Removal of VLAN Tag on SG300.

Similar Questions

• SG300/SG500 remove interface vlan

  Hello!

  The question is the following:

  I add a VLAN interface to test IP connectivity to this vlan by adding an IP address for this interface vlan and ping on a host.

  for example
  interface vlan 5
  192.168.0.251 IP address 255.255.255.0

  Then I can remove the ip address "without ip address', but I can't delete the ' interface vlan 5".»

  Even when I delete the vlan itself of the database for vlan. There is no command "no interface vlan. I can only stop the interface vlan.

  If anyone knows how to remove the interface vlan switches SG300/SG500 cli.

  Thanks, Woeger

  Hello

  I tried just that with my switch from laboratory here.

  I created VLAN 10 and he has given an IP address.

  Then I did a no ip address on the interface VLAN and then not a vlan 10.

  At this stage there is no interface THAT VLAN 10 in my config running or when I do a show ip interface.

  So remove the VLAN has done actually remove the interface for me, brings me to my question.

  What version of the bootcode/firmware do you currently use?  Maybe this problem has been fixed, because I am running 1.3.7.18 firmware with 1.3.7.01 code to boot.

  If you are on a low moving forward and put to date, don't forget to upgrade the boot thus code, it is necessary for new versions of firmware.

  Hope that help, but if not just let me know and we can take another look,

  Christopher Ebert - Advanced Network Support Engineer

  Cisco Small Business Support Center

  * Please note the useful messages *.

• VLAN: ESXi <>- Cisco SG300

  Hey everybody,

  I always try to get the hang of networking with ESXi/vSphere...and I was little confused as I had a configuration problem.

  I have an Intel NUC5i5MYHE with 5.5 ESXi. As he has that one NETWORK card I am configuring a trunk so I can separate groups of ports within the host with the VLAN.

  Cisco SG300 has several VLANs (including: HAND = 10, LAB1 = 20, LAB2 = 30). * 1 is still active but VLAN native = 999 *.

  MAIN are all fair access Ports on VLAN10 (10UP).

  GE22 is a trunk with VLAN 10, 20 and 30 with label (10T, 20T, 30t, 999UP).

  A few groups of host ports ESXi has currently (simply called the VLAN I want installation and set on the VLANs)

  Also, I created the extra VMkernel port with VLAN10 just for wasting his time with (I can't access to this IP address, but after looking at VMK0, I think that I need to add static routes to the bridge?)

  V0 & VMkernel 0 = VLAN 0 (none)

  V10 & VMkernel 1 = VLAN 10

  V20 = VLAN 20

  So, with this configuration, I am unable to access the host via vSphere Client. However, if I put GE22 on SG300 to 10UP (10UP, 20T, 30t) I AM able to access... but is not what I want, right?

  To my knowledge... 0 (none) passes a VLAN while 4095 (all) does not take into account any VLAN tags completely, sending the frame as-is to the customers. (While I would let VMK0 0 (zero) as the correlates directly to my unique NIC physical, right?)

  So... my computer that connects with the vSphere Client Gets VLAN10 penetration tag (access). Switch then forwards Egress GE22 through the trunk to the ESXi host with a labeled VLAN10 framework.

  The framework should be accepted at the VMK0 whatever the tag VLAN and connect or if the frame belonged to another customer sent on the vSwitch... unless I'm confused here somewhere.

  Can someone enlighten me please?

  Thank you

  Basically, you have two options. If native/default of the physical switch port VLAN is set on the Management VLAN, then do not set a VLAN ID on the management VMkernel port group, otherwise the value the VLAN ID on the virtual side. Ultimately that a single point (the physical switch port, or the virtual port group) is responsible for the labelling/close the network frames.

  André

• How to remove a "people tag" in the Windows Live Photo Gallery?

  How to remove a "people tag" in the Windows Live Photo Gallery?  The
  has been named wrongly face and I don't understand how to remove.

  Hi pinecamp1972,

  We recommend that you ask your question in the forums photo gallery for better assistance.
  See Windows Live Photo Gallery Help Center

  Visit our Microsoft answers feedback Forum and let us know what you think.

• PowerConnect 5448, how all the trunk of physical ports and allow all the VLAN tags to pass transparently

  I would like to achieve such a goal, do all acts of switch ports 5448 as 'trunk', that is, just as an entry-level switch. Yes, I want all the tags VLAN through seamlessly.

  Let me explain more clearly. If

  • With MAC1 PC1 is connected to switch port 1 (port 1) in short, PC2 with MAC2 is connected to port 2.
  • PC1 sends a packet with vlanid = 30 ethernet VLAN tag,.

  I want the ethernet packet must be SENT to port 2 without modification, i.e. 2 PC will receive the package with exactly the same byte packets that PC1 sends.

  Currently, I want to configure all ports from the switch to act like this, but how to do this? Can someone tell me the more concise CLI commands to achieve? Alternatively, it is possible via the web interface?

  I must again complain the poor manual, which talks about this concept and this notion over and over again (both of ambiguous statements that the author of manual does not), BUT doesn't explain them not at the level of the content of the packages, so I'm totally at a loss.

  I tried the web interface. Simply together port 1 and 2 for access mode or general mode does not work.

  Please help me. Thank you in advance.

  Thank you, Josh, you begin to point me in the right direction.

  Now, I know just affecting a Trunk port, or general mode is NOT sufficient.  I have to give what kind of package VLAN (i.e. what VLAN ID) are allowed to pass through.

  To do this assignment, I have to take 2 steps. say first of all, the database "vlan" to recognize a VLAN ID in the world, then say that some specific port is allowed to pass through with this VLAN ID specific packages.

  Thus, in order to pass packets VLAN with VLAN ID 18-25 no modified (marked packets in packages marked on) g7 to the g8 to port port, I have to do:

  Console # config
  Console (config) # vlan database
  Console(config-VLAN) # vlan 18-25
  Console(config-VLAN) # exit

  Console (config) # interface ethernet g7
  Console # switchport general mode
  Console # switchport General allowed vlan add the tag of 18-25

  and again for the g8. And if I want to 48 ports to act like that, I have to write this kind of order 48 times right? All the shortcuts?

  Some useful links for me: http://hasanmansur.com/2012/10/14/powerconnect-switchport-modes/

• RV Support VLAN Tagging on WAN Port?

  Hello

  I would like to know if RV Series Router can support VLAN tagging on the port WAN himself? I need this cause my ISP using these methods to connect to the router/modem to the end user.

  Thank you.

  -----

  Kind regards

  Danny

  Please visit RV315W.

• VLAN tagging on VIC 1225

  Hi community

  We are currently developing a standalone Server, installed c240 with a vic1225 (connected to a pair of vpc 5500 nexus).

  We have bare metal windows 2008 R2 os installed and active nic teaming ((802.3ad) with the enictool.)

  Now we want to Setup vlan tag NICs in windows, but there is no way to do...

  This is usually possible in windows 2008 Server?

  THX in advance for advice.

  Hello

  ENIC pilot for W2K8 does not support feature of 1 q VLAN dot.

  With W2K12, the grouping of the characteristic marking windows native driver.

  Alternative options are

  (1) implement adapter FEX

  (2) If you plan to run Hyper-V on the host, it can mark the VLAN.

  (3) implement individual vNIC for each VIRTUAL LAN and configure the host of active transmission load balancing / active. In addition, configure links on the individual switch ports allowing to the VLAN needed and have them not as a port-channel / vPC

  I recommend you to upgrade the firmware and drivers to the latest version to eliminate known issues.

  Padma

• BlackBerry smartphones remove the bilingual "tag.

  How can I remove the bilingual 'tag' that appears at the bottom of every email that I send? Thank you!

  Here you go:

  Thank you

  Bifocals

  http://bis.na.BlackBerry.com/HTML?brand=Bell

• Remove the video tags?

  I downloaded a few vintage movies - some have video tags, that some do not

  I order them all by using the file name
  WMP12 ordered them to Tag the video (if they have one) or name of file if they are not
  Tried to delete the video tags that I thought was a success, but they reappear whenever I reset the wmp database, reinstall windows, or access it from another PC = its not to delete the actual file tags, only from the WMP database
  Anyone know how to remove the video tags perminently
  Even better if I can delete them "mass"

  No, tags are stored in the file itself.  WMP can change its local database, but you will lose those changes whenever you reset (so do not reset there is a response).  But to strip out of the file itself, you'll need a program that can edit videos.

• VLAN Tagging (VST) and VLAN native on the same vswitch

  I'm trying to figure out if its possible to put running the VLAN tagging for a vswitch if our virtual machines are currently in the vlan 1 (vlan native) on our cisco switches. I don't know why it's set up this way, but change is not an option at this time.

  Ultimately what I'm trying to accomplish is setting up a group of servers that differ on one VLAN, but under the same vswitch. I'm assuming that VST is what I need, but I don't know if I can simply specify how vlan 1 as the vlan 1 is not marked on cisco switches and my understanding is that VST requires to carry a label.

  Your help is greatly appreciated.

  NuRD.

  With the vSwitch connected to a trunk on the physical switch port, create the port groups and you need only configure the ID then VLAN for the port groups that do not use of VLAN native. See for example http://kb.vmware.com/kb/1004074

  André

• Remove a conditional tag my content

  Using robohelp 10 on win 7

  I have 5 conditional tags in my HR project. In some cases, the text can be tagged with multiple conditional tags.

  I want to delete a batch tag content so that all content no longer uses this tag.

  Simply remove the tag from the pod of conditional compilation?

  If this is not the case, how can I do?

  Simply press the DELETE key and HR will tell you that it will remove the content tag. From my experience, it does. Test it in a fictional project in case of doubt.

  Also something like this, if not sure, back first.

  See www.grainge.org for creating tips and RoboHelp

  

  @petergrainge

• Several Vlan tagging to vswitch

  Hi I have abt 20 vm in an ESX 4.0 each with different vlan and all the virtual machine cannot see each other what would be a better approach for this configuration. create a virtual switch for each computer virtual but with different vlan tagging assign each? (virtual switch 20 sense) or use pvlan a better option for this I only got 2 physical cables connected to this esx carrying all the traffic 20 vlan. Or any other recommendation?

  Thanks for any info

  sounds odd humm maybe these articles can help you:

  http://communities.VMware.com/docs/doc-4861

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1004887

  Alex

• VLAN tagging without trade?

  Is it possible to VLAN tag a port vSwitch without using a GROUP of ports using PowerCLI?  Similar to how would tag a port on a physical switch.

  OK, you use dvSwitches!

  I understand now what you want to achieve, even if with the help of exchanges has more advantages then the VLAN ID only.

  Of course, that this can be accomplished by using PowerCLI too.

  Try something like this:

  $dvSwitchName = "dvSwitch0"
  $dvPortId = "100"
  $VLAN = 220
  
  $portSpec = New-Object VMware.Vim.DVPortConfigSpec
  $portSpec.operation = "edit"
  $portSpec.key = $dvPortId
  $portSpec.setting = New-Object VMware.Vim.VMwareDVSPortSetting
  $portSpec.setting.vlan = New-Object VMware.Vim.VmwareDistributedVirtualSwitchVlanIdSpec
  $portSpec.setting.vlan.inherited = $false
  $portSpec.setting.vlan.vlanId = $VLAN
  
  $dvSwitch = Get-View -ViewType 'VmwareDistributedVirtualSwitch' -Filter @{'Name'=$dvSwitchName}
  $dvSwitch.ReconfigureDVPort_Task($portSpec)
  

• Intel VGT vlan tagging

  Hi all

  I have an interesting dilemma, I inherited a virtual machine that is on several VLANs through VGT vlan tagging within the OS in the virtual machine and the vNic is labelled a trunk of vlan 4095 allowing him to pass all traffic vlan via and it's beautiful and functional as expected.  Now for my dilemma, I can't figure out how the previous admin (how is no longer here) installation and set the VLANs inside the OS of the machine virtual because there is no VLAN interface, nor any kind of vlan tab in the properties of the network card, or any sort of breakthrough in tablets that I can find , there is nothing in the start menu or in device management and etc...  I'm a puzzle about how he set up them VLAN in the first place, is there some hidden, Intel application I need to run?  I have the pilot VGT and installer that he used "pro2kxp_v14_0.exe" I can run again, but I am about this if I reinstall top that it would eliminate all the existing definitions of VLAN and there are about 15 VLAN which would be bad for me.  Any ideas or suggestions?

  Thanks in advance.

  To set up the guest operating system, you must install the Intel Proset software. Which, by the sounds of it, you do.

  To access the confiugration usually, you go to the Device Manager and then view the properties for the actual network card. Memory, you may need to do this from a Console session instead of the RDP as the software Intel connection cannot load in the Terminal Server services.

  -ben

• Configuration of VLAN Tagging

  I'm pretty new to VSphere, go to the install/configure in November class but had a consultant come do a show dog & Pony and he said we could do VLAN tagging to allow all our VLAN's communicate via a single distributed switch connected to a physical switch port 1. I can't get to work - can I get some advice on what I'm wrong? Attached screenshot - any help is appreciated

  Yes - 8 trade and assign each of them a single VLAN and then give them your virtual machines the portgroup appropriate.