REQUIRED: ISE 1.1.3 Posture Setup and Config Switch (ACL, dACL)

Similar Questions

• Cisco ISE posture assessment and client provisioning

  Hello

  I have the Cisco ISE and Cisco IOS device. I configured the RADIUS between these devices.

  Also, I configured RADIUSbetween ISE of Cisco and Cisco ASA. Now I want to know that how to posture assessment for these devices (ISE of Cisco and Cisco ASA or ISE Cisco Cisco IOS). Please give me the steps together for assesment for cisco ios device posture in Cisco ise.

  In addition, please give me related to posture assessment and the provisioning client logs.

  Thanks in advance.

  You can go through the list link below to download a PDF link

  Assessment of the posture with ISE.

  http://www.Cisco.com/Web/CZ/expo2012/PDF/T_SECA4_ISE_Posture_Gorgy_Acs.PDF

  ~ BR
  Jatin kone

  * Does the rate of useful messages *.

• Cannot install itunes for windows - error: Apple Application Support is required to run Itunes Helper. Uninstall and reinstall (as I did twice)

  Cannot install itunes for windows - error: Apple Application Support is required to run Itunes Helper. Uninstall and reinstall (as I did twice)

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• I hope someone can help me. I changed a few settings in the BIOS Setup, and now I have just a black screen. I changed the main boot to the DVD player device. is it possible to reset to original settings?

  I hope someone can help me. I changed a few settings in the BIOS Setup, and now I have just a black screen. I changed the main boot to the DVD player device.  is it possible to reset to original settings?
  I am running Windows XP

  clint341,
  Thanks for posting on the Microsoft Answers forum.  We cannot guide you more precisely by changing the BIOS settings that the BIOS settings are specific to your motherboard.  However, most (if not all) parameters of the BIOS have an option to restore the default BIOS (sometimes called "default opitimized").  It may be an option in the menu that you highlight, then press enter or it can be assigned to an F key and States at the bottom of the screen, press F? for the default settings.  I hope this helps.  If you are still not able to reset, check with the manufacturer of PC for more information about the BIOS. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I want to use an older version of Photoshop. I have the official copy, etc. of activation key. However, whenever I start Photoshop it requires registration. I tried internet registration and phone, but they seem to not work. Please tell us how regisyter t

  I want to use an older version of Photoshop. I have the official copy, etc. of activation key. However, whenever I start Photoshop it requires registration. I tried internet registration and phone, but they seem to not work. Please tell us how to register the product. It's Adobe Photoshop CS version 8 for Windows.

  The CS/CS2 activation servers have been removed. Download CS2 and use the new number given to the right of the download link.

  ml https://helpx.adobe.com/x-productkb/Policy-Pricing/Creative-Suite-2-activation-end-Life.HT

• Hi, I'm trying to update 'apps' in creative cloud Setup, and I'm just an endless loading spinner so I can't see or select one of my apps to update. Thanks for any help.

  Hi, I'm trying to update 'Apps' in creative cloud Setup, and I'm just an endless loading spinner so I can't see or select one of my apps to update. Thanks for any help.

  

  N ° 1)

  Launch the activity monitor and force them to leave Adobe all the processes like creative cloud, CoreSunc, AAMUpdater... etc.

  Step 2)

  (1) right-click on the icon in the Finder, then select 'Go - To' folder.
  (2) you will get a text box, type in the following command and then press the 'return '. ("Not to be missed ~ symbol")

  ~/Library

  It will open the folder of the user's library.

  (3) then navigate to Application Support > Adobe > OOBE. Open the OOBE folder and Opm.db bin file.

  Step 3)

  1) click the icon of the Apple menu and select System Preferences, and then click Network.
  (2) choose the network that is currently connected to the internet can you Ethernet or Airport (Wireless).

  (3) then click on the Advanced button, then click proxies.
  (4) slot 'Select a Proxy Server to configure' uncheck all the proxy check the boxes, then uncheck "Use FTP Passive Mode (PASV)".
  (5) then click on the Apply Now button.

  Restart the Adobe Creative Cloud and sign and select.

  Always the same?  Let me know.

• I have 2 accounts of adobe Setup and want to merge to 1. My Behance site is a different connection/e-mail than my creative cloud. So... When I'm connected to CC, I can't see my Behance site and updated. Can you please help?

  I have 2 accounts of adobe Setup and want to merge to 1. My Behance site is a different connection/e-mail than my creative cloud. So... When I'm connected to CC, I can't see my Behance site and updated. Can you please help?

  Please contact our support staff from the following link for assistance on this subject: https://helpx.adobe.com/contact.html

  (be sure to connect to adobe.com with your Adobe ID first)

• Difference between Local and central switching FlexConnect

  I'm trying to understand why you would use FlexConnect "Vlan based central switching", when you can just use Local mode? Please can someone explain the difference.

  I understand that you have a branch office environment, which required two LANs a local dial-up and wireless, one at the wire centre, but out of this scenario, why would you choose Vlan "based central switching?

  I have been using the following article to understand this topic:

  http://www.Cisco.com/en/us/docs/solutions/enterprise/mobility/emob73dg/ch7_HREA.html#wp1103053

  This is the limitation when you use FlexConnect compared to local mode

  http://www.Cisco.com/en/us/docs/wireless/controller/7.2/configuration/guide/cg_flexconnect.html#wp1241304

  Thank you

  Scott

  Help others by using the rating system and marking answers questions as 'response '.

• NSX design with cisco UCS/fabric interconnects and Nexus switches

  Hi Experts

  I am new to NSX design and deployment and working on a project. We deploy NSX for applications of level 4 (web, app, db, DC). I use logic, DLR, ESG and DFW switches. I next we intend to use roads static confusion..

  1. do we cover all the VLAN from the virtual to the physical environment? for example mgmt VLAN, level vlans(web,app,db), vxlan transport vlan or it should be only a VLAN specific?  which means would be I have set all the VLANS in environment NSX in my physical switching environment?

  2 vds? don't we create not only 1 vds initially during the deployment of vcenter or more? Should we take any special consideration while deploying to the deployment of the NSX?

  3 static routes - we configure static routes on the DLR and the GSS? Should I use the default routes upstream? on the physical router should we be routing all subnets from virtual environment to the GSS.

  4. where and who should create virtual machines? Via vCenter or before the deployment of the nsx NSX?

  5. we have a level of domain controller. Should it be part of 3 or separate applications with allow any any rule on DFW?

  Thank you

  Sam

  (1) the VLANs which exist for physical Machines span the logical switch VXLAN NSX in the following cases:

  • If the current deployment there are physical Machines in the same Vlan and subnet IP with Virtual Machines. If this common Port Vlan group is migrated to a switch logic VXLAN Backed port group and not possible to change the IP addresses of the virtual machines, and then a bridge DLR (Distributed logical router) works as the conversion between Vlan physical and virtual VXLAN
  • If Conversion of P-to-V of the physical Machines continue on this Vlan

  VLAN which cover only the virtual machines or virtual local networks which cover only physical Machines must not be delayed.

  (2) for the deployment of the NSX, there may be more than 1 dVS or only 1 vDS according to the design. There may be another type of traffic other VXLAN base of virtual machines such as backup, storage, VMotion and the overall design, management, best practices apply here as well.  A requirement of the NSX is a common VDS that spans the entire Cluster. For each Cluster, this "common VDS' may be different. Yet once this VDS maybe a separate VDS dedicated VTEP or VTEP features functionality can be added to the existing VDS. It may be best to separate the VTEP vDS.

  (3) for the DLR, a default gateway is usually sufficient. If static routes are used, the GSS must then drive by default upstream and the static routes with the next hop of the DLR downstream for the subnets in the subnets IP VM logical switch. On the physical router static route to the VM, but also DLR - ESG logical subnets Subnet switch is required. Management of static routes is easier if route summarization is possible, or if necessary, close to the IP subnets, so it may be a good idea to use the dynamic routing such as Ospf or BGP protocol. There are also features of IP address management in Vrealize and other IPAM solutions if Automation is necessary for large and dynamic environments.

  (4) NSX has no functionality in the creation of the VM, it only creates Services network such as switches, routers, Firewalls, Load Balancing. The creation of the part VM continiues the same way as before. A point to note is maybe the logic is created appear as VXLAN named port groups on the VDS. NSX Manager creates groups of ports on the VDS, the only difference is that the name includes VXLAN. The virtual machine is like before added to this group of VXLAN Backed Port settings, or added to the logical switch from NSX Manager interface that appears again as a Plugin for VCenter. VCENTER is so point to create virtual machines and add these VMs to the logic is.

  (5) level of domain controller can be a separate layer, or other third party, may be preferable to upgrade separated except 3 applications. Usually, it's the same design without NSX. dFW rules can help protect the domain controller with allowing only ports of the virtual machine or physical Machines being admitted. dFW rules can apply to VXLAN based logical switches NSX so that VLAN based DVS Port groups because it's the kernel module.

• Reset home folder permissions and the default ACL on macOS Sierra?

  A tool that I've used in the past to troubleshooting doesn't seem to be available in macOS Sierra.

  There was a procedure in el captain to reset the permissions of file and ACLs in start in recovery mode, by running the command terminal, resetpassword.  This command pulls up a GUI in Sierra as el cap but the "reset the user permissions and ACLs" option is no longer there.

  This article describes the procedure to el captain

  http://appletoolbox.com/2016/07/fix-corrupt-user-accounts-MacOS/#For_El_Capitan _ andmacOS

  Is there another way to reset the permissions of the user and the default ACLs on macOS Sierra?

  If you are looking for in the forums on the topic and limit to messages by Linc Davis, he posted a script that will reset everything.

• Firefox is not fully load site Barclaycard of authentication. It load regarding the demand for certain letters in my password but does not load the button 'Submit', so I can't continue with my purchase and I switch to IE8 browser to buy whatever it is ov

  Firefox is not fully load site Barclaycard of authentication. It load regarding the demand for certain letters in my password but does not load the button 'Submit', so I can't continue with my purchase and I switch to IE8 browser to buy anything on the internet. Clues?

  This has happened

  A few times a week

  Is a few weeks ago

  Your UserAgent string in Firefox is totally messed up by another program that you have installed and Barclays does not know you use Firefox 3.6.6 - it is probably similar to IE 6.0 on this site.
  http://en.Wikipedia.org/wiki/USER_AGENT

  type of topic: config in the URL bar and press ENTER.
  If you see the warning, you can confirm that you want to access this page.
  Filter = general.useragent.
  Preferences are "BOLD", a line at a time, and then select reset, right click
  Then restart Firefox

• CiscoWorks LMS 4.0.1 and 3850 switch support

  HI, I want to know if the 3850 switch is supported in ciscoworks LMS 4.0.1 I added devices, successful inventory collections but peripheral icon is blue with question mark '? ' and config sync always fails.

  I tried to download the packages to install it, but I couldn't find it.

  Thanks help fo

  3850 is supported on LMS 4.2.3. Check the list supported here:

  http://www.Cisco.com/en/us/docs/net_mgmt/ciscoworks_lan_management_solution/4.2.3/device_support/table/lms423sdt.html

  You must upgrade to 4.2.3 LMS or 1.3 FT go.

  -Thank you

  Vinod

  *Side encourages contributors and it's really free. **

• H - HARVEST and local switching issue (LAN)

  Cisco documentation indicates that H-REAP is designed for WAN environments, but I'm interested in the use of REAP H and local switching in a LAN environment. Basically want to control and data + auth traffic are separated.

  Also because the controller is local that I have to use H-REAP, I can just do local switching?

  Does anyone have experience with this?  All suggestions, feedback will be much appreciated.

  Hi Mohammed;

  Yes, local switching is a sub-feature of REAP H so it must be HREAP to local switching.

  The only advantage that you find using the local switching without WAN is that you don't need a big connection to the WLC since it will not process the data traffic, so you can plug a port of the WLC only. Depending on how your network look like, enlighten you really the network between APs and WLC, because traffic goes directly from AP to the destination, without transiting by for WLC.

  On the other hand, you lose the advantage of having a roaming and similar advantage brought by the WLC couche3 WLC.

• Defining a router and 2 switches in a network

  Hello!

  I have a question, please reply as soon as possbile.

  Look, I'm new in routing, just lerning, CCNA Discovery course, there is the problem:

  

  well, I'll put in place a ROUTER and 2 switches, I have set up in terminal:
  the end result, we have:
  ETH 0/0 (from where internet is coming) - IP - 192.168.100.200
  ETH 0/1 (inside the network) - IP - 192.168.80.1

  Also, I configured the same way ARP:
  Slash rip router (config) #.
  slash network (config - router) # 192.168.100.0 / / IF I understand ARP allows data transffer beetween networks and make it visible on the other

  slash network (config - router) # 192.168.80.0

  now, if the two devices end network (PC), I ping the ping works and the package was sent and received.
  !!!! THE PROBLEM IS > why I can't ping (PC0) 192.168.100.201 the 192.168.80.2 (PC1)
  the INVESTIGATION period was made.

  There are in tie my tracert schema package. Thx for the reply and attention!

  you have the default gateway configured on the two PCs?

• Where file AUTOEXEC. BAT AND CONFIG. SYS FILES ARE

  IAM using DELL inspiron 20 3043 ALL IN the OFFICE. In this desktop computer with windows OS 8.1.

  I want to know AUTOEXEC. BAT and CONFIG. SYS files and how to edit and edit these files in my office.

  Thanking you.

  Autoexec.bat and config.sys are older MS-DOS configuration files for 35 years and do not apply to windows 7, 8 or 10.