Satellite T110-107 - Touchpad does not properly

Similar Questions

• Satellite T110-107 - Reboot does not work properly

  When the power button is pushed to the power and wireless lights, fan whirs a minute then nothing more happens. If I remove the battery and leave it for 30 minutes then it starts fine when you push the power button. Currently abroad, but have access to the internet.

  Running Windows 7.

  Suggestions welcome!

  Hey Buddy,

  Since when did you notice this problem and have changed something on the hardware configuration?

  It is difficult to say why it happens but it must be a hardware problem, you still have it installed the newer version of the BIOS for Satellite T110? You can download it from the official website of Toshiba:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  But before you start the update, close all running programs (also AntiVirus and firewall).

• Satellite T110-107: touchpad problem - pointer move sometimes

  Good afternoon everyone,

  Currently I have a series of Satellite T110-107 and have problems with the touchpad.

  I start the computer and the touchpad works very well for a few seconds, after that, the touch pad stops working to full capacity.
  If I wander my fingers on the touchpad and the pointer does not move, sometimes it will move up and down, but not as it should.

  It is a common problem, or is it a hardware problem... or is it the fact that I'm just not accustomed to having the correct settings on windows7?

  All help reveal be great, because it's very frustrating!

  Kind regards!

  Hello

  I found a few tips and tricks that you should try.

  First, you must change the sensitive touchpad settings to lower the level.
  Go to control panel-> mouse and all the settings for the touchpad to the value has a less sensitive level.

  You should also right click Synaptics Pointing Device (in the taskbar) and get in the middle of the page Double click speed on.
  Move the slider to half way down the beach. This should help you too.

  Last but not leas, you will need to disable zoom pinch.
  Go to the icon in the lower right corner Synaptics pointing device, click on 'The pointing device properties', click on the "Device settings" tab, then the settings button. Uncheck "Enable Pinch Zoom" under "Pinch Zoom".

  Greetings

• Satellite L50-A013 - touchpad does not work

  Hi all

  I've had my L50-A013 Satellite for about 7 months now.

  In the last month or so I started to have problems with the touchpad, freezing and does not not my contact.
  This lasted a few minutes at a time, then came the back of its own accord, almost like a very long latency period.
  This morning, however, I turned on my laptop and the touchpad does not work.

  Device Manager does not display a mouse or pointing device at all until I attach a mouse USB.
  By pressing the key that normally activates / deactivates the touchpad does not work - nothing changes and the light does not turn on in both positions.

  I tried reinstalling the drivers without result, and windows is no update that might help (or any recently that might have caused the problem).

  If anyone has any other ideas for what I can try, it would be amazing.
  The laptop is under warranty so I can hopefully get it fixed, but if possible I would really do not have to go without a computer until it's settled.

  Thank you all for your time,
  -Sase

  Hi Sase

  It is not easy to say what the problem is, but I can imagine that there is hardware problem. Perhaps touchpad loses the connection to the motherboard. I mean if this piece of hardware is not detected I can imagine this scenario.

  Of course best test you can do now is to reinstall OS and test functionality with the factory settings, but will delete your actual configuration of OS and software pre-installed.

  If this kind of test is possible do. If not, I think you must contact the nearest Toshiba service provider and ask for help. They have special diagnostic tools and they can check it for you.

• Satellite A350D - 20K - Touchpad does not

  Hello Madam / Sir:

  Please give me a way on how can I fix my laptop problem. I use Toshiba Satellite A350D - 20 k, its original operating system was Vista 32 bit. As I discovered that my machine has been supported to use Windos 7, I decided to change my OS to Windows 7 64 bit. When the first time I've used it using Windows 7 OS my touchpad worked again.

  But change a BONE I have to find the driver, so I was looking for your www.computers.toshiba-europe.com site, so I found the latest updates for family series specifically A350D but not A350D - 20K I can't find this exact model updates up-to-date, so the updates of the A350D I saw, I downloaded all of them even the update of the BIOS...

  Before that I use version 1.2 of the BIOS, but since I saw a latest version which is version 1.7, I decided to install it. After that I installed it I noticed that time if my touchpad does not work because I use a mouse (external device), maybe that I installed it Wednesday, October 6. For some time, when I take my mouse when I tried to use the touchpad, that was the time I noticed that it does not work.
  I don't know if my bios version change has been the one who made this problem.

  I asked some recommended to my friends and they asked me to the Toshiba site, if there is a BIOS utility crush so that you can restore your previous BIOS or if they still have the old version of your BIOS which is 1.2.

  So now please dear I sincerely ask a help for my problem. Thanks a lot for your time in reading my concern.

  Edit:
  In addition, I already recover my lap top using may but recovery disk, it does not solve my problem, my touchpad still didn't work. My drivers in Device Manager is over. The driver installed in my device manager is

  * mouse and other pointing devices *.
  Compatible mouse HID
  Synaptics PS/2 Port TouchPad

  Hello

  Satellite A350D - 20K belongs to the series PSALME. According to the Web of Toshiba BIOS update site that you can find for A350D (version 1.70 - WIN) is compatible with all models A350D so I guess that the BIOS update isn't the cause of the problem. As a general rule after a BIOS updated you must load the defaults in the BIOS if you press the F9 key in the BIOS Setup. This will load the default settings.
  Also, make sure that the internal pointing device (touchpad) is not disabled in the BIOS. On some laptops you can disable it in the BIOS and it must be set to activate.

  After the installation of recovery also try the FN + F9 key combination. With this combination of keys you can also turn off/turn on the touchpad.

  Check this box!

• Re: Satellite P205-S7469 TouchPad does not work

  Hi guys.

  I bought this computer a year ago in the States. Then I moved to the Sweden.
  My hard drive crashed. Buy a new
  But I left apperently all CD for the computer back to the States-. -.

  So now, I have downloaded Microsoft windows Vista Home Premium because it's what I had before.
  Used the CD Key which was written under the computer.
  If everything works Gr8 except my Touch Pad...

  I installed all the Windows Update drivers were able to give me.
  Went to support toshiba and downloaded page the drivers from there.
  But still, nothing. It won't work.

  Anyone know what I can do? Or what is the problem.

  Thank you all for all the help you can provide me.
  Lol XoXo

  Hello

  I have no idea why the touchpad does not work yet, you have installed the good drivers do you have?

  Are you sure that the touchpad is not disabled? Usually, you can disable the touch pad using the FN + F9 key combination. Check it out.

  The P205 Sat is very similar to the European model Toshiba Satellite P200.

  Maybe you can download two Touchpad (Alps Electric and Synaptics) drivers from the Toshiba European page choose either of the P200 series and check the drivers!

• Satellite L40 - 18W - Touchpad does not work

  Hey guys...

  I have Toshiba Satellite L40 - 18W, bought in the Middle East, and unfortunately its touchpad does not work... I checked and double checked all the possible places, so anything that is disabled or misconfigured but found nothing.

  As there are quite a few errors in the operating system I formatted my hard drive and install WXP Prof, installed all the drivers, but the touchpad is not always works. I'm very confused as before and after formatting the pointer moves a little when I use the touch pad at the beginning of the UPA start? ¦

  Help, please...

  The best audit is to install the operating system with the original Toshiba recovery image and test it with the factory settings. In this case touchpad should work fine. Otherwise, contact the service and leave check your laptop.

  Sorry, but I don't see another solution for you.

• Satellite S50T-B950 - touchpad does not work after update of Windows 10

  Hello "Toshiba."

  After the update for Windows 10 I have a problem with the touchpad does not work and became come boiling Forum and found that the solution is to uninstall "MOMENTUM Input Device" to "Device Manager", finally worked the touchpad, but alas multi touch properties such as: "zoom/minimize gestures of scrolling and two-finger" no longer work

  Please help me solve this company of Toshiba problem

  The same theme has been already discussed and resolved in this thread:
  https://Forum.Toshiba.EU/showthread.php?83885

  Then please follow the proceedings in the other thread to avoid misunderstandings

  by the way: here is the link to pilot site Toshiba win 10:
  http://win10upgrade.Toshiba.com/swup...SPX?region=TEG

• Satellite L500D - 16L - touchpad does not work.

  I have a new L500D but my touchpad does not work.
  My diagnosis of computer told me that there is no problem, I have a mini mouse USB connected, would that be causing a conflict?
  Can someone please give me some advice.

  Thank you

  Try to press Fn + F9 to toggle the Touchpad. Also take a look in the BIOS, the touchpad can be disabled it. Also try to uninstall the software for your mouse USB mouse (if you have installed everything), this software can cause a conflict.

• Satellite L50D-B - TouchPad does not work properly

  My TouchPad is not working properly, it stops working after a few seconds after the start. Can someone help me?

  To be honest, it is not easy help these problems.
  What exactly happens? Touchpad is completely off? I want to say is there any kind of reaction?

  Have you tried to turn again using the F5 button?

• Satellite T110-107 - Touchpad / mouse problem

  Just had delivery of a new Tosh T110-107, I have to say is beautiful, however a problem. A startup the touchpad works ok, but as soon as I plug the mouse USB may not work - what makes the system unusable until I disconnects me restart and the mouse. So what have I so done for her?

  Uninstalled McAfee and Norton 360 addded and office (two originals) and that's the problem were found until everything has been done - as he came out of the box.

  Win7 Home Premium, never had any problems with Win7, but then not used on a particular laptop model. Can only imagine its software/config but straight out of the box? Tosh must know there is a problem-they have too, but sold it?

  Does anyone else have this problem?

  Answer to Ah my own question, mouse at fault, as soon as the wheel is moved all the works, but we must constantly move or it don't work. It turns out that the mouse was not part of the package, so apologies to Toshiba, but then, that's why I had to buy this machine of large model - deemed manufacturer - if and I would recommend it to anyone who is thinking about buying one.

• Satellite L305D-S5873 - touchpad does not work under Win XP

  HUGE problem
  Key Satellite L305D - S5873 DOESN'T work under XP.

  I am with XP now and doesn't work, while I had Vista it worked and he stopped.
  Then I installed the xp and still, it does not.

  Hello

  So you say that the touchpad works properly using the Vista operating system, but you are not able by using the touchpad running Win XP.
  Is this good?

  If Yes, then I think that you have not installed the XP drivers good touchpad.

  Satellite L305 belongs to the Toshiba U.S. series and you should visit the Toshiba driver page us to get XP drivers

  Sorry, but for me it s a clear case. It's a softer question, and possibly the right driver installation is required.

• Satellite Pro L300 - touchpad does not work

  Hi all that I need help urgent because it drives me crazy. First of all, I use XP PRO. My laptop is fairly new, only around the age of 4 months, I had no problem with it at all. I formatted my laptop yesterday and reinstalled all the drivers that I downloaded here:

  http://www.ISD.Toshiba.com.au

  and everything works fine except the touchpad. I have already installed shared, utilitarian toggle the touchpad Module and I have the latest BIOS installed and reset all default settings and I made sure that the touchpad is enabled in the BIOS, but also pressing FN + F9 to enable during Windows.

  I installed the latest touchpad driver Synpatics I downloaded from the homepage of Synaptics. But for some reason any, that it does not work, I don't know what is the problem here. My touchpad worked before I formatted my laptop, it worked fine and has never had any problems. Will you please tell me what is wrong because I need to use my touchpad sometimes as well, so I can't use a mouse all the time.

  Hello

  > I installed the latest Synaptics touchpad driver that I downloaded from the home page of Synaptics
  I think that you question refers simply to the driver for the touchpad that is missing or incorrect.
  I put t know how it works on Toshiba notebook Australian, but the Toshiba European Satellite Pro L300 units needs touchpad different drivers. some use the Toshiba touchpad driver and some units need a driver for the Synaptics touchpad.

  In your case, I recommend this controlled again.

  By the way; My touchpad is always disabled so that en external mouse is connected.
  It is parameters that control it. Please check in your touchpad properties too!

• Portege M800 - Touchpad does not properly on Windows 7

  Hello

  In windows 7 the touchad does not work properly, which means I can't scroll pages by dragging my finger on the edges of the touchpad. It worked perfectly witn Vista and now it isn't. I have the 64 bit version.

  I tried new drivers, but there aren't any. How should I solve this?

  Thank you

  Hey Buddy,

  You have the most recent driver for the touchpad? Usually the Vista drivers also work on Windows 7.
  Check this box!

  In addition, the exact model number would be interesting.

• Satellite T110-121 - Wireless does not work after sleep in Win7 Home Prem 64

  Hello

  I bought Toshiba Satellite T110-121, with Windows 7 Home Premium.

  Problem:

  1. after going into Sleep Mode, when he wakes up, my WIFI does not work, unless I'm in wireless network card setting, Advanced tab, then I change the Tx to say 100% to 75% power level, then the WLAN will work.

  2. I tried to adjust the setting for power management on the network card for maximum performance and does not disable during sleep and also in the Bios but nothing is

  3. I use Realtek 8191SE drivers have been updated (wireless card, Ethernet, Bios)

  Thank you

  As much I know Tx power level option must be set to Auto.
  Have you noticed the same behavior with Auto option?