Reference Dell T5600 PERC H310 led connector

Similar Questions

• Reference Dell 2950 Perc 6/i Raid card device driver

  Good morning community, I'm trying to find the Dell 2950 Perc 6/i Raid adapter Device Driver for Windows 2008 R2 Standard OS. Thanks in advance for your help. Modem489

  You don't need to load a driver for the PERC 6 / i in Server 2008 or newer version, the driver is 'native' for Windows.  If you think that you need a driver, I suspect it is because you tried to install and it is not all discs.  If Yes, do not forget that PERC does NOT support RAID/JBOD, then you must configure disks to a virtual disk (VD, matrix RAID) before they can be presented to the OS.  It can be configured in the CTRL-R utility (be sure to check the boxes of progress/Initialize options too).

• Reference Dell R710 - Perc 6 / disc matrix (support 4 TB?), I supported

  Hi all

  Since then, we want to upgrade the hard drive 2 TB (3.5 inches) for a large as 3/4 to.
  Is there information on the matrix of disc official supported of PERC 6 / i?

  We use Seagate 2 TB 72kRPM (bought from Dell) on our R710 servers. If the PERC 6 / I can't stand 3 to/4 TB disk. Is it possible to order the H700 support 4 TB drive adapter?

  We have installed the latest firmware /bios,
  -Perc 6/i: 6.3.3 - 0002, A-00
  -System BIOS: 6.4.0

  Thank you and best regards,
  Caleb Wong

  PERC 6 does not support disks larger than 2 TB. The H700 is supported in the R710 and supports disks larger than 2 TB. I would not, however, use desktop or NAS drives.

• Reference Dell T610 PERC 6i - very slow RAID rebuild

  Hi all, I have a DELL T610 with a Controller PERC 6i with 4 x 1 TB SAS 7.2 K disks configured as a RAID6. 1 of the drives has failed, I installed the new drive, but reconstruction is only 44% after 36hrs! Why is it so slow? Any ideas would be greatly accepted.

  RAID 6 is well known for its performance of poor\slow. This is the only function is to be safer than RAID 5, not to be fast and cheap.  With parity RAID, to rebuild the whole picture.  They have been known to go for a week or more before they are finished, according to the size and speed of players.

  Kind regards

• Reference Dell PERC H310 drivers

  I want to install a Windows Server 2008 operating system on a new PowerEdge R420 and I need to install the drivers for the PERC H310 controllers but I can't find the drivers as the only windows setup exe files or DUP which doesn't help since I always is not a running operating system.

  Can someone please tell me where to find this driver or how to get around this problem?

  Thank you

  You can use the switch/extract for the DUP or you can use the 'hard drive' version (ZPE).  Since you didn't say what version of 2008 you have been installing, I took the trouble to post all the:

  2008 x 64:
  http://downloads.Dell.com/FOLDER02416320M/2/SAS-RAID_WIN_Driver_W2K8X64_1KH1G_6.802.21.0_A06_ZPE.exe

  2008 x 86:
  http://downloads.Dell.com/FOLDER02416311M/2/SAS-RAID_Driver_W2K8X86_M62KG_6.802.21.0_A06_ZPE.exe

  2008R2:
  http://downloads.Dell.com/FOLDER02416328M/2/SAS-RAID_Driver_W2K8R2_D5N8T_A06_6.802.21.00_ZPE.exe

• Reference DELL T420 - battery on PERC H710 adapter controller

  Hello

  I received a yellow warning

  Reference DELL T420 'Battery on PERC H710 adapter controller'

  What it means?

  What should I do?

  Order the new battery?

  It is a simple replacement mission?

  Is it essential?

  Update:

  test URL

  http://www.Dell.com/support/article/us/en/04/SLN130018

  Have nothing, everything seems fine now...

  Thank you

  It is normal so he can make a full discharge of the battery as part of his learning cycle every 90 days. Make sure that this isn't that. If this isn't the case, the reason, give it 24 hours. If it is fully charged, update the system (including RAID firmware, driver first) firmware. If not fully charged yet or it reproduces quickly, then replace the battery - power down to replace.

• Dell Perc H310 T420-compatible hard drives

  Hello experts,

  I have a server T420 with 8 Bay running 2 SATA 3 "switchable hot 5 Dell hard drives.  The controller is a Perc H310.

  I would like to know what kind of hard drives could be integrated into empty compartments. I would like to use non - Hot Swap as well to extend storage. Buy standard 3 "5 7200 RPM Sata Hard Drivies? Will it work?

  Thanks in advance. Appreciate your attention.

  Concerning

  Afreire,

  You can use enterprise class SATA disks up to 4 TB in the remaining locations. You will need to the carriers for the readers, even if they are non-RAID.   H310 controller supports the use of JBOD (just a bunch of disks) without having them in a RAID.   OpenManage them will see as non-RAID drives.

  Kind regards

• PERC H310 H710p migration

  Hello

  I'm not an expert in RAID configurations but I am in charge of server Dell T320 my company and we will replace the storage controller that comes with it (H310) with a PERC H710p. We have a configured RAID-1 and we will continue to use the two disks of same after migration. We will replace the controllers.

  I know I have to do a backup before you replace the Exchange, but we will lose the RAID-1 configuration and data (including the operating system) after migration? Or it will be transparent to the system after reboot?

  Where can I find a type of paper that could guide me through this process because I don't want to wreck anything.

  Thanks a lot for your help.

  Jorge

  Hello.

  It is advisable to back up your data before performing any maintenance task. Ensure that you have a backup is valid data. The PERC H710 P supports the migration of virtual disk controller PERC H310. As a best practice, make sure that the hard drives and firmware H710 P is up to date. Replace the H310 and update the H710 P firmware with the controller cables disconnected from the background. Stop the server and connect the cables of the controller in the background and then restart.

  Your RAID configuration can be transparent to the system or appear in a foreign configuration. Clear the foreign configuration through the utility OpenManage Server Administrator (OMSA) or Ctrl + R for the POST.

  I would like to know how it works for you.

• Reference Dell MD3200i correct editing with IP system and the NIC for faster network speeds

  Hi all

  I worked on this project for a while now. I did a lot of research and have contacted Dell several times. I need help.

  I have 2 sets of identical to use for Hyper-V clusters servers. We bought a Dell MD3200i in November, we also bought a Dell 5424 switch and a Cisco SLM2048 switch. These servers have Real Tek 2 network cards for iSCSI Jumbo frames is 9 k

  The Dell MD3200i is two SAN controllers. Dell 5424 is the iSCSI optimized switch and Cisco is a 48 switch ports. iSCSI is on its own network that nothing else is connected to it. (There is an Iomega NAS and a promise Vtrak SAN Tech with all current domain of execution with iSCSI controller)

  Reference Dell MD3200i controller 0 Port 0 192.168.130.101 controller 1 Port 0 192.168.131.101

  Controller controller Port 1 0 192.168.130.102 1 1 192.168.131.102

  Controller controller Port 2 0 192.168.130.103 1 2 192.168.131.103

  Controller controller Port 3 0 192.168.130.103 1-3 192.168.131.104

  Cisco switch has 1 VLAN n ° 1 on it and the 130 subnet inside elements. There are 8 connections to the switch. 4 controller 0 and 1 of each of the servers. It has an IP of 192.168.132.4, but that switch IP does not make difference. Lighted Jumbo frames

  Dell switch has 2 of #1 for various things such as the domain controller, Vtrack, and SIN. Subnet 2 is 131 and has a total of 8 connectors inside. 4 in 1 controller and 1 from each of the servers. Lighted Jumbo frames. The switch IP address is 192.168.132.2

  Groups of servers. Each server node running Windows 2008 R2 SP1 and running hyper-v with virtual server clusters / storage folder on them. 2 Realtek NIC with Jumbo frames made 9 k ProdNode1 and ProdNode2 have 12 Core i7 CPU with 12 GB memory, EXNode1 and ExNode2 have 12 Core i7 CPU with 24 GB of memory.

  ProdNode1 iSCSI-1 192.168.130.110 ProdNode1 iSCSI-2 192.168.131.110

  ProdNode2 iSCSI-1 192.168.130.120 ProdNode2 iSCSI-2 192.168.131.120

  ExNode1 iSCSI-1 192.168.130.130 ExNode1 iSCSI-2 192.168.131.130

  ExNode2 iSCSI-1 192.168.130.140 ExNode2 iSCSI-2 192.168.131.140

  Portal discovery iSCSI on ProdNode1 went to 192.168.130.110 192.168.130.101 and 192.168.131.110 192.168.131.101 each of the other servers Discovery Portal have been pairs like this.

  iSCSI tab click on add 8 MPIO sessions at each of the ports on the MD3200i from Dell, target. For example, I added 1 session of 192.168.130.101 using it. Add Session,--> activate--> Advanced Mutlipath--> Local--> IP 192.168.130.110 initiator and target 192.168.131.101 iSCSI adapter. This is repeated on all servers. 4 connections for each NIC.

  The network is very slow. It revolved around 2 to 4 MB/MIN and it should be much faster. Initially, we had only the Cisco switch with only 1 VLAN and everything connected directly to it. I read somewhere that MPIO has been the problem, so I went through the same configuration but does not verify the MPIO checkbox above. Once this has been done, the network speed went up to 1.5 GB/Min but modular storage Dell was not happy, and virtual servers would fail and the connection is not very stable.

  What wrong with my setup? Can I directly home and fix the servers directly to the PowerVault and will make stable and allow for failover and redundancy NIC? I need to get this stable so I can move with something else.

  Thank you Ron

  You will need to change your system of intellectual property on this:

  rbramble

  EX-Node1 iSCSI-1 192.168.130.130

  EX-Node1 iSCSI-2 192.168.131.130

  EX-Node2 iSCSI-1 192.168.132.140

  EX-Node2 iSCSI-2 192.168.133.140

  Prod-Node1 iSCSI-1 192.168.130.10

  Prod-Node1 iSCSI-2 192.168.131.10

  Prod-Node2 iSCSI-1 192.168.132.20

  Prod-Node2 iSCSI-2 192.168.133.20

  Reference Dell MD3200i

  Controller 0 Port 0 - 192.168.130.101 Jumbo Frames 9K

  Controller 0 Port 1 - 192.168.131.101 Jumbo Frames 9K

  Controller 0 Port 2 - 192.168.132.101 Jumbo Frames 9K

  Controller 0 Port 3 - 192.168.133.101 Jumbo Frames 9K

  Controller 1 Port 0 - 192.168.130.102 Jumbo Frames 9K

  Controller Port 1 1 - 192.168.131.102 Jumbo Frames 9K

  Controller 1 Port 2 - 192.168.132.102 Jumbo Frames 9K

  Controller 1 Port 3 - 192.168.133.102 Jumbo Frames 9K

  Your iSCSI sessions will be:

  For EX-Node1:

  -192.168.130.130 to 192.168.130.101

  -192.168.130.130 to 192.168.130.102

  -192.168.131.130 to 192.168.131.101

  -192.168.131.130 to 192.168.131.102

  For EX-Node2:

  -192.168.132.140 to 192.168.132.101

  -192.168.132.140 to 192.168.132.102

  -192.168.133.140 to 192.168.133.101

  -192.168.133.140 to 192.168.133.102

  For Prod-Node1:

  -192.168.130.10 to 192.168.130.101

  -192.168.130.10 to 192.168.130.102

  -192.168.131.10 to 192.168.131.101

  -192.168.131.10 to 192.168.131.102

  For Prod-Node2:

  -192.168.132.20 to 192.168.132.101

  -192.168.132.20 to 192.168.132.102

  -192.168.133.20 to 192.168.133.101

  -192.168.133.20 to 192.168.133.102

• PERC H310 Mono Mini Non-RAID?

  Hello guys,.

  If anyone can confirm me a Perc H310 support (built-in) mono mini disc in Non RAID mode as noted above? (from http://www.dell.com/learn/us/en/04/campaigns/dell-raid-controllers#campaignTabs-1

  PERC H310 Mono Mini

  6 Gbps SAS

  PCI-Express 2.0

  2 x 4 internal

  -

  -

  0,1,5,10,50

  16, not RAID 32

  Hardware RAID

  I don't understand why I can't convert the non-raid drive in the BIOS of the controller or the idrac interface. There is no menu to do it in the bios, and while the menu appear in the interface of the idrac when I try to apply, it is said that the operation is not supported.

  Thx for the help.

  Sorry, everyone I just found the solution, 'Default' and now my records are in non-raid mode.

• R320 / Perc H310 / SATA 3.5 - want to use SSD

  Hello

  I recently bought a Dell taking r320.

  Unfortunately, I realized that I would have probably gone to Perc H310, am looking to upgrade. I would also like to run with SSDS supported, even if it is in the format of disk 3.5 "caddy. Can someone help me determine what parts I need to buy for this specification. I don't mind move from SATA to SAS (no doubt, it's just a change of cable?).

  Thanks for your help.

  Looking at your photos (which somehow only published this morning, but with a timestamp older than my response), you don't need to worry about wiring. Backplane SAS aura disks SAS or SATA, 2.5 "or 3.5" variety.

• Reference Dell MD1200, H710 with R720XD

  Hello

  Asked if drieves NL - Seagate SAS (ST4000NM0023) can be used in the following configuration.

  Reference Dell Perc H710 + PowerEdge R720XD MD1200.

  The answer that I gave them was who should be tested. Because in documentation it is stated that mark Dell hard disks should be used.

  I know that some controllers Perc will give a warning each time if not dell disks are used, but they work without problems. Is this the case even when you use a box MD1200?

  Kind regards

  Indrek

  INDRP,

  You're right that only some drives are tested and supported in the bays of the MD. Here is a link that will take you to one of the manuals that list all drives supported for 1200 MD and MD1220.

  FTP.Dell.com/.../PowerVault-md1200_Reference%20Guide_en-US.pdf

  Please let me know if you have other questions I would be happy to help.

• Reference Dell T310 - laboratory home

  Hi all

  I want to buy 2 of the Dell Poweredge T310 server for my laboratory at home to practice and prepare for my VCP certification. Here is the specification I chose and please let me know if this is compatible and I'm good to go set up my lab, I have to make changes to these specifications? I have not ordered any RAID controllers and do I really need?

  PowerEdge T310 chassis with up to 4 hard drives and Quad Pack LED Diagnostics
  Delivery charges for PowerEdge T310
  16 GB 1333 MHz UDIMM memory
  X 3430 Xeon processor, 2.4 GHz 8 MB Cache, Turbo
  PowerEdge T310 heatsink of heat
  No controller
  No operating system
  Gigabit network adapter double built-in
  Controller BMC
  Cable for optical drive SATA for PowerEdge T310
  Integrated SATA, 1-4 hard drives connected to the integrated SATA - no RAID controller

  250GB 7.2 k RPM Serial ATA 3Gbps 3, cable 5po hard drive

  250GB 7.2 k RPM Serial ATA 3Gbps 3, cable 5po hard drive
  Non-redondante 375W PSU

  Thanks in advance,

  I found the focus check tracking if help http://communities.vmware.com/message/1475041

  I am looking in HCL - check result.

  Research: Your search for "Systems" returned 2 results.
  Display:

  Name of the partner	Model	CPU series	Supported releases
  REFERENCE DELL	PowerEdge T310	Intel i3/i5 Clarkdale series	ESX 4.1 U1 4.1 4.1 U1 4.1 ...
  REFERENCE DELL	PowerEdge T310	Intel Xeon 34xx series Lynnfield	ESX 4.1 U1 4.1 4.1 U1

  ? deviceCategory = Server & productid = 10062 & releaseid = 142 & deviceCategory Server = & partner = 23 & keyword = t310 & page = 1 & display_interval = 10 & sortColumn = partner & sortOrder = Asc "> 4.1 ...

  Please, do not forget the points of call of the "useful" or "correct" answers

  Mauro Bonder - moderator

• Reference Dell 1700 crashed and I have no backup

  Reference Dell 1700 crashed without backup whats a girl to do
  
  

  lost all programs can run does not help

  Reference Dell 1700 crashed without backup whats a girl to do

  
  

  lost all programs can run does not help

  Reinstall Wndows.

  Reinstall all your programs from the original media or downloaded files you have saved on an external drive.

  Reinstall all your data from the backups that you made on an external drive.

  If you have not, you're out of luck.

• Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD

  Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.

  Hello

  1 have. what fixit you tried?
  2. don't you make changes to the computer before the show?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.