CiscoWorks LMS 4.0.1 and 3850 switch support

Similar Questions

• ACS and Brocade switch support!

  Hi Experts,

  I have two questions: -.

  (1) does support switch of Broacade CSA?

  (2) I am configuring a Brocade switch for Radius Authentication on an ACS server. But the right to the user and not a right admin?

  Can you please tell me how to assign the admin for brocade switch?

  Thanks in advance.

  Concerning

  Neha.

  Configure the ACS unit to import your CSV

  A. go to the Interface of Configuration > Advanced Options

  B. check RDBMS synchronization and click on submit

  C. go to the System Configuration > RDBMS synchronization

  D. Enter the name of the CSV in the Actions file field

  E. Enter the IP of the server FTP, the directory where the CSV file resides on the server FTP and the username and password for ACS to use to access the FTP server in the fields suitable

  F. choose manual synchronization

  G. make sure your server is listed in the column to synchronize synchronization partners section and click on submit

  H. go back into the RDBMS synchronization and click Synchronize now and updates must take place.

• CiscoWorks LMS 4.1 monitor temperature

  Hello everyone!

  I am creating a poller to monitor the trap of the temperature of my cisco catalyst 2960 Ciscoworks LMS 4.1.

  I created a snmp trap on my device:

  Switch(conf-t) # snmp-server <@IP_server_LMS>SNMPv2c host -I use SNMPv2c

  Switch(conf-t) # Server enable snmp traps envmon temperature

  I created a MIB model Envmon with these variables:

  -ciscoEnvMonTemperatureThreshold

  -ciscoEnvMonTemperatureStatusValue

  -ciscoEnvMonTemperatureState

  -ciscoEnvMonTemperatureLastShutdown

  I created a poller associated with my model, I add my device and when I click on 'Next', I have this error message:

  ###

  No instance are in the devices. This could be because the device is inaccessible, the device does not have the case for selected models or the timeout value is low.

  ###

  Could someone explain to me why I can't monitor MIB?

  Thanks for your consideration and Merry Christmas to all!

  It seems that most of the 2960 have a temperature sensor implemented in hardware and therefore, it shows no values.

  If a device does not show anything on CLI, it is almost impossible that it will display something via SNMP.

  -Thank you

• CiscoWorks LMS 3.2 exporting bulk Configuration

  Hello

  Does anyone know an easy way to bulk export configurations off Ciscoworks LMS 3.2?  The only thing I found is the cli command export config u cwcli.exe - p-unit %, but it exports in XML format which is not very readable.  Prefer a text file format.  Someone at - it suggestions?

  Thank you

  Brian

  Hi Brian,.

  CLI, it is the only option, but what you can do to get the files in TEXT format is, you can connect to the server and

  go to this site: NMSROOT\CSCOpx\files\rme\dcma\shadow

  and

  NMSROOT\CSCOpx\files\rme\dcma\devfiles

  Thank you-

  Alya

  * Sides encourage contributors *.

• First management LAN CiscoWorks LMS or Cisco? Help

  In my business, we look adds a network management solution:

  Some time ago, we installed CiscoWorks LMS 3.2, but we decided to install on the other more modern solution, what is the solution which recommend me?

  Requeriments:

  1 000 devices from cisco management.

  Regularly perform massive configurations.

  Constant monitoring of the network infrastructure.

  Backups of configuration.

  We have two solutions:

  -Update the current CiscoWorks to LMS 4.x version

  -buy the "First Cisco LAN Management" Solution

  What solution that recommend me?

  Thank you for your attention.

  Kind regards.

  Hi Jeffersson,

  The current product packaging is a bit confusing. Cisco is rebranding all of their management under the aegis of the first Cisco solutions. All prime products have a common appearance and take advantage of some approaches architectural.  From LMS 3.2 on 4.x will put you in the first territory of Cisco.

  In the 'first' products are (among others) "Cisco first Infrastructure" (also known as PI - 1.2 is the current version) and "Cisco first LMS" (4.2.3 is current). Preferred Infrastructure (1.0) began in the successor to management wireless Cisco (NCS) product and had been adding features on the way to bring it up to parity with LMS functionality to wired infrastructure. He isn't quite there right now (current comparison here) that existing customers of LMS are usually advised to stick with the latest version of the LMS for now.

  Still with me? Good. If the extra twist is that 4.2 LMS is "included" with licenses of FT 1.2 - see the link guide below. So, if you want LMS 4.x, you order indeed 1.2 FT with licenses "Cycle of life" according to the number of devices you manage. (There also is 'respect' and 'insurance' adding these new features of the respective licenses. Compliance is available from LMS 4.2 in the CAAM.  Insurance is almost a FT 1.2 functionality only.)

  So my recommendation to you would be to upgrade to version 1.2 of PI and to install and to use the LMS 4.2 (4.2.3 and put patched up-to-date with all the packaging of the products). If you have a VMware configuration, deployment option flexible device (file eggs) is the easier implementation,.

  You may find it useful to explain this point of view of Cisco the following two links:

  Functional reference LMS

  Control of IP and Licensing Guide

  Don't worry not-all this will not be on the test.

• trunk fiber 3750 and 3850

  I currently have two 3750's (bunk). We recently bought two new 3850's and have stack as well. My question is, how to I master them? I want to be able to use the new switches with the same VLAN and IP addresses as the existing. The new switches are in the same basket as existing ones.

  The current 3750 are the gateway to my network (and they remain such, for now).

  I plugged an uplink to switch fiber as in:

  3750 (IG 1/0/49)--> 3850 has (IG 1/1/1)

  3750 (IM 2/0/49) b--> 3850b (IM 2/1/1)

  I gave the fiber ports the following parameters:

  3750 a:
  int item in gi1/0/49
  trunk program dot1q switchport
  switchport trunk allowed vlan add ALL
  switchport mode trunk
  switchport nonegotiate

  3750b
  int gi2/0/49
  trunk program dot1q switchport
  switchport trunk allowed vlan add ALL
  switchport mode trunk
  switchport nonegotiate

  3850a / 3850b:
  Item in gi1/1/1
  Gi2/1/1
  switchport trunk allowed vlan add ALL
  switchport mode trunk
  switchport nonegotiate

  At this point, I thought I'd be able to ssh in the new (3850) switch and ping current (3750), but I can't. Assistant network on the switch curent 3750 'sees' the new 3850, but has he appears as "unsupported device". The switches are on the same subnet (10.11.1.0/24).

  Tandem switch (3750) is 10.11.1.2 and new 3850 is 10.11.1.14. If I connect my laptop on the 3850 and give me an IP 10.11.1.x, I ping the switch itself (10.11.1.14), but I can not ping to the gateway (10.11.1.2). If I SSH in switches, I can not ping each other.

  Do I need to set up the uplink fiber as an Etherchannel? Or are my settings incorrect switchport? I don't know what I'm missing. I'm certainly not an expert in the field, even if its something that may be obvious to others, it's quite possible I forgot.

  Hope it makes sense. Any suggestion would be appreciated. Thank you.

  Hey,.

  Provide the following information to learn more:

  3750 side:

  #sh ip int br | ex-United Nations

  #sh int g1/0/49 trunk

  #sh int g2/0/49 trunk

  #sh vlan br

  3850 side:

  #sh ip int br | ex-United Nations

  #sh int g1/1/1 trunk

  #sh int g2/1/1 trunk

  #sh vlan br

  Kind regards
  RS.

• Firefox is not fully load site Barclaycard of authentication. It load regarding the demand for certain letters in my password but does not load the button 'Submit', so I can't continue with my purchase and I switch to IE8 browser to buy whatever it is ov

  Firefox is not fully load site Barclaycard of authentication. It load regarding the demand for certain letters in my password but does not load the button 'Submit', so I can't continue with my purchase and I switch to IE8 browser to buy anything on the internet. Clues?

  This has happened

  A few times a week

  Is a few weeks ago

  Your UserAgent string in Firefox is totally messed up by another program that you have installed and Barclays does not know you use Firefox 3.6.6 - it is probably similar to IE 6.0 on this site.
  http://en.Wikipedia.org/wiki/USER_AGENT

  type of topic: config in the URL bar and press ENTER.
  If you see the warning, you can confirm that you want to access this page.
  Filter = general.useragent.
  Preferences are "BOLD", a line at a time, and then select reset, right click
  Then restart Firefox

• H - HARVEST and local switching issue (LAN)

  Cisco documentation indicates that H-REAP is designed for WAN environments, but I'm interested in the use of REAP H and local switching in a LAN environment. Basically want to control and data + auth traffic are separated.

  Also because the controller is local that I have to use H-REAP, I can just do local switching?

  Does anyone have experience with this?  All suggestions, feedback will be much appreciated.

  Hi Mohammed;

  Yes, local switching is a sub-feature of REAP H so it must be HREAP to local switching.

  The only advantage that you find using the local switching without WAN is that you don't need a big connection to the WLC since it will not process the data traffic, so you can plug a port of the WLC only. Depending on how your network look like, enlighten you really the network between APs and WLC, because traffic goes directly from AP to the destination, without transiting by for WLC.

  On the other hand, you lose the advantage of having a roaming and similar advantage brought by the WLC couche3 WLC.

• Defining a router and 2 switches in a network

  Hello!

  I have a question, please reply as soon as possbile.

  Look, I'm new in routing, just lerning, CCNA Discovery course, there is the problem:

  

  well, I'll put in place a ROUTER and 2 switches, I have set up in terminal:
  the end result, we have:
  ETH 0/0 (from where internet is coming) - IP - 192.168.100.200
  ETH 0/1 (inside the network) - IP - 192.168.80.1

  Also, I configured the same way ARP:
  Slash rip router (config) #.
  slash network (config - router) # 192.168.100.0 / / IF I understand ARP allows data transffer beetween networks and make it visible on the other

  slash network (config - router) # 192.168.80.0

  now, if the two devices end network (PC), I ping the ping works and the package was sent and received.
  !!!! THE PROBLEM IS > why I can't ping (PC0) 192.168.100.201 the 192.168.80.2 (PC1)
  the INVESTIGATION period was made.

  There are in tie my tracert schema package. Thx for the reply and attention!

  you have the default gateway configured on the two PCs?

• H - HARVEST in central auth and local switching has any backup auth method?

  Hello

  In REAP: solution with central authentication and local switching, do we have any fallback, authentication method in the case of the controller failure or WAN link to controller fails. As authentication WPA/WPA2 PSK for LWAPP REAP H in stand-alone mode.

  Thank you

  Arun

  What guarantees do you intend to use?

  If you are using PSK, you're fine as the live keys on the AP. So if you lose the controller, customers will always authenticate. If you use 802. 1 X, it's another story.

• CISCOWORKS LMS 2.5 SP2

  Hello

  The apps were running smoothly, but after a suddenly cut power that affected the (stand-alone) server, it was not possible to loggin again.

  We got the login screen, but after typing user/passwd, appears a blank screen (done) and nothing else.

  Each process runs normally, except the process = EssMonitor = ESS Info is entirely online!

  Can you guide me to solve this problem?

  Thank you very much

  regdaemon. XML has been damaged. It is therefore more correct XML. It was probably truncated in the feeding tube. If you don't have a good backup of LMS, you must uninstall and reinstall LMS from scratch. You will not be able to preserve your data because restore this file regdaemon.xml will corrupt so all future installations.

• NSX design with cisco UCS/fabric interconnects and Nexus switches

  Hi Experts

  I am new to NSX design and deployment and working on a project. We deploy NSX for applications of level 4 (web, app, db, DC). I use logic, DLR, ESG and DFW switches. I next we intend to use roads static confusion..

  1. do we cover all the VLAN from the virtual to the physical environment? for example mgmt VLAN, level vlans(web,app,db), vxlan transport vlan or it should be only a VLAN specific?  which means would be I have set all the VLANS in environment NSX in my physical switching environment?

  2 vds? don't we create not only 1 vds initially during the deployment of vcenter or more? Should we take any special consideration while deploying to the deployment of the NSX?

  3 static routes - we configure static routes on the DLR and the GSS? Should I use the default routes upstream? on the physical router should we be routing all subnets from virtual environment to the GSS.

  4. where and who should create virtual machines? Via vCenter or before the deployment of the nsx NSX?

  5. we have a level of domain controller. Should it be part of 3 or separate applications with allow any any rule on DFW?

  Thank you

  Sam

  (1) the VLANs which exist for physical Machines span the logical switch VXLAN NSX in the following cases:

  • If the current deployment there are physical Machines in the same Vlan and subnet IP with Virtual Machines. If this common Port Vlan group is migrated to a switch logic VXLAN Backed port group and not possible to change the IP addresses of the virtual machines, and then a bridge DLR (Distributed logical router) works as the conversion between Vlan physical and virtual VXLAN
  • If Conversion of P-to-V of the physical Machines continue on this Vlan

  VLAN which cover only the virtual machines or virtual local networks which cover only physical Machines must not be delayed.

  (2) for the deployment of the NSX, there may be more than 1 dVS or only 1 vDS according to the design. There may be another type of traffic other VXLAN base of virtual machines such as backup, storage, VMotion and the overall design, management, best practices apply here as well.  A requirement of the NSX is a common VDS that spans the entire Cluster. For each Cluster, this "common VDS' may be different. Yet once this VDS maybe a separate VDS dedicated VTEP or VTEP features functionality can be added to the existing VDS. It may be best to separate the VTEP vDS.

  (3) for the DLR, a default gateway is usually sufficient. If static routes are used, the GSS must then drive by default upstream and the static routes with the next hop of the DLR downstream for the subnets in the subnets IP VM logical switch. On the physical router static route to the VM, but also DLR - ESG logical subnets Subnet switch is required. Management of static routes is easier if route summarization is possible, or if necessary, close to the IP subnets, so it may be a good idea to use the dynamic routing such as Ospf or BGP protocol. There are also features of IP address management in Vrealize and other IPAM solutions if Automation is necessary for large and dynamic environments.

  (4) NSX has no functionality in the creation of the VM, it only creates Services network such as switches, routers, Firewalls, Load Balancing. The creation of the part VM continiues the same way as before. A point to note is maybe the logic is created appear as VXLAN named port groups on the VDS. NSX Manager creates groups of ports on the VDS, the only difference is that the name includes VXLAN. The virtual machine is like before added to this group of VXLAN Backed Port settings, or added to the logical switch from NSX Manager interface that appears again as a Plugin for VCenter. VCENTER is so point to create virtual machines and add these VMs to the logic is.

  (5) level of domain controller can be a separate layer, or other third party, may be preferable to upgrade separated except 3 applications. Usually, it's the same design without NSX. dFW rules can help protect the domain controller with allowing only ports of the virtual machine or physical Machines being admitted. dFW rules can apply to VXLAN based logical switches NSX so that VLAN based DVS Port groups because it's the kernel module.

• I have items 12 and since switching to Windows 10 I can't print my photos from Elements. Is this version of Elements is compatible with windows 10

  I have items 12 and since switching to Windows 10 I can't print my photos from Elements. Is this version of Elements is compatible with windows 10

  jacquesd96006740 wrote:

  I have items 12 and since switching to Windows 10 I can't print my photos from Elements. Is this version of Elements is compatible with windows 10

  If you use version 12 except pour Print, the problem is to know what is special for your printer. I have no problem with version 12 and win 10 on HP and Epson printers.

  You can print from applications other than PSE12?

• difference between standard and disturbed switch

  What is the difference between standard and disturbed switch?

  What is locate these files confutation.

  Hi friend

  See below blogs:Difference is very well explained

  http://www.vmwarearena.com/2014/01/vSphere-distributed-switch-part-3.html

  http://www.tech-tap.com/2009/05/30/differences-between-vSwitches-and-dvswitches/

• I just tried to reinstall Acrobat 9.0 on my Mac. I'm going to the message I had the serial number does not match to. I bought for Windows in 2010 and he switched to Mac using Adobe. I now cannot install and this forum was fired by news

  I just tried to reinstall Acrobat 9.0 on my Mac. I'm going to the message I had the serial number does not match to. I bought for Windows in 2010 and he switched to Mac using Adobe. I now cannot install and this forum has been returned by the current agent. Can someone please? I don't have the funds to buy it again. Thank you.

  You can only do it in 1 or 2 years after purchase.  If you don't have that you received a serial number mac.

  check your account, Adobe ID Code

  If she is not there and you don't have to record the serial number of your mac on and fix you is perhaps not able to activate acrobat 9, but there is a chance adobe support would help.  Contact adobe during the time pst support by clicking here and, when available, click on "still need help," https://helpx.adobe.com/contact.html