Reset my router & get a DNS error?

Similar Questions

• After having configured my computer to obtain an IP address manually, I get a DNS error when trying to get online.

  Windows XP - Internet problem connection

  I have a wired internet connection through a cable company, initially, the message was limited connectivity, after a week of talking to their technicians no answer to the problem.  Finally through the running cmd I got the ip address, I entered manually, and it shows that I am connected but when I try to go on the internet it showsdns problem. I got the dns server address and entered manually but I still have no internet. Can you help me?

  original title: I can't connect to the internet.

  Hello

  1. What is the full and exact error message?
  2. don't you make changes on the computer before this problem?

  Read the following article that may help you resolve this problem.
  How to troubleshoot possible causes of Internet connection problems in Windows XP
  http://support.Microsoft.com/kb/314095

• Connection PS3 (DNS error)

  I cannot connect my ps3 to my Wireless Linksys WRT160N router. The router does not have a version type, so I guess it's version 1.0?

  Whenever I try to connect my ps3 I get a DNS error (80710102) of the playstation. I tried to use the automatic settings and manual settings. My laptop connects fine, but my PS3 doesn't even bother. During the settings auto, he will not even get an IP address, but when I entered this manually, it worked. However, I had no luck with typing manually DNS settings. It fails every time. Help, please!

  Thank you

  James

  First of all every time that you assign a static Ip address to your PS2, the IP address must be different from your computer, if you enter the same IP address, and then due to IP address conflict, it will make your Deivce work offline.

  Check the settings of your router wireless? It can be due to a higher level of security on your router. Connect to the router configuration page and click on the Wireless tab, and then click the sub-tab under wireless "Wireless Security" and below, change the Security Mode 'WPA discover' and under 'Passpharase' enter your password and click on save settings... "

  Now on your PS3, first remove the static IP address and then look for the wireless network and then trying to connect to it. Once connected to the wireless network your PS3 should be able to go online.

• Updated ReadyNAS 316 OS, returned with the DNS error

  I've recently updated as well to my NAS 6.5.2 devices and since doing so, the VA started sending notifications, update attempts failed. When I investigated further, I discovered that none of the functions of the update seems to work. For example, when I click to search for updates to the NAS operating system rather than show 6.6.0 or tell me there is no update he insteads returns a DNS error. My network has not changed in any other respect. 2 devices still sync with eachother and all my users can still access their data in the two places for the more basic functions appear to be not affected. I have manually updated them to 6.6.0 OS but the OS DNS error update remains on this device. I noticed that at some point the AV definitions that update before the manual up-to-date operating system and now it seems to work (for the moment) very well. However, as I have already said, the error remains the update of the OS. Rather than report the status update I get a DNS error.

  Thoughts anyone?

  A friend today got the same problem after the update of the firmware.

  Try turning off IPv6 support on your network interfaces.

  It has resolved the issue.

• E4200 and WDTV live via wifi without DNS error?

  Someone does it, I mean EVERYONE, got a WDTV live hub to successfully connect to the E4200 via wifi without getting a DNS error?

  My system:

  E4200, fw c. 2.1.39.145204

  WDTV Live Hum, fw c. 3.08.14

  DWA-160 (Rev.) (A) usb wifi dongle fw v. 1.80

  My sony wifi equipped blueray connected to the E4200 without boredom and access the USB HDD connected to the E4200.

  Any help, suggestions, comments are welcome.

  
  

• new router = dns error after running over and over again, Network Diagnostics only a page appears, and then stops. tried to reset IE8 on XP tablet

  changed «sharing data...» ', looked already several answers... all other laptops (4) adapted for the new router & modem with no problems...

  When you run the network diagnostics I can connect to the internet once, but trying to follow the link or open the second window provides DNS error and kill the connection.
  last error now from network diagnostics is error 0x5b4 to query the server DNS 192.168.1.1; DNS not found, not a home user scenario...
  any other idea?

  Hello

  You did changes to the computer before the show?

  Please follow the steps mentioned in the link below.

  http://support.Microsoft.com/kb/314095

• Can not get on the net via wifi apt, dns error msg

  Howdy, hey i cant get on the net with any browser through my wifi apt. I can very well with any other wifi in the range but my wifi apt has the best signal. I get a msg of DNS server and tried everything that the computer recommended to fix. Why this only happen with wifi at my complex?

  SteveAustin71,
  Thank you for visiting the Microsoft Answers community forum.

  When you say that your wifi apt, it's your own personal network or provided by a complex of apartments for the residents?  Is that what you must pay for, or is it a free hot spot?  What is you get the exact error message?  If it's your personal network in your own apartment, what type of router is and is it secure?  If it is fixed, what kind of security it uses?  Answers to these questions will help us better diagnose your problem and propose solutions.

  DNS errors can mean different things, depending on what is the exact error message, but generally means that your computer does not have the DNS information from the router or server that is supposed to provide the IP address, gateway and DNS information on the computer when you log on.

  Let us know the answers to these questions so that we can better help you.
  Thank you

  Gloria
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• DNS error with wired router

  When I first bought a PS3, I needed a router to access the internet for my PC and my PS3. It worked fine for several months and then one day, that my router is no longer me connected to the internet. Currently I am connected to the internet directly from my modem which means that it is not my ISP that has the problem. When I connect the router it says that there is some sort of DNS error. Help?

  What is the model of the router?

  Are you on the computer or on the... PS3 DNS error ?

  On the computer, click on start > all programs > Accessories > guest... A black box will appear (command prompt)... In the command prompt window type ipconfig and press "Enter"... Look for Ethernet adapter Local Area Connection address IP, subnet mask, and default gateway... IP address must be 192.168.1.x, subnet mask: 255.255.255.0 default gateway: 192.168.1.1 (assuming that your router is 192.168.1.1)...

  If you get mentioned above IP address, a subnet and address the gateway then you ping the gateway, type ping 192.168.1.1 and press ENTER... If she gives you ask has expired, and then disable any firewall, the security software on the computer...

  If you get 4 replies then type ping 4.2.2.2 and press ENTER, if you get the request exceeded, then you must update the firmware on your router... If you get 4 replies then type ping yahoo.com and press ENTER... If you get answers from Yahoo, then you should get the Internet after adjusting the browser settings...

  Setting of the browser settings: open an IE, click on tools > Internet Options, and then delete all files, cookies, history, forms... GoTo 'Connections', make sure that never Dial a connection is selected, click on network settings and make sure that all the options are unchecked... Once you are finished, click OK... Close IE and reopen...

  If yahoo expires, provide static DNS on your connection to the local network...

  Click the Start button > settings > Panel > Network Connections - right click on Local area connection icon and go to properties On the "Général" tab, select "TCP/IP Internet Protocol" and click on the properties button - select "Use the following DNS parameters" DNS preferred 192.168.1.1 DNS auxiliary - 4.2.2.2 > Click on the button Ok to save and click on 'Close' in the main window of properties... You should be able to go online...

• My internet keeps disconnecting even if the router works fine. He maintains have diagnosed as a DNS error any.

  I have a Samsung RV511 which is only a couple of years.  It has been disconnected from the internet every 2 to 5 minutes or more, but my router works fine.  I got a new power cord, ethernet for her, but the computer continues to disconnect. When I diagnose the problem, it indicates the server DNS does not.  Tried to contact my internet provider, but they couldn't understand why I didn't know every little thing on my computer and made me feel pretty stupid so I'm curious to see if anyone else out there it can help.

  I used to get this problem.  My connection would get a yellow top warning symbol & I could no longer communicate on the internet.  No Windows diagnosis could correct & would only sometimes identify [as a DNS problem].

  I searched for advice, but never really found a convincing explanation or an appeal.  I started using the commands below [that I found in this forum] to restore things.  It seemed most of the working time.

  Several people also suggest just reset the router, but that was irrelevant, because I haven't used one but I tried to remove and then reconnect the modem USB and sometimes helped.

  The problem seems to occur in phases, but I could never understand what was different between the good times & bad times.  I've always suspected the software controlling my USB modem but could never be sure.  I changed the USB modem & the problem went away for months before returning [but less frequently than before].  Now, I have a wireless connection with my mobile phone and use it as my modem for internet connection - 5 months without problem.

  What I did was to open a command prompt [I think he should be executed as administrator], then type:

  netsh winsock reset
  RESTART THE PC
  netsh int ip reset
  RESTART THE PC
  ipconfig/flushdns
  ipconfig/registerdns
  RESTART THE PC

  As I say, this procedure allows to sort out most of the time, but it should reappear later.

• Always get "an unknown error has occurred." When you try to reset the password.

  I got an email from iCloud and forgot his password. I'm 100% sure that safety issues are correct, but always gets "an unknown error has occurred." pop up when I press continue after having answered the questions. What answer I go, good or bad, will give me the same error. I can't reset by email because the enamel of rescue is the iCloud himself account. How can I fix? Thank you.

  Enter your Apple ID and click on I forgot the password,.

  Apple ID - manage

• I have to reset my router to get the new speed

  I have a Linksys EA6500 router.  My internet provider has recently increased their internet speeds without expenses.  I had a plan with a download speed up to 15mbps.  Now it should be 30.  I did a speed test and still get only 15.  I called my provider and they forced me to direct connect my modem to my computer and then I got 30.  She told me that I might have to reset my router to synchronize it with the faster speeds more recent.  I tried to unplug and repluging and that did not help.  Is there another way to get the router to recognize the new speed without going through the hassle of a hard reset?

  try to go to the prioritization of media and then click on settings (blue link) and then see what speed is set on it. It should be 1024 x 30 or possibly 0. Set and save it. usually a reset as you could clear up tho. worst case you may need to do a factory reset and the config from scratch. But first try the number

• I get the error "on the volume C: default transaction resource manager encountered an error during startup and its metadata has been reset. The data contains the error code. »

  original title: NTFS problem
  Every 5 seconds, I get a warning (event ID 136) that says: "on the volume C: default transaction resource manager encountered an error during startup and its metadata has been reset. The data contains the error code. »

  Immediately followed by an error (event ID 137) that says "on the C: volume default transaction resource manager encountered a one-time error and could not start. The data contains the error code. »

  I am running windows 7 ultimate in any way to solve this problem?
  

  Hello

  This problem occurs if the Windows file system transaction log is damaged. The Windows file system uses the transaction log to retrieve the system transactions when a file error occurs. The system of common log (CLFS) transaction logs may be left in an inconsistent state. When the CLFS transaction logs are in an inconsistent state.
  To resolve this problem, delete the files .blf and .regtrans-ms in the folder % Windir%\System32\SMI\Store\Machine.
  After you restart the computer, the registry regenerates the deleted files. These regenerated files are in a consistent state.
  1. click on Start , type cmd in the Search box, and then click cmd in the list of programs .

  2. click on run as administratorand then click continue.
  If you are prompted for an administrator password or for confirmation, type the password, or click allow.

  3. at a command prompt, type the following command and press ENTER:
  fsutil resource setautoreset true c:\
  Note these steps assume that Windows is installed in the default location, drive C. If this is not the case, adjust the drive letter of the path of the folder to match your configuration.

  4 restart the computer.

  I hope this helps.

• Removing static route get % corresponding to any error no route to remove

  I'm trying to remove a static route, I added:

  -------------------------------------------------------------------------------------------------

  R2 #show ip route
  Code: C - connected, S - static, mobile R - RIP, M-, B - BGP
  D - EIGRP, OSPF, IA - external EIGRP, O - EX - OSPF inter zone
  N1 - type external OSPF NSSA 1, N2 - type external OSPF NSSA 2
  E1 - OSPF external type 1, E2 - external OSPF of type 2
  i - IS - Su - summary IS, L1 - IS - IS level 1, L2 - IS level - 2
  -IS inter area, * - candidate failure, U - static route by user
  o - ODR, P - periodic downloaded route static

  Gateway of last resort is not set

  172.168.0.0/29 is divided into subnets, subnets 1
  S 172.168.0.0 [1/0] via 192.168.2.2
  C 192.168.1.0/24 is directly connected, FastEthernet0/0
  192.168.2.0/30 is divided into subnets, subnets 1
  C 192.168.2.0 is directly connected, Serial0/0
  R2 #conf t
  Enter configuration commands, one per line.  End with CNTL/Z.
  R2 (config) #no ip route 172.168.0.0 255.255.255.0 192.168.2.2
  % Corresponding to any no route to remove
  R2 (config) #r2 #show ip route

  ----------------------------------------------------------------------------------------------------

  I was training establishment of a static routing on three routers r2 (2600xm) connected to r1 (2600xm) via maps module T1 on the serial ports. connected to r1 is a router 2500 old called PC.

  I removed the static routes off r2 and PC but when I get to r2 I connect to 2500 another console cable that I use to access a server I get the above error.  all IP addresses are just generic subnets that I created to play with static routing.   I can't remove someone has any ideas?

  you use the subnet mask different than the one you used. According to the route table entry mask is 29

  Try this,

  1] r2 (config) #no ip route 172.168.0.0 255.255.255.248 192.168.2.2

  or 2] another easy method would be to check the working config and copy stick with 'no' at the beginning.

  See the race | include the ip route

  Copy the static route statement and paste this what with 'no' in the global configuration and check the routing table.

• I can not connect with my BC password. I tried to reset and all I get is an error. I can not even find a support option to solve the problem. Anyone know anything I can do?

  I can not connect with my BC password. I tried to reset and all I get is an error. I can not even find a support option to solve the problem. Anyone know anything I can do?

  Hello

  Just sent you a personal message

  Let me know if you have any question.

• Often, I get the message error "Firefox cannot find the server.

  Often, I get the message error "Firefox cannot find the server. Page normally, refresh the page to load, even if sometimes it takes more than one try.

  I checked my connection settings. IPv6 and DNS prefetching are disabled, according to the recommendations in this article: https://support.mozilla.com/en-US/kb/Firefox%20cannot%20load%20websites%20but%20other%20programs%20can?s=Firefox+can%27t+find+the+server+at & r = 1 & as = s

  See also:

  • http://KB.mozillazine.org/Error_loading_websites
  • https://support.Mozilla.com/kb/error+loading+Web+sites

  You can try to reset (power off / on) of the router.