Satellite A500 - problems with the creation of recovery disks

Similar Questions

• Satellite A500 - problem with the monitor after restoration

  Hello
  I have a Satellite A500. He has a problem with the monitor for a while, when you turn it on it's all lines etc. and you can not read but once the laptop to boot completely it is fine. My problem is that I wanted to do a restore, but I couldn't because the screen problem it started so I plugged into an external monitor and perform the restore. That has worked well.

  But now the laptop recognizes any my laptop screen. When you go to view it offers no other monitor choice other than external, I used for the restoration. I downloaded the display driver but nothing has changed.
  ANY IDEAS?

  Thank you

  (I have the disks for the restoration, if that helps.)

  > There a problem with the monitor for a while, when you turn it on it's all lines etc. and you can't read
  If I understand you right you can see when laptop starts and you see Toshiba welcome screen. Is this good?
  When you enter the BIOS settings you see thise lines too?

  Later, when you see the desktop on the external monitor, you can use the FN + F5 key combination to switch between an LCD and external monitor. Please try to use it and post comments if it works or not.

  What operating system do you use?

• Satellite A500 - problems with the temperature of the GPU

  The thing is playing Age of Empires online I started having problems with the temperature of the GPU. When you run the AIDA64 the CPU stress test can hold up well, but after 35 minutes the test what AIDA suspended while the GPU fan can't seem to download their revolutions, (I guess that if there was that a rise in temperature would increase the speed of rotation of the fan, don't).

  I consulted the manufacturer of the GPU, nVidia, (the graphic is nVidia GeForce GT 230 M) and tell me to contact Toshiba for other options, since, according to them, the problem is not the GPU.

  Any ideas or suggestions?

  You use your laptop to factory settings?
  Have you installed something that may be responsible for this (non-Toshiba display driver)?

• Problem with the HP G62 recovery disks

  Hello

  I'm having a problem with the restoration of the operating system on your laptop HP G-62. When I first bought the laptop, I was unable to make the recovery discs, so I ordered recently a few new HP. Because I have installed Ubuntu on the laptop, I wiped it from the disk hard drive used Wipedrive to remove the old Ubuntu operating system I had installed.

  Laptop computer reads the first disc ok and installs the component of windows, but when the screen lights up asking the two disc number it freezes and never installs anything when you try to move anything that used to screen it doesn't matter what and he used to install the second disk. He repeats just 'Please wait '.

  Thank you, Robert

  Hi, Robert:

  I can't help you get the recovery disks to work, but if you can read all 25 characters of the product key 7 windows on the bottom of your PC, you can do your own installation disc 7 windows to reinstall the operating system.

  Here's how:

  If you can read the Microsoft windows 7 25-character product key, you can download simple Windows 7 ISO files to burn on a DVD for the version of windows that is installed on your PC, and which is listed on the Microsoft COA sticker on your PC case.

  Burn the ISO with the option to burn the ISO on your DVD burning program and burn it at the slowest possible speed that will allow your program. This will create a bootable DVD.

  Or use the installation of Windows 7 USB/DVD tool to compile the ISO file that you download from Digital River. Link and instructions below. You need a 4 GB flash drive to use the USB compilation method.

  http://www.microsoftstore.com/store/msstore/HTML/pbPage.Help_Win7_usbdvd_dwnTool

  Use 25 characters on the PC product key to activate the installation.

  The key will activate a 32 or 64 bit installation.

  Then go to the support of the PC and driver page to install the drivers you need.

  Link to downloads ISO of W7 is below.

  http://www.mydigitallife.info/official-Windows-7-SP1-ISO-from-Digital-River/

  Paul

• Satellite A500: problem with the driver of sound and display after update!

  A500 Windows 7-64 bit

  I download the latest driver (6.0.1.6048) sound and display driver (8.16.11.8973) and I have a few problems.
  The colors are too bright and the sound is too deep (as the middle are too low).

  Hello

  Then why you n t go back to earlier versions of the driver?
  In your case, I would recommend setting the operating system at the point of time at first, until you have updated the drivers.
  Usually, this should help to recover the old drivers again.

  Welcome them

• Satellite L450D-failure of the creation of recovery disks

  I just bought the laptop above and tried to create discs of recovery twice.
  Both times, there is no on the first DVD with the following error message:
  Differences between the following files
  D:\HDDRecovery\ODDFiles\sources\boot.wim source path
  E:\sources\boot.wim path target
  0216F-3 c-00000000 error code

  I found a similar position on a Google search that gives to think that there is nothing I can do about it except contact Tohiba and get the recovery media unless the disc is damaged.
  I'm certainly not ready to pay for these discs, because it is not my fault that I can't create them.

  Is there something I can do and what advice can be given on the replacement for the recovery discs?

  In my opinion, there are two options for you:
  -contact your local agent where you bought your laptop and ask for replacement or
  -Contact nearest Toshiba authorized maintainer and explain the situation.

  I imagine that they can order one for you and it will be covered by the warranty.
  Do not wait for a long time and do it as soon as possible.

  One last thing:
  Can you please test if HARD OS installation disk works properly? Start as described in the follow-up paper - http://aps2.toshiba-tro.de/kb0/HTD9102IR0000R01.htm

• Problems with the creation of chips of debugging SDK WebWorks of Blackberry10 2.0.0.71

  I had a problem with the creation of debugging tokens using the blackberry-debugtokenrequest command. It gives me an error saying that "java" is not a batch file or a program. The blackberry-debugtokenrequest batch file has the following text:

  @java - Djava.awt.headless = true-Xmx512M - cp ' % ~dp0\... \lib\EccpressoJDK15ECC.jar;%~dp0\... \lib\EccpressoAll.jar;%~dp0\... \lib\TrustpointAll.jar;%~dp0\... \lib\TrustpointJDK15.jar;%~dp0\... \lib\TrustpointProviders.jar;%~dp0\... \lib\BarPackager.jar;%~dp0\... \lib\BarSigner.jar;%~dp0\... \lib\KeyTool.jar;%~dp0\... \lib\DebugTokenRequest.jar ' net.rim.device.codesigning.debugtoken.DebugTokenRequest % *.

  I think that the culprit is the symbol @ before java, does anyone else have this problem? Is there a solution?

  What happens if at the command prompt just type "java-version" of your command prompt?

  If it does not, you must do one of two things.

  1. install Java v1.6 (32-bit only)

  2 Java is not in your PATH. (http://www.java.com/en/download/help/path.xml)

• Problem with the creation of catalog upgrade to LR3

  Hello world

  Upgrade to LR3 tonight and I'm having a problem with the creation of the catalogue. I had 2 choices during the implementation and what I chose created a LR2-2 cat. I thought he was going to update my LR2 cat in a new Cat LR3 (as when I went to v1 to v2), but it didn't happen. I uninstalled and tried again, but is never given this choice to Setup again.

  So, how can I roll my current cat of LR2 in a new LR3 and use that to proceed? I have to do an export and merge?

  Thank you!

  This catalogue of LR2 - 2 is a copy of your old catalog, updated to the LR3 format. In other words, it's what you want.

  CTRL + O to open the catalogue and go ahead to use it.

• Problems with the installation of recovery - Satellite A300D - BSOD

  Hello

  The laptop in question (TOSHIBA Satellite A300D) recently stopped starting (BSoD).

  So, I tried using the recovery disk, but there is no help. What happens is:
  -After about 10 minutes of waiting, the first language menu load, so I click on "next".
  - Then I again click Next and accept the message that my HARD drive will be erased
  - Then I see a cmd prompt that says "try to remove all the letters of partitions possible...". »
  -There is also a minimized command prompt that says something like "RAID failed to initialize."
  -And then nothing happens.

  Is this a hardware problem? I also tried a full installation (instead of recovery), which, even once, is simply not. None of the errors is - it just freezes.

  Any help appreciated.
  Thank you.

  It is not easy to tell what can be the problem, but if you were not able to install the OS by using two different facilities CDs/DVDs, so there must be a problem with the HARD drive.

  The warranty is still valid?
  I mean you can contact the nearest Toshiba authorized service provider and explain the situation. They can swap the HDD and again test the recovery procedure.
  Can you get somewhere 2,5 SATA HDD for testing?

• Satellite U500 - problem with the cooling system has been detected

  I have a Toshiba Satellite U 500 series, and I just got a message saying "a problem with the cooling system has been detected. Please turn off the power immediately and return it to service.
  Before that, I would like to know if anyone has had this problem and if there is a software solution?
  HIERARCHICAL

  Check HERE to see if anyone else had this problem in the past.

• Satellite A200 - problems with the AC adapter / CC

  Hello

  The problem concerns a Satellite A200 (PSAF6A-02H01N).

  Recently, there was problems with the laptop, taking several attempts to boot to Vista, it would lock up while loading or just hang and freeze just after loading Vista.
  But once it was up and the laptop running would be happy working for hours with the AC adapter is plugged in.

  The problem got worse now and the laptop will not load Vista end without crashing.
  We have now reduced the computer down to have only a problem when the power adapter is connected.
  The laptop battery will charge normally with the AC adapter is plugged in and the laptop on standby or off.

  The problem persists with the AC adapter is plugged in and the battery removed.
  The laptop will start and run perfectly with battery and no power adapter plugged. Once the AC adapter is plugged in the laptop indicates that the battery is charging and then after a few seconds it crash or freeze and the only escape is a full stop.
  The laptop will not work under the battery power for 30 minutes max.
  I checked the output voltage of the AC adapter and this seems to be a consistent 19.4 Volts.

  Is this only a problem of AC adapter or the problem with the laptop?

  Thanks in advance...

  The Canada Gazette

  I lifted the previous discussions on this problem and found one that was very similar, but unfortunately the user decided not to find the problem of the road, save money and buy a new laptop instead! Hmm. !! .. seems to me like this might be a prob. material. Maybe a new motherboard?... anyone have an idea of what are the costs for that perhaps? .. an ASP or decent technician backstreet?...

• Re: Satellite C650 - problem with the devices connected to USB ports

  Hello

  Can help someone, I have a C650 and everytime I try to connect to something to him via the USB ports, it is not "found" by the computer?

  The other night, I tried to get pictures on my phone but it wasn'; work and I put it down to a problem with the phone, but today I tried to install something digital crafts for my daughter and during installation it tells you to insert the thing into the USB port and click Next, when I do that he's going through a lot of "research" and said then it can not be found.

  The laptop makes a beep sound as it would on an extraction device when you plug... I hope that makes sense. So I am now assuming that the problem is with my computer, is there something I can do to fix this?
  Thanks in advance

  Sorry should add - it's like nothing is plugged at all when it is, and it happens on two USB ports, not just one...

  Post edited by: leahhw123

  Hello

  What happens with plug n play like USB mouse device?
  You are able to use an external USB mouse correctly?

  > but today I tried to install something digital crafts for my daughter and during installation it tells you to insert the thing into the USB port and click Next, when I do that he's going through a lot of "research" and said then it can not be found.
  I guess this could be a problem with the software or drivers installed.

  I searched a bit and his city that he has a software is compatible with windows vista/2000/xp. Win 7 is not mentioned do not know if this could be a problem, but in your case, I recommend asking the support of this software product for some advice.

  In addition, you can try to install this software once more, check whether this USB problem appears again.

• Problem with the creation and display of intelligent insights

  I have a problem with the intelligent preview function. I use Lightroom 6.4 on Windows 10.

  • When I hit the "Original Photo" icon under the histogram in the develop Module, nothing happens: the remans icon exactly the same and no record Preview Smart is created in the catalog folder.
  • When I create a Smart overview in the library Module (library-> Previews-> generate Smart previews), a Preview Smart folder is created in the catalog folder, BUT , in the module development, l ' icon below the histogram says still 'Original Photo': it does not seem to recognize that a smart preview is available.

  Any idea?

  Rob.

  If everything works as you want, so you can leave the open Historgram.

• Problem with the creation of variable names

  Hi, I have a problem with the following function:

  private function whichLevelToLoad (): void {}

  If (levelToLoad == "no") {}

  currentLevel = null;

  }

  var thisObj:Object = new Object();

  {if(levelBtnArray!=null)}

  for (var j: int = levelBtnArray.length - 1; j > = 0; j-) {}

  If (levelToLoad == String ("level" + (j + 1))) {}

  thisObj ["level" +(j+1)] = new ["Level" +(j+1)] (); - > The Problem

  thisObj ['level' + (j + 1)] .x = 0;

  thisObj ['level' + (j + 1)] there = 0;

  addChildAt (thisObj ["level" + (j + 1)], 0);

  currentLevel = thisObj ['level' + (j + 1)];

  }

  }

  }

  }

  I am trying to instatiate 75 objects by using a loop. The line should look like this "thisObj.level1 = new Level1(); with the numbers from 1 to 75. Is this possible? How

  can I do it?

  Thank you...

  getDefinitionByName solves this problem.

  Example of

• Satellite 1905 - problem with the touchpad after awakening from Hibernation/standby

  Greetings.

  I've known a few interesting problems with my Satellite 1905 - S301.
  Whenever he wakes up from hibernation/standby my touchpad stopped accepting "taps" as a click on the left button of the mouse. It works normally with finger motion detection, but stops at all but it is quite annoying to restart the machine whenever he returns from hibernation mode.

  I've done a small workaround and after I close the laptop lid still works but this isn't the way it should work, I would have preferred that she either Hibernate than running for 10 hours without any sense;).

  Can someone give me the solution to this problem, please?
  Thank you in advance.

  Kind regards
  Akar

  Hello

  I agree with you. It s very boring to restart the machine each time to use the touchpad.
  This problem appears on the first day?

  I think there might be a software problem and, possibly, the new installation of operating system recovery CD Toshiba could help.
  I know, the complete installation is not the best solution, but it might help.

  You should also check you the touchpad. Satellite 1905 - S301 was designed for the U.S. market and so I checked the American website for available drivers.
  It seems that 5.3.203.2 is a newer version of the Alps touchpad driver for Windows XP.

  I suggest to reinstall the touchpad driver and check if there is no improvement.