Satellite A210-199 - after updating BIOS only seeing yellow on

Similar Questions

• Satellite A210-16f - after the BIOS update pops up a window with password

  Hello

  I tried to update the BIOS on my Toshiba Satellite A210. I downloaded an update from the official site of Toshiba, and then I did everything according to the instructions.
  I've updated the BIOS under Windows.
  Update at the end, a massage "updated successfully" appeared and I just need turn on the computer again.
  So I did, and there was a problem.

  When I turn on my computer now, it shows me a blue window with a password. I don't know password.
  Maybe you know how to disable the password or you know some passwords for Toshiba which corresponding?

  Toshiba doesn t have a sort of universal password, and unfortunately, no one here can help you with this problem.
  I just hope that you have downloaded the good BIOS upgrade for your laptop model.

  The password can be removed by the Toshiba service provider. They can do it in 15 minutes.
  Sorry, but buddy I'm afraid there is nothing you can do about it.

• Equium A210-1AS - after update BIOS screen no longer works

  I tried to find the same problem but impossible.

  I had to reinstall Windows Vista after mistakes with programs (recovery was useless so install fress was necessary) and everything worked fine. I downloaded all the drivers and updates section of drivers Toshiba, I installed the ATI graphics driver, then update the BIOS.
  While the closed laptop, now when I turn it on, the fan on the works of graphics card, battery, power and load turns on but the screen remains off (not illuminated). I tried an external monitor and the same problem again. As the screen worked fine until the update im guessing its something that the BIOS has done, or the graphics update.

  TOSHIBA SATELLITE A210 - 1AS
  PSAFJE
  -AMD Turion 64 X 2 Dual-Core Mobile Technology TL-58-
  Genuine Windows® Vista® Home Premium edition-
  DVD Super Multi (Double Layer) drive-
  2 048 (1 024 + 1 024) MB of RAM DDR2 (667 MHz)-
  15.4 "TFT display 1280 x 800

  Thanks to all who can help.

  To me, it sounds like the update of the BIOS's not on your laptop. If the BIOS update fails more often than computer start doesn t more you can see anything on the screen but you can hear the fan, etc.

  In any case, you can try this workaround: remove the battery and the AC adapter. Wait an hour and then reconnect the two devices. Now try to start Notepad and hope this works ;)

  If it doesn't work, you should contact the nearest authorized service provider. Technicians can try to reflash the ROM module

  Good luck!

• Satellite L300 - dead after update BIOS!

  Hello!
  I had a problem with Windows XP, so I decided to update the BIOS. After update, I got 3 lines of errors. After the reboot, nothing appears on the scree! I have toke off the power to the battery and the power cable for some time, I had taken only one cable, but still nothing! No beeps, some noise of hard/dvd disc on begging. Can someone advise?

  Thanks in advance!

  Thom

  Hey Buddy,

  It seems that the BIOS is damaged and it must be reflashed to an authorized service provider. This is a delicate procedure so these tools can t be downloaded and are only available for the FSA. On the Toshiba site, you can find a list of all FSA. Simply contact the closest in the country and ask for help. Guys will help you best possible
  However, this forum can help you:
  www.theeldergeek.com/forum/index.php?showtopic=21209

• Re: Satellite A210 dead after that BIOS crashed

  Someone please help!

  During BIOS update computer laptop (toshiba satellite a210) spontaneously restarted.
  As the record on the controller was not performed (if I understand correctly) is now a laptop is not included.

  Thanks in advance for any help.

  Hi mate

  I m afraid. I have bad news for you.
  The laptop needs a help of ASP.
  The module ROM BIOS has to be flashed again and this can be done by ASP in your country. The technician would use a disc of crisis of BIOS that allows to get the laptop back to life.

• Satellite L300 (PSLB8E) - after update BIOS no longer start

  Hello..
  Please, help me to overcome this problem.

  I downloaded the latest BIOS for my Satellite L300 PSLB8E. The previous BIOS was 1.90 but I was facing some nework of error so I thought to upgrade the BIOS can help solve. I have download a new BIOS which is the exe 2.10, its installed successfully, and then shut down, but never started again. I tried to start it several times. I tried all the keys. I don't see a power led and two battery light.

  I don't know what to do now. I have a recovery disk but it also does not work. I'm stuck. II had built a bunch of emails to answer that I am lost now.

  Please help me someone.

  Hi dhaval2000in,

  Unfortunately, I think the case is clear: something was wrong because the BIOS update and now your laptop can start t more :(

  The Toshiba Recovery disk will not help you because it doesn't contain any BIOS programs it contains only an image of recovery of Windows with all the drivers and flashing tools.

  In my opinion, please contact an authorized service provider in your country to get rid of it because the guys do reflash ROM. module
  I m that you can clarify this issue with the technicians and then you can use your laptop again :)

• Satellite L300 - 26K - after update BIOS touchpad no longer works

  Hello

  as recommended by tempro, I have updated the BIOS to the version 2.1 to 2.2 (windows). After the reboot, incl. touchpad. doesn´t advice working. In the bios, touchpad is enabled in the system, it said unit works correctly. FN/F9 does no effect. Reinstall the synaptics - no effect - drivers still dead.

  Satellite L300 - 26K
  Using Vista 32-bit home

  How can I restore BIOS to 2.1 again? (if I try the V2.1 windows-bios utility he says that it is always installed - so I can't downgrade by this easy way)

  Please help - I need my laptop without external mouse (this works)

  your

  Oliver

  Post edited by: enigmo

  Hi enigmo,.

  I can t imagine this happening due to the update of the BIOS. Have you tried to reinstall Windows using the Toshiba Recovery disk?

  This BIOS downgrade is possible only to an authorized service. Technicians can install all versions because they have these special tools to do a downgrade.

  On the Toshiba site, you can find a list of them. Just give the guy and ask for it. They will help you! :)

• Satellite C55 - Has - after update BIOS fan turns faster

  Hello

  I have been informed by Toshiba application this new version of the BIOS is available, I confirmed BIOS and it has been updated. Now I have the problem. Cooling fan runs faster than before and it is very annoying.
  Find old versions of BIOS somewhere and roll back? I didn't need it if it does not work properly.

  Now I have version 1.40. Y at - it a solution for this new version?

  Message was edited: assignment has been translated

  Driver Toshiba UE page provides only the latest version of the BIOS.
  In addition, the BIOS downgrade isn't possible using the update to the BIOS of win-bases.
  To downgrade the BIOS Toshiba unit, you will need to use the traditional method of updating the BIOS that requires a special version of BIOS. It is available only for the authorized service provider.

  On the other hand, it must be a good reason, why the cooling module run faster.
  Perhaps that the cooling method has been improved again BIOS just to make sure that the internal parts would be properly cooled.

  It s just a guess but I think it makes sense

  By the way: after each update of the BIOS, you must load the BIOS default settings and should save the changes. If you haven t done this in the past, it doesn't

• Satellite Pro 4270: after update BIOS CPU speed at 250 MHz

  Welcome.

  I have upgraded the BIOS to version 2.7 (downloaded on toshiba website) in Satellite Pro 4270 and after her, my bus speed decrease to 250 MHz, so now I have Celeron 250 MHz instead of 500 MHz. You have some suggestions? Where can I find the old version of the BIOS in v2.7?
  Thank you

  HI Artur,

  Unfortunately, it is not possible to download an older version of BIOS on yout laptop since the BIOS update procedure is written to test later versions pre-installed and not too write.

  You will need to take your laptop to a Service partner certified to have a previous version of the BIOS re-installed.

  Kind regards

• Satellite A500-13W - after update BIOS the FN buttons do not work

  Yesterday I updated my Bios of my laptop to 1.50. After that the FN buttons no longer works. Can someone help me? ^ ^

  Sorry for my bad English

  Hello

  You have installed the correct version of the BIOS of your laptop?

  Features of FN buttons are normally not depending on the version of the BIOS. So, you need Toshiba value added Package and utility tools to Support Flash Cards. Then I recommend to reinstall two of them.

  You can download it here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  Remove all older versions first. Reboot then install VAP and finally Flash Cards Support utility.

• Satellite L350D - crash after update BIOS?

  Hey all.

  Put windows XP on my Satellite L350D, worked well, has all the drivers etc. and works perfectly. Returned on the toshiba site and saw there is an update of the BIOS for it, then downloaded and says to install. To halfway through she turned off the laptop (thin power supply and had a full battery, so must have been updating).

  Now it will not boot up what so ever. The power light turns on but nothing else works.

  Im guessing that he wiped or corrupted BIOS, is there any fix for this, I can refer to toshiba or am I out of luck?

  Hello

  The failure of the Bios is one of the most painful problem in this forum. Too many discussions on the failure of the bios posted and typical response is to contact the ASP. Read this, may be useful for you

  http://www.theeldergeek.com/forum/index.php?showtopic=21209

• Satellite A210 - 1BW PSAELE - update BIOS crash

  Hello

  I have a problem with my A210-1BW
  I did last night a Bios Update, but winphlash hangs up during the update. I waited about 20 Minutes, but nothing happened.

  Then I killed the WinPhlash process and try again to update, but then get an error message. I try to restart and get the white screen. I turned off the laptop and close again on it, but now there are nothing but black screen.

  I already try the drive of crisis of Phoenix with the 2.0 version of the homepage of Toshiba BIOS, but not worked.
  Anyone know what I can try?

  And can someone send me to try an older version of Bios and then on the home page?

  Thanks for your help.

  Good bye
  MaximL

  (Sorry for my bad English, I'm German)

  The system will still boot from the CD?

  In the case where it doesn't start at all, there is little you can do. Re-flashing with the cd of the crisis is according to my knowledge the last possibility, otherwise you should better communicate with Toshiba service center. Maybe they can help you or fix the laptop (replacing the BIOS chip).

• Satellite Pro A300 (PSAG9E) - after updating BIOS Windows will not start

  Restart went well after update BIOS and Windows XP logo appears loads for a few seconds then a beep and restart - last good known or start Windows normally same effect.
  Reboot back to start - this is a new laptop - using the BIOS of Toshiba s official download site.

  Quite annoyed to try to find a way to upgrade or downgrade the BIOS.
  Took battery and RAM to see if I can delete it?

  Any ideas anyone?

  I think you mean BIOS * update * and do not upgrade ;)
  An upgrade is not possible

  However, you can try to remove the battery and the AC adapter and wait an hour. After that, reconnect the battery and the AC adapter and try to start Windows.
  Moreover I would load the default settings in the BIOS before starting Windows.

  If it doesn't work, it seems that your ROM module needs to be reflashed. In this case an ASP can help you.

• Touchpad no longer works after update BIOS on Satellite A500-1GL

  Hello world

  I just bought my laptop Satellite A500-1GL today. I started at the top and plays a bit (nothing serious). The touchpad worked very well at the moment.

  Then I discovered this tool to update the material and the update of the BIOS that worked without any problems. After I restarted the laptop, BIOS, loaded the default values of the installation and recorded.
  After that Windows 7 (x 64) started the touchpad no longer works...

  I downloaded the driver here and installed again once, still does not. I went into the BIOS, disabled the touchpad (I thought that maybe it's a bug...) and started again. It still does not...

  I enabled it again in the BIOS, tried to push the function + F9, but it still does not... Finally, I used the recovery and installed a Windows 7 costs.
  But unfortunately it still doesn't.

  Now, I'm out of ideas, can anyone help?
  Is there a chance to get the older version of BIOS to downgrade it?

  Thanks in advance ;)

  Hello

  It seems strange that after update Bios touchpad no longer works.

  > Is there a chance to get the older version of BIOS to downgrade it?

  To be honest, I don't know where to find. In any case, do a search on Google. Perhaps, other users of the forum can give you a link to download.
  The downgrade of the Bios is riskier upgrade procedure. So, be careful the next time...
  Advice for the future; Do not touch the running system.

  Good luck!

• Satellite A210-199: cannot communicate wirelessly with DreamBox 7020 s

  HY to all members and admins,

  I am newbee on TOSHIBA Satellite A210-199, and I have the following problems:

  (1) I can not connect with Wi - Fi, with my Satellite Receiver based LINUX DreamBox 7020 s:
  before & now with a HPnx9010 and a desktop running Windows XP SP2, I've been fave not no problem!

  With "Doctor Conectivity" - application, I have, in the log file, this:

  * Diagnosis results *.
  Ping option: Off
  How can I do this option: WE / permit?

  (2) even I recorded with my product I can't received updates TOSHIBA drivers!

  Thank you for to advance & regards better

  The Microsoft Vista operating system has been pre-installed on the Satellite A210-199. Am I wrong?
  You have turned off all firewalls? Check it!

  Regarding your connectivity doctor' application he is a tool of Toshiba ConfigFree.
  It s only a tool of diagnosis and you shouldn't t he use for the WLan configuration.

  I think you have to use zero configuration of Windows Vista WLan settings it s a Vista own function for WLan Access the WLan Vista settings configuration and check in the TCP/IP protocol properties, if all the settings are set to automatic.

  Regarding your update of the Toshiba driver;
  All the drivers are available on the European driver Toshiba page. If you need an update and then just check the driver page but I would follow these useful tips. never change to a system running, does that mean if your laptop works well, updates are not necessary.