Satellite P30 - cannot find Wireless Access Point

Similar Questions

• C4780 wireless printer cannot find the access point

  I have c4780 wireless printer.  It will print fine using the usb connection, but has never printed wireless.

  PC operating system is Windows Vista.  Wireless router is the linksys WRT54G.  The printer does not see the access point.  The security mode of the router is WPA Personal.  I have a unique SSID.  ISP is Timewarner Roadrunner.

  How do I get this to a wireless connection?

  Try this firmware update.

  In addition, sweat you are broadcasting your SSID and not using MAC filtering.

• Cannot find wireless devices. All-in-one - C309a - "HP printer cannot find your access point"

  Printer: C309a - I have trouble connecting the printer to my wireless network.

  RAN wireless configuration wizard: it ran for a long time but no device not returned.

  Wireles RAN Network Test report: Wireless on - PASS, Wireless - PASS, the name of the network (SSID) found - work FAIL.

  The wireless network Test report shows no IP address on the screen. under mask and default gateway are displayed also as 000.000.000.000

  I have reset to factory settings.

  Other devices took the 192.168.1.250 spot

  My router is visible SSID.

  This is a replacement C309a - my previous C309a - when I ran the test report my previous camera wireless network, said that the radio was not working, so I knew that based on previous posts, that the radio card died and to get a replacement printer. I hope it's a configuration problem and that the wireless on this replacement radio can still work.

  Thanks in advance.

  OK, radio seems OK.  What router are you using?  You've restarted the router by pulling its plug momentarily?

  If anything does not work, we will reset the printer: turn off the power.  Maintain the # and 9 keys while a few seconds after again.

• Launch of Lightroom 6 is not. error: "can't find the access point of the procedure _crtCreateSymbolicLinkW in the MSVCR110.dll dynamic link library.

  It says: "cannot find the access point of the procedure _crtCreateSymbolicLinkW in the MSVCR110.dll dynamic link library. What can I do? I have already uninstall and then reinstall the software...

  It is indeed a microsoft problem, check here:error "did not find the entry point _crtCreateSymbolicLinkW - Microsoft Community .

• Cannot connect by Satellite L300 wireless access point

  I have a new laptop L300 & I can't connect to the laptop to my wireless access point. I have an another mobile E-sytems with the same hardware Realtek RTL8187B & it connects without problems.

  The machine has the free two month Mcafee subscription & I have disabled all the protection incase that was causing the problem. I updated the driver for the wireless card & the bios on the Toshiba site, but nothing is.

  Can someone shed light on this problem because the laptop is only two weeks old?

  Thank you...

  Hello

  To connect the laptop to the WLan, it must ensure that everything is enabled and configured correctly.
  You should check these points:

  -activated the WLan with the WLan switch and the FN + F8
  -don t use any 3rd party config tools WLan if you use the WLan configuration options own Vista
  -for the first test WLan disable the security settings of the Wlan router
  -configure settings to laptop as good SSID and search for your wireless local area network
  -After that the laptop is connected to the WLan router, you can turn back the security settings (encryption, mac address filtering, firewall, etc.)

  Welcome them

• Card wireless INTEL PRO 2200 BG - don't find any wireless access point

  I just try to run internet with the internal PRO INTEL BG 2200 wireless card.
  The driver version is just updated to 9.0.4.39. The problem is, I can't find any wireless access point.

  I also use a D-Link card, with this card, I found the available access points. What could be the problem with the INTEL PRO card. I'm sitting right next to the router/hub.

  Also, I thought that I might need to activate the wireless with additional keys Fn function, but they do not work, I guess. Maybe I need a driver for this tool also. Do anyone know where I can find drivers to use the Fn keys?

  My system:
  TOSHIBA Tecra
  WINDOWS XP (SP 3)

  See also: The INTEL internet LAN works.

  > What could be the problem with the INTEL PRO card. I'm sitting right next to the router/hub.

  For me, it seems that the WiFi network is not enabled.
  Usually, you need to activate the WLan switch which is placed on the side of the laptop. Then, you'd see an active WLan led.
  If you n t see the light, then the WiFi network has not been activated.

  In addition, choose the WLAN using FN + F8!
  You can also activate the Wlan in Device Manager-> card Wlan-> properties-> Advanced tab.

  Good bye

• Unable to find the access point or use any device to all wireless to connect to my BEFSR41 v4.0

  Hi well the problem seems to be that whenever I try to use any type of device and try to connect using a wireless connection to my router, I can't find an access point or no signal at all of it, but when you use a wired connection, it works perfectly. For example, I'm trying to connect my Wii to the internet via a wireless connection, but I can't find any access point so that it can connect to. So I went to my router configuration and I didn't know what to do to allow a shown access point or wireless to all activity. Theres no wireless tab or whatever it is to install, so I didn't allow remote administration, but still I could not find an access point. I don't know if im just made bad or I need an update of the firmware (mine is currently 1.04.02) or what else. If the help would be nice

  BEFSR41 isn't a wireless router... It is wired.

• Use WAN connected airport Time Capsule as a wireless access point

  I had to replace a failed 4 Gen Time Capsule. I tried to install a new Gen 5 airport TimeCapsule via WAN and set up the airport to act as a wireless access point. It is installed in an area of my house with wireless coverage. In the network of AirPort Utility Mode section, I chose "extend a wireless network. The TC is restarted, I get an error message cannot find the intended wireless network.

  What I lack?

  "Extend a wireless network" is a parameter that is only used if the time Capsule need to connect to another router from Apple with the help of a Wi-Fi connection.

  You use Ethernet to connect, you must use the parameter to "create a wireless network. Use the same wireless network name and the same password as your "primary" router

• There is no communication between devices that are connected to the Linksys WAP4410N Wireless access point?

  Hi all

  I have deployed the new Linksys WAP4410N Wireless Access Point and it works fine. Laptop which is connected to the AP may be able to access the internet. It can communicate with AP and also the gateway IP (IP Router) but it is wireless devices are not able to communicate with each other. In the case of peripheral LAN can communicate with wireless devices. Cannot able to share files between wireless devices.

  Please help me solve this problem. Wat could be the problem here. Stage of Wat I have to take to eliminate this problem.

  Advance thanks.

  Thank you and best regards,

  Chandhuru.M

  Hi, my name is Eric Moyers. I am a network Support Engineer in the Cisco Small Business Support Center. Please use the Forums to Post community of Cisco.

  The title of security without thread/how do you have isolation set up wireless?

  Insulation wireless (SSID) on the inside must be disabled to allow the computers associated with the same SSID to see and transfer files between them wireless

  Thank you

  Eric Moyers. : | :. : | :.

  Cisco Small Business U.S. STAC Advanced Support Engineer

  CCNA, CCNA-wireless

  866-606-1866.

  Mon - Fri 09:00 - 18:00 (UTC - 05:00)

  * Please rate the Post so other will know when an answer has been found.

• Errror: The certificate chain was issued by an authority that is not approved. connecting to a wireless access point

  I can't understand the process of certificates, by connecting a pc wireless access point that is authenticated by the radius server, im keep having this error "the certificate chain was issued by an authority that is not approved." do I need to set a certificate on the pc?

  Hello

  1. What is the version of the operating system that you are using?

  2. What is the exact full error message?

  If you use Windows 7 follow the link below:

  http://Windows.Microsoft.com/en-us/Windows7/view-or-manage-your-certificates

  http://Windows.Microsoft.com/en-us/Windows7/certificates-frequently-asked-questions

  You can also contact your ISP for more information.

  Hope the above information is helpful.

• A WRT160N V3 can be used as wireless access point.

  I have an AT & T's broadband router.  A WRT160N is connected, so I now have Wireless N capabilities.  I have a second WRT160N I want to put in my living room as a point of access, so I can connect my BluRay player and video stream.  How can I configure the second WRT160N as access point?

  Thank you in advance,

  Andrew

  Topic 1. Yes, you can use your second WRT and put in place as a second access point to your network. First of all, unplug the second WRT to your network and wire a computer in one of its LAN ports. Open the web interface at http://192.168.1.1/ on the main configuration page, change the address LAN IP of 192.168.1.1 to 192.168.1.2 and disable the DHCP server. Save the settings. Unplug the computer and connect the cable to the first router on one of the second router's LAN ports. Do not use the internet port of the second router! Now you can use the wireless access point in the second router as access point additional for your network.

  For a wireless roaming the two Wrds with identical wireless settings (SSID, wireless security, etc.) and don't forget to enable the SSID broadcast. Only the channel assignments should be different. Different channels spaced at least 5 avoids duplication of canals. Now your laptop can connect to your network via either WRT and internet through the first WRT. It must also be able to move between the two Wrds without losing the connection.

  Re 2. Because the WRT160N has only the ethernet 10/100 ports a CAT5e cable should do. Of course, you can consider getting a better cable, for example a cat6 for future enhancements to your network. It depends on how much effort it is necessary to replace the cable later if you decide to go for gigabit ethernet on your local network.

• The WRT600N can connect to a wireless access point?

  I installed Windows 7 on my desktop and I was not able to install all types of Linksys wireless adapters.  I decided that linking an my WRT600N wireless access point in the other room and hardwireing the office to the access point, would be a good idea.  I'm probably going to connect it to a Net WTG624 Gear, which is capable of acting as an access point and you connect to another router.  The question is, can the WRT600N you connect to and use the internet and the local access and, ultimately, on the Office of cable?  I feel that it is one of the most stupid questions, I ask myself here again, but I'm not sure.

  EDIT: I'm sure it's called Wireless Bridge.

  Thank you

  Zach

  Hello Zach,

  The WRT600N can connect at the point of access, and vice-versa. I have a WRT600N home and have the same model of NetGear as access point (what are the chances?) and it works fine, although I do miss the 5 GHz as the Access Point is only 2.4 Ghz 802.11 g Standard.

  I hope this helps!

• configuration cisco air-ap1142n-a-k9 problem wpa2 wireless access point

  HI people,

  I am brand new to Cisco Wireless, just that I bought new wireless access point air-ap1142n-a-k9 cisco, try to configure the configuration of wpa2 for security reason, but impossible to configure in any mode security. So my AP is currently no security / encryption mode.

  Could someone can help and suggest me I will appreciate if I get all documents, so the security problem can be solved.

  Concerning

  Sanjeev

  OK great

  ----------------------------------------------------------------------------------------------------------------------

  Be sure to note the correct answer and mark the thread as answered

• Beginner needs help with Aironet 1131 G Wireless Access Point

  I have a new Cisco Aironet 1131 G wireless access point.  It takes an IP address and I can ping this address.  However, I can't access it via the graphical user interface based on the web or the CLI.  I preformed reset.  Any suggestions would be greatly appreciated.

  Thank you.

  Hello

  I can't access that means? you are not able to go to the CONFIG T of the CLI prompt? and if you are in the same subnet as the AP, are you not able to open to the top of the GUI? If you are not able to then, with the command 'show version' on the AP CLI and see if your image is "RCVKW8". If so you will need to convert the same IOS using the method below.

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap22-trouble.html#wp1038660

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• After running Thinkvantage System Update, unable to connect the wireless access point

  I've recently performed Thinkvantage System update for updating various programs/drivers on my T61p.  I've updated the V5.12 access connections.  In addition to this I was required to update driver V1.52 power management and functionality of the shortcut key for

  V2.10.0002 (two of them were the most recent available).

  After these updates, I can connect is no longer to any access point wireless that worked before this update.  I have tried to reinstall earlier versions of Access Connections, but still couldn't connect to wireless access points.

  ANY help would be appreciated.

  OK, problem solved.  I found that when I ran last weekend system update downloaded and installed an incorrect driver for my wireless hardware.  I installed the correct driver and now the connection to a wireless access point works.

  Certainly, I don't understand how/why not update system would be to download and install an incorrect driver.  VERY FRUSTRANT and TEDIOUS!