Satellite T130 - restart button stops, instead of reboots

Similar Questions

• Satellite S50T-A - button / stop does not

  Hello

  I am running Windows 8.1. After that most recent Windows Update and then restarted, the computer froze to the Toshiba start screen. Fan went into overdrive and so I pushed the power button / stop.

  Now, seems dead - button / stop, black screen, no its HARD drive is unresponsive. Only signs of life are power and battery LED on the front of the computer. Press and hold the power button for more than 10 seconds do nothing.

  Any ideas?

  Hello

  Stop switch force (hole) is available at the bottom of the laptop.
  In the case of PC freezes, do not start or a power failure, which can be fixed by pressing the power button for 10 seconds (force shutdown) and now, use the stop switch to force

  I found this info in this document of FAQ from Toshiba
  [The stop switch of strength (hole) for models with one main battery fixed | http://aps2.toshiba-tro.de/kb0/TSB3C03JR0000R01.htm]

  A short feedback would be greatly appreciated.

• Satellite M40 - 277 keeps restarting - button / stop?

  I have the problem that the (per hour to enter acient) laptop Satellite M40 277 of mine keeps restarting unpredictibally. Initially I have if it was a problem of overheating, so I used SpeedFan and CPU-Burn a test, but the computer does not restart until the airflow to the bottom is fine (I consider that the entry of the fan on the bottom a design error, but it's something else). Now, if the air flow is a bit stuffy, the laptop stops at about 83 and then it will have difficulty to challenge. Ok.

  However when the laptop is about 63C it restarts sometimes and I feel, it can be a power button is stuck. I have XP installation so that it will always ask before you actually stop, and when I pick up the phone on the side (the plastic box where the power button is integrated in waiting) I often question of the judgment. NP, just click away. But I also feel that the button can get stuck and then the system turns off after 5 seconds of 'holding company' the power button.

  So I just tried to get a quick glance and we should normally be able to remove the keyboard, but this M40 is a challenge. Even after that the keyboard is free, I don't see the actual power button.

  Is there anyway to loook under high elegant green rim the power button? How to open this thing up?

  Tom

  Hello

  As far as I know this little switch cover is fixed by 6 latches and connected with small flat cable to the motherboard. It just seems but if you don't know how to remove it you can damage these small latches and later you won't be able to fix the new.

  Anyway, if you think that this power button / troubled maybe just make the switch cover replacement may solve the problem.
  What say about it? Try to get the spare part and ask if anyone can exchange it for you.
  Of course, the best thing is to ask for professional help, but it will cool somewhat.

  Another way, do a risk and try to replace one.
  Let me know what you think of this.

  Good bye

• Satellite L755D: Start button / stop static is red when I stop

  I have a Toshiba laptop, L755D.

  Recently, when I stop the laptop and turn off the power, the power led turns on a few seconds after stopping.
  He remains a static red color until I connect upward when it returns to normal color blue/white.
  While the stop of the battery loses the power of 1 to 2%.

  Can anyone help please?

  > While the stop of the battery loses the power of 1 to 2%.
  Check this box:
  Why lose 2 to 4% battery by turning off then back on my mobile device?
  http://APS2.toshiba-tro.de/KB0/FAQ9C012L0001R01.htm

  It is normal for a unit to lose between 2-4% battery, when to stop and reverse.
  Battery re-gauge it's self when starting back from an engine out of State. An accurate reading of the battery can take up to 5 minutes.

• Satellite T130 is no longer able to restart (reboot)

  I have satellite T130 - 10G PST3AE bios v2.7 and he can't restart.
  After a reboot the white of the screen the fan made noisy becames for a short time and that's it.
  To start it again, it is necessary to turn it on. It starts normally.

  Reboots tried Win7, Linux Fedora, Bios Setup (when it is saved), ctrl-alt-del before start of operating system (Start menu). The result was always as shown.

  Thank you for any suspicion.

  I think it's hardware related issue, given that this problem seems to appear by using all the different systems (windows, linux)

  But have you ever tried the new installation of the OS? If this isn't it!

  Return to the idea where a malfunction of the equipment:
  I think first the RAM modules should be tested and verified. Given that the RAM modules could cause such or similar issues, I think it's a good idea to check this part.
  The best would be the use of nine tested modules, though.

  But if the motherboard is affected, the new modules would be not useful much :(

• Satellite T130 keeps restarting instead of close

  Just bought a laptop Toshiba Satellite T130 used pre-installed with Windows 7, and as we got him, he had a problem down.

  When I press Shut Down, it stops ok, all the lights go out as if it's just off and then a few seconds later, it starts again.
  I can't seem to find the problem here, sometimes it restarts perfectly in windows and other times it turns on and freezes without turning on the screen etc..

  I tried to update the BIOS, reinstall windows on a second partition, even reinstall all the drivers on the toshiba site.

  It should also be noted that when I put the system to sleep, he puts the PC to sleep and then a few seconds later, it restarts, raise the good old "an error has occurred, you want to start saving mode, start windows normally" etc.
  When you enter into hibernation mode, it hibernates it just find and then light up again...

  I read many forums for support and none of the solutions worked.

  Any help would be greatly appreciated!
  Thank you!

  Hello

  Have you checked whether the laptop computer power up again to to activated Wake Up we LAN and Wake on keyboard in BIOS option?
  Please disable it in the BIOS!

  In addition, go to the device-> LAN Manager card-> properties-> Advanced tab and disable options wake-up too.

  Restart the device and check again!

  Welcome them

• Started at Mo and not charging with the charger connected. Charger works. Keyboard not workin except power button / stop. Restarted using ex in car without success. SW

  Started MacBook and not charging with the charger connected. Charger works. Keyboard does not not except the power button / stop. Restarted ex drive no available help hoping that it was a matter of SW. SW and the operating system works very well. Read some info online. Tried to reset the SMC. Now, the MacBook does not start. Can U help me please. Thanks in advance.

  MacBook, 2010, Mac OS X 10.6.8

  Hi Veronica Steward,.

  I understand that you have turned into a series of questions about your MacBook and want help getting the computer to turn on. Here is an article that can help you through the steps to fix this problem:
  

  If your Mac will not turn on - Apple Support

  Let us know how it goes and thanks for coming to Apple Support communities.

  See you soon.

• Satellite T130: integrated webcam has stopped working

  Hi, I have the same problem of the bellows of the question, as I looked around and I was not able to find the answer I need.
  I have a Satellite T130 and, suddenly, the integrated webcam has stopped working properly. A blue light is on, but there is no picture. What can I do?
  Thank you

  Hi mate

  I have the same problem, sometimes using my U400.
  This happens if the room is dark for the camera.
  If something like this happens to you that I recommend that you keep your finger in front of the webcam for a short period.
  After that, the image of the webcam should come back again in my case it worked.

• 3 peripheral USB connected to the Macbook 4.1 computer tells me to restart using the power button / stop?

  I went to record a live concert, and I need to use a single interface to record the members of the group with microphones near directly to a computer and another interface running for my model of Macbook 4.1 end of 2007, to get signals from the map of the House.

  When I plug my converter USB 3.0 AD / DA in my Macbook 4,1 - the computer sends immediately a window indicating to me to "reboot" the computer using the power button / stop. Ideas or comments about why this happens?

  I read on this forum that USB ports should work with retroactive effect, or accept USB 3.0 devices, but just use a speed 2.0?

  Thank you.

  It could be that it is a requirement of your converter AD / DA she needs to be present at a properly accessible to the OS X when startup sequence it is plugged into a USB2 port.

  Its also interesting to note that, well that peripheral USB3 can be plugged into the USB2 ports... it could be that your device may not work properly unless it is used with a port USB3... for reasons of bandwidth or even certain types of power supply.

  But to be sure...

  Which converter AD / DA are you using?

• Satellite P750-02R - put on by button / stop

  My part number Satellite P750-02R PSAY3A-02R001 used to power on/off button, but will only start up by pressing the Play/Pause button on the control panel above the keyboard media.

  I checked the BIOS to V1.90 and done a system restore. A ran diagnostics and no luck, the laptop turns off not via the power button, and if anyone has any ideas, I would be happy, otherwise, so I have to take it back to Toshiba because it is still under warranty.
  Thank you
  Bruce.

  Hey Buddy,

  I'm a little confused about your ad first, you wrote that you can t turn on your laptop via the Start button / stop and you must write m notebook turn off via the power button not / stop. This confusion of s

  Anyway, you should turn on your laptop if you press and hold the s computer power button for a couple seconds.

  If you want to turn off your laptop with this button, you must configure Windows power management. You can define an action for the s computer power button if the laptop would shut down, sleep, Hibernate, or nothing. Don t forget this must be set for each plan of power if you change them.

• Satellite A200 AH3 stops instead of standby when I close the lid

  Hello

  I have a laptop Satellite A200 AH3. When I bought Windows Vista was preinstalled (I still drive recovery). When I closed the lid of the previous day (I mean the monitor turn off the HD, the cooling fan and all the rest). The light On / Off on the laptop turned to a flashing orange light.

  Then I opened the lid and Windows prompted me to the logon screen. This process occurred when the laptop starts on the battery, not when it is plugged. Everything was going fine.

  But I formatted the HD to install WIndows XP that I bought Windows vista seem to be too heavy for my laptop. So I installed Windows XP and the driver and the software available on the Toshiba site. Now when I close the lid, the Windows shut down very quickly (about5-6 seconds). However, it is a real firm. When I reopen it cover anything happen.

  Then I press the power button / stop and start Windows, normally (no screen saying that windows close annormally and no Safe Mode boot option). Even if I change the setting in the control panel/power Option or the Toshiba Power Saver, utility and I put them to sleep, he always make a stop down.

  How do I restore that?

  Hello!

  Have you downloaded the BIOS for Windows XP?
  For the Satellite A200, there are two versions available; one for XP and one for Vista.

  Also, make sure that you have the latest graphics card driver and keep your XP to date.

  Good bye

• Stop and restart buttons do not work

  There are about 3 weeks and co - either by the way, after installing some Windows updates, I could not long to shut down my computer or activate the restart function by clicking on closing down or restart buttons. The Hibernate button works.

  It is not related to firefox.

  You have any specific questions with the mozilla products?

• Satellite A300 - 15K - 2 media buttons stopped working

  Hello.

  I have a problem, the first 2 of my multimedia buttons stopped working...
  I tried to uninstall several times but it didn't help.

  I also have nothing to choose in the list in

  Toshiba Assist-> optimize-> Toshiba Button Support.

  I need help. (there were 2 posts before).

  Hello guys

  Can you please stop crying here, and perhaps tell us what the problem is here?

  Expensive J3... what you are writing about. What operating system do you use? What drivers? What kind of error?
  Multimedia keys are not controlled by drivers. What is - that you already tried?

  Hay metalbullet, the same questions for you - what order, what OS? Sorry, but you didn't offer any relevant information.

  Have you tried with this VAP suggested by Akuma?

• Satellite T130 - HDMI display does not

  Hello

  I'm trying to view my Toshiba Satellite T130 on my Toshiba 32 '' LCD TV, model 32BV702B, using an HDMI cable. The computer recognizes the TV and when you use desktop double or extended, the builtin laptop screen behaves as expected. However, the TV shows "No Signal" when the HDMI input is selected.

  We have another laptop with an HDMI output, and this configuration works very well. On two laptops, we use a 1366 x 768 display.

  Anyone know how I can get this working on the Toshiba laptop?

  Thank you.
  Ellie.

  (P.S. It seems that someone had a similar problem: [http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=205123]. In this case, the solution was to use a VGA instead of HDMI cable and the original problem has not been resolved. I really want to use my HDMI cable!

  Well, the other option attempts to retrieve the laptop using the HARD drive recovery or a recovery created with preinstalled Toshiba Recovery creator software image.

  I read that the other thread and the other user did not try this
  On the other hand, you can try to set the default BIOS and save the changes. Do not forget that the HDMI is it activated.

  Also, try this:
  Disconnect the battery and AC adapter
  Wait a few hours (3-4 hours) and then press the power button / stop for 30 seconds.
  Connect the two parts, and then test the laptop computer s HDMI.

• Satellite T130 - 10G Touchpad screen pointer gets stuck in random patterns

  Satellite T130 - 10G Touchpad screen pointer gets stuck in random patterns and laptop computer must be restarted to restore functionality
  The center of the causes of "touchpad button" toggle switch by pressing the touchpad pointer to enter a random State like two fingers to zoom.

  Sometimes, he'll be back to normal, but most of the time the computer should be put to sleep or restarted to restore functionality.

  a. I tried turn off all touch pad feature one item at a time and all, he still has some weird random State.
  (Did not try the impossible combination need $ to be interested but went to the 90% level)

  b. I tried disable the touch pad buttons offending and only using the mode tap the buttons and the problem still persist.

  c. Finally, tried bending the entire keyboard instead of pressing the buttons and it has also created the problem.

  This leads me to believe either the power key or flexion of the entire keyboard is originally is

  a. flexion of the touch pad causing the driver getting into a crazy State or require a recalibration.

  b. electrical connections causing the driver enter a crazy State or require a recalibration of bending.

  Note: I have reinstall the latest version of the driver.
  Also: American Toshiba support site that this problem exists in the notebooks of May.

  Also: The touchpad is too sensitive, which makes it very unusable!

  CAry

  Have you tried to install the operating system and check the functionality of the touchpad with the factory settings?
  Recovery image contains tested the touchpad and right and I don't think that helps the driver installation.