Satellite L300 (PSLB8E) - after update BIOS no longer start

Similar Questions

• Satellite L300 - 26K - after update BIOS touchpad no longer works

  Hello

  as recommended by tempro, I have updated the BIOS to the version 2.1 to 2.2 (windows). After the reboot, incl. touchpad. doesn´t advice working. In the bios, touchpad is enabled in the system, it said unit works correctly. FN/F9 does no effect. Reinstall the synaptics - no effect - drivers still dead.

  Satellite L300 - 26K
  Using Vista 32-bit home

  How can I restore BIOS to 2.1 again? (if I try the V2.1 windows-bios utility he says that it is always installed - so I can't downgrade by this easy way)

  Please help - I need my laptop without external mouse (this works)

  your

  Oliver

  Post edited by: enigmo

  Hi enigmo,.

  I can t imagine this happening due to the update of the BIOS. Have you tried to reinstall Windows using the Toshiba Recovery disk?

  This BIOS downgrade is possible only to an authorized service. Technicians can install all versions because they have these special tools to do a downgrade.

  On the Toshiba site, you can find a list of them. Just give the guy and ask for it. They will help you! :)

• Satellite L300 - dead after update BIOS!

  Hello!
  I had a problem with Windows XP, so I decided to update the BIOS. After update, I got 3 lines of errors. After the reboot, nothing appears on the scree! I have toke off the power to the battery and the power cable for some time, I had taken only one cable, but still nothing! No beeps, some noise of hard/dvd disc on begging. Can someone advise?

  Thanks in advance!

  Thom

  Hey Buddy,

  It seems that the BIOS is damaged and it must be reflashed to an authorized service provider. This is a delicate procedure so these tools can t be downloaded and are only available for the FSA. On the Toshiba site, you can find a list of all FSA. Simply contact the closest in the country and ask for help. Guys will help you best possible
  However, this forum can help you:
  www.theeldergeek.com/forum/index.php?showtopic=21209

• Satellite L - after update BIOS no longer start

  I just got an email saying that there was an update of the BIOS for my laptop. He began to install but my computer turned off and will not start back up
  Help, please!

  The update was: ACPI Flash BIOS version 1.90 for Sam/Sat Pro L355D/L305D (PSLE0U, PSLC0/1U)

  Nice to know, but the situation is clear.
  Something went wrong during the process of updating the BIOS and module ROM was not properly flashed.

  Only the ASP can help you mate
  So, don t waste time and get in touch with your country guys!

  See you soon

• Satellite Pro L300: BSOD after updating BIOS

  Hello

  After updating the Bios of the Satellite Pro L300, windows will not start!
  His show the blue screen of death!

  What can I do?

  Hello

  You are able to access the BIOS settings?
  I m not very well why this BSOD appears, but eventually the SATA mode settings have been changed after the BIOS update

  Usually the SATA mode must be on AHCI if the SATA drivers are installed.
  But if the SATA drivers are not included the SATA mode must be set to compatible.

  Please check this!

  In addition, you could set the BIOS default settings and may try to start the computer again.

• Satellite A210-199 - after updating BIOS only seeing yellow on

  Hi all, help is needed.

  After a BIOS updated with the help of Toshiba TEMPRO laptop Satellite A210-199 stopped working. The updated spent normally, but when it was turned off is more responsible. All this time the yellow indicator Burns power only. In a few minutes a laptop trying overloaded, but has no outside effect and so constantly.

  How is it possible to correct?

  Hello

  Well, it seems that the BIOS update has failed or something else. Maybe the ROM module must be reflashed by a technician of the laptop.

  But you can try this workaround first:
  Remove the battery and the AC adapter and wait an hour. Then reconnect both devices and try to start the laptop.

  If it doesn t work on the Toshiba site, you can search for nearest authorized maintainer:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  Good luck!

• Re: Satellite L300-11V - updated after the BIOS no longer start

  Hi guys, I've updated my BIOS today with 'InsydeFlash' with nothing open and everything looked perfect, said the program was a success and restarted.

  Now the laptop looks like its broke, it lights up but nothing. However, it tries to read the CD in the status bar that resembles his tent to recover himself. Any ideas? The problem is that it's barely out of warranty

  Hello!

  Akuma may be good but try this workaround too:
  Remove the battery and the AC adapter. Wait an hour and after that connect the two devices again. Now, you can try to restart the laptop.

  If it doesn t work it seems that, during the BIOS update something goes wrong and the module ROM needs to be reflashed. But it is possible to an authorized service provider

  Good bye

• Satellite A500-13W - after update BIOS the FN buttons do not work

  Yesterday I updated my Bios of my laptop to 1.50. After that the FN buttons no longer works. Can someone help me? ^ ^

  Sorry for my bad English

  Hello

  You have installed the correct version of the BIOS of your laptop?

  Features of FN buttons are normally not depending on the version of the BIOS. So, you need Toshiba value added Package and utility tools to Support Flash Cards. Then I recommend to reinstall two of them.

  You can download it here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  Remove all older versions first. Reboot then install VAP and finally Flash Cards Support utility.

• Satellite Pro 4270: after update BIOS CPU speed at 250 MHz

  Welcome.

  I have upgraded the BIOS to version 2.7 (downloaded on toshiba website) in Satellite Pro 4270 and after her, my bus speed decrease to 250 MHz, so now I have Celeron 250 MHz instead of 500 MHz. You have some suggestions? Where can I find the old version of the BIOS in v2.7?
  Thank you

  HI Artur,

  Unfortunately, it is not possible to download an older version of BIOS on yout laptop since the BIOS update procedure is written to test later versions pre-installed and not too write.

  You will need to take your laptop to a Service partner certified to have a previous version of the BIOS re-installed.

  Kind regards

• Satellite C55 - Has - after update BIOS fan turns faster

  Hello

  I have been informed by Toshiba application this new version of the BIOS is available, I confirmed BIOS and it has been updated. Now I have the problem. Cooling fan runs faster than before and it is very annoying.
  Find old versions of BIOS somewhere and roll back? I didn't need it if it does not work properly.

  Now I have version 1.40. Y at - it a solution for this new version?

  Message was edited: assignment has been translated

  Driver Toshiba UE page provides only the latest version of the BIOS.
  In addition, the BIOS downgrade isn't possible using the update to the BIOS of win-bases.
  To downgrade the BIOS Toshiba unit, you will need to use the traditional method of updating the BIOS that requires a special version of BIOS. It is available only for the authorized service provider.

  On the other hand, it must be a good reason, why the cooling module run faster.
  Perhaps that the cooling method has been improved again BIOS just to make sure that the internal parts would be properly cooled.

  It s just a guess but I think it makes sense

  By the way: after each update of the BIOS, you must load the BIOS default settings and should save the changes. If you haven t done this in the past, it doesn't

• Satellite L350D - crash after update BIOS?

  Hey all.

  Put windows XP on my Satellite L350D, worked well, has all the drivers etc. and works perfectly. Returned on the toshiba site and saw there is an update of the BIOS for it, then downloaded and says to install. To halfway through she turned off the laptop (thin power supply and had a full battery, so must have been updating).

  Now it will not boot up what so ever. The power light turns on but nothing else works.

  Im guessing that he wiped or corrupted BIOS, is there any fix for this, I can refer to toshiba or am I out of luck?

  Hello

  The failure of the Bios is one of the most painful problem in this forum. Too many discussions on the failure of the bios posted and typical response is to contact the ASP. Read this, may be useful for you

  http://www.theeldergeek.com/forum/index.php?showtopic=21209

• Touchpad no longer works after update BIOS on Satellite A500-1GL

  Hello world

  I just bought my laptop Satellite A500-1GL today. I started at the top and plays a bit (nothing serious). The touchpad worked very well at the moment.

  Then I discovered this tool to update the material and the update of the BIOS that worked without any problems. After I restarted the laptop, BIOS, loaded the default values of the installation and recorded.
  After that Windows 7 (x 64) started the touchpad no longer works...

  I downloaded the driver here and installed again once, still does not. I went into the BIOS, disabled the touchpad (I thought that maybe it's a bug...) and started again. It still does not...

  I enabled it again in the BIOS, tried to push the function + F9, but it still does not... Finally, I used the recovery and installed a Windows 7 costs.
  But unfortunately it still doesn't.

  Now, I'm out of ideas, can anyone help?
  Is there a chance to get the older version of BIOS to downgrade it?

  Thanks in advance ;)

  Hello

  It seems strange that after update Bios touchpad no longer works.

  > Is there a chance to get the older version of BIOS to downgrade it?

  To be honest, I don't know where to find. In any case, do a search on Google. Perhaps, other users of the forum can give you a link to download.
  The downgrade of the Bios is riskier upgrade procedure. So, be careful the next time...
  Advice for the future; Do not touch the running system.

  Good luck!

• Satellite Pro A300 (PSAG9E) - after updating BIOS Windows will not start

  Restart went well after update BIOS and Windows XP logo appears loads for a few seconds then a beep and restart - last good known or start Windows normally same effect.
  Reboot back to start - this is a new laptop - using the BIOS of Toshiba s official download site.

  Quite annoyed to try to find a way to upgrade or downgrade the BIOS.
  Took battery and RAM to see if I can delete it?

  Any ideas anyone?

  I think you mean BIOS * update * and do not upgrade ;)
  An upgrade is not possible

  However, you can try to remove the battery and the AC adapter and wait an hour. After that, reconnect the battery and the AC adapter and try to start Windows.
  Moreover I would load the default settings in the BIOS before starting Windows.

  If it doesn't work, it seems that your ROM module needs to be reflashed. In this case an ASP can help you.

• Installing WXP on Satellite L300 (PSLB8E)

  Hello

  I have a Satellite L300 (PSLB8E) laptop computer and I want to install Windows XP, but unfortunately, I still get an error message after you start the XP CD (XP Setup has encountered a problem, the Setup will leave...)

  Is there a solution?

  You use the Microsoft disk to install Windows XP? Then you need the SATA drivers to install in AHCI mode or the consistent value in the BIOS but so will lose some system performance.
  In the Forum are already a large number of discussions on this subject, in order to check the threads here.
  And take a look at this: http://195.182.196.33/kb0/TSB8602DB0001R01.htm

  However, it could also be that the CD is noisy or something else. Try another disc.

• Satellite L300-PSLB8E - screen becomes all white and the laptop freezes

  Hello

  I have a Toshiba Satellite L300 PSLB8E. I initially bought with Windows Vista already installed on it. After a few years, I changed the operating system Windows 7 Ultimate. I installed the display and all the other necessary drivers (that is, sound, network, etc.).

  After I installed Windows 7, when I use the laptop for a while, the screen becomes all white and the laptop hangs. This happens spontaneously. Sometimes, in less than 10 minutes and other times that it can work perfectly for hours. I checked for loose batteries and other components, but everything seems fine.

  Physical damage only that there is a tiny crack on the screen in the bottom right of the screen. The operating system is not good? If I put windows Vista back as it was?

  Please advise and help understand me what the problem is with the laptop.

  Until we start discussion can you tell me what you do when this happen?
  Hard stop and restart?
  Is everything OK again when you do?

  It is not easy to say what exactly is the problem, but I put t think there is problem with OS and preinstalled display driver. A long time ago I installed Win7 Home Premium on friends L300 and it works perfectly.

  What you can try is to use the external monitor for a while and see if everything works well. If so, there is no problem with the operating system, drivers or graphics card. It may be that the display problem.