Regain access after the plant recover?

Similar Questions

• No Internet access after the connection of the cisco vpn client

  Hi Experts,

  Please check below config.the problem is vpn is connected but no internet access

  on the computer after the vpn connection

  ASA Version 8.0 (2)
  !
  ciscoasa hostname
  activate 8Ry2YjIyt7RRXU24 encrypted password
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  IP 192.168.10.10 255.255.255.0
  !
  interface Ethernet0/1
  nameif inside
  security-level 100
  IP 192.168.14.12 255.255.255.0
  !
  interface Ethernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  2KFQnbNIdI.2KYOU encrypted passwd
  passive FTP mode
  standard access list dubai_splitTunnelAcl allow 192.168.14.0 255.255.255.0
  INSIDE_nat0_outbound list of allowed ip extended access all 192.168.14.240 255.255.2
  55.240
  pager lines 24
  Within 1500 MTU
  Outside 1500 MTU
  IP local pool testpool 192.168.14.240 - 192.168.14.250
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access INSIDE_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 192.168.10.12 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout, uauth 0:05:00 absolute
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.14.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-md5-hmac setFirstSet
  Crypto-map dynamic dyn1 1 set transform-set setFirstSet
  Crypto-map dynamic dyn1 1jeu reverse-road
  dynamic mymap 1 dyn1 ipsec-isakmp crypto map
  mymap outside crypto map interface
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 43200
  crypto ISAKMP policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  a basic threat threat detection
  Statistics-list of access threat detection
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  !
  global service-policy global_policy
  password encrypted user testuser IqY6lTColo8VIF24 name
  username password khans X5bLOVudYKsK1JS / encrypted privilege 15
  tunnel-group mphone type remote access
  tunnel-group mphone General attributes
  address testpool pool
  tunnel-group ipsec-attributes mphone
  pre-shared-key *.
  context of prompt hostname
  Cryptochecksum:059363cdf78583da4e3324e8dfcefbf0
  : end
  ciscoasa #.

  Hello

  Large.  Try adding the below to make it work

  vpn-sheep access list extended permits all ip 192.168.15.0 255.255.255.0

  NAT (inside) 0-list of access vpn-sheep

  Harish

• Need help to try the Windows 7 network computers after the plant level and fresh

  I'm having a bad time trying to network Windows 7 computers after a few updates and install fresh is someone as trouble with windows 7? homegroup? IsUP WTF? Tried x

  Hi Bert Primus,

  Welcome to the Microsoft community forums!

  If I understand correctly, you need assistance in networking to Windows 7 computers after the upgrade. I've surely you will help find a solution on the issue.

  1. how many computers trying to network with each other?

  2. what happens when you try to connect to the computer as a whole?

  3. do you get an error message?

  Method 1:

  If you set up a home network in Windows 7, see the article:

  Start here to set up a home network in Windows 7

  http://Windows.Microsoft.com/is-is/Windows7/start-here-to-set-up-a-home-network-in-Windows-7

  See also:

  
  Networking
  http://Windows.Microsoft.com/en-in/Windows7/products/features/networking

  Networking of computers running different versions of Windows

  http://Windows.Microsoft.com/en-in/Windows7/networking-home-computers-running-different-versions-of-Windows

  Method 2:

  To learn more about homegroup in Windows 7, check out the links below:

  What is a homegroup?
  http://Windows.Microsoft.com/is-is/Windows7/what-is-a-HomeGroup

  
  Homegroup from start to finish

  http://Windows.Microsoft.com/en-in/Windows/HomeGroup-help#HomeGroup-start-to-finish=Windows-7&V1H=win8tab1&V2H=win7tab1

  Home Sweet homegroup
  http://Windows.Microsoft.com/is-is/Windows7/help/home-sweet-HomeGroup-networking-the-easy-way

  Provide more information about the issue so that we can help you. Hope this information helps.

• Vista wireless loses Internet access after the mode "Eve".

  Environment:
  HP Pavilion dv2610ca notebook PC, broadcom 802. 11 b / g adapter, Vista Home Premium 32 bit SP2, Siemens Gigaset SE567 router/modem.

  Problem:
  I can usually connect wirelessly to my home network and to the Internet whenever I start my computer. However, I have close the lid and leave it in standby mode, I can't access Internet after I opened the lid and the system wakes up. The system connects to my home network but cannot access the Internet. It shows a Local access only.

  Diagnosis and repair fails generally, telling me that I have a problem with my router. Disconnect, then reconnect usually works. My router power market also works.

  I saw lots and lots of issues with Vista wireless networks and I followed several of the recommended actions:
  -updated the driver broadcom
  -reset the IP stack by using the tool "Fixit" of Microsoft
  -disabled the use of IPv6 in two by disabling the check marks in the related devices and changing the registry TCPIP6 parameters
  -modified the registry to activate/disable the DHCP broadcast flag in the TCPIP Interfaces
  -J' tell the system not to disable the card Broadcom, but the "Power management" tab mentioned in some articles does not appear in its properties. The only reference to power is "Minimum energy" under the "Advanced" tab, then I disabled who.

  Nothing has solved the problem.

  Has anyone else had this problem and fixed it?

  I'm not a technical Wizard, so please provide instructions for any action that you suggest.

  Thank you.

  I replaced the Siemens router/modem provided by my ISP (Telus) with an old D-Link router and separate modem 3Comm I had been using a couple of years and the problem seems to have disappeared.

  I'll close this thread on the assumption that the problem will not rear its ugly head again.

• No Internet access after the update from Windows 7

  Since the update of Windows 7 (from my list of update I can not single out one specific) sent 15 Dec - my computer will access my internet connection - the only way that I can access is to do a system restore to a point to Dec. 14 or before - I have a new computer - and no new programs have been added to the system during this time - it becomes troublesom because I have to constantly to do system restore to get online

  I called Support Center, Monday - and after having him work for almost 2 hours, we decided that the KB2467659 update is the culprit and we have disabled this update to be installed - HOWEVER the windows update program was H - LL BENT on installing this update - the technician called me back 2 days later Wednesday--and we did other things magic to ensure that this implementation to day has NOT been installed again - so far (knock wood) No recurrences of the problems

• Tecra A11 - 1EG - cannot be accessed after the supervisor setting BIOS password

  Hello, I would like to know if anyone can help?

  We have started to put a supervisor on our laptop Tecra A11 password so that our students can not set passwords on the hard drive, etc.

  To enter the BIOS and set a BIOS password, press us F2 that the machine starts.
  Then we go to the security option, then supervisor password.
  After entering the password we use twice, press us F10 to save etc.

  The machine starts ok and will windows smoothly.

  The problem we have now, is that we cannot go back into the bios at all.
  As machine starts support us on the "F2" key as before, but unlike previously the screen remains white and the "Toshiba leading Innovation > ' screen no longer appears."

  If we keep our finger on the F' key or continue pressing the laptop restarts just without ever get to the BIOS screen where I guess that get us ask the supervisor password that we set earlier?

  Is there another key, that we should be pressing that start the laptop?

  I would add that we have added a password of supervisor for the screen of security BIOS on three of our laptops and all three have the same problem.

  Thank you

  Steve

  I think this should be useful for you:
  http://APS2.toshiba-tro.de/KB0/TSB0B032D0000R01.htm

  In some cases, you need to press the "INS" in Toshiba logo appears.

  Then appears a prompt for the password for the supervisor and if the password is certified then the BIOS could be entered by pressing the "F2" key

• lost internet access after the connection to the server

  Have had this problem in the past and in the hope that a workaround is available.

  MAC OS X El Capitan worm 10.11.2 runs and loses the Internet when connected to a server/sharedrive(on Microsoft Windows environment).

  You asked the same thing, or a similar, issue in October 2014. What happened after that?

• ReadyNAS Pro 2 - Can't access after the factory reset/install

  Hey all,.

  Have a Pro 2, which responds more recently. I can factory reset it and start the installation process in RAIDar. But when he sets up the discs that it disappears in RAIDar and I can't access the web interface (responds to the pings, however).

  Problem of firmware or RAM?

  You came across a problem that we see in some cases, when do a factory reset. It should now be fixed.

• Unauthorized access, after the trial expires

  I got the trial of DPS, it is now expired, so I see access not allowed - you have no permission message, etc. I tried several times to contact Adobe by various means - no response - no surprises! I'm a DPS Certified Adobe instructor, I need to see the/train customer perspective in what is happing in the world of Adobe DPS - I can't, but I can say for them, it's that there are great alternatives out there, Twixl, Aquafadas, In5 Mag +, etc. These people will talk to you, they will be transparent about everything, including costs. I agree that DPS 2015 should be only price wise for a certain segment of the market and Adobe apparently now have no interest in the market of the other segments, but come on Adobe - talk to us and let us at least power free trial/test/train your product.

  
  

  In the words of Pink Floyd "Is there anybody out there?

  Hello Peter,.

  You can contact me at ktukker (a) adobe.com? Please provide the information that you used to register for the 30 day trial.

  The 30 day trial is available to freely test the product. On request, the trial can be extended to 60 or 90 days on request in order to allow more time evaluation.

  With sincere friendships.

  KlaasJan Tukker

  Adobe

• Am unable to regain access to the two versions of Photoshop and Illustrator CC cc 2014

  Hello, I recently downloaded the 30 days of testing by 2015 illustrator and photoshop programs. After that, I realized that I was unable to create files that would be able to be consulted on the programs of 2014. Upon learning this, I quickly uninstalled programs. InDesign CC 2014 remains available for use, therefore, YES, I'm still paying for it. I am unable to find the versions of PS 2014 and have... Even when I search the creative application of cloud. Any suggestions? I'm in College and need these programs and am already paying for them, but I can't re - download.

  Thank you

  Hello

  Please see the link below to return to the CC2014 apps:

  How to find and install a previous Version of Adobe Apps in CC 2015 | Adobe Customer Care Team

  
  

  Kind regards

  Sheena

• JDeveloper 11 g - value of bean to access after the method call.

  Hello
  
  I created a command button to run a PL/SQL method, as shown in the example call: http://download.oracle.com/docs/cd/E17904_01/web.1111/b31974/bcadvgen.htm#BABEIFAI 37-11
  
  I have the following code, to fill a java bean in my ApplImpl class.
  
  Result APIResultBean = new APIResultBean();
  // 7. DateValue property value using in-first OUT param
  result.setResultValue (st.getString (28));
  // 8. StringValue property value using THE param 2nd
  result.setMsgValue (st.getString (29));
  System.out.println ("Bean defined:" + st.getString (28) + "and:" + st.getString (29));
  
  The java bean has the following code and is defined as a java class in my model of controller:
  
  package CELPAY.model;
  
  import java.io.Serializable;
  Import oracle.jbo.domain.Date;
  
  / public class APIResultBean implements Serializable {}
  
  
  
  String ResultVal;
  String MsgVal;
  
  public setResultValue (String ResultVal) Sub {this. ResultVal = ResultVal ;}
  public String getResultValue() {return ResultVal ;}
  public setMsgValue (String MsgVal) Sub {this. MsgVal = MsgVal ;}
  public String getMsgValue() {return MsgVal ;}
  
  }
  
  
  
  The procedure runs, but I have no idea how to do to retrieve the output variables in a form as a text of output. That is to say, how can I access this bean? I tried to create a data control, but the methods come not through. I also tried this entry in the adfc. - config.xml and refercing variables.
  
  My question is tha that the getResultValue methods are not displayed in Jdevloper?
  
  Great satisfaction to all helped, because I was stuck on this all day

  Your Get accessor method is getMsgValue(), the rule says remove the GET and change case of the first character of the remaining string. If getMsgValue()-> MsgVale-> msgValue.
  Try #{bindings.element.inputValue.msgValue}

  Timo

• Satellite A100-386: no internet access after the new XP installation

  Hi everyvody!

  I can do it myself, so I ask for your help!

  I have a Toshiba Satellite A100-386 with windows XP MCE.

  I recently had a virus, so I formatted my drive. I don't have the installation CD with me, so I install XP.
  I have two disc on my computer with the system and the other with the documents.
  Then I install ALL the drivers I could find on the Toshiba site for my computer.
  This means that the PSAA9E. The problem is that I have no internet! I don't understand why.

  When I look in computer management, I have no ethernet, controller mass storage controller and network controller.
  I have zone alarm as a firewall and an antivirus avast!

  I disabled avast to be sure that he's not in it but no result...
  In Thoshiba drivers there is also something to update the BIOS.
  I did it but I didn't change. I hope the problem here not there...

  It will be really nice to help me ^^

  Hello

  I think that you just have not installed the right driver LAN and WLan driver

  As much as I know this laptop supports Intel Pro 100 Lan and WiFi Intel 3945ABG card card

  Please visit the European driver Toshiba page again and download the compatible network driver and the driver WLan.
  Unpack the packages, then install it.

  Finally check again if the LAN and WLan cards were recognized in the Device Manager in network adapters.

  Good bye

• After the Bios Update get persistent "reboot required" screen, impossible access tune

  Hello

  I just updated the Bios F.23 to F.36 as recommended by the HP Wizard for a laptop of HP Envy m7-J010DX, Win8.1.

  However, I now get the persistent "reboot required" screen whenever I try to start the HP Wizard. I tried to reboot several times to nothing does not.

  I had this problem before, but I was able to access the HP Wizard at this time (I don't know why the problem eventually disappeared, possibly one of several updates).

  I would like advice on how to solve this problem and regain access to the HP Wizard.

  Thank you.

  Do you mean to say HP Support Assistant, instead of tune?

  Uninstall the version you have and that you install the latest version from the download section of your laptop Support Portal.

  are you mobile operating system Windows 8 or 8.1 Windows computer?

  Always include this information when posting. We can see through the inernet and know what is installed. My ESP is now broken.

• How can I regain access MyWindowsApp administrator account on Vista?

  I changed my password last summer and actually I FORGOT my new password. I have locked my account administrator, but have been able to access through the guest account settings. I didn't know that Vista required to create a password reset disk before I changed the password. How can I regain access to the administrator account without having the password reset disk?

  Hello

  I think you left it too late in what concerns the use of the password for the original as requiring the use of a system restore point which, after this time may not yet exist

  but you can try it

  If this does not work, you will need to reinstall vista

  This is the information from microsoft on you assist on passwords

  http://support.Microsoft.com/kb/940765

  except that we cannot help you

  read this microsoft's policy NOT to provide assistance to crack passwords:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/keeping-passwords-secure-Microsoft-policy-on/a5839e41-b80e-48c9-9d46-414bc8a8d9d4

• Internet host stops working after the launch of Workstation 7.1

  I recently downloaded the installation program VMWorkstation 7.1 (about 570 MB) on the VMWare site.  I tried to install on a Windows XP host that currently has VMWorkstation V6.x and he complained the old version.  I tried to uninstall the old version, but which failed to remove the product from the hard disk and the registry, but it was removed from the ARP.

  The VMWorkstation 7.1 installer still does not have due to the old version being present.

  So, I manually rename the registry key of VMWare and installation folder.  This allowed the 7.1 version to install, but now I see a strange behavior.  When I start a Windows 7 Profession VM, the VM guest starts very well, but the host system loses the internet.  Even after having turned it off VM Workstation, the host system can no longer access the internet.  But it can still access files on our local network servers.  I need to reboot the host system to regain access to the internet.

  Any ideas on what could cause this problem?  Would be additional steps must be taken to completely clean out the older version from the host system?

  Thank you

  Shawn

  Please take a look at http://kb.vmware.com/kb/1308 which explains how do to clean the system fails.

  André