Routing using Wireless LAN Controller

Similar Questions

• Cisco Wireless Lan Controller 2504

  Hello:

  Hello; I lost the password to my wireless LAN controller. Everything was fine until a few days ago and now can not identify.
  Is it possible to recover. The model of controller is AIR-CAP2602E-A-K9, the software version is 7.4.110.0.

  Please, anyone, help me.

  Kind regards.

  Fernando.

  Check this box:

  http://www.my80211.com/Cisco-WLC-CLI-commands/2009/12/27/recover-your-WL...

  Concerning

  Remember messages useful rates

• Are Cisco 1130ag APs compatible with Cisco Wireless LAN Controller virtual?

  Are Cisco 1130ag APs compatible with Cisco Wireless LAN Controller virtual?

  It's... AP compatibility depends on the code that runs on the WLC. This is a matrix that is a good reference.

  http://www.Cisco.com/en/us/docs/wireless/controller/5500/tech_notes/wire...

  Sent by Cisco Support technique iPhone App

• Equium L300 unable to connect to my router using wireless

  I have a laptop Equium L300 and can't connect to my router using the wireless option.

  I am told that the wireless feature is disabled on my pc but the switch on the front is activated.

  Can connect with the cable is the wireless.

  Anyone know what this could be?

  Try pressing Fn + F8, only the activated Wifi become?

  In Device Manager, the wireless device is reported to work ok?

  Try a BIOS update as well.

• Cannot use wireless LAN with my Satellite Pro A100

  Toshiba Satellite Pro A100-830
  NETGEAR DG834G

  Can not use the Wi - Fi connection. When you use "Free Config" to find peripheral wireless the popup "this connection is controlled by other software. I don't know what that means and what software controls the connection. I have other laptop which is duly connected by wireless. I'm ok with wired connection.

  I don't know much about the technical aspects and therefore ask for help so any reader can.
  Thank you
  Kris

  > Can't use the Wi - Fi connection. When you use "Free Config" to find peripheral wireless the popup "this connection is controlled by other software.

  You may not use the ConfigFree for configuring Wlan but own Vista configuration options or the WLan configuration tool like Atheros Clint Utility or Intel ProSet utility. It depends on the WLan card which utility can be used.
  Card Intel-> Intel ProSet utility; Card Atheros WLan-> Atheros Clint Utility

  I guess the message + this connection is controlled by other software + appears because one of the above options controls the WLan.

• Cisco 2112 and Apple TV Airplay wireless LAN Controller

  Hi all

  I'm having a problem with the help of iTunes, iPhones, and iPads on our wireless network. We have the WLC 2112 and 10 1142N WAP. If I do a network scan, I can see the Apple TV and port 5353 is open, which is Apple's morning service.  However, if I try to play the music/video on iTunes, or on an iPhone/iPad, I don't see the Airplay icon.  If I connect to the local network, the Airplay icon appears immediately. I created an allow all the rules in the ACL, but still no dice.  Any help would be greatly appreciated.

  THX

  Benm

  This Solution has been added in the following document

  https://supportforums.Cisco.com/docs/doc-21728

  If you have enabled IGMP snooping. To the title of controller, you have too many active multicast and multicast address?

• WebAuth LOCAL with Wireless Lan Controller and ISE

  Greetings,

  We intend to set up a centralised comments with sponsored webauth wireless network. I didn't know that this will not work with our current WLC code (6.0.199.4) as 7.2 or later version is required.

  We have a project to upgrade the WLCs but he won't be ready before the deadline for the completion of the reviews wireless.

  I am using local WebAuth temporarily until the WLCs are ready. My questions are:

  1. am I correct that I can still authenticate ISE?

  2. Since local webauth does not cost support, does that mean I can't apply a pre or post auth ACL?

  3. can someone point me to a good guide for configuring local webauth?

  Thank you!

  Hi Leroy,

  In CWA you can push the AVPs desire in the final result because of the nature of the flow:

  -Comments will connect to the SSID.

  -WLC send wireless MAB ask (1st authentication). In response, ISE returns accepted with url-redirect-acl and redirect url.

  -WLC updates the client session and once http (s) generated WLC redirects the customer to ISE according to AVPs received at the 1st auth(MAB request).

  -The customer enters the identification information in the portal. ISE valid creds and refers to WLC one type COA to re-authenticate.

  -WLC re authenticates the client (2nd authentication) session, and at this point ISE can support AVPs custom as names of VLANS, Interfaces or space air dynamic ACLs.

  -WLC overrides the client session with the new attributes.

  Local Web Auth as you mentioned, there are 2 steps but the WLC "considers" cela a single thread.

  To the LWA, the flow is as follows:

  -The client connects to the SSID.  Since there is no involved L2 auth client through DHCP, captures an IP and arrives at WebAuth_Required. Redirect URL is configured statically on WLC and pre auth ACL allows client access to ISE during the auth phase.

  -Customer opens the browser and WLC redirects the customer to ISE, but breast of redirection, there is a 'return to WLC' action which indicates to ISE to send customer WLC virtual IP containing identification information of the client used for auth in portal comments.

  -In this way the WLC now "knows" the handed creds to ISE and this way there is a formal request from RADIUS WLC sends to ISE asking these creds. ISE links in return an accept, and this is how the WLC now "knows" that auth is correct and she should move client to RUN.

  LOA of the simplest way would be to define an Interface of comments and statically applying a restrictive ACL at the level of the interface rather than wait the AVP of AAA server.

  LWA is supported in this version at very low level and basic, but if you want a complex flow involving the pusher of the dynamic attribute you will need something higher to 7.2.110.0.

  Recommended version would be 7.6.130.0 as for now.

  Kind regards

  Antonio

• Terms of wireless LAN Controller

  What is the purpose and reason for using virtual interface and port-management service, AP Manager?

  My bad... I mean WLC

  The Strip is telnet, ssh to the ip management. out of band is when the port has no real connection to your network. That is why the ip address of the service port is an ip address that is not part of your network shouldn't be routable in your network. In the case where your connection of loos to management and you do not know the commands for the cli, you can connect to the service port and use the GUI.

• Setting up autonomous HA - SKU Wireless Lan Controller

  Hello

  I ordered an AIR-CT5508-HA-K9. It is not match with WLC assets and there is no permanent AP license on this HA - SKU.

  I wonder if I can make any configuration or perform the software upgrade on the standalone HA - SKU?

  Thank you.

  You can do both, but you can use this HA - sku only for SINGLE sign-on or N + 1.  You can not use both as independent because you will get an error after 90 days.

  -Scott

  Evaluate the useful ticket *.

• wireless lan controller, allowing lag

  Hi all

  I used more than 47 ap on my 4402, and now he usually adds more, if I activate LAG happens with a WARNING saying it will delete all my interfaces, current - this true? or if I activate LAG it should still work as before?

  see you soon

  Carl,

  Activation of LAG does not remove interfaces.  So, if you activate the OFFSET and reboot, you should be fine.  Alternatively, you can configure another AP-Manager and bind it to the other port.

  See you soon,.
  Steve

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• M70 - 142:wireless - LAN doesn't work without AC ADAPTER.

  Hello
  My problem is a little trinkets.
  When my Toshiba works with AC ADAPTER and it uses wireless lan, network connection is very fast, good Internet downloads, but if I only use the battery, the transfer is very slow, internet pages download in a very long time and wireless network try blink icon rarely.
  So, to function normally again, I need to use AC ADAPTER again.
  I usually use a ZYXEL router for internet connection, I try with another without result and a different society also router. NOTHING
  Someone can help me.
  Thanx. Tony
  [email protected]

  Hi Tony,.

  I think that your problems are due to a utility that allows to get the maximum 'time place' battery of Toshiba power save. This is done by reducing power to some things that can drain the battery in their "full power" mode A common feature that most people notice, is that the screen is slightly lower under the power of the battery as the power supply. These energy savings are a feature and not a fault with the equipment, but the settings can be adjusted.

  Enter the menu in the Toshiba Utilities program start and open Power Options. You will notice that there are a number of profiles 'factory' that you can choose to give default settings for different configurations, including one for the battery power. All parameters can be set here.

  Once the settings have been changed, the wireless connection can run as fast as normal AC power, but the downside of this is that the battery may not last as long.

  I hope this helps, let us know how you go!

  Weezle

• Cisco NAC does support Wireless LAN?

  Hello

  I know that Cisco NAC support LAN wireless. I sent myself with various brands of autonomous APs. These work very well using the in-band, out-of-band mode.

  However, Cisco has been mentioned for Cisco AP, with Cisco switches and Cisco NAC, out-of-band is supported. I tried this today and it's or Cisco's fake, which is highly unlikely, or I have not configured the portion of the NAC or the access point Cisco correctly, which is most likely? I wonder where am I wrong? Please someone advice me on this?

  Kind regards

  RAM

  + 6012-2918870

  Hi Jean Claude,

  You can now do out-of-band with wireless deployments, but you must have a Wireless Lan Controller manage your APs. You can't do it with autonomous APs.

  The guide below will for most of the configuration:

  http://www.Cisco.com/en/us/products/ps6128/products_configuration_example09186a0080a138cc.shtml

  Thank you

  Nate

• Want to use internet to share WRV210 router between two LANs

  Hello

  I have the following scenario:

  A LAN has access to internet via ADSL through a Fortigate 50B (192.168.100.0)

  A new LAN (different segment) that should have access to the internet. (192.168.102.0)

  Two local networks need to have shared access resources among themselves.

  We have a WRV210 router between two LANs (192.168.100.0 WAN, 192.168.102.0 on LAN) configured in router mode.

  Resources work very well, but internet does not work.

  We receive answers internet addresses on 192.168.102.0 ping and tracert works very well, but we cannot navigate or connect to Skype, msn msg, etc..

  We made on fortigate 50B routes this way:

  192.168.102.0/255.255.255.0 192.168.100.102 internal

  192.168.100.102 is an address WAN WRV210

  We tried the gateway mode and internet works fine on 192.168.102.0, but 192.168.100.0 cannot contact 192.168.102.0 resources (obviously)

  What can be wrong in case of ping and tracert works very well, but nothing else works?

  Hi Willy,.

  You need the WRV210 in not the router mode gateway mode.

  Gateway mode active Stateful inspection, which will address translation from private to public IP addresses and NAT....

  "But I think that the VLAN on the router segments members to talk to other members on the other vlan, so your comment.

  Two local networks need to have shared access resources among themselves. "creates a problem.

  .

  A community previous publication says "with Port Based VLAN on the WRV210, there is no VLAN tagging and so on." It's more like say port 1 not to talk to port 2, because they are on separate physically designated VLAN (even if on the same subnet) and it is far as it goes. But with your configuration you want also to have the 2nd SSID do not talk to any wired client based on the RVS4000 as well? If so, this facility would not work because all wireless clients would be able to talk to cable customers and vice versa. But if you primary concern is simply to prevent the SSID 1 speaking with 2 SSID, it's doable in the page VLAN for the WRV210.

  So if you want the WRV210 to allow switching between the VLAN port basis, it won't work the way it is set up now...

  If you want to restrict access between IP hosts, I suggest using the list feature to access a managed switch that focuses on the PC or servers.  A switch may be as a series of 200 or 300 small businesses switch, see URL below...

  http://www.Cisco.com/en/us/products/ps10898/prod_models_comparison.html

  But then allow all ports to be a member of the VLAN by default.  I hope that I read your question correctly

  Best regards, Dave

• I have re installed the operating system on my Dell Studio 15 for Windows Vista 32-bit. But now the network controller is not working and I can't use wireless internet

  I have re installed the operating system on my Dell Studio 15 for Windows Vista 32-bit.  But now the network controller is not working and I can't use wireless internet, but I can plug a cable ethernet in there and get online.  What can I do?

  I have reinstalled the operating system on my Dell Studio 15 for Windows Vista 32-bit.  But now the network controller is not working and I can't use wireless internet, but I can plug a cable ethernet in there and get online.  What can I do?

  Install the appropriate network device drivers and software from the Dell downloads web site for your particular model, or better yet, tag Service...

• P1102w "unable to communicate with any wireless router using the provided SSID"

  Hi all, apologies if there is an answer to that somewhere, I took a look, and several people have had something similar, but without a clear resolution.

  I got a job p1102w successfully for about 2 years now and this week he suddenly won't print wireless. No recent changes to the network, no change to the printer, no changes to the computer.

  No luck with simple things so I reinstalled the printer (it works via USB), but when I get to the wireless network configuration steps I encountered a problem.  Automatically scan for wireless networks detects my home network, but by selecting translates "unable to communicate with any access point or wireless router using the provided SSID. The same error message occurs when you try to connect to a network wireless of my neighbors.

  Any ideas would be very appreciated.

  Isaac

  At this point, I would say that there is a problem with the card wireless in the printer.  Do you know if this printer is under warranty?

  www.HP.com/go/warrantycheck

  If your printer is still under warranty, then I suggest call HP for Technical Support on this printer.

  Contact HP worldwide | HP

  Jason