Satellite P500 - no HDMI

Similar Questions

• Problem with my Satellite P500-12F HDMI

  When I plug the HDMI cable into the port on the computer, the system generates the message "Connected TV haven't is either not turned on, is in sleep state or does not support REGZA-LINK (HDMI Control)" my computer screen then empties and my desktop appears on television, whereas it should be on both screens. Also, the HDMI option disappeared from my PowerDVD program as well.

  I received a message from Tempro Download Manager control HDMI a few days ago that I did, but when I checked the updates, it tells me the last of them was 13/11/09 without reference to it the latter.

  I checked the cables and ports on the TV, I can't think what I can do.

  > When I plug the HDMI cable into the port on the computer, the system generates the message "connected TV haven't is either not turned on, is in sleep state or does not support REGZA-LINK (HDMI Control).
  But your TV is already turned on, right? Is also enabled on TV HDMI port?
  > My computer screen, and then empties and my desktop appears on television.
  This happens only? Can you use the FN + F5 key combination and select other options?
  > while it should be on the two screens
  Have you noticed such behavior in the past?

• Satellite P500 turns off most since re install Windows7

  Hi all

  Toshiba satellite laptop
  series: P
  Model: P500
  Model number: PSPGSE
  Operating system: Windows 7 Home Premium edition

  Following a final crash of the original hard disk, so I changed the drive and performed a complete re-installation of windows7 (an original touch and put my original).
  Subsequently I have re installed the driver via the toshiba site (most importantly, so no software supplied automatically with PC purchase), and that all are present according to device (of interrogation or other point of warning) Manager.
  More through the touslesdriver.com site, I added their scanning software small told the pilot to missing day or not (so basic but all seems normal...)

  Windows of decanting finished and I started to update the drivers, windows out never normally, menu, start, stop, closing the session and after that bogus on "stoppage of work" until the "Blue Shield (about 10 minutes later, a solution or the button works / stop)."
  Single point, drivers arrive to their windows or windows installation to restart, but the problem always comes back.

  Then in normal mode, no messages or any other information that makes me say that there is a problem, but when close windows here is barattes in a vacuum no solution other than the button walk / stop (I also tried ms config: stop all, same effect).

  Now in safe mode gives the change!

  Beginning and end of windows that is no problem!

  Still in safe mode, the device section driver, then display devices, 'plug and play' shocks only information is that an exclamation mark on 'Security processor loader driver' is not visible outside the safe mode.

  No possibility of anything and much too much different information on the net which could help me solve this exclamation point and certainly my problem?

  Hello

  I own P500 too, but I use it with the new HARD drive but with the original recovery image (Win7 64 bit) I've had with her. Why have problems such as you, when I can have perfectly installed OS. That do after the installation of recovery image's own upward and the optimization of the OS. I have delete all things I don't no need and turn off all unnecessary processes that can slow down my system.
  I m really wondering why you do the same and use OS without a few installation issues.

  In any case, after reading your ad I didn t understand what your problem is, but what I can say is follow:
  Satellite P500 is fully supported for Win7 so you do not have some third-party software of the part for the detection of drivers and similar useless diagnosis. All the necessary drivers, tools and utilities, you can find and download from http://www.toshiba.eu/innovation/download_drivers_bios.jsp

  On this virtual path, I can't tell what your problem and how to fix it. I know, it's that the whole available drivers on the Toshiba download page are tested and are part of the original image recovery.
  I think either you should reinstall the OS using original recovery image and remove all the stuff, you need or reinstall Win7 clean and begins to install the drivers, tols and utilities Toshiba download page only.

  Order of installation:
  Windows 7
  Chipset SW installation utility
  Intel Management Engine Interface
  Display driver
  Intel Rapid Storage Technology driver
  TOSHIBA supervisor password utility
  TOSHIBA HW utility
  TOSHIBA Value Added Package
  O2 card reader controller
  Audio driver
  Wireless LAN driver
  Synaptics Touch Pad Driver
  TOSHIBA HDD Protection
  Bluetooth Stack for Windows by Toshiba
  LAN driver
  Sleep USB TOSHIBA and service charges
  TOSHIBA face recognition
  TOSHIBA eco Utility
  TOSHIBA HDD/SSD Alert 3
  HDMI Control Manager
  ConfigFree
  TOSHIBA Assist
  TOSHIBA Web Camera Application

  Bye and good luck

• Satellite P500 - 01 G-install the Toshiba software after clean install

  Hi all

  I have a Toshiba P500 - 01 G (http://www.mytoshiba.com.au/products/computers/satellite/p500/pspgsa-01g003/overview) running the grouped Windows 7 Home Premium 64-bit. I bought an upgrade to Windows 7 Ultimate, but can not use it, he just tells me to use Windows Anytime Upgrade.

  However, I can use it for a clean install and I intend, but I don't know what to do on the Toshiba Software (http://www.mytoshiba.com.au/support/computers/satellite/p500/pspgsa-01g003/download?os=25).
  I read on another thread that the software must be installed in a certain order and frankly I have no idea! I don't want to break something! I'm not to ask for the list accurate for each of them (except if you have time) but just a general guide as to what I should install in the order.

  Also, I guess that my recovery partition is erased in the process and I can't get it back. Is this true?

  Thank you very much. I really appreciate it,
  Abraham.

  Hello, Abraham

  I m the Satellite P500 owner too and it's really great machine, isn t it? I like it. My Toshiba best ever.
  My machine is preinstalled original Toshiba recovery image and it works without any problems so I put t want to change anything.

  Back to your question. I assume that you have a few reasons why you want to use the Ultimate version then you should try to clean OS install. Before you anything create recovery DVDs. Make two copies.
  After that make what you can do with your laptop all you used to because if you want to have the factory settings, again you can use created the recovery disc and install original recovery image.
  After recovery of registered OS image will help and you will not be able to start the installation of HARD drive recovery then please create restore DVD.

  Installing Win7? I have the European model, and I will send exact installation order list. There may be small differences compared to the model of the AU, but the principle remains the same.
  Here we go:
  Windows 7
  Chipset SW installation utility
  Intel Management Engine Interface
  Display driver
  Intel Turbo Boost Technology driver
  Intel Rapid Storage Technology driver
  TOSHIBA supervisor password utility
  TOSHIBA HW utility
  TOSHIBA Value Added Package
  O2 card reader controller
  NVIDIA driver HD Audio
  Conexant Audio driver
  Wireless LAN driver
  Synaptics Touch Pad Driver
  TOSHIBA HDD Protection
  Bluetooth Stack for Windows by Toshiba
  LAN driver
  Winbond CIR driver
  YUAN pilot DVB-T/ATSC Tuner
  Sleep USB TOSHIBA and service charges
  TOSHIBA face recognition
  TOSHIBA eco Utility
  TOSHIBA HDD/SSD Alert
  TOSHIBA Service Station
  HDMI Control Manager
  TOSHIBA Remote Control Manager
  TOSHIBA fingerprint utility
  PatchFiles FixFPService_REG_1.0
  ConfigFree
  TOSHIBA Assist
  TOSHIBA Web Camera Application
  TOSHIBA Extended Tiles for Windows Mobility Center
  TOSHIBA Network Device ID registry tool
  PatchFiles PCIIDEREG - 1.1

  I hope this will help you.

  Good luck and if you have any other questions please let us know.

• Satellite P500 PSPG8E - buddies Bios 3 times - a long two short

  Hello

  I have a question: when I turn on my Satellite P500 PSPG8E I get 3 friends: a long two short!

  What is, perhaps memory?

  Thank you d ' attribute
  Greetings from the Germany

  Michael Burkhardt

  Hello

  This laptop supports Phoenix BIOS.
  You use a google for Phoenix beep codes for details on the meaning of the code.

  But in General; the code means that an error has been detected on the motherboard. The POST (power on self-test) cannot be passed.
  Theoretically, it may be a RAM issue, but it's just a suggestion.

• Installation of Windows 7 64 bit on a Satellite P500

  I bought the above system in August last year with 32-bit Windows 7 installed. I understand that it is not possible to upgrade and to a complete new installation. Is it necessary to format the hard drive first? Have backed up all my data (there was not a lot), but wonder if there is something else I need to know before you continue. Any help would be much appreciated.

  Hello

  I m a bit confused because I have too many Satellite P500 and, as far as I know, this laptop model comes with 64-bit only.
  Can you please tell us what P500 you exactly (P500-xxx)?

  You are right; before installation Win7 HDD needs to be formatted. If you have installed the OS in the past, I guess you know how it works.
  Associated with Toshiba here are two things you should know before starting with the installation of Win7 64 bit:
  # Create recovery with the original Toshiba image DVDs. This disk, you can use if you want to have the factory settings once again.
  # Drivers, tools and utilities must be installed in the proper installation order. If you ned some hep with it let us know.

• Satellite P500-190 stuck in a loop

  Well, I try to summarize what has happened so far.

  I have a Toshiba Satellite P500-190 has started acting as each task is too big for him, constantly showing disk hard loading, programs did not respond for a while... then I ran the reconverty tool, reset the c drive, the problem still there.

  I ran all the error detection of characteristics of pc, no hardware problems or software detected. So I installed malwarebytes anti-malware and ran a scan, it finds errors, but before I could act, the program froze again no response. Press ctrl alt del, black screen, no response... reboot. Now my dosent pc even trying to start windows, only error detection program and each restart goes like this, even after going through the program as it is said.
  I tried to get to the other menus of repair, but it says I must be logged in to do this.

  Any ideas how to continue?

  Hi bug

  Please reinstall the recovery image and boot OS without having to install additional stuff.
  Do not connect to the internet and check the functionality. Open some pre-installed apps and see if they will not work correctly.

  Play around with these factory settings and let us know if there is a problem.

  How old is your Satellite P500?

• Satellite P500 - blue screen on webcam whenever I try to use Skype

  Whenever I try to use Skype all I get is a blue screen where my webcam should be. I checked to see if my webcam doesn't work at all, and all I get is the web cam iniliziation failed Please check device and restart.

  I tried this but nothing helped. I also tried to reinstall the camera and update the drivers. Still nothing.
  Any help on this would be greatly appreciated. I was told that if I update the BIOS it might be useful, but I also said that this could screw up the laptop completely...

  Brenton

  In front of me, I have Satellite P500 and I use it almost a year now. Since the first day I use it with Win7 preinstalled original and Skype.
  Up to now, I have strength to have one problem with cam or Skype. Everything works fine.

  Are you using the original pre-installed OS? Since when you noticed this problem?
  You can use cam with other applications?
  Cam is listed in Device Manager?

• Satellite P500 - noise varies and is too quiet

  Hello again,

  I had some problems with speakers this time.
  Since there are Harmon/Kardon speakers installed in the computer, the sound itself is fine.
  However, it is not.

  Sound is too quiet, even if I listen to music on the max volume.
  As well, I noticed the sound fluctuates all the time and there are crackling noises.
  All audio drivers are up to date, but they did not help.

  Could you please tell, what's the problem? Thank you!

  Perhaps what is its volume in the drive that you use low upgraded? Select this check box.

  Friend of mine has bought Satellite P500 last month. We have installed OS, created recovery discs and tested sound using Skype, Winamp, Windows Media Player and watch blu - ray discs.
  With the sound, everything seems to be OK.

• Re: Satellite P500 - 1 CG-conexant cx20583 driver for xp x 64 wanted

  Hello...

  I installed on my laptop (Satellite P500 - 1 CG) windows XP x 64 and already found almost all the drivers, but still, I can't find the right drivers for the sound, already downloaded on the web that some pilots who were supposed to be for XP x 64, but none of them do not work.

  Can anyone help?
  Sound card is conexant cx 20583

  Hello

  Unfortunately, there are no drivers for Windows XP 64-bit on the Toshiba driver page.
  As a solution, you should go to the provider's site to download or use programs like the genius of pilots to collect.
  Note that some drivers did not at all exist.

• Satellite P500-153 - computer freezes during absence after - min

  Hello

  3 months now, I bought a new Satellite P500-153. My problem is that the computer very often been completely freeze after 30 to 60 minutes when I'm not working on it. The only possibility is to press the power button and restart. Last Sunday, it freezes also for the first time, when I'm working on the computer.
  All recommended updates are performed.

  Anyone has the same problem?
  Do - does anyone know why or what I can do?

  I hope someone can help me.

  Thanks in advance!

  Frank

  Hey mate,

  What additional software you have installed?
  Have you updated to the drivers and what OS you have installed?

  In this case, it's really hard to say what is the cause, so you should test with factory settings and see what happens.

• Satellite P500 - 1 CG - PCI Simple Communications controller driver for Win 7

  I reinstalled the system in my Satellite P500 - 1 cg, because it was in English and I use the Polish language.
  After the reinstallation, I have a problem and I need a "PCI Simple Communications controller / pilot.»

  Can someone help me on this?
  Thanks in advance for any help...

  Hello

  To be honest PCI Simple Communications Controller does not for me
  I think that there is a translation error.

  Please check this doc from Toshiba:

  How to identify an unknown device
  http://APS2.toshiba-tro.de/KB0/HTD0302U00000R01.htm

  It helps you to identify the device and find the right driver.

  Welcome them

• Bluetooth on Satellite P500-16F

  Hello, I am using laptop Toshiba Satellite P500-16F and...
  I want to use the program "BlueSoleil" of bluetooth, but it says "hardware not detected".
  Now, I see the following options (with the following options under such as shown below)

  USB
  --- X

  UART
  -COM PORT {1-255}
  -In bauds {75-13824000}
  -Size in bytes {4-8}
  -The parity {even/odd/none}
  -Stop bit {1/1.5/2}
  -The Frother {None/RTS-STD/DSR-DTR/Xon-Xoff}

  PCMCIA
  -COM PORT {1-255}
  -In bauds {75-13824000}
  -Size in bytes {4-8}
  -The parity {even/odd/none}
  -Stop bit {1/1.5/2}
  -The Frother {None/RTS-STD/DSR-DTR/Xon-Xoff}

  PSCO
  -COM PORT {1-255}
  -In bauds {75-13824000}
  -Size in bytes {4-8}
  -The parity {even/odd/none}
  -Stop bit {1/1.5/2}
  -The Frother {None/RTS-STD/DSR-DTR/Xon-Xoff}

  Please tell me what option and sub-options should I use to make it work

  Hello

  The whole story is quite simple. Your laptop is shipped with the BT module and preinstalled Toshiba Bluetooth stack and Toshiba is responsible for the functionality of BT module with pre-installed software. It is tested and should work correctly.

  On that moment when you've taken the decision to use a third party software developed by another company, they should help you with support.
  You'll be really lucky if anyone here have the same model of laptop and use the same software but before you wait here I recommend you to check the BlueSoleil under http://www.bluesoleil.com/support/Default.aspx customer support

  They have the best experience with own products and I think also that they tested the feature on different hardware platforms.

• Satellite P500 boot nor OS install

  Hello & lead greetings to all friends of the Forum.

  Please, could someone kindly look into this problem for me.

  My laptop, a Toshiba Satellite P500 is defective. It will boot after post and as soon as it reaches the "Starting Windows" (WIN 7) logo splash, it freezes and it will stay like that for hours. I changed the hard drive, the memory modules, I tried to reinstall the operating system, I tried to boot with a Linux Live CD, Live USB and DVD USB, but all help drive does not. I changed the BIOS configuration, and then reset to default, again without success.

  Don't you think it's a fault of MB, CPU or GPU?

  And someone has a suggested method of remedy?
  I thank you all in advance and will be happy to help anyone!

  Thanks again!

  Hello

  You have already replaced the common areas like the HARD drive and memory.
  It was my first idea of memory or the HARD drive may be affected, but if you are sure that the new parts are ok, then the problem might be related to the motherboard.

  Usually if the CPU would be affected, then the POSITION could not be transmitted correctly.
  So it seems that this motherboard you could go wrong function which means that the fix will be really expensive since the new motherboard is one of the expensive laptop parts

• Re: Editing on Satellite P500-12F .mts files

  Hi, I have a question about the change. MTS files:

  My laptop is a Toshiba Satellite P500-12F / Core 2 Duo P8700 2.53GHz / RAM: 4 GB HD: 500 GB / BD - RE DL / 18.4 "/ Windows 7 Home Premium 64 Bit /"

  And I use Corel video studio pro X 3 to edit my SD videos and I was very happy with it until I tried to use the software to edit HD videos very short 2-4 minutes long that I got from a friend to test it before buying my HD camcorder.

  These videos are played on the laptop without problem using WMP or video studio pro x 3 in the preview window, the problem starts when I add another track of overlay to make modifications or any title or effects on the overlay track as I used to do with SD videos.

  If I do any sort of editing and try to see the changes in the preview window, the image moves very slowly, vibrates and the sound is broken, it seems that I'm editing a 24 hours of work not 2-4 minutes. clips.

  So I do not understand where is the lie of the problem, what is the spec of the laptop? What codecs do I need to install? Or the settings that I need to do?

  bye the way, if I decide to save the changes I made for the video it is so annoying to check during the preview/editing process, the final file plays great without problems and in HD quality.

  I wonder if someone can help me.

  Thank you

  Aiman

  Hello, Armelle

  Please don't get me wrong, but I do not understand the relationship between issue described and Toshiba laptop.
  Don't you think that it is the related issue of Toshiba or you should speak with the support of software manufacturer?

  This application can be installed on your laptop as part of the recovery image, but I don't think that Toshiba is responsible if you have a problem with a software feature.