RV220W - multiple public IP addresses
All, morning
I am setting up this new router from a client. I'm running on a question that I can't make it work. I was wondering if anyone would be able to help. They use IP addresses public 5. Currently the wan port on the router est.66 and I have all ports forwarded to the correct internal IP. It works very well. However, I need parts before else public IP (e.g. internal:.67) to IP address So far, I was able to achieve through the TAR one-to-one feature. It allows me to forward a port from a public IP address to a private IP address. However, I need to redirect ports 3 or 4 by public IP address to one address only internal. Anyone know what I'm doing wrong here? This router does not support this feature?
Thank you
David Rhea
Hello David,.
How weird to put in place... but the nat from one to the other is the first step that you do. Once you transfer a port using nat one by one, and then you create an access rule. Create an ACL rule allowing traffic between wan and lan, what service/port you transfer, always allowm, fix ip source, destination ip, it's that you transfer the port too you would change the destination of the internet to others and then you should be able to fill the void of what another public address you are wanting to use. The test blank must be labelled internet destination ip:.
I hope that helps you out.
Thank you
Clayton Sill
Tags: Cisco Support
Similar Questions
-
The router RSV4000 does support multiple public IP addresses
I have a client who has a RSV4000 router. The customer also bought a block of 5 usable public IP addresses. I need to be able to assign these public IP addresses for printers, either by configuring a static IP address on each printer directly or through mapping of intellectual property or any other method. Made support for RSV4000 using several treats public IP and if so what configuration is required in the router for printers to be seen by the outside world.
Hi Winston,
Thank you for posting. The functionality you need is one-to-one NAT, who does not have the RVS4000. Please watch the RV042 or RV220W for this feature.
-
What are the causes an IP internal to "attack" multiple public IP addresses?
We had to many TCP SYN host sweep. Could someone share what could cause the above? Follow copies of the alert details.
evIdsAlert: eventId = 1216742775473866070 = severity = informational Cisco vendor
Author:
hostId: ips
appName: sensorApp
appInstanceId: 403
time: August 8, 2008 19:18:53 UTC offset = 480 timeZone = GMT-08:00
signature: description = TCP SYN host Sweep id = 3030 = S2 version
subsigId: 0
marsCategory: probe/SpecificPorts
interfaceGroup: vs0
VLAN: 0
participants:
striker:
addr: 172.16.5.111 locality = OUT
Port: 3958
target:
addr: 69.63.178.11 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 64.62.193.70 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 77.67.127.41 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 64.215.162.27 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 65.55.15.242 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 77.67.127.10 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 69.63.176.167 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 65.242.27.32 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 64.209.118.140 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 77.67.127.25 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 207.200.64.225 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 207.68.179.219 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 65.55.13.158 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 63.217.8.128 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 66.151.244.212 locality = OUT
OS: idSource = unknown type = unknown = relevant
target:
addr: 207.200.64.161 locality = OUT
OS: idSource = unknown type = unknown = relevant
alertDetails: InterfaceAttributes: = 'Unknown' physical context = 'Unknown' bottom of basket = "GigabitEthernet0/1 ';
riskRatingValue: 31 targetValueRating = average attackRelevanceRating = relevant
threatRatingValue: 31
Interface: GigabitEthernet0/1 context unknown physical = unknown = backplane = GigabitEthernet0/1
Protocol: tcp
Scans when detected on the network local are "mostly" false positives, that's the official word from Cisco:
"Benign triggers.
Scan host 3030 and 3032 signatures detect behaviors that cannot be observed from sources outside the local network, but are normal behaviors for sources within the local network. »
You can filter these signatures of the LAN hosts using event Action filters or tune the signature (using the source / dest. fields inside).
Concerning
Farrukh
-
RV220W - rules of access/redirection of port with multiple WAN IP addresses
I just installed a Cisco RV220W - that works very well for outbound traffic, however for incoming it seems unable to work with multiple WAN IP addresses.
We have a block of 6 WAN IPs assigned to us by our ISP, and I want to use each of them to expose certain ports on our servers to the outside world.
I tried to do with rules (by using HTTP, for example) with the following parameters:
Connection type: Inbound (WAN (Internet) > LAN (local area network))
Action: Always leave
Service: HTTP
Source IP: Unique address
Start:
Send to the Server Local (DNAT IP):
Use other WAN (Internet) IP address: disabled
Status: Activated
However, the port of the inaccessible Server/rest.
I tried:
- Restart the server with power power off again
- implement the same port forwarding settings
- triple-checking all the IP addresses used
The only way that I have working is by changing the access rule so that it applies to any specific source rather than to another address... but this isn't a solution for us because we need to use specific IP addresses to the internal servers/ports specific.
The interface of the router admin certainly suggests that this should be possible, but using it seems to break all incoming access!
Any suggestion is welcome.
You must use "ANY" as the source IP address, you publish your internal server to the internet and the internet means that the request comes from any source IP address (you don't know what it is, so that's all.
Basically, you want any source IP to hit one of your WAN IP on port 80, and then your firewall will redirect the request to the internal private IP address of the server on the same port 80. And when the answer comes back internal server, the firewall will already have this translate entry in and reverse NAT won't happen (you must configure it, the default firewall function).
I hope that I have answered your question.
Please mark as correct, if you like the answer.
Thank you
-
Public IP address used internally on RV220W
Hello
I've finally set up our RV220W to serve our network of offices, using the following environment:
WAN is set for a public IP (static configuration), while internal network consists of two VLANS.
VLAN 1 is connected to the cable network and a SSID wireless, where DHCP is served by our server Windows SBS (192.168.15.x), and this VLAN is used only for our own office. VLAN 2 is connected to a second SSID wireless, where DHCP is served by the RV220W himself (192.168.17.x) and this VLAN is used for guests and visitors to our office.
On a regular basis, we need to use a mobile device to access a test page of a development server on VLAN 1, and the router is configured to redirect the connections on a specific port on the public IP address to our development server.
For VLAN 1, I solved this by substituting the DNS for the host name of this test page to use the local IP address of the development server.
However, for VLAN 2, there is no way to access this test page.
Is there a way I can configure the router to redirect connections, either replace the internal DNS for the test on the development server page is also accessible from 2 VLAN (network comments/visitor)?
Thanks for any help.
Hi Kim, what firmware version are you using? You can load the last
On older versions, there are a few problems Hairpin, but most have been resolved on the latest 2 releases.
-Tom
Please evaluate the useful messages -
I can map a public IP address on a pc using the router tplink?
I can map a public IP address on a pc using the router tplink?
Moved from the community involvement Center
Original title: Port forwading
Check with the support of tplink.
-
Access to the COR to two XP systems behind a router with a single public IP address
Hello
is it possible to access the RDC to two XP systems, with two different port for the DRC, behind a router with a single public IP address?
Please note this ia a small home network without any parameters of the field. I use IP to access DRC.
You comments are appreciated.
Thank you
Use different ports for the DRC on both XP and configure the router to redirect to the appropriate port on the appropriate computer.
See the article in the Microsoft Knowledge Base How to change the listening port for remote desktop .
-
X 2000 and multiple static IP addresses
Hello
I have a X 2000 router which is connected to a DSL cable.
My DSL contract have 16 static IP addresses.
In order to make this work I had to choose PPPoA with my user name and password.
The router automatically got my IP address and I can go on the internet.
Now, I need to map one of my other IP addresses to a server inside my local network.
How can I do a NAT between (for example) port 80 on my another static IP address to one of my LAN IP?
Thank you
Max
The X 2000 is a consumer. It supports only a single public IP address.
-
Hi I have a V2 E4200 and it is updated to firmware Linksys Wifi Smart... Is it possible to block a public IP address?
# It is not so smart than that.
You would need a real firewall.
-
Hello
I have a service online Internet with 5 public IP addresses.
The router and the AP are connected to a switch.
I would like to set up a WRT54G Router with a public IP address and use DHCP (with private ip address) for the computers that will connect to the AP.
That the AP is connected to the switch, it is possible that the other wired computers that are connected to the same switch can get an IP from the DHCP?
Thanks in advance
In this case, the routing is automatic.
WRT54G configuration:
WAN:
Internet connection: static IP address
IP address: 180.X. X 170
Subnet mask: 255.255.255.248
Gateway: 180.x.x.x (Ex: 180.x.x.1)
DNS: servers your ISP DNS
LAN:
The IP address of the router: 10.10.10.1
DHCP range: 10.10.10.100 of-online 10.10.10.200
-
Deployment of ESA without public IP address
Hello Experts,
I want to know that if I deploy ESA in my network without public IP address with a config on the SAA as if is there any traffic to port 25, then transmits to the ESA to the Exchange.
I published the public IP address of my firewall in the MX record.
In this scenario, there will be no problem for the ESA to determine the reputation of the sender when you receive an email?
And if ESA is not able to determine the reputation of the sender, then, what is the best way to deploy the ESA without using a public IP address.
I know that 99% of the ESA facilities use a private IP address on the public static listener with NAT on the firewall in front of the ESA. There is nothing wrong with that. Just think that get translated here. This is the destination IP address of the request that comes from the internet and ESA can still see the IP address of the sender. Only your internal mail server does not see the sender-original INVESTIGATION period. But there's nothing in general not as SPAM-check is done, when the mail strikes the internal server.
-
Hi, we just got router ISR4331. We will use this router to our datacenter as pummel hub. Not to mention that it will be the static IP address. Our goal is to connect 30 small offices to the Datacenter by VPN site-to-site. All of our offices a RV042 router and DSL connection, so dynamic public IP. How to accomplish this task. Before the VPN connection is stable and the need not to configure tunnels frequently.
Thank you
GM
Hello
Please check the config below:
HUBS:
crypto ISAKMP policy 1
BA 3desmd5 hashpreshared authenticationGroup 2life 86400crypto isakmp secretkey key address 0.0.0.0 0.0.0.0 (Having said that the dynamic router HUB remote routers have public ip address)Describe your valuable traffic. Note that I have sepcified for both tunnels, but basically, it will be the same for the rest out for the destination. For example, I used 192.168.1.0/24 and 192.168.2.0/24. You will need to replace it with your existing installation.TUN1 extended IP access listip permit 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255TUN2 extended IP access listip permit 192.168.1.0 0.0.0.255 192.168.3.0 0.0.0.255Create your strategy to Phase 2Crypto ipsec transform-set esp-3des esp-md5-hmac TScard crypto S2STUN 1-isakmp dynamic ipsec HUB_TUNcrypto dynamic-map HUB_TUN 1086400 seconds, life of security association setgame of transformation-TSmatch address TUN1!crypto dynamic-map HUB_TUN 1186400 seconds, life of security association setgame of transformation-TSmatch address TUN2Now apply the card encryption to your WAN interfacegi0/1 interfacecard crypto S2STUNNow configure on your remote routersRemote router 1crypto ISAKMP policy 1
BA 3desmd5 hashpreshared authenticationGroup 2life 86400!ISAKMP crypto secretkey key address x.x.x.x (replace with your public ip address of the HUB)!TUNNEL TRAFFIC extended IP access listpermit ip 192.168.2.0 0.0.0.255 192.168.1.0 0.0.0.255!Crypto ipsec transform-set esp-3des esp-md5-hmac TS!crypto card TUN_TO_HUB 10 ipsec-isakmpdefined peer x.x.x.x (replace with your public ip address of the hub)game of transformation-TSmatch address TRAFFIC TUNNEL
!gi0/1 interfacecard crypto TUN_TO_HUBRemote router 2crypto ISAKMP policy 1
BA 3desmd5 hashpreshared authenticationGroup 2life 86400!ISAKMP crypto secretkey key address x.x.x.x (replace with your public ip address of the HUB)!TUNNEL TRAFFIC extended IP access listip licensing 192.168.3.0 0.0.0.255 192.168.1.0 0.0.0.255!Crypto ipsec transform-set esp-3des esp-md5-hmac TS!crypto card TUN_TO_HUB 10 ipsec-isakmpdefined peer x.x.x.x (replace with your public ip address of the hub)game of transformation-TSmatch address TRAFFIC TUNNEL
!gi0/1 interfacecard crypto TUN_TO_HUBHTH.Evaluate the useful ticket.Kind regardsTerence -
Could not ping router RV042G public Internet address when it is after spending a SG200-08
I use the optical fiber Singtel broadband server. I installed a SG200-08 for UNTAG VLAN to port 2 and connect the port to port RV042G WAN 1. It works very well with a public IP address. Access to Internet is very well to router LAN ports.
However, I try ping on the public IP address of RV042G of the internet, I could not reach him. Everything what I'm missing in configuration SG200-08?
Hello
I don'i heard the switch block ICMP traffic as it has layer 2 switch, can you please check if the Ping on the interface of the router WAN is activate--> firewall--> WAN ping of uncheck block
Please rate this post or marked as replied to help other customers of Cisco
Thank you
Mehdi
-
Is it posible to the public ip address of the default locking?
Is it posible to block the public IP address by default on multiWAN routers?
I have several RV016 with up to 4 30Mbps Internet VDSL lines each and using the latest firmware to load 50-200 customer balance.
When it is used for navigation, some sites will have to lock public source IP of the customer (especially sites that requires a user authentication).
From a server point of view, public IP address will be between public IPs provided by ISP, automatic suite 4 round robin load balancing strategy.
As public IP, read by the server changed server reduced session, users will need to enter username and password again to connect.
Is it posible to lock this public IP for awhile to idle? (he has been featured on my old router BeWAN LX400H as "timer LockSource IP")
ebarriera,
The RV016 has no functionality like timer LockSource IP unfortunately. It's a common problem with load in the Cisco Small Business routers and key balancing mainly "secure them" traffic like HTTPS and RDP. I would test balance HTTP traffic and link HTTPS traffic to a WAN port and see if you get decent results.
-Marty
-
Numbering of the SIP Client IP addresses to public IP addresses
Hello
We are developing a new video network with VCS control and 2 highways of VCS. 1 expressway stressed the public internet address face and 2nd Expressway face partner network.
Requirement: Internal SIP endpoint need dial IP address public (via Highway 1) and the IP address of the partner (via Highway 2). VCS control configured mode "calls to unknown IP address" to "Indirect".
The two highways set up for 'Request to the unknown IP' mode to 'lead '.
There is research on the VCS control rules to find the IP address.
Priority 1 for IP address via 1st Highway
Priority 2 for Ip address of partner via Highway 2.
The two numbering IP addresses work, but component partner / IP address takes about 38 Sec to finish for the configuration of the call.
When I look at the history of calls on the VCS control, I can see even for the search for the IP address of partners, 1 internet search Expressway and could not reach the IP address and then start to search on the highway of VCS partner and find the Ip address, like that it takes more time to complete the call.
Sometimes, it is time and couldn't make a call of IP address to the IP address of the partner.
is he kind, we can minismise the time for setting up call for the IP address of the partner numbering.
Kind regards
Chris
Chris,
try to disable SIP UDP on both motorways as this should reduce the appeal of 30 seconds preparation time.
Hope this helps,
Andreas
Maybe you are looking for
-
Change the default color of Firefox opening links in a new tab
I use stylish addon for Firefox with a dark default css. I also changed the default window colors in the Windows registry. This changed the subject: white page to a dark color. But when I open a link in a new tab before the page is loaded, Firefox di
-
How to delete or merge identical to icloud contacts
Somehow I have duplicates of almost all of my contacts who say: "This information of contact has been synchronized to Exchange. If you want to change the contact information, please open OWA, and make your changes. » Is it possible to delete or merge
-
Second generation of airport express base station used to play music loses connection wireless, also a second express network, gen airport after about 30 seconds. Tried to change channels, reorienting the airport, using a different device - ipod and
-
HP Pavilion Sleekbook 14-b030tx NETWORK ADAPTER MISSING
Hello Please could you help me. My netowrk adapter disappeared due to the installation of windows 7 Ultimate version. Previously, my laptop came with the version of windows 8. And now, my drivers are missing. Even with the USB ports. Its not detectin
-
Hello I need to measure the deformation of 3 gauges (each gauge acquire strain of 3 directions). I would like to know if I could use 3 NI 9219 unit on a frame? Because I tried to use 2 capture card and I get an error! I have to use only one piece of