Satellite L30: Connection to a printer via USB Windows XP

Similar Questions

• HP LaserJet MFP M425dw 400 pro: cannot connect to the printer via USB

  Hello

  My problem is as follows:

  Since December 2014, the HP printer has been connected via USB to the desktop (at the time using windows 8.1) and by the network to other computers. The problem is with the 10 windows desktop where it is widely used for double-sided scanning.

  Yesterday morning I came only to find out that HP will not work in no case with Office for Windows 10 USB - connected, changed the ports that are 6, the cables, the office will say it is not connected. However, it connects through network for printing but not scan, it gives an error about Scanner HP not connected but will scan with Windows Scanner and fax with the printer using the scanner for the work of network folder - which can not scan two-sided.

  I uninstalled the driver, reinstalled with HP Support Assistant / downloaded directly from HP, same thing. The problem is that it be increased to 99% on the screen that shows the connection to the printer (the one detecting the USB cable) when it will say:

  "

  Error

  A Setup operation took too long to run. It is a fatal error, preventing the use of the product.

  If please restart your computer and run this installer again. If the problem persists, please visit the web site of product support for your product. »

  I tried the original shipped with the printer CD, it gives the same error message.

  If anyone can help I will be very grateful. Thank you!

  Too bad! Fixed it myself using the Hp Smart Install supplied with the network interface of the printer.

• Impossible to print via USB using my iMac running 10.6.8 Officejet 4635

  I bought this printer all in one HP Officejet 4635 yesterday and are unable to print via USB.  I have an iMac running OS 10.6.8.  Until I'veI tried all of the suggestions that I could find on these forums (ex: downloaded the latest driver, disconnect/reconnect the power to disconnect/reconnect usb, delete and 'Add PRINTER' again, etc...) The computer does not recognize the printer, but displays "Unable to send print data" after I click on print.  I know that the printer works very well because I was able to send the document directly to his personal email address.   Help, please!

  Hello! Welcome to the @DanLA forums

  I have seen your post about how you can't use your Officejet 4635 with your iMac running 10.6.8. I understand that you have already tried troubleshooting, so please ignore all the steps that you have already tried in the list of my own suggestions below. If you still can not connect then, think of give us a call. I'll leave the details below.

  1. Mac OS X: how to reset the printing system
  2. Repair disk permissions
  3. Restart your Mac
  4. Reinstall the complete driver: 4630 Officejet HP e-All-in-One Printer full feature software and drivers series
  5. Try another USB cable
  6. Look for an update of the Firmware: get the latest Firmware and updates
  7. Make sure that the printer is plugged directly into the wall, avoiding bars power and surge protectors. This ensures that the printer is full on and can help.

  Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Good luck!

• We can connect HP1000 J110 printer via bluetooth

  We can connect HP1000 J110 printer via bluetooth

  No,

  The printer is a USB printer only.

  You can find the specifications of Connevtivity below:

  http://support.HP.com/us-en/document/c02231304

  Shlomi

• EPC2203 modem cannot connect to the Mac via USB?

  I searched all threads and you can't find something to solve my problem.

  My ISP sold me the modem Scientific Atlanta EPC2203 cable recently. I can't connect it to my Mac (10.5.7) via ethernet no problem at all. But I can't get a connection via a USB port. The modem operating manual mentions for Mac OS X USB connectivity, but does mention all the details on how to establish the connection: we talk about the installation of PC drivers. Supplied with the modem installation CD only applies to the PC, it seems that I have to take extra steps such as installing a Mac driver? I couldn't find the Mac drivers adapted on internet, then I start to think that this modem is not simply done to connect to the Mac via USB?

  Any help is very appreciated.

  To make your Modem work with USB connectivity, you must install the Modem drivers on your computer. You can try to search for the Drivers that works on the MAC computer or else you can contact the support Tech Atlanta, because they can let you know where you can find the drivers for your Modem. Or well you googled around and you can find the drivers for your Modem which are Compitable MAC.

• Pictures of blackBerry Z10 BB Z10 disappeared when connected to the PC via USB Phone model z10 STL 100-1

  Help on unit Photos and videos not Visible when connected to the PC via USB. I also tried to restart and reinsert the SD card but no response what happens each time I take pictures and try to transfer to the pc via USB please help to recover the photos suggest something?

  ampawase wrote:
  Help on unit Photos and videos not Visible when connected to the PC via USB. I also tried to restart and reinsert the SD card but no response what happens each time I take pictures and try to transfer to the pc via USB please help to recover the photos suggest something?

  "A wireless connection with the mixture, use the file manager, hold Media Card - Photos - 'Shift' or ' Ctrl ' key - select thumbnails - right-click - Save slot - selecting a folder on the pc and save them.

• OfficeJet 6500 E710n-z: where to locate X 86 Drivers for Win 7 to print Via USB system connected to the network using Win 8.1

  Since my computer can only connect to a printer wireless via USB, other computers on the network cannot connect to the printer.  The possibility of allowing other printers using the main system of sharing, I need the x 86 driver but cannot locate it on the HP support.

  Seems there are a lot of problems installing with HP systems, I would hope that society can give a high priority to these issues.  Many of us love quality HP but wireless connectivity is frustrating.

  In a humorous way, please remove the "cannot find the printer - make sure that the printer is plugged in and turned on."  statement.  Our children know how to set up a network, so that the statement is hilarious, until you see for the 20th time as possible motive to the wireless printer is not found on the network.

  Hello
  My post seemed to have grown to a case manager who was willing to put up a time for the members of technical support to contact me.  By the way, she asked about the distance, the printer from the router, which, by other reviewers, should be placed next to the printer, and she asked for me to try to move the router to about 18 inches from the printer so that it would be responsible for coordinating the call of support following our conversation.

  I did it and all network issues related to wireless access by the entire Office has been resolved and performing network and each station can print and scan in a few minutes, following a job application.  Printing took about 20 minutes to start and sweep was impossible until this Council been offered.

  Many congratulations to Yvonne!  And, I thank you for following up on this post.  I am a very satisfied customer again once my application has been met with personal concern for the issue and an appropriate resolution and FANTASTIC found!

  Thank you once again,

  Rick

• Satellite C660 now does not connect to the printer via Bluetooth

  I have a very small domestic network - 2 of the Satellite C660 using Windows 7 Home premium and a printer Photosmart more connected through BT Home Hub work all fine until a computer laptop suddenly cannot connect with the printer, well located 1 m from each other.

  Connection Internet is fine - and another laptop works perfectly. Message from the printer on statement failed, on examination, it simply records as "error."

  Any ideas of solution?

  Hello

  From this point it's hard to say what's wrong.
  In my opinion, you must reset all settings and configure the connection to the printer again.
  Reinstall the software that you have installed in the past.
  Also recommend check that the support from the manufacturer printer pages a few FAQ, HowTo, etc...

  Since your laptop can connect to the internet properly, it cannot be a laptop problem

• HP Deskjet 3545: hp deskjet 3545 my desktop pc does not connect to the printer via the usb port

  Hello

  I installed all the drivers and the software correctly and the printer can communicate with my desktop pc for problem analysis, but when I open an editor like notepad, word, write something in them or when I open a photo and when I try to print, it cannot communicate with the printer. I used same HP print and Scan Doctor in order to study the problem by clicking on the button "Correct the impression", in the program, he sees even my connected printer (usb) or same (LAN), but printing HP and Scan doctor after reviewing all the steps and ticks as ok, when he said "try to send the test page" and when he tries to send it to the printer It does not send and I choose "no print" to see which program will thus be, discover the program this time said "send the in-house test page", and I chose this option to send it internally and the printer works. The program says "there is a problem which can not find this application for assistance. try to uninstall and reinstall the drivers as an adviser"but I uninstalled and reinstalled the drivers and seems that there is no error, or any problem with the drivers, but seems that it cannot connect to the printer, even if I can use the scanner of my office and it connects to the printer without problem. What can be the problem? How can we solve this problem? any help would be appreciated. Thank you. Windows XP Professional Edition, 32-bit SP3 is installed on my desktop.

  Sincerely

  Hello metehangunaydin,

  Please try the procedure below so that you can at least be able to print.

  1. click on the Start button on the computer.
  2. then click on Control Panel.
  3. then printers and faxes
  4. in the top left, click on add a printer
  5. click Add a local printer
  6. and while "Use an existing port" is selected, select "Virtual USB port... "and then click Next.
  "7. in the manufacturer list, select HP, then under the Deskjet 990 c printer list", then click Next and complete the wizard

  Now try printing. It should work.

• Unable to connect to the printer via IP address

  I changed my ISP (internet service provider) and therefore changed routers - now unable to connect to the printer.
  I put a static IP address on my HP Photosmart B110a printer before we changed to ISP because there are connection problems. When we were setup to the ISP again, we are unable to connect to the printer, such as the printers IP 192.168.1.12
  The new network ISP IP range is 192.168.0.xx and printers address IP is out of the network.
  I can print via the USB cable but I can't return to my printers GUI by entering 192.168.1.12 return the printer back from the static IP address.
  A hard reset for this printer would be appreciated.
  Thank you very much.

  Hello
  I solved the problem. The answer was staring face heres so my solution for someone who has had similar problems.
  I didn't dig up the old router that affects the 192.168.1.xx IP network and then connected my PC, connected my printer then connected printers user interface through the static IP address, I assigned earlier. Changed to automatic IP. Connected my new router (which assigns the IP addresses of 192.168.0.xx) to my PC and printer. Everything is now OK.
  Thank you.

• 1102w won't print via USB

  We have a 1102w currently used via USB.  It works perfectly with the macbook from my wife and my computer laptop windows 7.

  I have a macbook pro with the OSC v 10.9.5 and went through the routine to add printer, but when I print I can see that the document will print to the queue, the print queue empties but the printer does not print the document, the blue light flashes but no printing... any help in getting this problem would be greatly appreciated.

  Hi @richardskelt ,

  I see by your post that you can't print via a USB connection on the computer of 10.9, but you can print on the Macbook and the Windows 7 laptop. I will do my best to help you with this problem.

  Connect the printer directly to the Mac USB cable and run the updates Apple to install the printer.

  Verify that the correct driver for the printer name is listed.

  Click on the Apple menu, click System Preferences. Click on Printers & Scanners, highlight the name of the printer on the left side and right side of the screen it should show the name of the printer. (P1102w)

  If the full name of the printer is not correctly, delete and add the printer name back from the list. Click on the sign - to remove the driver and then click on the + sign to add the driver might have to drop-down list to select the name of the printer to add a click.

  

  

  Test the printer.

  If you're still having problems, follow these steps:

  Fix permissions of the drive on the Mac:

  Close all applications.

  In the Apple menu, click OK, click Applications, and then click utilities.

  Double-click disk utility.

  Highlight your hard drive / partition on the left.

  Click on check and then repair disk permissions.

  Restart the computer...

  Reset the printing system:

  Note: This will remove all printers in the print and Fax/Scan, any printer deleted can be re-added later by clicking the sign plus (+) symbol.

  Click the Apple icon, and then click System Preferences.

  Click on Printers & Scanners.

  Make a right click (or Ctrl + click) in the left white side panel, and then click Reset printing system.

  Click OK to confirm the reset.

  Type the name and the correct password.

  Click OK to reset the printing system.

  Then click on the + sign to add the driver, you may need to click the drop down menu to select the name of the printer, and then click the Add button.

  Test the printer again.

  If you need help, let me know.

  Good day!
  Thank you.

• printer via usb router two computers to access

  I have a Canon iP4300 printer connected to my router via a USB port. I am running Windows7 Home Premium (x 86 on my laptop (connected WIFI)) and Windows7 Home Premium (64-bit) on my office (LAN connected).

  The printer works fine from my laptop - it was the first to be connected to the printer.

  However, during one attempt of the same exact configuration of my desktop (again) - I get "the printer cannot be contacted over the network.
  I used the own methods windows for the installation of the printer and it was OK and went through the Setup without a hitch. It's only when I got to print a test page that nothing happened. On verification of the device in printers and devices that I noticed an exclamation point on this printer on execution of the troubleshooter, and were done with the above result.

  Don't know if this will help, but here is the report:
  Devices and printers

  Problems found
  CANON printer cannot be contacted over the network
  Contact your network administrator
  Problem with printer without current issue
  Any problems that have been checked without current issue
  CANON printer is not shared with the homegroup without current issue
  Printer paper is low or empty without current issue
  Printer toner is low or empty without current issue
  Printer has a paper jam now childless
  Printer driver requires update no current issue
  Printer is off without current issue
  A print job in the print queue is preventing another printing of f...             No current issue
  The print spooler service problems of print spooler service is not running without current issue
  CANON is not the default printer
  No current issue
  Problems found
  < printer="" canon="" cannot="" be="" contacted="" over="" the="" network                     ="" not="">
  Network problems may prevent the printer from printing.

  TCP/IP printer port
  Port name: CANNON
  Port number: 9100
   
  Contact your informational network administrator
  Windows cannot solve the problem. Please contact your network administrator.

  Problem with printer detected
  There could be problems with CANON. Windows will take additional steps to continue troubleshooting.

  Potential problems that have been verified - (show all 'Does not present edition')

  Details of detection

  Diagnostic information (network card)
   
  Network card diagnostics information:
    
  Network adapter driver to connect to the Local network information:

  Description...:
  Realtek PCIe GBE Family Controller
  Reference of the manufacturer.... : Realtek
  Provider of...: Realtek
  Version...: 7.45.516.2011
  INF file name... . : C:\Windows\INF\oem2.inf (NB: I also tried an inf file that is downloaded from the website of Canon via the driver file.)
  Date of the INF.... January 26, 2012 03:41:59
  Name of the section.... : RTL8168E.ndi hardware... ID: pci\ven_10ec & dev_8168 & rev_06
  Instance... state flags: 0x180200a
  Status code of Device Manager. . : 0
  IfType  . . . . . . . . . . . . : 6
  Type of physical support...: 0

  Network Diagnostics log
  File name: F2B2D1FB - 07B 5 - 43E2 - 8 d 15. 965B6653BE52 Diagnose.Admin.0.etl (it is a pirated copy of the .etl report).

  Other newspapers and Network Configuration
  File name: NetworkConfiguration.cab

  Publisher details...

  A question, I thought that can be a problem, is that two computers use the same port (9100) even if I started adding the printer, while the laptop was on and Windows seemed to correctly identify it.

  My setup real basis is:
  Canon of general
  Location: http://192.168.1.1:631/printers/CANON
  Model: Canon iP4300 (this changes a little when I used different drivers)
  NB: Don't know if this helps, but I can't change ' paper available:' default > no matter what I do with the printer preferences?
  Sharing is off
  Http://192.168.1.1:631/printers/CANON ports > Port TCP/IP Standard > Canon iP4300
  Security... I did all what I can in an attempt to make sure there is no robbery here.

  AND as stated above... it all works very well from the laptop.

  So, any suggestions?

  Hi Snapafun,

  Try the steps in this link, it worked for me.

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• HP Photosmart 7525 PC connect to the printer via the wired network

  I install the 1 desktop computer printer that connects my wireless router with a cable, ethernet and 3 wireless laptops.  My main pc is the office.  During installation, the only options are to connect wirelessly or via USB.   When I select USB, the installer said I can't use all the features by using the USB.  Is it possible to install the printer with my desktop computer connected to my router via an ethernet cable?

  jconti01 wrote:

  .....  Is it possible to install the printer with my desktop computer connected to my router via an ethernet cable?

  Hello

  The answer is YES, you can connect like the following picture:

  

  Please see the following document:

  http://h10032.www1.HP.com/CTG/manual/c00389927.PDF

  Kind regards.

• Connection to a printer via Bluetooth

  Hey all,.

  Is it possible to connect any device bluetooth compatible printer via the BlackBerry and print? It doesn't have to be complete documents with images etc. Looking forward to all the advice.

  Kind regards

  Schalk

  Check this thread.

  http://supportforums.BlackBerry.com/Rim/Board/message?board.ID=java_dev&message.ID=12143&query.ID=46...

• HP1100 LaserJet connected via USB windows 7

  I want to connect my old HP1100 laserjet to my new office, which has no port of aparallel.

  I bought a cable to connect it to a USB port, but the driver will install.  Went to the HP site, but they say just that the driver is in Windows 7.

  I tried "add a printer", but it still does not work.

  Help!

  Hello

  1. which edition of Windows 7 is installed?

  2. What is the exact error message you get when the installation of the driver fails?

  Follow the mentioned methods:

  Method 1:

  (a) resources for the resolution of the printer in Windows 7 problems:

   

  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  (b) printer in Windows problems:

   

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Method 2:

  I suggest you of Uninstall and reinstall the drivers for the printer and check for the issue.

  Refer to article.

  http://Windows.Microsoft.com/is-is/Windows7/find-and-install-printer-drivers

  Install a printer by using the compatibility mode of Windows Vista:

   

  1. install the drivers in Compatibility Mode

  2 1. Place the driver on the desktop installation file.

  3 2. Right click on the driver installation file and select Properties/Compatibility tab select the appropriate option (Windows Vista) from the list.

  4 3. Click apply/OK.

  5 4. Right-click on the file and select run as administrator to install.

  Now try to install the printer once more and check for the issue.

  I hope that the above information is useful!