DNS error with wired router

Similar Questions

• PIX 501 DNS resolution with static route

  I use a pix 501.

  I have an internal DNS server behind the pix that uses my DNS of the ISP servers to resolve external domains.

  Now, I want to host a web site on the same server.

  To allow external access to the web server, I add the following:

  outside_in_http list access permit tcp any host A.B.C.D eq www

  static (inside, outside) A.B.C.D L.M.N.O netmask 255.255.255.255 0 0

  Access-group outside_in_http in interface outside

  It is very good and allows web access. The problem is that the server is able to resolve DNS queries.

  How can I allow my server to resolve DNS again securely. I guess it's pretty simple to do, but I'm having a lot of trouble to find the solution.

  Thanks in advance

  Dylan

  On your IP set dns to 67.38.230.69, then ping www.yahoo.com server from guest... what resovle?

• new router = dns error after running over and over again, Network Diagnostics only a page appears, and then stops. tried to reset IE8 on XP tablet

  changed «sharing data...» ', looked already several answers... all other laptops (4) adapted for the new router & modem with no problems...

  When you run the network diagnostics I can connect to the internet once, but trying to follow the link or open the second window provides DNS error and kill the connection.
  last error now from network diagnostics is error 0x5b4 to query the server DNS 192.168.1.1; DNS not found, not a home user scenario...
  any other idea?

  Hello

  You did changes to the computer before the show?

  Please follow the steps mentioned in the link below.

  http://support.Microsoft.com/kb/314095

• There is an error with my computer, it does not connect with my router. It works with my usb 3g modem, but not with my router. My router works with other devices.

  There is an error with my computer, it does not connect with my router. It works with my usb 3g modem, but not with my router. My router works with other devices.
  I tried to connect my xbox to my computer to xbox live via the 3g router, but I was unable to. According to me, there is something wrong with the network card, since neither the wifi (wlan?) nor the lan connection seem to work.
  I harnessed connected my iPod, Xbox 360 and Nintendo DS for her, but not my computer. Please help me, what wrong with my computer?

  original title: problem with the map?

  Hi GustavTak,

  1. you have made no changes to the computer before the broadcast took place?
  2. do you get an error message?

  Try the steps from the following link:

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Additional information:
  Network connection problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Set up a wireless router
  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-wireless-router

• Updated ReadyNAS 316 OS, returned with the DNS error

  I've recently updated as well to my NAS 6.5.2 devices and since doing so, the VA started sending notifications, update attempts failed. When I investigated further, I discovered that none of the functions of the update seems to work. For example, when I click to search for updates to the NAS operating system rather than show 6.6.0 or tell me there is no update he insteads returns a DNS error. My network has not changed in any other respect. 2 devices still sync with eachother and all my users can still access their data in the two places for the more basic functions appear to be not affected. I have manually updated them to 6.6.0 OS but the OS DNS error update remains on this device. I noticed that at some point the AV definitions that update before the manual up-to-date operating system and now it seems to work (for the moment) very well. However, as I have already said, the error remains the update of the OS. Rather than report the status update I get a DNS error.

  Thoughts anyone?

  A friend today got the same problem after the update of the firmware.

  Try turning off IPv6 support on your network interfaces.

  It has resolved the issue.

• Reset my router & get a DNS error?

  Why do keep losing the connection to the internet and have too keep resetting my router & get a DNS error?

  Hello

   
  -What is the exact error message that you receive?
  -What is the operating system installed on your computer?
  -Did you do changes on the computer before this problem?
   
  Method 1: Run the network troubleshooter utility.
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7
   
  Method 2: Try to reset it TCP/IP and check.
  http://Windows.Microsoft.com/en-us/Windows7/change-TCP-IP-settings
   
  For reference:
  http://Windows.Microsoft.com/en-us/Windows7/DNS-domain-name-system-frequently-asked-questions
   
  Hope this information helps.

• "Gateway router not found" error when you try to connect the TiVO DVR with DLink router.

  Original title: gateway router not found

  try to connect the tivo series 2 to the internet with dlink router that he used to work with previous tivo but not with tivo now, it says gateway router not found
  However, my laptop works fine with the router, I tried tivo support nothing helps, too, if I use the phone line works of tivo, but do not store a lot and is running out of room so it will not work fo rme, helllpppppppp thanks

  Hello

  Where exactly you get this error message?

  See the troubleshooting suggested in "Network error message N07 or C107" steps from this link.

  If you try to connect the tivo series 2 to the internet with dlink router then check out the link below:

  http://support.TiVo.com/app/answers/detail/A_ID/400

  Please contact the manufacturer.

• Wired router with POE and Gigabit ethernet to run two AC1750 access points?

  Hello, I'm looking for a recommendation for a wired router with POE and Gigabit ethernet to connect to both access to ceiling LinkSys AC1750 points internet routing on the WAN to a Virgin Media UK cable connection plug - can someone advise a good solution?

  I'm a Home Office / Small Office so user there are several Wired's devices and a mixture of wireless clients. I need at least 8 ethernet outlets. Reliablity and speed performance are important, but not important enough to go overboard on the cost!

  Many thanks to you all.

  I recommend a router Linksys (SMB) LRT214\224 and a switch POE LGS Linksys (SMB). This combination will be very fast and stable.

• Wireless and wired router, DHCP and "visibility".

  Okay, it's a bit complicated, but I'll explain better than I can.

  I have a wired Linksys RV082 router. It works very well but is not wireless.  I have a Cisco/Linksys E2500 wireless router for my wireless devices to use.  the RV082 is the network of 192.168.1.x. The E2500 is the network of 192.168.0.x.  Cable Internet goes to the RV082 Wired, and a line out from there to the wireless router.  This all works fine except for a few disadvantages.

  I have an iPad that connects wireless and some of the apps offer a http:// option, so I can transfer files to this application.  I also have a network printer connected to wired and wireless devices do not.

  I have 2 problems:

  (1) in order to transfer files from my laptop (that I hung on the cable network most of the time), I disconnect the wire, wireless, then I can transfer files.  Œuvres, but it's embarrassing.

  (2) I want a netbook that I have on the wireless connection to print on my printer wired network.

  It seems that the 2 networks do not see each other.  Here are the things I've tried:

  (1) I disabled DHCP on the wireless router.  My thought is that requests for an IP address to the wireless router has sent will be transmitted along my wired router... NOT.  On my iPad and Wii, they could no longer connect wirelessly. Strangely enough, with the disconnected wire and wireless connection with my laptop, I've still was getting a 192.168.0.x IP address, even if the DHCP service is disabled on the wireless router.

  (2) thinking I would put manually the wireless router on the 192.168.1.x network, instead of saying things to get an Internet connection IP dynamicaly, I manually the IP value is 192.168.1.245.  Serious mistake.  I couldn't connect at all anywhere then.  The only way I could fix it was to hang on to my laptop computer, assign a static IP address to my laptop on the same network as the router, then I was able to get to the configuration page and to put things like he was.

  Another thing... Even when I'm connected only plugged on my laptop and wireless is disabled, I ping 192.168.0.1 (the wireless gateway) and it returns a value. But, when I try to go in a browser, I get a "page not found" error

  So, how can I get these two networks to play well and see each other?

  Thank you

  Jesse

  Put the router E2500 'bridge' mode and it will transmit the RV082.

  Assign E2500 DHCP, an IP address for itself of thje RV082, it will just be for access to the web administration E2500. System powered via the E2500 wired or wireless IP addresses will be obtained from the DHCP server on the RV082, and these will all be on the same subnet as designed to be plugged into the side of the RV082 LAN.

  Should allow you to do exactly what you want to do.

  I have a similar setup here works well with an E4200V2 right now.

• BEFSR41 wired router affected by change of modem cable

  Hi all

  You don't know if someone here can help me with a problem with the router above following a change of modem, I can get things to work, but once everything is turned off, the next time it starts things are back to how they were.

  To give a bit of history...

  My setup is a G4 Mac and a Xbox 360 Elite connected to a wired router BEFSR41, which in turn is connected to my cable modem, I am based in the United Kingdom so my ISP is Virgin Media.

  This configuration has been absolutely rock solid for more than 3 years, but last Sunday, I was unable to connect to internet and I noticed that the light on the modem was flashing instead of be constant, as it is supposed to be.

  I called Virgin and they did a test signal and confirm there is a problem and sent an engineer. He arrived Tuesday and confirmed the modem was very old and had packed and replaced by a new. We rebooted everything and everything was fine, I could email and get out on the internet as before.

  It worked fine the next day too but on Thursday morning, despite the fire loan being constant on the modem, I couldn't online again. I called Virgin and they did another test signal and said that something did not look right and they would send another engineer.

  He came Friday (different GUY), but confirmed that there is nothing wrong with the modem, the signal is OK just to verify, plugged the Mac directly into the modem, bypassing the router and I could get on the internet without problem.

  It seems that the router is at fault, but I have to say that it is a massive coincidence that it has stopped working correctly two days after the modem has been change, so I was looking at the configuration of the router via my browser page, and the only thing I did was to confirm under Type of Internet connection that "automatically an IP address to get" has been selected and I saved the settings and bingo everything works well again.

  So I put off, Mac, router and modem and switched back them and I'm at square one, no internet access. If I go to the router setup page again, "get automatically an IP address' is still selected and if I hit again 'save settings' everything works fine.

  I then started to bounce back each element separately and by turning the router or the mac on / off does not affect access, I am still able to get on the net, but as soon as I bounce the modem, I'm in the place again until I have click on 'save' on the router set up page.

  It's just my head in - what is the modem to the router to make it 'lose' its parameters and specifically, how to fix?

  I must say I don't remember when I bought the router through any complex installation, it is basically out of the box, go hooked upward and worked for 3 years and more.

  Any suggestions would be very welcome.

  Nick

  As far as I know, it seems that you have a cable modem.

  Your BEFSR41 should work with your modem when the BEFSR41 has been reset by default.  In addition, in some cases, you may need to 'clone' of the MAC address of the computer (the one that works when you connect it to the modem) in your BEFSR41.

  To reset your router by default, follow these steps:

  (1) turn off all computers, the router and the modem and disconnect from the wall.
  (2) disconnect all the wires of the router.
  (3) turn on the router and let it start up completely (1-2 minutes).
  (4) press in and hold the reset for 30 seconds button, then release it, then let the router reset and restart (2-3 minutes).
  (5) turn the router.
  (6) connect a computer cable to port 1 of the router (NOT to the internet port).
  (7) turn on the router and let it start up completely (1-2 minutes).
  (8) the power of the computer (if the computer has a wireless card, make sure it's off).
  (9) try ping on the router. To do this, click the 'Start' button > all programs > Accessories > command prompt. A black DOS window will appear. Enter the following text: "ping 192.168.1.1" (without the quotes) and press the Enter key. You will see 3 or 4 lines that begin with ' response to... ". "or"Request timed out". If you see "reply from...". ", your computer has found your router.
  (10) open your browser and point it to 192.168.1.1. This will take you to the login page of your router. Let the empty user name (Note: some routers have a username "admin") and in the password field, enter "admin" (without the quotes). This will take you to your router configuration page. Note the version number of your firmware (usually found near upper right corner of the screen).

  (11) If you need to clone the MAC address of your computer, do this step now.

  (12) If you get this far without problems, quit your browser and put your entire network.  Then, using an ethernet cable, connect the ethernet port of your modem to the Internet port on the BEFSR41.  Leave your computer connected to a LAN of the BEFSR41 ports.  If your modem has a USB port, do not connect anything to it.  If your modem works with a battery, remove it now, and then wait one minute, then replace the battery.  Turn on your modem and let it start up completely (1-5 minutes).  Turn on your BEFSR41 and let it start up completely (1-2 minutes).  Turn on your computer.  Try to connect to the Internet.  If you have a problem, temporarily disable your firewall software computer and try again to connect.  If you still have problems, see 'The replacement boot order' below.

  If you can not ' response to... ". "in step 9 above, your router is probably dead. A report with this problem

  If you get a response in step 9, but cannot complete step 10, is that your router is dead or the firmware is damaged. Related to this issue.

  If you need additional help, please give the results of steps 9 and 10. In addition, if you receive error messages, copy them exactly, and report.

  Please let me know how things turn out for you.

  Changing the boot order *.

  The boot order (modem, router, then computer) that I mentioned above is the classic boot order, and it works with most of the networks.  Some networks will work well if you turn on all devices at the same time.  However, the other networks is very picky about the way in which they are started, and they may also require a different boot order.  Sometimes, it can require a lot of experimenting until you find the boot order that works.  For example, I had once a system requiring that I start the router first, wait 5 minutes, and then start the modem and the computer.  Try different orders on your system until you find what works.

• Can not get on the net via wifi apt, dns error msg

  Howdy, hey i cant get on the net with any browser through my wifi apt. I can very well with any other wifi in the range but my wifi apt has the best signal. I get a msg of DNS server and tried everything that the computer recommended to fix. Why this only happen with wifi at my complex?

  SteveAustin71,
  Thank you for visiting the Microsoft Answers community forum.

  When you say that your wifi apt, it's your own personal network or provided by a complex of apartments for the residents?  Is that what you must pay for, or is it a free hot spot?  What is you get the exact error message?  If it's your personal network in your own apartment, what type of router is and is it secure?  If it is fixed, what kind of security it uses?  Answers to these questions will help us better diagnose your problem and propose solutions.

  DNS errors can mean different things, depending on what is the exact error message, but generally means that your computer does not have the DNS information from the router or server that is supposed to provide the IP address, gateway and DNS information on the computer when you log on.

  Let us know the answers to these questions so that we can better help you.
  Thank you

  Gloria
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Connection PS3 (DNS error)

  I cannot connect my ps3 to my Wireless Linksys WRT160N router. The router does not have a version type, so I guess it's version 1.0?

  Whenever I try to connect my ps3 I get a DNS error (80710102) of the playstation. I tried to use the automatic settings and manual settings. My laptop connects fine, but my PS3 doesn't even bother. During the settings auto, he will not even get an IP address, but when I entered this manually, it worked. However, I had no luck with typing manually DNS settings. It fails every time. Help, please!

  Thank you

  James

  First of all every time that you assign a static Ip address to your PS2, the IP address must be different from your computer, if you enter the same IP address, and then due to IP address conflict, it will make your Deivce work offline.

  Check the settings of your router wireless? It can be due to a higher level of security on your router. Connect to the router configuration page and click on the Wireless tab, and then click the sub-tab under wireless "Wireless Security" and below, change the Security Mode 'WPA discover' and under 'Passpharase' enter your password and click on save settings... "

  Now on your PS3, first remove the static IP address and then look for the wireless network and then trying to connect to it. Once connected to the wireless network your PS3 should be able to go online.

• WRT54G2 intermitened DNS error

  I have WRT54G2 router model linksys wierless but on even my Wired once per day or if I get an error when the router cannot connect to a DNS server and I lose the connection.  Bike sometimes the router works othertimes that it doesn't and I must circomvent the router to use internet that day.  any ideas?

  I had this problem but I put in some static dns servers and now its fine.

  serve your servers dns 8.8.8.8 and 8.8.4.4 (c/o of google: http://code.google.com/speed/public-dns/ )

• Windows 7 dns error

  I have a laptop that worked last Wednesday, 15/08/12 which will not have access to the internet.   It will connect to our home network and a Clearwire usb device I have but nor will provide internet access.  I have other laptops working find.  I emptied the dns, bought a new router, run netsh commands and tried a host of other tricks, including hardcode the Google DNS and Open DNS.

  The computer show it has been updated 19/08/12, which is the only thing that has changed.  This has been done with the automatic updates.  It is running Home Premium Service Pack 1 64-bit 7.

  I'm running out of ideas, any help would be appreciated.

  Update of Windows KB2705219 could be the cause and uninstall that solved the problem for some users.

  To uninstall an update - control panel, programs & features, [left side of the window] see installed updates. Wait until the system has finished the research for the list of updates. Select update required, then right click and Uninstall.

  But...

  See this notice - McAfee

  Some customers may experience a loss of network connectivity and/or errors in McAfee Security Center after a recent update

  You should make the fix McAfee, if necessary.

  I have McAfee, but the connection has started working again on its own so I thought I was clear of problems. However, when I checked it says he was doing routine checks the updates in vain when I told it to do a manually. So stick with McAfee without following their abduction - Reinstall procedure would have upgraded my PC at risk by not updated. Actually, I removed and then installed Microsoft Security Essentials rather & my answer IE is faster I knew it [even though I had the Add-ons McAfee disabled for centuries].

  I had to run the MCPRT deletion a few times before and it caused a problem with the license if the PC was not connected to the internet during the abduction. Due cat of McAfee support reset their files in order to allow the relocation-reactivation. Here is their link cat - McAfee - media contains the link to the cat

• Why am I messages DNS error since upgrading to El Capitan?

  Since I upgraded my OS to El Capitan I was making (Yahoo Search page) DNS error pages when I use an Internet link to leave my email to another site. Its pretty boring and I have to use Safari where it happens. I like FireFox, but if I can't solve this problem I will be forced to stop using it. Help, please. Thank you, Michael.

  You might have installed something more. On Mac, this problem is associated with some extensions Spigot, especially one named Searchme.

  Open the page modules using either:

  • CMD + SHIFT + a
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click Extensions. Then on the side right, remove or disable Searchme - and anything else that you don't need, like all the other Spigot/MyBrowserBar extensions. Keep in mind that all extensions are optional and none is included with Firefox when you get it first.

  Often, a link will appear above at least an extension disabled to restart Firefox. You can complete your work on the tab and click one of the links in the last step.

  Is that what helps you regain control?

  This could be the tip of an iceberg of malware. When you install free software, you often get the options grouped under silence. I don't know the best way to 'clean up' a Mac of these elements, but you may want to consider the issue.