Satellite Pro 6100: BSOD after use of the 6000 SP recovery CD

Similar Questions

• Satellite Pro 6100 stops after 15-30 minutes

  My satellite Pro 6100 Cup after 15 to 30 minutes of operation on power outlet. There is a noise and all the lights go out except orange slow flashing (power problem). I have restore by removing the power cable and wait a while.

  It will then start again. I used two different adapters and two different batteries. It also happens if work on AC with no battery in the. My suspicion is an overheat cut-out. The Sat Pro has a? Could it be clogged with dust inside (it is 5 years old)? If yes how I clean. I don't think it's a fan failure because I can hear the fan cut in. Advice much appreciated. Thank you.

  > Could it be clogged with dust inside (it is 5 years old)? If yes how I clean. I don't think it's a fan failure because I can hear the fan cut in
  I agree with you and the user SambadeAmigo. It seems like a simple problem of overheating and so the laptop automatically stops to prevent the equipment from damage

  I assume that your laptop can be enabled again after being allowed to cool. It is a common question if the cooling modules may not work properly because of the dust and debris.
  As suggested, it would be possible to remove dust using the can of compressed air.
  It should work.

  See you soon

• Re: Satellite Pro 6100: can I use RAM PC3200 modules

  Hello

  I looked on the specification for this laptop and it does not have to go on 1gig, on the site of crucial, it says to use pc2700,

  But the laptop would always fully work with PC3200 (400 MHz) in it?

  Also the laptop actually supported on 1gig?

  Thank you

  As much as I know the Satellite Pro 6100 supports a FSB 400 MHz.
  So, theoretically, you can use the modules supporting 400 Mhz too.

  It is important that you use the modules DDR SODIMM 200 pin.
  The Mhz may be different.

• Satellite Pro 6100: Bluetooth - how to connect the mobile phone

  I already have a satellite pro 6100 with the bluetooth software on. I tried to connect to my mobile phone without success. The problem seems to be with the laptop rather than the phone.
  How can I connect successfully. I have to update the new drivers? I bought it refurbished 3 years ago and I'm just getting round to the use of bluetooth!

  Well, the Bluetooth software has been installed on your laptop, BUT the question is:
  Your group has installed Bluetooth card?

  AFAIK the Bluetooth is an option available on this unit. You must check the Device Manager and check the bottom of the unit if the Bluetooth label has been placed.

  I think that you cannot connect your mobile phone because BT is not available.

• Satellite Pro L300: BSOD after updating BIOS

  Hello

  After updating the Bios of the Satellite Pro L300, windows will not start!
  His show the blue screen of death!

  What can I do?

  Hello

  You are able to access the BIOS settings?
  I m not very well why this BSOD appears, but eventually the SATA mode settings have been changed after the BIOS update

  Usually the SATA mode must be on AHCI if the SATA drivers are installed.
  But if the SATA drivers are not included the SATA mode must be set to compatible.

  Please check this!

  In addition, you could set the BIOS default settings and may try to start the computer again.

• Satellite Pro 6100 how to use recovery DVD-ROM with vmware products

  Hello

  I like to use the recovery DVDs of product (T201651-GR) of my Satelite Pro 6100 on VmWare player, because I use openSUSE Linux as main operating system (not Windows installed on the hard disk).
  I do like install and save hard disk laptop, so that to restore later inside the vmware. If it works?
  I wonder if someone can tell me how to use my legal version of Windows XP on VmWare player?

  Thank you in advance,
  Bernd

  Hello

  I doubt that it works with VmWare.
  Why?
  Because the restore CD contains the ghost image files and you will need to boot from the recovery CD for installation.

  So I see the chances of getting this job running VmWare.

• Satellite Pro 6100 - unable to connect to the WLAN router

  Hello

  I brought a 2nd hand Satellite Pro, model version SP6100 (PS610E-029ZV-EN), P4 1.7 Ghz, 512 MB, 30 GB, with Windows 2000 Pro loaded.

  I can't connect to my wireless router. The switch is in the correct position.

  I want to change to XP using the key provided with the new laptop (dual OS) however I can't reformat using a XP disc at the start up or if I use the recovery cd (start with holding C and let go when he works up) it starts but displays 'specification drive not valid' three times and charges Win2000.

  Can someone advise how (or if!) Can I reformat I want?

  Any help will be greatly appreciated.
  See you soon.

  Are you sure that the wireless network adapter has been installed in the laptop?
  Check in Device Manager

  On some series WLan is optional. This means that the WLan card is not installed, but it is possible to install an and, consequently, the laptop contains the WLan switch.

• Satellite Pro 6100: no LED at all, the machine doesn't work anymore

  Hi all
  I have two nb, a 6000 and a 6100. Never had any probs with the 6000, but my 6100 gives me a real hard time:
  The battery has been fully charged, when out of nowhere, it froze... had no chance, but power button money to stop, something cut, two green LEDs (which is normal, right?)
  Down the silver power button to restart, nothing.
  Plugged the AC supply (because the battery is fully charged, see above...): all of THE lights is empty, no lights at all.
  Pressing the new button, NO RESPONSE AT ALL, it totally DEAD!

  What could have caused this? What can I do? any help appreciated, thanks.

  very desperate, lionmouth

  Hello

  It seems that there is a hardware error that couldn t be repaired by a biosupdate or something. You will need to bring your machine to a partner of service approved for repair/hardwarecheckup. One of my friends had a similar problem with its 6100 with exactly the same symptoms and his "mother" was defective. But at this time the machine was still in warranty so I Don t know how´s with your mobile phone.

  See you soon

• Satellite M300 switched on after using surf the net

  Hello

  I find out that this forum, I hope, can help answer my question.

  My Satellite M300 laptop with ATi graphics card
  Normally I use net surfing with Lan or Wifi turn off properly.
  But after a few seconds the machine automatic lights.

  The service center people have no idea of this problem after motherboard change, wifi, lan Board, camera cable, adapter, ram but still the same problem occur.

  Can someone help me answer? :(Merci.)

  To be honest, your ad is rather confusing, and I don't understand any of your problem.
  Maybe just your English is so bad. ;)

  If I understand you just your laptop wakes up alone. Right?

  In any case try to disable wake up on LAN in the BIOS settings.

• Unlike satellite Pro 6100 (PS610E) - two versions of the Bios?

  Hello

  There are two files of bios for this old laptop...

  1.90 - TRAD
  1.90 - WIN

  What is the difference?

  Best regards & thanks in advance

  Tom

  TRAD (traditional) version can be made using the floppy drive and the BIOS update should be saved on the diskette.
  WIN version can be started under Windows operating system.

  All that s.

• Re: What can I do to get my Satellite Pro 6100 from the dead?

  It's now quite a few years I have a * Satellite Pro 6100 *. I recently had the following problem.

  * _Problem_ *.
  When I press the power button to turn the computer into the AC power light starts flashing orange light (flashes come in groups of eight, the second and eighth flash are longer). Nothing else happens: the computer is dead as a brick. To stop the flashing, I have to disconnect the main power supply and remove the battery.
  * + Note: the power supply is ok.

  * _Question_ *.
  What should I do to restore normal operation?

  Thank you

  Post edited by: hnav

  Hello

  I put t think you will be able to do anything that would bring back the laptop from the dead.

  According to your description books sends a flashing error code that appears always if a motherboard error has been detected.

  In your case only an ASP might help you.

  First, the technician would be able to read the code and then to know what part is malfunctioning.

  In the worst cases, the motherboard must be replaced; (and this could be a costly affair.

  Good luck

• Satellite Pro 6100 - after updating the BIOS, it does not

  Hello

  I am trying to upgrade my old of Satellite Pro 6100.

  I started to upgrade the Bios via download from Toshiba (using WIN) site - OK downloaded zip files and installed, machine then stops. Problem, it does not restart - it's so now I have a laptop 'death' that is not responding to any key I tried.

  Any suggestions of resuscitation?

  Already I've updated from XP to SP2.

  Thank you

  Paul

  Hello

  It sounds like that the BIOS update has failed and your laptop can start t again. But try this workaround:
  Remove the AC adapter and the battery and then wait an hour. After that reconnect the adapter AC/DC and battery. Try to start the laptop.

  If it doesn t work I think that the motherboard needs to be replaced or you go to an authorized service provider. Technicians can reflash the ROM module
  But maybe you can find a motherboard of second hand cheap on eBay

  Good bye

• 'Bad RTC battery, check the CMOS' on Satellite Pro 6100

  Hello... I just got a Satellite Pro 6100 and when it is started I get an error message:

  RTC BATTERY BAD
  BAD CHECKSUM (CMOS)
  Check the system. Then press the [F1] key
  _

  I can still use the laptop for about 15 minutes, but then it crashes. I did some research and discovered that it is the power supply Board. But my laptop is out of warranty and the reminder is now officially over.

  Y at - there someone who can help me?
  Thank you
  Liam

  Published by: admin

  Hi Liam

  Hmmm... I think it s not a Council but the battery of the CCF.
  Take a look in the user manual. There you should find something that exactly the message is displayed if the battery RTC (BIOS) is not charged.

  The RTC battery, you must connect the power adapter and should run the laptop for about 24 hours.
  After that the main battery has been charged, then the RTC battery starts to load.

  It will take a little longer.

• Satellite Pro 6100: cannot get into the BIOS and does not start

  I have a portable Satellite pro 6100, en I was trying to boot from an external USB hard drive. When I activated the second hard drive option in the BIOS it has stopped booting all in all, I can't even get into the BIOS Setup more. All I get is "In touch with tomorrow TOSHIBA" screen with the icons to select the method of priming preferred manually after it's just blank screen with a cursor blinking in the upper left.

  Press ESC or F8 before to turn usually results in fast beeps sounds.
  Press tilde (~) before turn is reflected in the remaining space screen (not even the home toshiba screen appears) and slow Zens sounds.

  Apart from that I can't really do nothing at all.
  I tried to reset the BIOS by disconnecting the battery CMOS/RTC (hoewever, we call it) of the motherboard for a while with no results.

  Turn on/off without the results of HD internal in a white screen with an ERROR 'IDE #0.
  I can always stop by pressing the power button, you don't have to bother on the external hard drive it past I don't even want it works more.

  Suggestions?

  Hello

  I agree with Graeme. Your HARD drive is probably faulty. Sorry, but I don't think that you will be able to use the external HARD drive. The option in the BIOS is not for EXTERNAL HARD drive is just, I guess, for disk HARD placed in select Bay.

• Satellite Pro 6100 - how to change the date and time in the BIOS

  Hello

  I received a satellite pro 6100 that had not been used for some time. Windows does not work then he reinstalled with the good drive.

  When I try and windows 'enable', I get the error 32777 and the laptop is unable to connect with the activation servers that a google leads to believe me that the date and time are incorrect in the bios.

  I know that Press esc to access the bios but there is no option to change the date and time in there. I put the date / the correct time in windows, but this does not seem to synchronize with the bios. I've updated to the latest version of the bios, but this is not enough.

  How can I change or update the time in the bios?

  Thank you

  Hello

  I doubt this time and date setting BIOS does affect Windows activation time Windows doesn t affect it in my opinion. There must be another reason for this problem.
  You can activate Windows by phone?

  Normally the date and time in the BIOS can change you if you mark the date or time, and then press on + or - to change this. Sometimes you have to press PageDown/to the top according to the model of BIOS or laptop.
  Usually in the configuration of the BIOS you will find a brief info how changing the values.

  Check this box!