Really confused to not see a parameter

Similar Questions

• Software JetDirect 380 X can not see the airport card in the laptop G4 PPC

  Hello

  I tried to add a customer to the airport. It's a LaserJet 1200. But the software that comes with the JetDirect tells me to install an Airport card in the laptop. Now I can join hpsetup and print to the LJ 1200. But in practice I have to disconnect from the internet and the map Airport.  So, I know the JetDirect and LaserJet 1200 work very well. I tried different settings on the airport, but nothing has really changed the software on the laptop not finding the Airport card.

  Now I have a WOW goes a Xsense MIH 130 Xrouter, then go to the Airport Express Terminal. All Mac desk top of page 933mh, 1.67 ghz powerbooks. I use OSX10.4 to 10.5.8.  I don't know if the router is the problem or if the parameter in the jetdirect should be changed to the ad-hoc to something else. Don't know how to do this. With it, do not see the map Airport, I can't do the enbedded 192.0.0.192. There are a lot of maybe if I do this or if I do this it might work. Since the configuration of the printer in the TCP/IP section page everything below the line, Config by: is not specified.

  Thanks for any advice.

  Well again I was able to get to the stage 1.6 (in 10.5.8 printing Center is not the same). I could remove the printer that was working on its own network of HP. But was unable to add a printer in 0SX 10.5. Perhaps through IP printing, but do I put as the address? It is the site of HP to get instructions on a 380 X and another printer.

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=en & CC = US & TaskID = 115 & prodSeriesId = 29789 & prodTypeId = 18972 & prodSeriesId = 29789 & objectid = c00257796

  Maybe I should to the left of the printer, but I've changed the SSID in the jetdirect to match the network. The IP printer 192.0.0.192 or 192.0.0.193 or just use the network name it was changed to?

  To close, but I thought a few times.

• DirecTV DVR not seeing internet via router TC

  I installed a modem Arris SB6183 on Comcast xfinity network.  The modem is turned on and connected to the network, xfinity without problem.  All my other devices connected to the TC and could see the internet without problem.  (Though, as I write this I realize that they were all apple devices.)  However my Directv DVR (HR44-500) did not see the internet via the wireless or ethernet cable.  My TC is a 3 TB A1470.  The installer has been in DHCP + NAT.  I also tried to give Directv a (local) fixed IP which address found DVR, but still couldn't find the internet.  When I plugged the DVR directly to the SB6183, without going through the TC, he saw the internet seems to indicate a problem of TC.

  After a few days of futile efforts, I have reconnected the router xfinity and replace the TC in Bridge mode.  Everything is working now and the DVR sees the internet, but I'm still pay Comcast 10 $par month to rent their modem.

  Does anyone else have this problem?

  You need to clarify a few things.

  I would expect questions for Internet access to the DVR by the TC without doing manual port forwarding. The DVR itself must be connected to the internet as long as you have the correct values for IP etc. Although I suspect that ipv6 might complicate the situation.

  If the DVR awaits UPNP router compatible... the TC is a failure. Apple is not compatible UPNP, adopting instead their own port open NAT - PMP protocol which is limited to most of the time the Apple products.

  To get out, you need to return to the configuration without your xfinitiy router... and give us a stack of screenshot... To see the complete configuration of the RECORDER and the TC... screenshots are the best way to do it.

  DNS, in particular, can be a problem... so make sure you use Google public DNS on the DVR and see if that helps.

  Any other suggestions we really need to see all your settings...

  Some screenshots of a working Mac or iPad would also show the configuration of a unit of work... rather than the DVR has failed.

• Satellite Pro M70 does not see HARD drive sometimes

  Help me!

  My computer does not see my hard drive but see Installer and another computer.
  My hard drive is working and I put the new drive hard but computer does not see.
  And when I install XP on the computer I can see HDD format during the installation.
  And when prawns my computer I do not see the HARD disk again.

  Help me please

  Hello

  I think that it s a HDD issue naturally it s really strange that the HARD drive is different sometimes and sometimes it s is not visible, but I doubt that it could be software related issue. That's why I think that it s a drive HARD and in my opinion, you should check if other HDD SATA runs correctly.

  Good bye

• Satellite 1415 does not see HARD drive

  I just finished my old 30g HD to a 160g via a cable usb/ide on my Satellite 1415 cloning/adaptation.

  I've used Norton Ghost who said using the copy MBR 'not' option, I have to format the new drive. It took me over six hours to do due to overheating closed the first period which forced me to do it again.

  Now with the new full disk, I installed in the machine and starts, received a message "NTLDR is missing" on the first try. After going in (WinXP) disk management I noticed that the new drive was now three scores, two the same size that the old hard drive and the last not allocated. I looked at the files in the first partition and found that I do not need so I deleted the files and the partition. The remaining active partition has all the Po files, that I need so I have it assigned a drive letter.

  Now to start with the new drive I get missing operating system message. I ve changed the boot order and linked to the boot the ghost CD but had no luck with either. Of course the machine does not see the disk, so my question is how I can get to see the new drive letter to start when it seems now that for a C:\ drive?

  The only option I see in the BIOS is boot order change. Thank you

  Hello

  To better understand:
  The ability of the entire HARD drive is recognized properly?

  To be honest, the whole story is a bit confusing for me. I use Norton Ghost with WXP too and I know that you can create your own recovery image and burn on CD or DVD. This medium, that you can use to install an operating system.

  You can also save files to recovery on the second partition and then copy to external HARD disk.

  With the new HARD drive using Microsoft facilities CD and install WXP. Create own partitions on the new HARD drive and all ghost copies files to the second partition (new HARD drive). You may not install all driver and tools but install Ghost on this OS fresh and naked. Start the ghost and Recover My Computer option. So, after 20 minutes, you'll WXP as on the old HARD drive.

  I did it with my old Tecra.

• Import photos no problem can not see the photos on iPhone

  I upgraded my MacBook Pro to El Capitan.  Since moving from iPhoto to Photos (even before I updated the operating system) when I plug my iPhone 5 to import pictures in the selected library I do not see the photos appear in the import window so that I can select for imports.  I literally had to email it to myself, and then import it into the e-mail.  I work with different libraries within pictures, so I excluded it only love the library system.  Same result, can not see the photos.  Also, I have unplugged and replugged in and tried the other USB port to rule out hardware, while the Photos could force them to see the device as new, and that does not work either.  I tried something another user who had to open Image Capture to see if she could see all the pictures on my phone and it doesn't work, I found (theory was that opening would make Photos recognize as well).  However the Image Capture wouldn't add a USB scanner so I think it's not worthy of trust.  Photos only setting I have enabled is the automatic update to iCloud.  Otherwise, I don't know what another parameter to seek that could block it.

  When the phone is connected USB the phone reboot - many have found this will clear this problem

  LN

• Westell 7500 can not see AP wnr834bv2

  I had a nice home network consisting of a WGR614v5 in one place, powered by a 660 modem and a WNR834bv2 configured as an AP in a more convenient location to provide wireless connectivity to my wife and my laptop.  I could access both routers to change the configuration options (turn wireless switch) by their IPS (192.168.1.1 & 192.168.1.200 respectively).

  Then "lightning" stuck nearby and pulled the 660 modem and WGR614v5 router.  My provider was willing to replace them, but with a Westell 75002207 wireless modem/router combo.  The installation went well except, this unit converts all IP addresses, attached in 10.0.0.X.  The only device, it doesn't have to be converted was WNR834bv2 AP and it's because, I guess, he could not "see."  No matter how many times the new router 'scans', he never finds 192.168.1.200 (WNR834bv2).

  Because I, I can access is no longer (when you go away, I usually turn wireless off) by it of IP address of origin, even isolated from the rest of the network, or no matter what other 10.0.0.x I try within the new range of routers DHCP.

  Can someone help me understand why this is happening?  And by the way, the WNR834bv2 works yet it's wireless and wired functions perfectly well, I just can't get it.

  Signed, confused Gwlindq ;-)

  Yes, the problem is that (most likely the new main router) DHCP server is the allocation of units 10.x.x.x who cannot communicate with address 192.168.1.200.  To work around the problem of IP address, you need to set a static IP address on the device.  Simply plug wireless access point won't be enough in most cases.  Whenever I have install an access point, I always disabled the DHCP protocol to the access point in order to avoid any potential conflict.  In some cases, might manually configure the router DHCP pool and the access point to prevent its contradictory.  However, according labels what Netgear unit, I suspect you are routers in Garland instead of a router and an access point.

  The bottom of this document details how to set a static IP address in Windows XP.  Set the static IP address for 192.168.1.201 (No 192.168.1.200 as argued already) with the subnet mask that uses 192.168.1.200 (default should be 255.255.255.0).  Once the PC has a static address that works with the 192.168.1.200/255.255.255.0 access point, you should be able to access it, and then make the necessary changes.  Alternatively, you can change the new router to issue addresses in the 192.168.1.X/255.255.255.0 range, and it should work as it did before.

• I can not see some files on my network drive, but can browse their

  Hello
  One of our users are their files and missing files after the letter 'F' on their network drive. I checked on the server, and the files are missing on the server. However, I can browse to and open them. When I look in the windows explorer for this user, I do not see the folders and files passed letter 'F' But if I know the name of a file or folder that is there and manually type the name in the address bar, I can browse on him. For example, there is a folder named IBM. I see not the folder in windows explore. But if I type in the address bar (\\servername\username\IBM), I can see the contents of the file. If the files are there, but we cannot see them. So far only this user is having this problem isn't a question broad system.

  I activated the hidden file parameter and it is set to show the hidden files and folders. The server is a windows 2003 SP2 Enterprise

  Thanks for your help

  In the Explorer of-> tools-> view (tab), Folder Options->

  In addition to checking "Show the hidden files and folders", try unchecking the "Hide protected operating system files" two lines down.  It will ask if you are sure you want to do this - simply replies 'yes '.

  If it turns out that the system attribute has been applied to the file, you will not be able to change it in the Properties window.  You will need to use the "Attrib" command  See the following procedure article:

  «You cannow view or change the read-only or system attributes of folders... under Windows XP...» »
     <>http://support.Microsoft.com/kb/326549 >

  HTH,
  JW

• Operating system (XP) does not "see" CD player

  Hello

  I replaced a HD on old PC (Dell Dimension 3000) MOM and partitioned the new HD into two parts.  However,) -: and not C.  Now, the BONE is not 'see' the CD player! and I can not re - install b/c I can't access the CD player! I'm guessing that it is in some way caused the problem I checked almost all other including loose connectors, update BIOS, drivers, etc etc.  Anyone have any ideas? Thanks in advance

  Re-install (Clean) are by booting from the CD drive. You should be able to boot from the CD drive, to remove existing partitions. Create that one partition (doesn't have to be the size of the disk), install XP on this partition and then after installation of XP use 'Disk management' to create the second partition of the "Unallocated" space remaining and assign a name and the volume drive letter.

  You may need to activate XP by phone this time I provided what you need to know below.

  ==============================================================================

  How to activate Windows XP
  http://support.Microsoft.com/kb/307890/en-us

  See the section titled: "how to activate Windows XP by phone.
  Also, make sure that you do not confuse the product key numbers and letters
  (number 8 for the letter B, etc.)

  Blank page to activate Windows in the wizard of Windows Product Activation
  http://support.Microsoft.com/kb/314935

  How to contact a Microsoft Product Activation Center:
  http://support.Microsoft.com/default.aspx/KB/950929/en=us

  Microsoft Activation centers worldwide telephone numbers:
  http://www.Microsoft.com/licensing/existing-customers/activation-centers.aspx
  (This site is for activating Volume License, but if you call, they will help you)

  The phone number is not working:
  Microsoft Wordwide contacts: http://www.microsoft.com/worldwide/default.aspx

  Once Windows activated / Genuine Advantage Notifications:
  http://www.Microsoft.com/downloads/en/details.aspx?displaylang=en&FamilyID=afd45b36-3d77-4259-801c-d31a9a90cdcf
  (This tool will confirm that the copy of Windows installed on your PC is genuine and authorized)

  J W Stuart: Http://www.pagestart.com

• Can not see the drive letter for Hammer 640 GB external hard drive

  I have an external hammer 640 GB drive (which has a Western Digital WD6400AAKS drive inside) with important data. When I connect to my computer (under Windows XP Pro), I can see the player if I go to my computer-> hardware-> readers but can see any drive letter.

  Even if boot disks using software such as Hirens boot and demarrer start with the BACK, do not see this drive (I tried A - Z).

  There is apparently no physical damage to the disk.

  Hello
  In this case, it seems to me that the drive itself is damaged. For this purpose, it is likely that there is no conventional solution through Windows itself.

  I suggest you seek a professional store of COMPUTING, or computer confidence. If information on this drive is still recoverable, it will probably take advice from specialized professionals and know how to do really.

• installation does not see the printer when I plug

  I have a printer HP LaserJet, 1006 running on a Windows XP 32 - bit attached to a USB1 port system. I have no USB2 ports. The printer works fine, but the drivers are up to date. I downloaded the file (hp_LJ_P1005_P1505_Full_Solution_ROW.exe) and when I run it, and it gets to the point where it tells me to connect my printer, I plug in and turn on and nothing happens. Apparently the installer does not see when I turn on my printer. The problem would be that it is plugged into the port of USB1 and if so what do about it?

  Sorry must have misread your first message.  Before trying to reinstall the software, make sure that the printer and the old software is uninstalled.  The installer can be easily confused by older facilities, in order to ensure that those who are cleaned before installing the latest orders.  Hope that helps.

• Why can I not see the files I back up by using the backup and restore of Vista

  Can someone help me?  I have a Dell Inspiron 1525 and implemented backup and restore feature Vista so that every Sunday he automatically backs up my computer to my external drive.  I was on the computer when he said it starts up and that upward was completed successfully.  I assummed everything was fine until today when I show my father my drive external and noticed that none of the backup of files were there... or at least I did not see them.  The only files on the disk were the ones I put manually on here from my old computer.  I then ran a manual upward using Vista and again it says backup successfully completed.  I then watched the external hard drive and once again no new files.  The strange thing is the back up and restore program shows all the dates he has saved and also allows me to restore files from the back to the top.  To do this, I deleted a file I didn't really need out of my hard drive and then is gone to restore program and found the file and restored.  Problem is that the program does not say where he makes the file from.  What is going on?  Are backup files of certain types of hidden file I don't see unless I use the backup and restore program under vista?  I am currently running Vista Home Premium on a 32 bit system and the external hard drive I have is a Western Digital My Book Essential Edition.

  Windows backup is stored in a folder with the same name as your computer.  Open a command prompt and type echo %ComputerName% or startup, right-click on computer, properties.  You should see that % ComputerName % folder on your external drive, and in this context, a backup set. Steve Hebert - MVP Microsoft Internet Explorer

• Network printer does not see my Mac, running OS 10.8.2

  My Envy 411D all-in-one printer is not 'see' my laptop (macbook pro 2012).  I can print from the computer to the printer, but is not possible scanning in both directions, from the printer to the computer and vice versa.  I get an error message - communication error.

  The scan function shows computer of my spouse, but not mine (we are Mac OS 10.8.2 on MacBook Pro laptops).

  It's already happened and for me, the only way around him, needed to take several hours to reinstall the printer software.  When you do this, HP treats you like a re-registration of customer and applications quite new and all that.  We are already registered, however.

  So please advise me me, I would like to know an easier way to get the functionality I expect from this device.

  Thank you.

  Best,

  Anne Mowat

  [email protected]

  Indeed, it might be your router and use WEP security.  WEP is not really security because it can be broken with freeware within minutes.

  Pass the security of your router to WPA with a password you create.  While you're here, change the channel to 11 on 2.4 GHz router mode.

• Install HP does not see the printer in network, Windows DOES. Help!

  Hello

  I am trying to add my HP Officejet k8600dn to Windows 7 (32 bit) so I can scan, but the HP Installer (add device) can not see the printer. The unit is set up by cable to a switch on my network via an ethernet cable. If I go into the menu "Add a printer" Windows, I can install the printer very well. But I have to be able to scan and I don't know what to do.

  Tips on getting functional analysis if the HP software is unable to see my printer? Subnet mask and gateway on the printer are the same for the computer and the printer. I typed the correct IP address in the "Add a device" menu of HP, but he sees not just it. ARRGG!

  Thanks for any help!

  Hello

  I think that there is some confusion because the Officejet k8600dn is only a printer, it is not a multifunction device and does not provide the capability of scanning.

  You can find the specifications below:

  http://support.HP.com/us-en/document/c01287217

  If you have any different model printer, please specify the exact model.

  Kind regards

  Shlomi

• BlackBerry smartphones can not see the maps on my "BOLD"?

  Hello

  I just theBold on Orange in the United Kingdom and I do not see the maps app anywhere.  I can see it listed as version 4.6.0 under the list of Applications but can not see the software somewhere?

  I'm mean't to enable it somehow?  Also can not get the GPS function works as it says "failed to update GPS location" when I click on refresh?

  Any help would be really welcome

  If your provider blocks the passage of the icon (like AT & T) to another theme (Options-> themes) and see if you can find it. You may also download. Check mobile.blackberry.com from your BB browser.