RV082 SB + switches with functionality of tag vlan

Similar Questions

• With the help of VLANS and VLAN Tagging is not working / no connection

  Hello

  I m trying to configure a VLAN between some virtual machines on ESX host 3.

  I want to do this way:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1004074

  I got 1 dedicated NETWORK adapter to each ESX host that is connected to a dvSwitch in which I configured a portgroup

  with VLAN ID 2121. I have configured each virtual machine to use this network.

  When I put the virtual machines on a single host, they are able to communicate.

  When they are placed on different hosts they are (if the VIRTUAL LAN is enabled on portgroup) not able to communicate.

  So I m assuming it must be a problem in the config NIC on the ESX host or switch.

  I m using a HP2910AL on which I activated mode trunk for each port that is connected to a NETWORK card with

  the dvSwitch/Portgroup I try to use for the vlan. In the hp switch, I have a default VLAN with ID 1 where

  the Ports are marked not signposted. I install a second VLAN on the switch with ID 2121 in which I scored

  This tag ports.

  Is there something else to do - perhaps side ESX host?

  I tried changing the settings as "forged transmission-> allow ' on portgroup and I found other things

  in the web, but always without success.

  Kind regards

  Patrick

  Were you referred to this guide? :

  http://CDN.ProCurve.com/training/manuals/2910-ATG-Feb09-2-VLAN.PDF

  "show vlan ports" would be my next check to make sure that you have connected to your ESXi host 3 ports in the vlan 2121.

  As Duncan has said if you have a VLAN ID on the portgroup in the vSwitch and you have the port on the pSwitch as trunk not acess and VLAN ID is allowed on the trunk port pSwitch you should be ok.  Just to clarify the trunk is 802. 1 q No 802.3ad.

  The reverse is not VLAN ID on the portgroup vSwitch, use coelio on pSwitch with VLAN ID.  Limited pSwitch port to a VLAN, this may be ok for you?

• VMware Distributed Switch with VLAN

  Hi again,

  A lot of work with VLAN now.

  But just a quick Questions. Is there a documentation or HowTo Guides how to set up vSphare VMware Distributed Switch with several VLANS on a Switch GS724Tv4?

  

  But soon, I try to add a host or network, it is empty.

  This is probably an easy problem of VMware, but I try here first to see if someone has document guide HowTo so I can start with.

  Thank you

  Christian

  Never mind about this,

  I found the problem on my own, but perhaps a documentation would be great to have. But it's a good start to have the right license of VMware, before you start.

  * I was just out of luck when I thought *.

  / Christian

• Fortinet virtual with tagging VLAN

  Hi all

  in fact I do tests with the appliance of virtual firewall from Fortinet. These device have 10 virtual NIC

  The Fortinet vm can manage the VLAN different on a single port "physical."

  How can I set more than one VLAN on a Port, VM-is it possible?

  Objective:

  -A virtual firewall to several VLANS

  -VM-customers with different VM Server VLAN different.

  I hope someone have some experience with vm-Fortinet a VMWare

  Roger

  Hi Roger,

  It is indeed very easy to achieve. We have many implementations of similar to this:

  1. create a GROUP of ports on your vSwitch or dvSwitch Called "Fortinet Trunk" or something similar

  2 change the PortGroup and change the VLAN to "VLAN Trunking", in the "VLAN Trunk Range" field enter all them VLAN, you will need

  3. on your Fortinet device assign one of the interfaces to the "trunk Fortinet"

  4. on the interfaces under Setup of Fortinet for each virtual local area network

  5 create a new Port Group for each VIRTUAL local area network, modify the PortGroup to include the VLAN ID (your virtual machines will sit on it)

  This should be everything you need to get this up and running, any questions or problems please let me know. I can help more if necessary.

  Concerning

  Steve

• What are the bare minimum commands to get a stack of PC6825 3 - switch with inter switch Link Aggregation?

  I am brand new to PowerConnect switches, even though I am familiar with the concepts of VLANS, aggregation of links and spanning tree.

  I am on a deadline to get some new ones installed 6248 in our baskets and get them functioning as a stack. What are the bare minimum commands for:

  • Three switches in a stack (master/Eve/member)
  • 2 ports grouped between each (total redundancy) switch with loops WITHOUT switching

  All the switches are running firmware v3.3.9.1 (January 2014).

  Thank you

  The range of interface Ethernet 1/g1-1 / g2 allows you to select the ports you want in the channel of the port. Page 293

  Channel-group 1 Auto mode to create 440 lacp lag page

  Select the Group of channels with interface port-channel 1

  Switchport page 601 in trunk mode

  Switchport trunk allowed vlan [VLAN you use]

  http://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_powerconnect/PowerConnect-6248_Reference%20Guide_en-us.PDF

• With the help of Vlan for LAN and DMZ

  Hello

  For the moment, I have assigned my LAN and DMZ networks to two separate network card (so therefore no Vlan tagging)

  for example vmnic0 = LAN, vmnic1 = DMZ.

  It works well but I like to make changes in the way I want to use two separate physical network adapter and use on the two s two LAN and DMZ nic but now using the VLAN.

  So think of this configuration:

  For each network, I create a Vswitch, in order to obtain a Vswitch named VsLAN, VsDMZ for the case.

  The Vswitch I attribute a two nic Nic will be the day before. as vmnic0, vmnic2 (at rest)

  This Vswitch I create a port group and assign the correct number of VLan as LAN 10 and 20 to the DMZ.

  Create the another Vswitch will have the same Nic but now vmnic0 will be the stanby one.

  Probalby all great so far I think or not?

  Issues related to the:

  -Well this concept where there is a relationship a Vswitch and port group or a switch with multiple exchanges?

  In case a Vswitch with multiple port groups I will assign to group level reserve and the active NIC Port.

  -If I create a group of ports and assiging several Vlan IP packets received by the virtual machine itself also be labelled or not identified?

  Other words. Do I need to configure the NETWORK adapter to the virtual machine also for the same local network ID virtual or not.

  Thanks for your comments.

  Hello

  Change of vlan is a pretty good idea to get the failover and the performance of the network LAN and DMZ. You have confused somewhat however concepts.

  A can only be used in a vSwitch vmnic. So what you want to do is the following:

  Create a vSwitch

  On the vSwitch create two ports: LAN (vlan10), DMZ (vlan20)

  If vmnic0 and vmnic1 have access to the vlan10 and 20, then simply add the two vmnic virtual switch. By default, they will both be active and that's fine. If you do not want to CHANGE the GRPE ports LAN and goto the "failover" tab and put vmnic0 as active and vmnic1 as before. Then do the reverse on the DMZ port group.

  Best regards

  Frank Brix Pedersen

  blog: http://www.vfrank.org

• Problem of tagging VLAN

  I did some research on "best practices" networking and decided to test it on a cluster.

  (1) I have a group of ports vmotion the tag with a tag VLAN 30 on 2 ESX hosts

  (2) the port vmotion group is on its own subnet separate from anything else (10.0.2.0/24)

  (3) in the interfaces of contactors (Dell Powerconnect 6248) I'm going to ' linking IP subnet of VLAN "and link the VLAN 30 to 10.0.2.0/24

  I then try a vmotion, and it fails to 10%, most likely a problem with the network as guests are defined in/etc/hosts and times are synchronized.

  So, I delete the vlan tags, remove the link in step 3, and voila, vmotion work once more!

  Someone has any advice here to share on what went wrong? Perhaps more important still actually do I have a tag of vlan? Since the vmotion vmkernel is in his own vswitch and separate subnet, it seems that traffic is already entirely separate...

  (3) in the interfaces of contactors (Dell Powerconnect 6248) I'm going to ' linking IP subnet of VLAN "and link the VLAN 30 to 10.0.2.0/24

  You have a dedicated NETWORK card (or NIC) only for the VMotions?

  You will need to tag the switch port (or put it in the trunk and activate the VLAN30).

  At this point, do not use bind IP (is just to prevent impersonation).

  Try first to set the correct port - belonging to a VLAN.

  Also a vmkping between the two ports of VMotion could be useful for diagnosis.

  André

  * If you found this device or any other answer useful please consider awarding points for correct or helpful answers

• The photo with searchable keywords tagging?

  Why is there no way to tag with keywords searchable photos? I have 37 000 + photos and none of them does not when I'm looking for them.

  I use various applications and sometimes I know I have the perfect picture to post/share/reference in mind and cannot, for the life of me, find it. In addition, some applications will choke when dealing with my scroll so many photos.

  "Faces" is fine, but I cannot find the "perfect willow tree' or"1949 Mercury hotrod"photo, that I took years.

  Please Apple - add a function for 'tag' my own pictures in my photo album so that I can search and find relevant pictures.

  Why nobody has thought of this? I will gladly accept a fee of 1 cent for each used tag and we'll call it square.

  Thank you

  OrangeBeard

  Supports photos keywords and keyword search. Are these functions doesn't work is not for you, or you just knew about them?

  To add keywords: https://help.apple.com/photos/mac/1.0/?lang=en#/phta4e5a733f

  To perform a keyword search: https://help.apple.com/photos/mac/1.0/?lang=en#/pht8d0ad5198

• Button as a switch with logic gates.

  Hello, I am a student using LabVIEW 2012 as a FRC competitor, and I have a question/request to anyone who wants to.

  I can't find a non-buggy solution to get a button to work exactly like a switch. Either the solution train, or doesn't connect.

  I tried D type Flip Flop of all kinds, and! Q can not connect to D in LabVIEW (LabVIEW pulls the errors of "more than one data source", so a lot of logic functions that is available with other solutions, do not work on LabVIEW)

  NAND gate-types have been so tried, no dice.

  So if someone would like to help me, that's what I'm looking for:

  When the button is clicked, it sends a real constant function until the button is clicked again.

  -I can't use anything that messes with functions if the button is pressed.

  -J' I just need a simple on/off switch, nothing that goes 'around' from what currently exists and actually a buggy solution. It should be a kind of good way to do it.

  -An attachment of a VI would be nice, and what goes where.

  Thank you

  
  

• My Ipad air2 does not start.  Tried hold it together switch with on/off switch.  Apple logo appears for about 15 seconds and then turns off again.

  My Ipad air2 does not start.  Tried hold it together switch with on/off switch.  Apple logo appears for about 15 seconds and then turns off again.

  Is there another way to start the IPAD?

  Try the steps here:

  https://support.Apple.com/en-us/HT201412

• Satellite S50T-B950 - can't dim / brighten screen with function key

  Hello

  So, I can't decrease or brighten my screen with function key. Although things like the volume and function key still works.

  Someone at - it suggestions that I could try? I can't see all the options on how to resolve this problem within the program of 5500 intel HD or in my AMD catalyst thing.

  Anyone ever had this before or have a fix for this?

  Thank you

  Can you please tell us which model of laptop and operating system do you use?
  Are you using the original operating system that you got with your machine or you have installed the clean version?

  Did you remove something from your system?

• Installed new microcomputer, LibreOffice, but the "open with" function does not recognize it

  I recently downloaded suite desktop LibreOffice, but OPEN WITH function recognizes not all programs.  How can I fix it?

  Contact support LibreOffice.

• Configure BEFSR41 V.2.1. to use as switch with ADSL ZTE Modem in Bridged mode

  I found a thread of 2009 who has a link that could help me with this configuration, but the link does not work.

  I have a Linksys BEFSR41 V.2.1 and need to set it up, so I can use it as a switch with our ZTE 831 ADSL Modem, which is in bridged Mode.

  The IP address of the BEFSR41 changed to avoid a conflict with the address IP of Modem ZTE ADSL, which is 192.168.1.1 to 192.168.2.1.

  If the PC is connected directly to the ZTE ADSL Modem, I can access the Internet and I can access the Menu of Configuration of Modem ZTE.

  If the PC is directly connected to the Linksys BEFSR41, I can access the Menu of Configuration Linksys.

  If the PC is connected to the Linksys BEFSR41, and which is connected to the ZTE ADSL Modem, I can't access the Internet, and I cannot Ping the ZTE ADSL Modem.

  Please give me a URL that indicates how the Linksys BEFSR41 should be configured to use as a switch with my ADSL Modem from ZTE in bridged Mode.

  My belief is that after I have the Linksys set up, I then plug the ZTE ADSL modem in the Linksys unit and use it to DHCP.

  DRM for your time and help! Lanny

  1. I never told of any change on the Advanced Routing page.

  2 do not connect the internet port for ZTE with this kind of configuration. You cannot use the internet port.

  3. Once you set that you can use the remaining LAN for ethernet devices ports in your local network.

• N3048 tagging VLAN

  Just recently, we bought a n3048 to replace our PowerConnect 6248 failure. The section belonging to a VLAN on the 6248 allows to tag the ports for VLAN specific in four States. An empty box for unconfigured, U for unidentified, T for the tag and F I believe is forbidden. The n3048 has only two States: white and U. Can someone explain how to have a law on the port in the same way it would on the 6248 has been T tag?

  You need to set the port in general or Trunk mode settings in order to Tag VLAN. Page 663 user guide begins detailing options and how they are defined.

  http://Dell.to/1wlbEn2

  See you soon

• VLAN Tag vlan vs unidentified

  I am running Dell Power Connect 5548 and 5524 in an arrangement of battery on 3 floors.

  I have a question on the Middle floor by which DHCP addresses are not to be issued to clients in vlan 90

  See below

  GFLOOR

  interface gigabitethernet1/0/48
  channel-group mode 1 on
  switchport mode general
  switchport general allowed vlan add 40,50,70,80,90 tag
  VLAN allowed switchport General add 1 unidentified

  interface gigabitethernet2/0/48
  channel-group mode 1 on
  switchport mode general
  switchport general allowed vlan add 40,50,70,80,90 tag
  VLAN allowed switchport General add 1 unidentified
  !
  Interface Port - Channel 1
  Description LAG_TO_TOP_FLOOR
  switchport mode general
  switchport general allowed vlan add 40,50,70,80,90 tag
  VLAN allowed switchport General add 1 unidentified

  1FLOOR

  interface gigabitethernet1/0/48
  channel-group mode 1 on
  switchport mode general
  switchport general allowed vlan add 40,50,70,80 tag
  VLAN allowed switchport General add 1.90 untagged

  interface gigabitethernet2/0/48
  channel-group mode 1 on
  switchport mode general
  switchport general allowed vlan add 40,50,70,80 tag
  VLAN allowed switchport General add 1.90 untagged

  interface gigabitethernet3/0/24
  switchport access vlan 50
  Interface Port - Channel 1
  Description LAG_TO_TOP_FLOOR
  switchport mode general
  switchport general allowed vlan add 40,50,70,80 tag
  VLAN allowed switchport General add 1.90 untagged

  I just need to tap 1Floor interfaces or should I take 90 off unmarked first, then add to marked subsequently

  switchport mode general
  switchport general allowed vlan add 40,50,70,80,90 tag
  VLAN allowed switchport General add 1 unidentified

  Thank you

  ANDY

  If that's the difference and the other works and the other is not then I suggest matching the configs on the floors.

  Is there a reason why, the floors are set up differently?