Sensor of acceleration on Tecra M4

Similar Questions

• NI9232 adapted to the PCB - 356 has 02 sensor of acceleration

  Hello

  I need to measure accelerations for a Test of 'head-Impact '. My boss has already ordered an acceleration sensor 3 dimensions (but only 2 dimensions required), which can be found here: http://www.synotech.de/produkte_skript/downloads/specs/356A02_specs.pdf .

  A Testengineer in my company (im a "student work" it) recommended the acquisition of data NI9232 for data acquisition, but I'm not sure if this is best suited. the +/-30V range is already too, so ill have amplify the signal of the sensor. But it is even possible to connect the sensor (not directly the sensor, but this power supply: http://www.synotech.de/produkte_skript/downloads/manuals/482C05_manual.pdf ) with a bnc connector? Article-he gave me, there were '782000-01', but this version didn't bnc inputs as much as I've seen.

  Im sorry if this post is a little confusing because I have little time.

  Best regards

  Alexander as

  With a 6 kHz of band bandwidth nealy all IEPE devive with 20 kHz samplerate and two channels will do the job.

  The 30V range isn't the problem, the resolution is still quite high, with about 2% to 5% uncertaincy residual resolution of the sensor 10-bit (8 bits) will do the job.  with a range of 60V and the output 10V range input (ok, say you sensor application only uses less 4V... you loose about 4 bits of your ENOBscards)

  The part of the slope is the connector

  The data sheet is a connector 4 pins 1/4-28. and NI IEPE devices usually have a BNC... If you need an adapter (ask synotech, or your boss has already ordered a )

• Can not find the device of sensor of fingerprint on Tecra A9-127

  When I try and regester my fingerprints, it said cannot find device fingerprint sensor. I installed the software protector suite ql and reboted the machine, but this message arrives.

  What model of laptop do you have?

  Have you downloaded the new software for fingerprints of the European driver Toshiba page and you reinstall it?

  I mean you must first uninstall the old software and then install the new one downloaded from the page.

• BB of Smartphones blackBerry with acceleration sensor

  Hello

  How will I know what Blackberry models have a sensor of acceleration? Is there somewhere a list, or all devices have an acceleration sensor?

  Kind regards

  Hi PtSyFr

  You can see all the BlackBerry models and offers a http://www.blackberry.com/smartphones. However, the models of the BlackBerry Storm and the BlackBerry Torch have accelerometers in them.

  Thank you

• Acceleration in the frequency domain

  Hello

  I enclose a vi that I already modified the existing example. I will use this vi to measure pressures (pressure sensor) and acceleration (from an IEPE accelerometer). Each of the two sensors is connected to a housed in a chassis CompactDAQ C Series module connector 4. The pressure sensor measures the pressure of the water flowing in a pipe while the accelerometer will simultaneously measure the vibration of this pipeline caused by the fluctuation of water pressure. In this vi, I am connecting a signal of pressure and acceleration TDMS file and then read the two signals on the cards of distinct waveform. The acceleration signal is written and read in the time domain. I need your help to make change more on this vi to take the acceleration signal and read on a separate table in the field frequency and written also the frequency of the field values in a file of PDM. After this change, the vi is supposed to have three graphics of waveform (pressure, acceleration time-domain and acceleration in the frequency domain and opens two tdms files, one for pressure and acceleration in the time domain and one for acceleration in frequency domain.)

  I tried many ways all failed because I'm not very familiar with the measurements of vibrations.

  I thank in advance.

  Hello

  It is important that you should decide if the frequency data you are interested in are constants based on time, or if you need to know how the data of frequency changes over time.

  For constant frequency over time, take a look at the Fast Fourier Transform: http://www.ni.com/white-paper/4541/en/

  If you need to know how the frequency display, take a look at the analysis of the frequency of the common time: http://www.ni.com/white-paper/3548/en/

• HP ENVY 15-j151sa: HP Hard Drive protection software 3D

  Hello.

  After you have reinstalled windows, I not recognized device

  ACPI\HPQ6007\3 & 2411E6FE & 0

  I managed to find it's a HP 3D HD protection device thing – I'm guessing sensor of acceleration?

  and if I'm correct required driver is sp67280.exe

  I swapped the HD with the SSHD manufacturers so it seems a bit pointless to install in particular that it is quite as he would have a negative impact on the performance of the PC.

  What do you think? Would it not be better to ignore the unrecognized device or install this useless from my point of view function, since it could be used by other components and lack of it may have a negative impact on the performance actually?

  Hello:

  I like a 'clean' Device Manager

  The software of the unit doesn't bother the performance of the laptop.  Is not a very large file.

  I installed it on my HP Elitebook 6930p, who runs a 330 of Intel SSD, and I can tell you that I noticed zero negative impact on disk or laptop with 3D driveguard installed.

• Tecra A7 fingerprint sensor support

  Hello!

  A skier of Tecra A7 have a fingerprint sensor and some not. How will I know if my A7 has a sensor? There is a quarter on the right side of the touchpad, but it has the same color as the case of notbook.

  Hello

  Where did you come from?
  There are many models Tecra A7 but each model has been designed for a country or a region

  You can visit the Toshiba home page and check the area of product-> notebooks-> Tecra

  There you should find different units of Tecra A7 and the features supported.
  But as far as I know, that Tecra A7 with number PTA71C should support the fingerprint reader.

  By the way every mobile merchant who sells the Tecra A7 should provide or offers the right information on the details of the laptop

• Tecra M5 - can't find the fingerprint sensor

  I have Tecra M5 with Windows 7 and I'm putting software fingerprints (protector suite QL) but old version is not compatible and new (taken from the Toshibas site) do not work. It just says: 'cannot find code 0xe7210005 of the fingerprint sensor device '. material is integrated.

  In the system's peripheral unknown ACPI\TOA620A, but it cannot be updated. Windows cannot find drivers and support package (driver_fingerprint_upek_TC00237700A) or (2.19C_package) has no driver that should be?

  Hi monono.

  Did you remove the old version of the fingerprint software before installing the new version? Remove from Control Panel > uninstall programs and remove the software before installing a new. Also use a registry cleaner like Ccleaner to clean the registry.

  Fingerprint work with OS preinstalled Toshiba?

• Tecra A11 - 11L - fingerprint sensor does not work

  Hello
  I had a problem with my Tecra laptop. The fingerprint sensor does not work since yesterday. It also disappears from the hardware Manager. I tried to reinstall the utility, but the setup.exe will not run successfully. When I try to install the utility directly from the amd64 Directory installation will be successful, but the software is unable to connect to the fingerprint sensor. I also tried to install the original Windows image, but the sensor does not work.

  You have any ideas?

  Berst cordially
  Thunder1988

  You can try a BIOS update and set the default BIOS. If it still does not appear in Device Manager, the player is maybe defective or there is a connection problem. I'm guessing that the laptop is still under warranty, you may have to send the laptop to a Toshiba repair center.

• Tecra A9 - fingerprint sensor does not work

  My Tecra A9 is less than 2 weeks old. The first day, the fingerprint sensor worked for a few hours. I registered three fingerprints. Since then when I drag my finger, 99% of the time it does not recognize or gives a message 'too short', although I followed the steps in the tutorial.

  There is a window where you can test the fingerprint sensor trying to drag prints. I asked the other two persons, of different ages and gender, to try it, but very rarely is he not successfully registered printing.
  My call to the support wasn't very helpful because I was threatened with charges of £35 if they find nothing wrong with the hardware. As a normal user, is not what it says on the Tin.

  Has anyone had the same problem and managed to resolve it. If so, how? If not, are there other people in the same situation?

  Hello Assa

  It's very strange. I didn't notice any problem on my Tecra. Please start Fingerprint Control Center and check the first option that it fingerprints. Under registration or change fingerprints, you will find option run interactive tutorial with exact explanation how to use the fingerprint sensor and your fingers correctly.

  To be honest, I do not think you have a hardware or software problem, but you must be careful how you drag your finger.

• Tecra A8: Fingerprints - 1080 biometric sensor sensor is not calibrated

  Hello

  I recently installed the software (Protector Suite QL) on my laptop Tecra A8. It worked fine for a day! Then I get an error saying ' biometric sensor is not calibrated, please use calibration tool to rememdy it "when I try to enter some impressions more. I can't seem to find this tool and I tried to uninstall and reinstall and it doesn't work. Any ideas on how to solve this problem?

  Thank you

  Hi Rainer

  Have you checked if this option is located in the Protector Suite QL application?
  Eventually it s a part of this software.

  Where did you get this program and has been this application preinstalled on the Toshiba recovery image?

• Libretto W100: Access to acceleration sensors

  I would like to do shows with the G-Sensor.
  How can I access it?
  Is there any help?
  What is the driver and the name of the sensor?
  It does not appear in Device Manager.

  Hello

  It seems that the capacitive multi touch sensor is provided my Wacom.
  Google a bit and found this:
  http://www.Wacom-components.com/usingWacom/

  Welcome them

• Tecra M5 - 50th and Win7 - need driver for Biomectric sensor

  Hello

  I installed windows 7 Home Pemium and all the drivers on the toshiba site.
  In the end two problems persist:
  (a) the biometric sensor software is installed, but the sensor is not detected. When the stars of windows appears a taskbar balloon saying "Connect Biomectric sensor into the USB;
  (b) remains an unknown device in Device Manager. I don't know if about the biometric problem. If not, how can I find out what it is?

  Thank you
  Best regards
  Hugo Pinto

  I presume that this unknown device must be connected to the sensor.
  Check the hardware ID and check with http://www.pcidatabase.com/

  http://APS2.toshiba-tro.de/KB0/HTD0302U00000R01.htm

• Tecra Z50 - utility of fingerprints can not connect on the sensor

  Although the latest version of the driver for validity sensor is installed the fingerprint utility cannot connect to the sensor.

  System: Win 8.1 64-bit

  You should put a little more information on your machine.
  Are you using the version Win8.1 as recovery image original Toshiba?
  I guess that if you use the laptop with the factory settings, everything should be OK.
  Have you noticed this problem with the original driver?

• Tecra A9 - software for the fingerprint sensor error

  My laptop is less than 3 weeks old and the fingerprint sensor has stopped working.
  I just get an error message: can not find the fingerprint sensor device, 0xe7210005 error code.
  can anyone help?

  Hello

  you don't have many options. But I can try to give you some tips:

  1. go into the Device Manager and search for the device of fingerprints, so if it s present, uninstall it and after a reboot it should reinstall itself.

  2. go on Toshiba drivers download site and download the latest drivers for this device. Install the driver and check if it work s

  3. If really nothing done then you should recover your machine with the media shipped (or HARD drive recovery)

  4. the last resort, if all fails, is to contact the nearest [ASP | http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_whitepaper.jsp?service=EU&WHITEPAPER_ID=0 000000871] in your country and ask them a hardware health check and repair.

  Good luck

  Greetings