Terms of wireless LAN Controller

Similar Questions

• Routing using Wireless LAN Controller

  I was wondering if Wireless LAN controller (5508) can manage routing? This is our problem.

  We have a remote site, where we have bunch of 2900 series just pass. The router belongs and is managed by the provider of the PHONE company.

  We would like to install a controller (5508) and as the controller would make the delivery for the following subnets:

  The company 10.10.10.0/24 network

  Guest network 10.10.20.0/24

  Mobile (iPhone / iPad) 10.10.30.0/24

  Management Interface (AP) 10.10.40.0/24

  Is this possible? Or we need a layer 3 switch or a router that can do the routing for wireless controller.

  If possible, we prefer NOT to use the TELCO routing router subnet wireless?

  DS

  Unfortunately is the WLC a diverter. It is layer 2 only.

  Steve

  Sent by Cisco Support technique iPhone App

• Cisco Wireless Lan Controller 2504

  Hello:

  Hello; I lost the password to my wireless LAN controller. Everything was fine until a few days ago and now can not identify.
  Is it possible to recover. The model of controller is AIR-CAP2602E-A-K9, the software version is 7.4.110.0.

  Please, anyone, help me.

  Kind regards.

  Fernando.

  Check this box:

  http://www.my80211.com/Cisco-WLC-CLI-commands/2009/12/27/recover-your-WL...

  Concerning

  Remember messages useful rates

• Are Cisco 1130ag APs compatible with Cisco Wireless LAN Controller virtual?

  Are Cisco 1130ag APs compatible with Cisco Wireless LAN Controller virtual?

  It's... AP compatibility depends on the code that runs on the WLC. This is a matrix that is a good reference.

  http://www.Cisco.com/en/us/docs/wireless/controller/5500/tech_notes/wire...

  Sent by Cisco Support technique iPhone App

• Cisco 2112 and Apple TV Airplay wireless LAN Controller

  Hi all

  I'm having a problem with the help of iTunes, iPhones, and iPads on our wireless network. We have the WLC 2112 and 10 1142N WAP. If I do a network scan, I can see the Apple TV and port 5353 is open, which is Apple's morning service.  However, if I try to play the music/video on iTunes, or on an iPhone/iPad, I don't see the Airplay icon.  If I connect to the local network, the Airplay icon appears immediately. I created an allow all the rules in the ACL, but still no dice.  Any help would be greatly appreciated.

  THX

  Benm

  This Solution has been added in the following document

  https://supportforums.Cisco.com/docs/doc-21728

  If you have enabled IGMP snooping. To the title of controller, you have too many active multicast and multicast address?

• WebAuth LOCAL with Wireless Lan Controller and ISE

  Greetings,

  We intend to set up a centralised comments with sponsored webauth wireless network. I didn't know that this will not work with our current WLC code (6.0.199.4) as 7.2 or later version is required.

  We have a project to upgrade the WLCs but he won't be ready before the deadline for the completion of the reviews wireless.

  I am using local WebAuth temporarily until the WLCs are ready. My questions are:

  1. am I correct that I can still authenticate ISE?

  2. Since local webauth does not cost support, does that mean I can't apply a pre or post auth ACL?

  3. can someone point me to a good guide for configuring local webauth?

  Thank you!

  Hi Leroy,

  In CWA you can push the AVPs desire in the final result because of the nature of the flow:

  -Comments will connect to the SSID.

  -WLC send wireless MAB ask (1st authentication). In response, ISE returns accepted with url-redirect-acl and redirect url.

  -WLC updates the client session and once http (s) generated WLC redirects the customer to ISE according to AVPs received at the 1st auth(MAB request).

  -The customer enters the identification information in the portal. ISE valid creds and refers to WLC one type COA to re-authenticate.

  -WLC re authenticates the client (2nd authentication) session, and at this point ISE can support AVPs custom as names of VLANS, Interfaces or space air dynamic ACLs.

  -WLC overrides the client session with the new attributes.

  Local Web Auth as you mentioned, there are 2 steps but the WLC "considers" cela a single thread.

  To the LWA, the flow is as follows:

  -The client connects to the SSID.  Since there is no involved L2 auth client through DHCP, captures an IP and arrives at WebAuth_Required. Redirect URL is configured statically on WLC and pre auth ACL allows client access to ISE during the auth phase.

  -Customer opens the browser and WLC redirects the customer to ISE, but breast of redirection, there is a 'return to WLC' action which indicates to ISE to send customer WLC virtual IP containing identification information of the client used for auth in portal comments.

  -In this way the WLC now "knows" the handed creds to ISE and this way there is a formal request from RADIUS WLC sends to ISE asking these creds. ISE links in return an accept, and this is how the WLC now "knows" that auth is correct and she should move client to RUN.

  LOA of the simplest way would be to define an Interface of comments and statically applying a restrictive ACL at the level of the interface rather than wait the AVP of AAA server.

  LWA is supported in this version at very low level and basic, but if you want a complex flow involving the pusher of the dynamic attribute you will need something higher to 7.2.110.0.

  Recommended version would be 7.6.130.0 as for now.

  Kind regards

  Antonio

• Setting up autonomous HA - SKU Wireless Lan Controller

  Hello

  I ordered an AIR-CT5508-HA-K9. It is not match with WLC assets and there is no permanent AP license on this HA - SKU.

  I wonder if I can make any configuration or perform the software upgrade on the standalone HA - SKU?

  Thank you.

  You can do both, but you can use this HA - sku only for SINGLE sign-on or N + 1.  You can not use both as independent because you will get an error after 90 days.

  -Scott

  Evaluate the useful ticket *.

• wireless lan controller, allowing lag

  Hi all

  I used more than 47 ap on my 4402, and now he usually adds more, if I activate LAG happens with a WARNING saying it will delete all my interfaces, current - this true? or if I activate LAG it should still work as before?

  see you soon

  Carl,

  Activation of LAG does not remove interfaces.  So, if you activate the OFFSET and reboot, you should be fine.  Alternatively, you can configure another AP-Manager and bind it to the other port.

  See you soon,.
  Steve

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Cisco NAC does support Wireless LAN?

  Hello

  I know that Cisco NAC support LAN wireless. I sent myself with various brands of autonomous APs. These work very well using the in-band, out-of-band mode.

  However, Cisco has been mentioned for Cisco AP, with Cisco switches and Cisco NAC, out-of-band is supported. I tried this today and it's or Cisco's fake, which is highly unlikely, or I have not configured the portion of the NAC or the access point Cisco correctly, which is most likely? I wonder where am I wrong? Please someone advice me on this?

  Kind regards

  RAM

  + 6012-2918870

  Hi Jean Claude,

  You can now do out-of-band with wireless deployments, but you must have a Wireless Lan Controller manage your APs. You can't do it with autonomous APs.

  The guide below will for most of the configuration:

  http://www.Cisco.com/en/us/products/ps6128/products_configuration_example09186a0080a138cc.shtml

  Thank you

  Nate

• Integration of CISCO ISE with another controller wireless lan of the seller

  Hi all!

  I am currently working on an assignment and eager to integrate the identity service provider in the network. the only problem is that the deployed wireless network earlier of another provider I just need to know that either ISE has integration with the other controller feature wireless provider and can provide guest access control. The LDAP integration is also required.

  Waiting for help!

  Hello

  According to my knowledge Yes, Cisco ISE can be integrated with another controller wireless LAN of the seller, but limited. (Aruba, Rukus) and if you want to add the external identity group to your network, then LDAP integration is required.

• 20 - r011il: driver for windows 8 64-bit wireless lan

  bcm43142a0 I am not able to find some drivers... "" - i.e. the driver wireless lan.

  and the other is... "network controller".

  He "Alwayse" said a problem of compatibility with this device.  I use windows 8 64-bit os.

  Please suggest any driver as soon as possible

  Hello:

  There is no drivers windows 8 for the model Broadcom wireless network adapter that has your laptop.

  I suggest that you connect through an ethernet cable, required for W8, so that you can ge updates free update for the Windows store W8.1, and then use the drivers your PC support page W8.1.

• Satellite U940 - update Realtek Wireless LAN Driver

  I just upgraded my Satellite U940 PSU6VA - 00S 002 Windows 8 to 8.1 of Windows and am currently following the instructions of the upgrade from here. I noticed that European and Australian Toshiba sites include a 'Realtek Wireless LAN Driver' in their list of downloads driver for Windows 8.1 for the Satellite U940:
  - European page
  -[http://support.toshiba-tie.co.jp/windows81/drivers/PSU6V_Up_au.htm]

  However, I have never noticed any a Realtek wireless LAN driver on my computer, before even that I have upgraded to Windows 8.1. I've only seen in Device Manager network cards:
  -Intel Centrino Wireless-N 2200
  -Realtek PCIe FE Family Controller (which I believe is a wired LAN driver, not a LAN wireless driver).

  So my question is: do I have to download the Realtek wireless network driver or is it not suitable for my system?

  > So my question is: do I have to download the Realtek wireless network driver or is it not suitable for my system?

  Your laptop was equipped with Intel wireless network adapter and NOT card Realtek WLan and therefore the Realtek WLan driver does not need to be installed.
  You should consider a fact: there are different laptops on the market models that are equipped with different material parts. Some support the Realtek WLan card and some models were equipped with modules WLan Intel and that's why you can find some drivers (like Realtek Bluetooth Driver Package Filter) in the driver from the list of downloads that are not essential for all models.

• Equium U400-145: Wireless LAN cannot be disabled

  Hello

  I can't turn off the LAN wireless with the switch or the Fn + F8 key. Although both are the indicator wireless LAN off (light in the front of the machine) the wireless LAN remains active.

  I tried to reinstall WLAN Driver and installed the last package of added value.

  Here is some detail on what I installed.

  Model name Satellite U400
  Version of the OS Microsoft Windows 7 Home Premium 6.1.7600
  Version of the BIOS V4.00
  Processor Intel (r) Pentium (r) Dual CPU T2390 1.86 GHz
  Physical memory 2048 MB RAM
  Network Marvell Yukon 88E8040T PCI - E Fast Ethernet Controller = 11.0.5.3 version = 00:1E:68:61:E4:8F MAC address
  Realtek RTL8187B Wireless 802. 11b / g 54Mbps USB 2.0 Network Adapter = 62.1181.1105.2009 version = 00:16:44:F1:54:92 MAC address

  Thank you.

  Hello

  This seems odd, that if you can not turn it off with the wlan switch, it may be a malfunction of the equipment. Have you tried to restore factory settings? Please, do it. If she doesn't fix it, there is hardware problem. I have never met such problems.

• Satellite M30: Impossible to install a wireless LAN

  Hello

  I have a Toshiba Satellite M30, with Windows Xp. I can't install a wireless LAN, and I think that the cause is that I don't have the driver for:
  In Intel (r) 82801DBM LPC Interface Controller - 24CC

  I can not found in the web page.
  Please can some body tell me where to find

  Thank you

  Hello

  Please check this Toshiba driver download page:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

  You'll find maps, Atheros and Intel WLan drivers for Windows 2000 and Win Xp.

  Good bye

• Question of Wireless Lan L410 (0616-A18)

  Hi all

  I used my cell phone for more than two years with ZERO complaints, until my hard drive died a few days ago

  I bought a new Intel SSD and installed a fresh copy of Windows 7

  I'm having a strange problem which is that I'm not able to install the drivers for the wireless LAN card, I am sure that I have the realtek one and I used on my previous installation realtek driver and it worked perfectly, now I find three types of Intel drivers and a Thinkpad driver, none of them moved correctly map

  the map appears in Device Manager under other devices as a "network controller".

  is it possible to know the exact model of the card to get his driver on the manufacturer's Web site? or any other suggestions?

  Thanks in advance

  Solved using the driver below

  Thank YOU for guiding me to this page on the realtek website

  I tried until this one worked under XP and 7

  RTL8192CE-VA4
  latest version: 1005.43.0913.2012