installing for the HP Photosmart C7280. I'll try my best to help you with this problem. The software and drivers are not previously installed on the laptop.

  Here is the download page for software HP Photosmart full feature and drivers, download and save to your desktop.  Follow the steps described in this document for the installation of the printer software in Windows 7 for a USB cable connection. Make sure you unplug the USB cable from the computer and wait that you asked before you plug it into the computer.

  I hope that this information help, please let me know how it goes.

  Thank you

• Optiarc DVD RW AD7710H driver does not install

  Separated from this thread.

  I have exactly the same problem with my Optiarc DVD AD-7710 on Sony laptop and I also uninstall and sought changes to the equipment and the updated driver to update, but unfortunately the problem was not solved at all. The problem started recently without doing anything. Seems that some update in the operating system or the driver caused this problem to be happen. Material to DVD does not have no problem because I can boot my laptop with kaspersky rescue CD and then I see the content of the CD but when windows 7 is driver problem happen.

  Please help me if any body has resolved the problem.

  I did what you said above (all points) but the problem was not solved, fortunately the problem was solved by downloading Microsoft DVD fix tool "MicrosoftFixit.dvd.MATSKB.Run.exe" and run it.

  Please say the same for others who has the same problem.

• All-in-one HP 6525 does not install correctly

  Hello and hope you can help me. I tried looking for the answer to my problem in the previous posts of the forum but could not find anything useful for me.

  I bought the printer about a month ago, I installed it without any problem (wireless), but at some point, I couldn't use the scan function. I had to use the USB connection to make. I thought about uninstalling resettlement of amd, but several problems have emerged. Now, I can not install all the features, scan function does not work wireless, not to mention eprint. I have removed all HP registry keys before reinstalling the software still does not work. When I get to the control network environment, the program blocks. The printer is connected to the wireless network, it shows even documents.

  Please, can you help me?

  Hi @ionelaiordan

  I understand that you have already uninstall it and tried to install it, but the following steps may resolve the software questions have expressed you;

  1. Hold down the Windows Logo key () on the keyboard and the 'R' to open the dialog box run, type %temp%

  2. Delete all files and folders in the temp folder. Choose Skip if all pop ups seem to say all files cannot be deleted

  3. The new software - uninstall the printer software Instructions

  4. Once the uninstall is complete, reboot the computer

  5. Follow these steps to reset the registry settings and options for Windows Installer.

     • Hold down the key of the Windows Logo on the keyboard and the 'R' to open the dialog box run

     • In the Open box, type msiexec /Unregister, and then click OK.

     • Hold down the key of the Windows Logo on the keyboard and the 'R' to open the dialog box run

     • In the Open box, type msiexec/regserver, and then click OK

        * Note: there is a space between the c and the /.

        

       If you do not at this stage, use this link to perform another way. Restart Windows install

  6. Run the system Accessories\ tool disk cleanup <> How to delete files using disk cleanup

  7. Download and install the latest version of Adobe flash player http://www.adobe.com/support/flashplayer/downloads.html

  8. Perform a clean boot > How to perform a boot in Windows

  9. Download the following SP40669 file download - if this download and or install, please proceed to the next step.

  10. Disable real-time scanning and the firewalls; The image below is an example of McAfee, if you have another antivirus program and need help to disable the analysis in real-time and firewall let me know.

      

      Source of the image

  11. Download and run the HP printer install wizard for Windows

  The HP printer for window installation wizard was created to help Windows 7, Windows 8, and users Windows 8.1 download and install the latest and most appropriate HP software solution for their HP printer.

  Please let me know the results of these efforts.

• software for the printer driver does not install

  My printer is C7100 all-in-one.  My OS is windows 7 - message comes back "could not install any software.

  I recommend traverse "Programs and features" in your control panel and manual uninstall of the printer, then shut down and restart your computer. If the files do not uninstall, then you can have a deeper problem with your operating system.

  Once the software is missing, try again after the above link and by installing the full setting software.

  Let me know!