SAN information

Similar Questions

• SanLink2 and Dell Compellent SAN?

  Hello world

  I'm currently developing a sharing of the AFP on a Mac Mini with our Dell's Compellent SAN fibre channel storage.

  I have a late 2014 Mac Mini connected through love at first sight for a SanLink2 adapter CF 16 G.  The adapter has two HBA that is connected to our Cisco MDS 9148 fibre channel fabric switches.  The WWPN of the HBA on the adapter have been the subject of a zoning on the fabric buttons, and we cannot FCPING SAN HBA successfully.

  However, we have 2 TB of storage of our Compellent SAN to Dell for the mac mini, and I can't get the mac mini to see volume (do not see it in disk utility and can not see all the new drives in / dev).  I have a support case to open with promise, but he was curious to know if the community had seen.

  I tried fell different cable, different fibers and several reboots.  In my research on Google, I've learned a fun terminal command under OS X: fibreconfig-l [it's a lowercase L].  When I run this command, all I get is the following:

  terminalprompt # fibreconfig-l

  Controllers of

  Targets

  NodeWWN 23:00:00:01:55:5 B: 29:08

  NodeWWN 23:00:00:01:55:5 B: 29:08

  In my monitor OS X system, under the section of Fibre Channel, I get a little more information, but I'm under the impression that I should see (s) Lun in there and I'm not.  Here's what I see:

  Seller: promise

  Product: SANLINK 2

  Review: Firmware 1.1.65.30 material b

  Initiator identifier: 3791655135

  Node World Wide name: 23:00:00:01:55:5 B: 29:08

  Port World Wide name: 24:02:00:01:55:5 B: 29:08

  Address identifier: AE:16:00

  Description: Port 1

  Speed: 4 Gigabit ports

  Topology: Auto (point to point)

  Status: Connection established

  Cable type: optical fiber

  I can provide more information if necessary.  Thanks in advance if anyone has any ideas!

  Hello

  I know some FC HBA require that either a device mapped to LUN 0. For these HBAS if there is no mapped to LUNS 0 none of the storage will be recognized by the client. It has been my experience that whatever it is based on the older chipset of the LSI FC has this problem. The original SanLink FC HBA has no need of any drivers that was also the case for Apple brand LSI FC HBA OSX - thus could perhaps use the some of the previous control logic? Additionally, make sure that you are properly set up as point to point or FC - AL topology in the SANLink 2 configuration utility - this should match what is your San.

  Try this:

  1) map to the storage presented to the Mac with 2 SanLink to LUN 0

  (2) check the topology setting (try it was taking off from point to point auto and try first)

  (3) check if there is of"security groups" on storage that there ID WWN of the SANLink2 registered

  (4) make sure that the storage and the Mac are zoned properly on the FC switch (could be WWN zoning or rezoning of port, in both cases, it must be set up correctly).

  I hope this helps!

  -Jonathon Lee

• 2 san LUNS have been disassembled automatically need to pull up the same

  Dear Experts,

  last night all of a sudden we found two san LUNS are not mounted on one of the vcb server, but we are able to see the same on a disk management window, need your help how to mount these LUNS without losing any data. How to download buttons pressure or attachment...

  Need urgent help

  concerning

  Mr. VMware

  Hello

  What operating system is installed on the computer?

  Contact VMware support for assistance.

  http://www.VMware.com/support/

  Hope this information helps.

• GTA san andreas does not open with windows 7! How to silve this if you please help me

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: gta san andreas does not open with windows 7! How to silve this if you please help me

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Review the information from the Windows 7 Compatibility Center.
  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/search.aspx?l=en-us&type=software&s=Grand%20theft%20auto

  He says that version 2 is not compatible.

  If Aero is the problem, disable it before installing the game and then turn back on.
  I would say as you right-click on Setup and select "Run as Administrator".

  I hope this helps.

  Marilyn

• GTA san andreas incompatible with Windows7.

  Hi, I ais download GTA San Andreas on Windows 7, but when I run the game, of the he does not appear and he met me the message of the United Nations: "THE COLOR SCHEME has BEEN CHANGED. The following program performed an action that requires Windows to temporarily change the color scheme to Windows 7 Basic. "Etc... What do I do?

  Hi foxmccloud17,

  Unfortunately, the Windows Vista community is able to provide support in English. The following URL will help you to receive support appropriate for your location information. Open the link and select your region from the drop-down list, and then click the arrow to continue.

  http://support.Microsoft.com/common/international.aspx

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Nothing happens when I insert a San disk in the drive

  Original title: JONANDERSON_703
  When I insert the San disk in the drive, nothing happens.

  Hi JOHNANDERSON_703,

  Welcome to the community Microsoft and thanks for posting the question.

  According to the description, it looks like your San drive is not getting recognized in Windows Vista.

  He would be grateful if you can answer this question in order to help you further.

  1. have you made changes on the computer before this problem?

  2 is the issue limited only when connecting San drive?

  3 is the another USB device works fine?

  4. do you get any error message or connection error code car san?

  I suggest you to see the steps in the following Microsoft article and check if it helps.

  My drive does not appear in Windows Explorer: http://support.microsoft.com/kb/330140

  Note: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry

  If you need Windows guru, do not hesitate to post your questions and we will be happy to help you.

• San HQ 3.1 alert frequency

  Since the upgrade to SAN HQ 3.1, he wished to inform every hour vs every 6 hours as connfigured.  It beats the * out of us.  I have a failed drive and is on its way but to fight by alerting them every hour becomes annoying.   I'm set to alarm every 6 hours, which is ok.   This can be changed via the registry or other places or is this a known problem.   I've also configured notifications, but do not have the ability to set the frequency to 6 hours as before.

  Thank you

  Hello Mark,

  You can also change the interval on alerts of 6 hours 7 days.

  Under settings-> server-> Server E-mail Notification frequency settings

  There is a drop-down list it.

  

  Kind regards

  Don

• LAG does not not after more Guide of switch Configuration for EqualLogic San steps in the document.

  We use the information provided in the following document: i.dell.com/.../dell-networking-n4000-series-switch-configuration-guide-for-equallogic-sans.pdf

  We have two switches of N4032F which are stacked and followed almost word for Word from this document.  We do not use DCB.  We are trying to set up a SHIFT and follow-up step 2.11 in the document, but it seems that the SHIFT does not work.

  Switch 1:

  serial interface fortygigabitethernet 1/1/1-2

  No spanning tree portfast

  active in mode channel-group 1

  Switch 2:

  interface series fortygigabitethernet 2/1/1-2

  No spanning tree portfast

  active in mode channel-group 2

  However, when it was discovered after changing these settings it shows them as being inactive.

  

  Can someone please help?

  Thank you

  Jeff

  Thanks for the additional information. When the switches are stacked, they act as a logical switch. Then when you plug with an OFFSET you are basically creating a loop and hook up a switch on himself. Desempilement switches and just use the OFFSET for the interconnection of the switch and you should see the GAL go active.

• Network SAN seems slow

  Hello

  I am looking for input on how our Setup could be better organized. Overall, the best rate we can get is 30-40 MB/s tops. IO operations higher such as roaming profiles are an extraordinary amount of time. We use Citrix XenDesktop 7 with only 80 total jobs, often 50 are used on an average day. We have the normal assortment of other servers: Exchange, SQL, AD, file storage. I started thinking that maybe it's something with our Installer.

  Material:

  4 R810s from Dell, 4 builtin network cards are used for iSCSI, a PCIe card of add-in for both ports of 10 GB for ESXi 5.1 ethernet traffic. ESXi has iSCSI attributed to 9000bytes to the switch and port.

  1 EqualLogic PS6000xv (16 x 600 GB 15 k rpm hard drives, controller is 4ports all iSCSI traffic value, no port management dedicated)

  1 EqualLogic PS6100E (24 x 2 TB 7200 RPM hard drives, controller has 4 iSCSI ports and dedicated management port 1)

  These two without are configured as a balanced loading group. Frames of 9000 bytes is enabled.

  The San are related to our stack of core 2 3750 s Cisco. All iSCSI ports are vlan d together. Frames of 9000 bytes are defined.

  The ESX hosts are connected to a Cisco Nexus 5010. Two interfaces of 10 GB link the link to the 3750 s.

  Everything works the latest firmwares.

  What is an optimal configuration? Split the berries would be the best option? Did I miss something else entirely? I would appreciate any input. Thank you.

  -March

  You specify the model 3750, if it is the X, there is a Setup for this on the portal of quick setup guide:

  Go to this link, see the Configuration Guide (information on Setup network), and then click the Quick Setup Portal EqualLogic, link on this page is the configuration for the 3750 X and ESX settings.

  Also, you want to configure all of your ESX hosts in this document on best practices:

  en.Community.Dell.com/.../20434601.aspx

  Also, you must install a system running the SANHQ to help get a better understanding of your performance.  This can help support if after reviewing these documents, you can not get the expected performance.

  -joe

• Snapshots created with the EqualLogic VSS provider are not displayed in SAN HQ

  Hello

  Poster for the first time. We have just implemented an EqualLogic SAN, PS6100X network, and we're having performance issues between our DPM backup server, one of our hosts Hyper-V and VM images stored on the San. I will try to provide as much information as I can

  Environment:

  Dedicated iSCSI using Dell Force10 switches network

  hyper-V (Windows Server 2008 R2) 3 hosts
  -2 hosts has a NETWORK 4 port GB dedicated adapter connected to the iSCSI network; 1 host has connected to the network iSCSI NETWORK 2 GB dedicated ports card
  -Each Hyper-V host computer has a dedicated on the EQ SAN, RAID-50 volume that stores the Hyper-V virtual machines
  -EQ VSS provider installed on all hosts Hyper - V 3 and works correctly

  Using DPM 2010 for backup

  Problem: on Hyper-V hosts 1 and 2, any/all backup activities are very slow. On the Hyper-V host 3rd, however, activities related to backup all are incredibly fast! We compared the NIC configurations, HIT / settings ME and ASM, but we cannot understand why it is so slow on hosts 1 & 2.

  In addition, whenever DPM 2010 tells the EQ VSS provider to create a snapshot, we see the snapshot being created in the EQ Team Manager, but he does not appear in the list of iSCSI connections. According to the documentation SAN HQ, instant and volumes should appear here.

  We also disabled TcpAckFrequency for all 3 hyper-v hosts. It helped a little, but there is still a HUGE difference with regard to backups of the DPM.

  We're pretty sure that there is something misconfigured on the hosts Hyper - V 1 & 2, given that the host Hyper-V 3 has no performance issues.

  How can I get snapshots to appear in the list of iSCSI SAN HQ connections?

  Version information:
  SAN AC = 2.2.0.5924
  Storage Array Firmware = 5.2.4

  There are two different issues in this post for the SANHQ doesn't show only not iSCSI connections.

  Now SANHQ displays the correct total connection number but doesn't provide details of connections individual iSCSI for snapshots, which it should. So in the meantime use Workgroup Manager that shows the details for each snapshot (I know that's not the best answer, it's a short term solution).

  The fact the SANHQ shows details of instant connection does not mean that they aren't here and I can't imagine anything to do with the question of the DPM.

  The real difficulty, look for upcoming beta SANHQ and subscription for this on the EQL support site. You can do it now.

• Oracle DB on SAN PS6000XV

  Hello

  We will install our Oracle DB on PS6000xv 11.2.0 (what is a SAN).

  What should be the points of attention for architecture and distribution of files and...

  Thank you.

  This link has several publications for Oracle:

  http://en.community.Dell.com/TechCenter/storage/w/wiki/2632.storage-infrastructure-and-solutions-team-publications

  In addition, the support site: eqlsupport.dell.com (required active support agreement) in resources > document > reports tech section has additional information.

  -joe

• SAN IOPS / vFoglight s

  VFoglight can provide information about PAHO are / s current and historical IOPS / s of the SAN connected hosts use it? In this case the only systems using the SAN are monitored by vFoglight so all SAN activity is from these only hosts of hosts. Perhaps there is a canned report that can produce this info?

  Sidebar open right – Datastores & slipped to your personalized dashboard - select View - Make sure Show by role is disabled, select store data high-flow-vtable - next - filter on unwanted data warehouses - finishing

  

  To choose what measures, you want to display in the view click the customizer (arrow below).

  

  Don't forget the numbers you see are the average numbers on the timeperiod you chose. You can change the timeline and move as well.

• MS Sans Serif fonts is greater

  The police MS Sans Serif looks bigger. The dialog boxes for many programs use this policy, in particular the regular MS Sans Serif 8 and 10 points.  Although these programs have worked in XP, we have the problem in windows 7. police is greater, and the result is missing characters in the cells and the missing lines on the tables of the program. Since I have no control of the specified program of policies, I would like to know if there is an update of this font available that could improve its appearance.

  Sincerely,

  Hüseyin Ali Dogan

  Hey, Hüseyin,.

  Step 1:

  Make sure you have defined the correct setting of the DPI [dots per inch (DPI)] and also the right kind of claire.

  See the below for the links to do the same thing:

  http://Windows.Microsoft.com/en-us/Windows7/make-the-text-on-your-screen-larger-or-smaller

  http://Windows.Microsoft.com/en-us/Windows7/make-text-easier-to-read-using-ClearType

  Step 2:

  Try the mentioned registry fix in below:

  The registry setting:

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Fonts\MS Sans Serif 8,10,12,14,18,24

  is set to SSERIFF. FON on a system that has begun to 125% DPI. The parameter is set to SSERIFE. FON on a system that started 100% DPI. Note that a character changes of file name of F to E. The actual font files used can be different on Windows systems for other languages or code pages.

  To repair the system, you will need to change the settings for the new file names (changing the corresponding letter of F to E) and restart.

  Note: The registry changes will not take effect until the system has been restarted. You MUST restart after making the registry changes.

  Here are the contents of the fonts Fix.reg file to make changes to a system in English:

  Windows Registry Editor Version 5.00

  [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Fonts]

  "MS without Serif 8,10,12,14,18,24 'is' SSERIFE. FON. "

  "MS Serif 8,10,12,14,18,24"is"BENNY. FON. "

  "Messenger 10.12.15"="RUN. FON. "

   

  [Click Start, in the search bar, type regedit.exe and press ENTER.]

  Registry warning:

  Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows:

  http://support.Microsoft.com/kb/322756

  Kind regards

  Savan - Microsoft technical support.

• Port of SAN-Television - no operational Member

  I'm trying to set up a channel between a UCS and N5k FC port.  The environment is UCS 2.0 (3 c), 6248 s, 5548 s, EMC VNX 5300.  When I get out the uplinks FC left the channel to port, that they work fine, no error and I get successful flogi.  When I configure the port-channel on the UCS and N5k, I get the error code "failure - No. operational members ' F0282.  Here are the summary of the port-channel information and configuring the ports to the UCS and N5k, the fabric and fabric B have the same problem, this is the config only one both are the same.

  UCSM - Has (nxos) # see the sum of san-port-channel

  Link B-watch suspended S I - Individual U - Up D-Down

  Summary header
  --------------------------------------------------------------------------------
  Group-Type Port Protocol Ports members
  Channel
  --------------------------------------------------------------------------------
  121 fc1/32 (D) fc1/31 (D) of San - CFP (D) CF CF po121

  san-port-channel interface, 121

  active channel mode

  NP switchport mode

  interface fc1/31
  strength of group channel 121
  no downtime

  interface fc1/32
  strength of group channel 121
  no downtime

  NEXUS-01 # see the sum of san-port-channel

  Link B-watch suspended S I - Individual U - Up D-Down

  Summary header
  --------------------------------------------------------------------------------
  Group-Type Port Protocol Ports members
  Channel
  --------------------------------------------------------------------------------

  11 fc1/32 (D) fc1/31 (D) of San - CFP (D) CF CF po11

  interface san-port-channel 11

  active channel mode

  interface fc1/31
  Channel-Group 11
  no downtime

  interface fc1/32
  Channel-Group 11
  no downtime

  Thank you very much for the help!

  Hello John

  You can check if you have enabled fport-channel-trunk on the N5K switch?

  displayed in the function

  Otherwise, please allow it to

  conf t

  fport-channel-trunk feature

  Then make a stop / not closed to the port-channel interface.

  Padma

• Adding a user role for SAN switches

  I'll try to find the correct location in 3.3 ACS to add the following: roles = "network-admin". We have our SAN with Ganymede switches +. When one user other than admin connections, you get the role of "network operator". The Cisco MDS 9000 Family Troubleshooting Guide, version 3.x doc explains the role if you are using IOS/PIX Radius. Thank you.

  Hi Ed,

  Here is the link,

  http://www.Cisco.com/en/us/docs/storage/san_switches/MDS9000/SW/rel_2_x/San-OS/Configuration/Guide/cradtac.html

  If you are looking for:

  GANYMEDE + custom attributes can be set on a control access (ACS) server for various

  Services (for example, shell). The Cisco MDS 9000 family switches require custom GANYMEDE +.

  attribute of the shell of service to use for the definition of the roles.

  Cisco ACS GANYMEDE +.

  Shell: roles = "network-admin".

  Shell: roles * "network-admin".

  Cisco-av-pair * shell: roles = "network-admin".

  Cisco-av-pair * shell: roles * "network-admin".

  Cisco-av-pair = shell: roles * "network-admin".

  On GBA, if you go to: the Interface configuration, GANYMEDE + (Cisco IOS), check nex to: "display a window for each selected service in which you can enter custom GANYMEDE + attributes.

  Then, go to the configuration of groups and define the role information according to the above attributes.

  Hope that helps

  Kind regards

  ~ JG