Satellite C870 - 19L can not set the correct resolution

Similar Questions

• Satellite C855 - 12K - can not install the correct display driver

  I have a Satellite C855 - 12K for the Croatian market. Recently, I noticed a loss of performance in games, even on settings low that I used to play normally high or ultra. So I decided to reinstall windows and get the latest drivers.

  All drivers installed correctly the display one, when I install and reboot the system and the laptop BSOD out restores.
  I tried to manually install the driver without any catalyst, but that does not work either.
  NET framework 4.5, directx 11 and vcredist are all installed in front of the pilot.
  Does anyone have an idea what this topic?
  Graphics card is the Radeon HD7610M.

  Update on this:
  I just managed to find the old CCC software (version 2012.0120.420.7502) and it installed fine.
  I am still concerned why the new driver does not work?

  Post edited by: markov

  Hi Markov

  According to the specifications of the laptop this model was delivered without BONES. Can you please tell us what OS you use and don't you try to install the driver on the Toshiba download page?

• Windows 7 sees my second monitor as "generic non - PnP" and will not let me set the correct resolution

  Hello

  I just installed Windows 7 Professional 64 bit on a new hard drive on my Dell Studio 540. The PC has a graphics card ATI Radeon HD 3450 and has a Samsung 226bw 22 "monitor on the digital output. This works very well, and has the resolution of 1650 x 4050. When I am running Vista (on the previous hard drive), I got a monitor flat 14 "old on the other out, and it worked fine (although at a lower resolution).

  I added a monitor AOC F22s + on the other output, expecting to be able to put this to the recommended 1920 x 1080 resolution. Unfortunately, Windows has developed the driver for this monitor "Generic non - PnP" and will not let me set the correct resolution. To the maximum it will allow is 1600 x 1200, (as well as all other resolutions it allows) do not use the monitor at maximum capacity, which is the ratio of evil anyway, so the display seems tense.

  I run Windows Update, so have the latest drivers. I tried to install the other drivers, but nothing helped.

  I tried to unplug the Samsung monitor and restart the PC, so that the AOC, one was the only monitor it and he always had as 'Generic non - PnP' with the wrong resolution.

  Someone at - it ideas? I'm at my wits end. AOC support did not understand and could only suggest that the monitor was faulty, but the place where I bought it insist that it works very well and so no Exchange or get a refund (no restocking fee, which is a RIP-OFF).

  I really want to use both screens and would appreciate greatly any help that anyone can give. I hope I gave enough information. If I didn't, please let me know.

  Thanks in advance,

  Alan

  PROBLEM SOLVED!

  It turned out that my VGA cable was wrong and that it was not send the right signal to the computer. The screen worked fine with a VGA monitor, but the PC has not said that the new monitor is a PnP I tried a different cable and it worked fine.

  Thanks again to all who have suggested things.

• Cannot install Windows XP on my Probook 4520 s in mode ACHI... can not find the correct drivers anywhere!

  Hi all!

  I'm a newbie here, please help me. Just bought a new laptop, 4520 s and can not install windows in AHCI mode. Very strange things are below:

  -I'm reading on this tread: http://h30434.www3.hp.com/t5/Operating-systems-and-software/No-SATA-AHCI-drivers-for-6440b/td-p/2592... And I havea even question...

  -Have these:

  PCI\VEN_8086 & DEV_3B2D. DeviceDesc = "Intel(r) 5 Series/3400 Series Chipset Family 2 port Serial ATA Storage Controller - 3B2D.

  PCI\VEN_8086 & DEV_3B2E. DeviceDesc = "Intel(r) 5 Series/3400 Series Chipset Family 4 port Serial ATA Storage Controller - 3B2E.

  Hardware items, but can not change driver PCHM SATA AHCI Controller 4 Port or Port 6 ...  BSOD and reboot even when...

  -tried to find out all the correct drivers, no results...

  -When it is used the nLite and running the Windows installation again with ACHI (setting in BIOS) mode I just receive this message in the first minutes of blue screen: can not find the ACPI. SYS... Press a key to reboot.

  Help me please guys, if you can.

  Thanks in advance, Peter

  I had the same problem and now works properly. That's what I did:

  1 position (BIOS) setting to IDE compatible mode

  2. install XPP as usual.

  3. install the drivers for the chipset Intel (sp46692)

  4. download and run softpaq for Intel Matrix Storage Manager (sp45106)

  5. go to the controller Start > Run > devmgmt.msc > IDE ATA/ATAPI

  > Port controller 5 series/3400 Series 6 Chipset

  6. set to update manually the folder c:\swsetup\sp45106, with option "have a disk.

  7. Select "PCHM SATA AHCI Controller 6 port".

  Windows says it is not compatible, but it will be restarted from the nest

  8 restart the computer, and set its mode controller SATA (BIOS)

  9 complete! Windows does not boot ok

  I hope you understand my instructions: English is not my mother tongue and may be poorly written. In any case, it worked for me.

  Miguel.

• Can not find the correct driver in Macbook - J4680c

  Hello!

  just install a print server on the network from my boss - netgearPS121v2.  everything is great with 2 Mac and a PC - everything can print, etc.

  all the macs print to print IP assistance and the appropriate driver.  for some reason, my boss pro macbook did not have the correct driver installed and all that is available to him is "HP Officejet J4680 series - Fax" that does not work.  I use the same macbook pro with the same system (10.6) and did not have a problem.  his machine was the Guinea pig for his assistant try to set up while on the phone with HP tech support.  (I was out of town and unable to install).  I have a feeling that this was an inadequate installation and hampered by technical support, try to fix it.

  any suggestions on how to completely uninstall the HP software so I can't completely re - install?

  Thank you!

  Steve

  Well Yes,.

  I guess that someone loaded the HP from the CD for the printer software (which is only 10.5 or earlier version).  Here's how to correct:

  Go to Applications/Hewlett Packard / click Uninstall HP
  Click on continue
  Highlight your device in the left pane
  Hold down the Ctrl and Opt Cmd and click on uninstall
  There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled)
  Click on continue and let it finish

  Now run a software update.

  Then, remove and reinstall the printer in System Preferences, Print & Fax.

  You do not have the software now since Snow Leopard as well print & scan drivers built-in. scan from Preview apps or Image Capture. Scan from the front panel of the printer does not work yet.

• Satellite L310 - I can not enter the Bios settings

  Dear team,

  I have a toshiba that is always on warraty.
  Is there anyway you can help me.

  It ceased to operate effectively. It does not exceed the Bios.
  By that I mean you reach the Bios screen, but you can not enter the Bios settings.

  Details
  model: toshiba Satellite L310

  What exactly do you say: you reach the Bios screen, but you can not enter the Bios settings?
  The BIOS is secured by password or what?
  You see a splash screen of Toshiba for short time?
  Is it possible to start the Windows operating system or to recover the laptop?

  Please publish more details!

• Satellite A110-277: can not access the internet wireless

  Hello
  I have a Toshiba Satellite A110-277. We have wireless internet access in our House and it was workin fine, but since a few days I can not access the internet. My laptop is certainly recognizing internet connection wireless, but through IE or Firefox it just does not connect.

  For some reason, he worked briefly through Firefox, but then that stopped. I don't see what anyone, I have done differently, other than (finally) updated Windows Media Player, but why would that cause problems, I don't know!

  I would really appreciate help as soon as POSSIBLE, that the internet is my lifeline to work!
  Thank you
  GcDh

  Hello

  You said
  > My laptop is no doubt recognize the wireless internet, but does not connect via IE or Firefox, it's just
  Hmm, I guess that you can connect to the WLan router and can insert the WiFi encryption key successfully right I'm right?

  How does LAN connection? Can connect you to the internet using the LAN cable?

  Feedback would be appreciated

• Problems with the DC Power supply QL 355TP: I can not set the tension level

  Hello

  I'm trying to control a power supply DC via GPIB. The power supply being used is the QL355TP of society Thurlby Thandar Instruments (TTi). There are no drivers of OR to control the instruments, then I need to download and install the driver from the website of TTi: the package I installed is as follows:

  "QL - P power supplies, (including QL Series II) series pilot National instruments (Labview and CVI)"

  and I also installed the following:

  "QL - P power supplies (including QL Series II) series, IVI driver"

  So, my problem is that when I try to use the sample application of the driver 'Volts.vi DC Ouput'; defines a specific level voltage, does not work properly. The application gives no error, but it is not set the specific level voltage. However, other functions work properly, as the measure or activate the output. I tried a lot of things, but I don't know why it does not work.

  I enclose the block diagram of the application and the front panel:

  

  

  I must say that I barely control instruments using Labview and is possible that this problem would be because I did not consider things basic and mandatory.

  Any help is appreciated.

  Thank you.

  p.s. Try to replace the decimal comma to period. It is possible that the driver does not correctly handle the comma.

• Can not keep the correct time on my laptop Dell M4500

  Hi all

  I, ve problem with time on my Dell M4500 laptop a few months. I tried several solutions but not worked. time holds as long as the used laptop however wake up after sleep time shows right from the start of the commissioning (sometimes for seconds, sometimes for a few minutes) and sets then went back to a wrong value. I checked the weather it is time windows or time of bios, actually, it was the time of bios that changes after getting return of mode 'sleep' and windows after the bios later time, and if I want to correct then I have to restart, go to configuration, change time bios and then continue until the next time...

  I, ve tried the following:

  battery 1-i bios modified by a new Dell... unsolved problem
  2 - Dell has provided new motherboard with a new battery (verified) and the last update of the bios > problem unsolved
  3 went to services.msc and turned on/start/stop windows.time service > problem still there
  4 enabled auto-sync > problem unsolved

  y at - it an idea about this problem? in fact I ve called Microsoft but they replied that time BIOS cannot be changed or affected through Windows because windows does not have access to the bios time, however after change of motherboard (changed with a new one) is it a physical cause for this problem?
  any help? Thank you
  Saami

  1. click on the date and the time on the taskbar.

  2. click on change date and time settiings
  3. now check if you have set the correct time zone. If not, click on change the time zone to your local time location and click OK.
  4. now click on the internet time tab.
  5. click on change settings.
  6. then check it in as a "synchronize as internet time server.
  7. then click Update now.
  Try the following steps

• How can I set the default resolution of the tabs, Favorites, etc...?

  Hello world
  I'm having a problem with my browser. About 5 days ago, I installed my graphics (nvidia geforce gtx 670) was last updated. Immediately after the update changed the look of my browser!
  The problem is obvious with the Favorites bar and the tab bar.
  This is the difference:
  Before: http://imageshack.us/a/img153/4573/g35.png
  After: http://imageshack.us/a/img62/7908/nbir.png
  Please help me!
  Here, there is some other information... I use a new installation of the latest version of the browser. New profile, no theme, no addon.
  It seems that this menu are in the correct resolution.
  Change in topic layout.css.devPixelsPerPx:-1 to 1.22 config makes things better. But I want the old default resolution.
  I have average - 125% for the resolution in the options panel.
  Does turning off hardware acceleration.
  Thank you much for the help!

  Hello

  Firefox on Windows is now after display, scaling options that can make the biggest text on screens at high resolution.
  You can adjust the resolution of your screen.
  To change it follow these steps:

  • Type of topic: config in the Firefox address bar and hit the Enter key.
  • If the warning that this might void your warranty , click I'll be careful, I promised.
  • Search for layout.css.devPixelsPerPx

  

  • Double-click layout.css.devPixelsPerPx to edit its value. The default value is - 1.0 in Firefox 22 and above. Change it to 1.0 to run as in previous versions of Firefox.

  If necessary, further adjust the value of 0.1 or 0.05. Values between 1.0 and around 0.5 to reduce the size of the elements. Use a value greater than 1.0 to increase the size. For example, a value of 1.25 will increase the font size of the 125% to account for the default DPI setting in Windows 8. Check the value that you enter. Definition of a value that is too small will take everything away and too high will explode things.

  If the web pages should always be adjusted so you can watch the extension Default FullZoom Level or NoSquint .

  To adjust the font size for the user interface, you can use the extension of theme font & size changer .

  This solve your problems? Please report to us!

  Thank you.

• Satellite A200 - 19L can not boot from the CD

  Hi guys,.

  I'm glad I found this forum site, I pretty well hope to find a solution here.

  Well, this problem is not very complicated, in fact my DVD player (model TS-L632) is not read more, so much so I decided to change with a new one, but it is not the same model as the original drive.
  It is the case of the generic DVD player really.

  Now when I inserted my recovery disk or any bootable disk is not booting the CD, and when I press F12 for I can't find any CD/DVD drive, but running in Windows I can't find the DVD player and it can read any CD priority boot normally.

  Just having the problem while booting from CD.
  I thought that maybe there is no security for this model that locked some hardware.
  So please guys want to help me how to understand it,

  any help would be greatly appreciated.

  Thank you

  > When I press F12 for boot priority I can't find any CD/DVD drive, but running in Windows I can find the DVD player and it can normally read any CD.

  The whole story seems really strange to me
  If you access the BIOS, you can see the details of the CD/DVD drive? The drive is recognized properly?

  If not then I guess that the STRANGE inserted is not totally compatible due to different master/slave/c-salt settings.

  > but running in Windows I can find the DVD player and it can normally read any CD
  It s also strange to me so that the CD/DVD drive appears in Device Manager even if the CD/DVD drive Startup menu option does not appear.

  But first check the BIOS

• Satellite C870-196 - how to set the password of BIOS access only?

  Hello

  I would like to put a password only to access or modify the BIOS and not to launch the system on my TOSHIBA Satellite C870-196.

  But I do not understand that is configured in the BIOS:

  -Set Admin password
  or
  -Set user password

  Thank you

  Kind regards

  Hello

  Here are some tips as the basis for a better understanding
  http://APS2.toshiba-tro.de/KB0/FAQ2503B00000R01.htm
  http://APS2.toshiba-tro.de/KB0/FAQ9202JE0000R01.htm
  http://APS2.toshiba-tro.de/KB0/FAQ9202JF0000R01.htm

  Check it please and if you have any other questions do not hesitate.

• Satellite P500 (PSPE8U) - can not find the drivers for it

  Hello

  I've been and down these forums without success. I watched a lot of forums for the drivers for my P500. I've been through the pages of support sites toshiba of Europe, Uk, Australia and Japan... no chance either. I tried to contact the ebay seller I bought, apparently it is now out of business. It goes without saying that the laptop came without any driver disk. Unfortunately, one of the drives died on me and had no time to do a recovery with all the drivers disk. So now I'm really stuck. Here are the details of the laptop should anyone have brain waves for me-

  P500 - PSPE8U
  Windows Vista 64-bit
  ATI HD 4650

  At the time the largest bad head are the video drivers and my battery life is around 30 mins without the toshiba software. The stock of the resolution is a disaster without the correct driver. I tried the ATI46 drivers * from their site, but the application tells me that my hardware is not supported.

  Any help would be appreciated.

  Thank you
  Chris

  Hi Chris,

  Satellite P500 with model PSPE8U number belongs to the US models and therefore all the drivers and tools that you can find on the Toshiba U.S. page:
  http://www.CSD.Toshiba.com

  Just check the underside of your laptop again for the exact model as P500-S1234 number, then you can find the right drivers for your model. :)

• Satellite L35-S1054: can not get the Atheros 802 .11B/G to work

  I can't get the internal WIFI to work! I wiped the day the first HARD drive and reinstalled a fresh XP Pro SP2. I manually installed all drivers except toshiba machine has not properly categorized them. Does anyone have a link for the real for L35-S1054 Atheros wifi driver?

  Also, how to turn on the radio for him once it is properly installed? I see a Fn F8 button that looks like the radio, but it does nothing. Do I need a hotkey program to do this work?

  Help!

  And thank you!

  Hello

  The discussion is a little confuse
  Have you checked the Device Manager and checked her if the Wlan card driver has been correctly installed? Check it out.

  But back to the root. The device seems to be a mobile American. I put t know if the American notebooks come with drivers CD or not, but normally you should have the drivers on the support. If this isn't the case, then the image of Toshiba contains options for creating a CD of drivers and tools clean.

  The laptop with Atheros Wlan card supports also an Atheros Wlan client utility.
  This sets up the WiFi connection. You have 2 options. You will use the clean Windows configuration or you will disable her and use Atheros client utility.

  But in a first time, you must activate the Wlan with the switch on the side of the laptop and the Fn + F8 key combination

• Satellite Pro P100 can not get the screen to work again

  If someone could point me in the right direction, I would be very grateful!

  I bought a monitor to use when I am in the office (it's a LG Flatron L225WT), installed the software that came with it and plugged. Nothing seemed to happen, then in Toshiba HWSetup, I changed my power on the screen 'LCD + Analog RGB'.

  To cut a long story short, the external screen works perfectly now, but I cannot access the internal screen, even after changing the power supply on the display to 'Automatic Selection '. The Fn + F5 key does not appear to have any effect at all.

  I must have inadvertently done something to mess up the computer. Can anyone suggest how I could reset it back?

  TIA to all who can help you!

  -Laurence

  I put t know what laptop you have and don t know what OS you are using, but it seems that you have managed to set the external monitor as the main screen.
  You should change in display properties (right click on desktop-> properties)

  Somewhere in the settings, you should try to score the internal display (1) and should mark use this device as the primary monitor

  You won't find any similar settings or this will not help then set the operating system to the point of time at the beginning. In this case all settings will be reset!