Refuse the selected inside address for internet access

Similar Questions

• When I connect my computer to the Netgear router, they do not seem to recognize the signal from the modem. I have to run each device directly to the modem (one at a time) for internet access.

  I have both a laptop and a desktop computer and use a modem wired high-speed internet.  I bought a router "Netgear" 5 port so that I could have both online at the same time, but when I connect my computer to the router, they do not seem to recognize the signal from the modem. I have to run each device directly to the modem (one at a time) for internet access. It gets very tedious, please help...

  Original title: router does not work...

  Hello

  Welcome to the Microsoft community.

  I see that when you connect multiple computers using the Netgear router, it does not recognize the signal from the modem.

  You must contact the ISP to verify if they can help you with this question.

  In addition you can keep these items handy, it might help you.

  Set up a wireless router

  http://Windows.Microsoft.com/en-in/Windows7/set-up-a-wireless-router

  Install or remove a modem

  http://Windows.Microsoft.com/en-in/Windows7/install-or-remove-a-modem

  Change modem settings

  http://Windows.Microsoft.com/en-in/Windows7/change-modem-settings

  It will be useful.

  If you need help with Windows, let know us and we will be happy to help you.

• Extend my extreme network with another extreme - waiting for internet access

  Hello - I have a new generation Airport Extreme (let's call it Extreme1) connected to a Comcast modem and it works very well. The extreme will be the router that the modem has no router function. I'm trying to expand my network to another room with another extreme (let's call it Extreme2). I have a connection cable between two rooms. Extreme1 has an ethernet cable from one of its LAN ports connected on port WAN Extreme2. When I try to create a new network with Extreme2 (in aid of the same name, passwords, etc.) it does not work. He was suspended at the end when he is looking for a connection ("Waiting for internet access")-I did the following things based on what I read here:

  1. Changed IPv6 link local parameters
  2. Tried the whole upward on my Macbook and tried on my iphone
  3. The Wan first and then tried to change the configuration after you done for Extreme2 by creating a network
  4. Tried to create a network with Extreme2 connected directly to the modem
  5. Extreme2 factory reset after every attepmt

  And nothing works. Kicker is, I also have a reasonably new airport express and the same thing happens to her as well.

  Do I need to adjust some parameters of network that I'm not aware of? Is it possible that my LAN ports are disabled on Extreme2? It is brand new.

  Thanks for any help.

  Have you used the Apple Setup Assistant?  If you did, it had notified you that the extreme second was being configured "add using Ethernet. The wizard will automatically configure the second airport with the appropriate settings for you.  All you have to do is enter a name of device for the second AirPort Extreme.

  Here I'm assuming that you reset the second extreme to parameters by default until you set it up again and that your second Extreme is the current version of the "tower" or that of previous versions "flat or square.

  The example below shows an AirPort Express as the device which is the extension of the network, but you will see the name of your network and AirPort Extreme on your configuration screen.

  Post back if you need some tips on using the "Wizard" for your configuration.

  

• problem with the yellow triangle without preventing Internet access

  problem with the yellow triangle without preventing Internet access.in across the network!
  all PC go to the internet through TMG and some computers work very well and most of the computers triangle shows yellow and always go online, but the connection it needs to slow down, I do everything from restarting all switches and install new TMG and always exist and place on another line to outside the firewall problem disappear?
  What can I do :(

  Hello
  I advise you to follow the link below for Tech Net where your social networking question will be answered by IT pros.
  You can post/search here
  hope this helps,
  B Eddie

• Cannot configure the static IP address for Cisco Touch 8 "

  Hi all

  I found that I can not configure the static IP address for Cisco Touch on TC7.0.1 / 7.0.2 with the procedure described below.

  1. upgrade a codec (e.g. SX20 TC6.3 or less) and a touch paired with the codec for TC7.0.2.

  2. after the upgrade, désapparier (with the help of désapparier Touch button) touch and it reboot.

  3. tap on "IP settings."

  4. Select "Manual IP allocation".

  5. Enter the IP address, subnet mask, default gateway, and then press "Save".

  Even though we have configured the static IP address with the above procedure, IP allocation remains 'Auto' (= DHCP) and the IP address, subnet mask, default gateway is also empty.

  In this situation, the only way to configure the IP address for the Touch is to use the DHCP server.

  I guess many users uses the static IP assignment like us, so please fix it as soon as POSSIBLE.

  Best regards

  Kotaro Hashimoto

  Hi Kotaro,

  It is a known problem in TC7.0.1 and TC7.0.2. The id of the bug is CSCum82147.

  To work around the problem, set IP address you want the button before moving on to TC7.0.x.

  The bug has been fixed and will be included in the next version of the TC software.

  Kind regards

  Jonas Tysso

• How to find the e-mail address for my HP 6700? Printer shows E-Print connected.

  I am using the Forum to get a new code to the printer and the printer shows homepage that's on, but now I don't know how to find the e-mail address for my computer.

  Hello

  In the front of the printer, go to configuration. Locate and enter the Web Services. Aprove any step to activate the service... leave the system a few minutes to complete your registration, a page will be printed automatically with the code printer and directions to select the email address of hpeprint.com.

  Kind regards.

• Where can I find the e-mail address for my printer HP 5520?

  Where can I find the e-mail address for my printer HP 5520?

  zubzub wrote:

  Where can I find the e-mail address for my printer HP 5520?

  Press the 'ePrint' on your printer - which will display your e-mail address of printer.

  If you have not enabled web services, you can do this from the settings button on the screen that appears on the printer screen when you press the ePrint.

• Hi, the creative cloud continues to send my inactive email account validation e-mail. How can I change the e-mail address for verification

  Hi, the creative cloud continues to send my inactive email account validation e-mail. How can I change the e-mail address for verification

  email https://forums.adobe.com/thread/1446019 or

  -http://helpx.adobe.com/x-productkb/global/didn-t-receive-expected-email.html

• Networking - can not access the Internet since I refused the offer of renewal for the Windows Live OneCare safety

  It seems that since I refused the offer of renewal of Windows Live OneCare security - which costs $50.00 per year - but is FREE via my ISP no longer, I can access Internet Explorer or is applications such as my printer, sounds etc... I called the mfg and they want $100.00! Seems that the warranty is sold out, as well!  Is there someone who can help free of charge until I get MORE money for MS?  I contacted my ISP & everything works well on their end, it's a problem of network management - they showed me how to run in safe mode to fix this problem.  Hope it works & thank you for the help!

  http://OneCare.live.com/standard/EN-AU/default.htm

  It is an abandoned product.

  http://social.Microsoft.com/forums/en-us/category/windowsliveonecare/

  I have suggesty repost you in the Forums above Windows Live OneCare.

  See you soon.

  Mick Murphy - Microsoft partner

• iPad will not bring the keyboard when I try to complete an external application for internet access

  Hello

  I have a new iPad 2 Air, and very recently he began to refuse to show the keyboard properly, when I am trying to log on to an external internet account. I am traveling and need access to the internet but cannot fill all the required fields, it will bring up the top gray bar with the top and down arrow (they don't do anything, I tried pressing all there) but nothing else, just white space below.

  I have read other blogs and tried to reset the keyboard and things like that but he even let won´t let the keyboard.

  So, I can not get Internet access Login. Please help, I m new to the forum and hope I've filled it out properly... apologies if I've made mistakes here.

  Sorry I haven´t understood my operating system, but when I try to check by going to the software update, it won´t not let me because I Don t have internet.

  I suspect a lot of these errors occurred when I updated to version 9.1 of the software as it is not the only problem I encounter now, however, at this stage, it is the most frustrating.

  Thanks in advance to anyone who can help me.

  Hello Cara, there.

  It looks like that your keyboard is not appearing when it should. I'd leave the applications that are run in which you try to get the keyboard works as well as the application of the parameters:

  Force an app to close the iOS
  https://support.Apple.com/en-us/HT201330

  1. press the Home button twice quickly. You will see small glimpses of your applications recently used.
  2. slide to the left to find the application you want to close.
  3. push upward on the overview of the application to close.

  When you have done that reboot the device and test again the question:

  iOS: switch off and on (restart) and reset
  http://support.Apple.com/en-us/HT201559

  I think that these apps may simply need to be reset and refreshed. Thank you for using communities of Apple Support, let us know how it goes!

• AnyConnect works at the main location and for internet, but not over the WAN

  I have a firewall of 5525 asa running an Anyconnect VPN.  I have three sites and it will be the access point for all.  There is a mpls wan between sites.  The Anyconnect IP pool is 192.168.165.x 255.255.255.0. In the primary site, the local IP addresses are 172.17.x.x 255.255.0.0 and 255.255.255.0 192.168.10.x legacy.  Remote sites are 192.168.20.x 255.255.255.0 and 192.168.30.x 255.255.255.0.

  From a PC to my LAN, I can reach the four lines and servers ping, tracert, and access by name or number.  When it is connected to the the anyconnect, I can only access the 172.17.x.x and 192.168.10.x.  We're set up for a lot of tunnel the VPN so this is important.  I tried to add routes to the routers on each side of the WAN to point 192.168.165.x traffic to the firewall's inside address based on a tip I read on the map here, but that did not help.  Any ideas where I should look next?

  Thanks for your help,

  Brad

  Cant it ASA itself remote peripheral ping at all sites?

  You have the NAT rules in place for example all traffic to the VPN range?

• Enable the VLAN on sub interface internet access but block traffic to VLAN native

  I have a 2821 router w / MLS 2024 switches.  Native VLAN(default vlan) is my private network and VLAN 100 is my comments system.  Below is my interface config...

  interface GigabitEthernet0/1

  Description ES_LAN, ETH - LAN$ $$

  IP 10.1.0.2 255.255.0.0

  penetration of the IP stream

  IP nat inside

  IP virtual-reassembly

  automatic duplex

  automatic speed

  !

  !

  interface GigabitEthernet0/1.1

  encapsulation dot1Q 100

  IP 10.3.1.254 255.255.255.0

  penetration of the IP stream

  IP nat inside

  IP virtual-reassembly

  !

  IP default-gateway xx.xxx.xxx.xxx

  IP forward-Protocol ND

  IP http server

  23 class IP http access

  local IP http authentication

  IP http secure server

  IP http timeout policy slowed down 60 life 86400 request 10000

  Default route is defined...

  IP route 0.0.0.0 0.0.0.0 xx.xxx.xxx.xxx

  Access list are...

  access-list 175 deny ip 10.1.0.0 0.0.255.255 10.2.0.0 0.0.255.255

  access-list 175 allow ip 10.1.0.0 0.0.255.255 everything

  access-list 175 deny ip 10.3.1.0 0.0.0.255 10.1.0.0 0.0.255.255

  access-list 175 allow ip 10.3.1.0 0.0.0.255 any

  I want to continue to have access to the guest VLAN in VLAN private to allow the management of points of access etc.

  I want to allow internet access as guest newtork but block it to access my private network.

  Don't know how to do in this regard.  I tried to change the ACLs (remove the 10.3.1.0 entries) and creating an another acl for the Scriptures and applying that VLAN 100 sub interface... so far without success.

  Thanks in advance for the help!

  Hello Chris,

  > From this point of view should I leave the above lines and create another list acl for the 10.3.1.0 of the network and apply entering gig0/1.1?

  I would go this way, as in a simple ACL, you can't express your needs. The ACL to apply on gi0/1.1 will probably need further instructions then the ones I suggested, but divide the problem into smaller manageable pieces is a good strategy.

  > Also with this config would be NAT be performed on each network by making this change?

  Until the internal network and network of comments are on the same side (ip nat inside) there is no NAT triggered in communication between them so that you should not influence the NAT configuration with this change.

  Hope to help

  Giuseppe

• The remote VPN Clients and Internet access

  I apologize in advance if this question has already been addressed. I am currently using a PIX Firewall Version 6.1 520 (2) running. I have several remote users that VPN for the PIX. Once the VPN tunnel is started, they are more able to connect to internet from their local computers. Is there a configuation on the PIX that allows remote users to have access to the internet when you are connected to the PIX.

  TIA,

  Jeff Gulick

  The Pix does not allow traffic enter and exit on the same interface. Therefore, a VPN user cannot access the Internet through the tunnel. If you use the Cisco client, enable tunneling split so that all traffic through the tunnel.

  If you use PPTP, you can turn off the option that makes the remote network, the default gateway. However, local routes should be added to these clients when they connect.

  Or you can use an additional interface on the firewall. One that puts an end to VPN tunnels and another providing for Internet connectivity. In this way the traffic is not enter/leave on the same interface.

  Of course, it is preferable if the customer Internet traffic does not go through the tunnel. It wastes your bandwidth and has security problems as well. I suggest you use the client to Cisco and the split tunneling.

• How can I identify the program that turns my internet access?

  Normal mode startup I get an IP address from my router but no internet access, cannot ping the router IP address or IP address of another computer on the local network.  I ping my own IP address.  I can access the internet if I start my computer in Safe Boot w/Internet.  I'm guessing that a program is power off or blocking the ability of network cards to talk beyond my computer during startup.  There are system variables, I can look at, or a list of programs that need to run, so that I can turn off others and test to see if the network works? This problem affects both my Wi-wired connections and my computer.  They both Act the same way.  I even installed a second adapter USB wireless as a test and it also reaches the router initially and then won't talk to her after the security negotiation.  McAffee software detects no virus on the system and no virus found or deleted in the previous analysis of the reports.  The problems started when I rebooted my machine to get the sound to work.   I had been running without the speakers connected and found the sound does not when I plugged.   The only known software update was of Flash Player, but I see no way out with a restore point, which is days of May and was generated from a Windows Update.  Everything worked fine after that Windows Update including the speakers.   I need help, or will be forced to recreate the image on my machine, I want to avoid.

  McAfee has been updated at the same time as the last batch of updates from Windows 7 and this is the cause of problems of internet connection for most, if not all, users of McAfee.

  See the communication from this "criticism" - McAfee

  Some customers may experience a loss of network connectivity and/or errors in McAfee Security Center after a recent update

  You should make the fix McAfee, if necessary. There are corresponding communications for their enterprise products.

  I had to run the removal of McAfee Development tool a few times before and it caused a problem with the license if the PC was not connected to the internet during the abduction. Due cat of McAfee support reset their files in order to allow the relocation-reactivation. Here is their link cat - McAfee - media contains the link to the cat

• Internal untrusted clients directed to the external IP address for traffic PCoIP

  I have a network segment disable my firewall for some untrusted clients. When untrusted clients connect to view (5.3), they use a DNS name that resolves to a DMZ (view Security Server) host. That's where I think the problem is: it seems that security server responds with its external IP address, and then all the PCoIP traffic is routed to my router (where the external IP address can be found), then back into view and the customer. Traffic of SSL connection works fine, the traffic remains inside and does not get directed to the external IP address. It is only the PCoIP traffic that gets invited to use the external IP address.

  It seems that DNS is not enough - Security Server seems to respond and connect using only the external IP address configured in the external URL field PCoIP - is this correct? If so, then to do a substitution for the external URL so that internal untrusted traffic doesn't get routed the external IP address - this creates a lot of unnecessary traffic, mess with QoS, etc..

  Another idea would be to allow untrusted clients to connect directly to a login server instead of sending them on the Security Server, but I don't think that it is a best practice...?

  Mike

  As Linjo says the simplest solution is to set up a server for additional security to point these clients (no need of another server connection, you can pair it with the existing one). Today, you are required to provide an IP address for PSG, so if you need to send it to another, you will need a second server.

  Of course, if they are completely not reliable customers, then you can force through the external access point still but looks like you need avoid the cost of additional traffic from this approach.

  Mike