Satellite P300-156 - screen will not come

Similar Questions

• Satellite L450D-13U - screen will not come

  I have a laptop Toshiba Satellite L450D-13U with 2 GB of RAM and no hard drive.
  My problem is that the display does not illuminate. I tried all the well known stuff and stuff like taking the battery, power down etc button but nothing seems to work.

  Can't even connect to an external monitor. Is there a part that I could change what can help this problem?

  Thank you very much

  Without any serious diagnosis, it is not easy to say what the problem is. Perhaps is faulty display.
  By the way: what happening exactly when you press button walk / stop?

• Satellite L555-10N screen will not shut down after 10 minutes of non-use

  Hello

  I recently acquired a laptop Satellite L555-10N, which so far has proved to be a good choice.
  I have a little problem, however:

  In the preferences of my energy, I put the time during which the screen should turn off, 10 minutes, if the laptop is not in use.
  Although this worked well for the last few days and weeks, the display now will be not closed at all.
  I did not change the BIOS or driver or whatever.

  I remember to change some preferences in the configuration ecoUtility to enable.
  At that time, I received a message that preferences should be modified to enable the functionality and I agreed.

  I could not notice any changes have been made, but from there, the screen off more.
  I would appreciate your help!

  Thank you!

  Hello

  What operating system you are using?
  For Vista and Windows 7, I founded a good article on Windows power management settings:
  http://APS2.toshiba-tro.de/KB0/HTD84026Q0000R01.htm

  In addition, you can change the settings for each profile. This means that you should choose turn it off the display function for this power profile that you use or all profiles, if I used all of them.

  Check this box!

• Computer is on, but screen will not come. Black screen of death?

  When I turn on my laptop hp... nothing happens. The lights on the keyboard will light up, and the fan runs for about five seconds... but the screen remains black. I don't know how to get to safe mode or anything like that since the custom of the screen lights up. All I want to do is turn it on long enough to retrieve a piece of paper and put it on another USB key. PLZ HELPPPP!

  Hello

  Specific hardware problem. Check with a computer store real and/or HP support.

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  I hope this helps.

• I updated adobe and now windows vista will not come to the top!

  I was doing something that requires adobe 9 or higher, so I updated to 10. Now my main screen will not come to the top. I can't do all the suggestions for troubleshooting because I can't get to my computer at all.  I validated and it says windows Pascal more send activationsetc. and I can't update because I can't.

  Try to start in safe mode (press F8 immediately and repeatedly after Power Up Self Test and before Windows starts) and uninstall Adobe Reader X.  Then try to restart normally.

• Re: Satellite P300-156: keyboard freezes touch touchpad - mic is not w

  Hello

  I installed Windows 8 on my satellite P300-156 and now I have a big problem.
  My keyboard crashes when you touch the touch pad. In addition, the microphone does not work when the Windows Device Manager indicates that it is ok.

  There is no windows driver for this laptop 8...

  There are no drivers for the laptop because it isn't win 8 supported series.
  But even if there is no Win 8 drivers, the system should not freeze affecting the touchpad module.

  However, the Synaptics touchpad driver for Win 7 or 8 to win can be downloaded from Synaptics page.
  Recommend check it out!

• Sound on Satellite P300-156 problems

  I bought a Satellite P300-156 1 year, mainly because he looked good and had Dolby Sound Room. However, I discovered not long after the purchase that he had no Dolby installed - so I tried to download the new drivers on the Toshiba site. They worked and gave me the SmartAudio app to activate the Dolby Virtual Speaker and Headphone Dolby of Dolby Sound Room. -The volume varies, as someone who has a hold on the volume dial. Not only when songs get more coins, but even just when someone speaks.

  This is crazy - and very annoying - and disappointing given the speakers harmon/kardon give amazing clarity. 3 driver updates later - still the same problem. Heard about people with the new P500 have the same problem - please does anyone have a solution? I got the problem under Vista 32 bit and now the same thing under 7 64-bit. It's a Conexant driver.

  The problem does not occur under the headphones/external speakers.

  Thank you.

  Hello

  If I understand this problem, that happened after the driver installation, and after activating the Dolby Sound Room.

  In Control Panel-> Audio Smart-> Audio second tab management, you will find a few options.
  The mode clasic has been marked.

  Uncheck this box and go to the Multi flow modes and configure it.

  I m not very well what settings you need to enable or disable because I m not P300 owner, but you should play around with these options and try different settings.

• Satellite P300 - 156 Windows 7 Crash problem

  Hello
  I have the Toshiba Satellite P300 - 156 PSPC4E, model and I've had this laptop for a couple of years now.
  Before installing windows 7, I got the default Windows Vista installed and it worked fine.
  Now since installing windows 7, no matter WHAT game I try and play just causes the cell to go black screen and turn off after about 5-10 minutes of play.
  I thought that this was due to an overheating problem... so I opened the laptop and cleaned all that and then put it back together again.
  (YES I checked all the wires are back where they should be and all the components are working properly)
  It did not work.
  Then I tried updating all my drivers and software ect.
  Still nothing.
  I searched on through pages and pages of search results for the same problems with Windows 7 and the game crashing... but nobody seems to know how to fix it.
  I thought it was just windows 7, but I re installed windows vista and it's always done the same thing on there now.
  I tried to install all the drivers of the model for this laptop toshibas site and not luck.
  My windows vista and windows 7 are two authentic copies.

  All the hardware is functioning normally (as far as im aware) and I really don't see what can cause this problem.

  If someone could give me some advice on what to do it would be greatly appreciated.

  Thank you

  Hello

  Which driver you use display? I m P300 owner but not on my A300, I had a similar problem that the laptop has crashed during a game. It seems that the reason was a 3rd party driver or let's say the driver of the manufacturing of the graphics chip directly. I think that because they are not prétestées on the cell and causing overheating

  So I recommend you to install the latest driver of display on the Toshiba site.

  Finally and above all what version of Windows 7 (32 or 64-bit), you have installed and what version of BIOS?
  From Toshiba Web site also shows the new BIOS versions and several versions 32 bit and 64 bit OS. Maybe you have to day/edit, who knows?

• Satellite P300-156 - and the button Return give the same values

  Hello

  I have a satellite P300-156, and it has a numeric keypad.
  I have problems because the Enter key and the Return key give the same values. I believe that it is incorrect.
  Can anyone help.

  Key on the numeric keypad should give an input it does.
  the Enter key on the main keyboard should give a carriage return value, but it gives an input value.

  Usually this does not cause a problem, but with software like photo shop that makes the distinction between a carriage return and a hard fall it does not work.

  Can someone help me please

  Thank you

  Hello

  To my eyes the entry and return keys are the same keys that provides the same functionality.
  I really put t know why you believe that there is something not right

  By the way; Check if you are using the latest version of the BIOS!

• Satellite P300-156 won't start or by MAIL

  Hello

  I have a Satellite P300-156 I bought a few months as damaged. The screen has been damaged and the case slightly cracked. I replaced the screen and hard drive and main card seems to have no physical damage. I've been running this system for 3 months now without any problem but, today, for some reason, it won't start or even POST. It powers on and the CPU fan starts to turn then stops and does nothing. No display (I tried external). CD player works. No beeps.

  I tried reinstalling RAM even open completely and reinstalling all connections, nothing done. Does anyone have an idea what component is gone? (CPU/GPU/RAM)

  Any help would be greatly appreciated

  Thank you

  Did you update the BIOS or something?
  For me, this is a normal behavior when the BIOS chip is faulty.

• Can't connect, connection startup screen will not respond to mouse clicks or keyboard

  I do not have a DVD to boot from. I use a laptop (Acer Aspire 5610). The keyboard and mouse are internal.  Any suggestions at all? I tried the Safe Mode, Mode safe mode with guests hoping to type rstrul.exe, but never had the guest. He went directly to the display of connection with my daughter and my icons. I have added no new material.

  Separated from the:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/cant-login-login-splash-screen-will-not-respond-to/54da4727-b98c-436a-8D82-f31c3355f5fd

  Have you shot inadvertently carpet of mouse/keyboard. This can happen through the Fn key on some laptop models. Find the picture on the key Fn, should give a clue.

  You can borrow or buy a usb KB and mouse that you would at least pass by troubleshooting?

  Tricky

• My Dell is power saving mode and will not come out

  My Dell is power saving mode and will not come out? Any suggestions? I can't get anything else than a screen that says it is in power save mode and press a key or move the mouse. No one who does nothing. Don't disconnect.

  Hi Ma32206,

  Monitors Dell will automatically mode energy saving after a predetermined time amount when the computer is idle. The Dell monitor will go completely black, rather than display a screen saver. This allows your monitor to essentially turn off until it takes again.

  A. Press any key on the keyboard or move the mouse. Either will automatically turn off the power saving mode. Alternatively, you can press the power button on your Dell computer tower or laptop.

  B. press one button a second time if the monitor goes power saving in standby mode. Standby mode allows the screen saver appears.

  Bindu R - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows 7 splash screen will not change after the vista update

  After updating vista 32 bit to windows 7 32 bits, the splash screen will not change and he showed the vista boot. I read a lot of forum and the web page, but this solution:

  «.. . the dummies and bad start screen for Windows 7 is due to the locale entry in the startup folder, which could not be set when editing or rebuilding the BCD. When the locale is not found, Windows boot loader doesn't know what local startup folder to look for the animated bootscreen. Thus, in order to fix the boot screen so that the splash screen can be re-established, restored or reset to original animated Windows 7 boot screen, just run one of the following commands at the prompt with administrator rights:

  bcdedit/set {current} settings regional en-US

  or

  BCDboot % WinDir % / l en

  Change the US to the language version of Windows 7 installed, as ja - JP, en - us, es - ARE, pt - BR, zh - CN, zh - TW, fr - FR, fi - FI and etc.

  Restart the computer after running the command to see the new boot UI (user interface) be used again. To check if the locale has been entered properly, just run the bceedit command in the command prompt that is running as an administrator... »

  not solved my problem and also know for many users... after updating vista in windows 7 splash screen stay the same...

  Thanks for your help
  Hispanico hispanico

  Hi hispanico,

  Thank you for visiting Microsoft Answers.

  I suggest you do a repair from WinRE (Windows Recovery Environment) system using a Windows 7 installation disc. Follow these steps:

  1. turn on your computer, insert the Windows installation DVD, and then restart your computer.

  2. Press any key when prompted to do so and follow the instructions that appear.

  3. when the Windows Installer page, click repair your computer to access system recovery options.

  4. follow the instructions.

  Please visit these links for more information on the Startup Repair:

  1. http://windows.microsoft.com/en-us/windows7/Startup-Repair-frequently-asked-questions

  2. http://windows.microsoft.com/en-US/windows7/What-are-the-system-recovery-options-in-Windows-7

  Kind regards
  Amal-Microsoft Support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Variables will not come through mailer

  I have a php mailer on my site mortgagemaestro.net and variables will not come through when I send the form to any computer but mine. I just get a blank form in my email.
  Here are the two codes
  
  Thanks for any help
  
  Stop();
  
  var b1Load:LoadVars = new LoadVars();
  var receiveLoad: LoadVars = new LoadVars();
  
  This.B1.onRelease = function() {}
  If (theEmail.text == null | theEmail.text == "" | ") theName.text == null | theName.text == "" | " homePhone.text == null | HomePhone.text =="") {}
  gotoAndStop ("error");
  } else {}
  b1Load.theName = theName.text;
  b1Load.homePhone = homePhone.text;
  b1Load.workPhone = workPhone.text;
  b1Load.theEmail = theEmail.text;
  b1Load.theAddress = theAddress.text;
  b1Load.theCity = theCity.text;
  b1Load.TheState = theState.text;
  b1Load.theZip = theZip.text;
  b1Load.theCall = theCall.text;
  b1Load.sendAndLoad (" http://www.mortgagemaestro.net/lib/phpmailer/email.php", receiveload);
  getURL (" http://l-h1.com/richard_white_lending/destpage/thankyou.php", "_self");
  }
  
  <? PHP
  require ("Class.PHPMailer.php");
  
  $mail = new PHPMailer();
  
  $mail-> IsSMTP(); send via SMTP
  $mail-> host = "mail.mortgagemaestro.net"; SMTP servers
  $mail-> SMTPAuth = true; enable SMTP authentication
  $mail-> Username = "[email protected]"; SMTP Username
  $mail-> password = "32bf1a3"; SMTP password
  
  $mail-> from = '[email protected] ';
  $mail-> FromName = "drive";
  $mail-> AddAddress ("[email protected]");
  
  $mail-> object = "Mortgage Maestro lead";
  $mail-> body = "name:"; "
  $mail-> body. = $_POST [theName];
  $mail-> body. = "\nEmail: «;»»
  $mail-> body. = $_POST [theEmail];
  $mail-> body. = ' \nHomePhone: '; "
  $mail-> body. = $_POST [homePhone];
  $mail-> body. = ' \nWorkPhone: '; "
  $mail-> body. = $_POST [as workPhone];
  $mail-> body. = "\nAddress: «;»»
  $mail-> body. = $_POST [theAddress];
  $mail-> body. = ' \nCity: '; "
  $mail-> body. = $_POST [theCity];
  $mail-> body. = "\nState: «;»»
  $mail-> body. = $_POST [the State];
  $mail-> body. = ' \nZip: '; "
  $mail-> body. = $_POST [theZip];
  $mail-> body. = ' \nCall: '; "
  $mail-> body. = $_POST [theCall];
  
  If (! $mail-> Send())
  {
  echo "Message was sent not < p > ';
  echo "Mailer error:". "." $mail-> ErrorInfo;
  "exit";
  }
  
  echo "Message was sent;"
  
  ? >

  OK, here it is incase anyone ever have this problem. I changed all the instance names as theCall and theName to variables. For this change in the area titled var: sort of in the lower right corner of the properties. I also changed the shape of the POST method and made my form a clip called sendWork

  Well here are the scripts.
  I'm still having a problem with my if statements. They stopped working after I changed everything to variables. He would still put me to the error screen that I put in place even when I had all of the information entered.

  I know it's because they are implemented by using the instance names (see above the script), but when I say that everything will work smooth, if all goes well

  Stop();

  This.B1.onRelease = function() {}
  sendWork.loadVariables ("email.php", "POST");
  getURL (" http://l-h1.com/richard_white_lending/destpage/thankyou.php", "_self");
  };

  <>
  require ("Class.PHPMailer.php");

  $mail = new PHPMailer();

  $mail-> IsSMTP(); send via SMTP
  $mail-> host = "mail.mortgagemaestro.net"; SMTP servers
  $mail-> SMTPAuth = true; enable SMTP authentication
  $mail-> Username = "[email protected]"; SMTP Username
  $mail-> password = "32bf1a3"; SMTP password

  $mail-> from = '[email protected] ';
  $mail-> FromName = "drive";
  $mail-> AddAddress ("[email protected]");

  $mail-> subject = "Mortgage Maestro lead";
  $mail-> body = "name:"; "
  $mail-> body. = $_POST [theName];
  $mail-> body. = "\nEmail: «;»»
  $mail-> body. = $_POST [theEmail];
  $mail-> body. = ' \nHomePhone: '; "
  $mail-> body. = $_POST [homePhone];
  $mail-> body. = $_POST [homePhone02];
  $mail-> body. = $_POST [homePhone03];
  $mail-> body. = ' \nWorkPhone: '; "
  $mail-> body. = $_POST [as workPhone];
  $mail-> body. = $_POST [workPhone02];
  $mail-> body. = $_POST [workPhone03];
  $mail-> body. = "\nAddress: «;»»
  $mail-> body. = $_POST [theAddress];
  $mail-> body. = ' \nCity: '; "
  $mail-> body. = $_POST [theCity];
  $mail-> body. = "\nState: «;»»
  $mail-> body. = $_POST [the State];
  $mail-> body. = ' \nZip: '; "
  $mail-> body. = $_POST [theZip];
  $mail-> body. = ' \nCall: '; "
  $mail-> body. = $_POST [theCall];

  if(!$mail->Send())
  {
  echo "Message has not been sent.

  ";
  echo "Mailer error:". "." $mail-> ErrorInfo;
  "exit";
  }

• My IPad will not come

  MY IPAD WILL NOT COME BECAUSE I MADE THE UPDATE YESTERDAY?

  If you are sure that the appliance is loaded, then press and hold the home and sleep/wake buttons until you see the Apple logo and then release. It could take up to 30 seconds of operation.