Series RS-232/485 isolated 2-port not recognized PCI card

I have a series RS-232/485 isolated 2-port PCI on my computer. I installed the card, then the software but my computer never acknowledged that there is a card in the PCI slot. Because this card is old, I also tried to install older versions of the software serial but it did not help. I have a Windows 7 computer x32bit and other PCI cards have been installed into the same slot before this one, so I know the works of slot. The map was built well before Windows 7 and I don't know if they are compatible. I was wondering if there is no way to force the computer to recognize the hardware or if there is a way to check to see if the card still works.

Thank you

Tags: NI Hardware

The problem

I can't use the connect command:

/Admin1-> connect com2
cmdstat
status: 2
status_tag: PROCESSING COMMAND FAILED
error: 253
error_tag: COMMAND NOT RECOGNIZED

Configuration

Version

BIOS is 6.1.0, cli version output is:

/Admin1-> version
CLP SM Version: 1.0.2
SM ME treat Version: 1.0.0b

I have configured the redirection as before:

BIOS

Communication series	On with the Console via COM2 Redirection
Address of the Serial Port	Device1 Serial = COM1, Serial Device2 = COM2
Connector external series	Remote access equipment
Failsafe baud rate	115200
Remote Terminal type	VT100/VT220
Redirection after boot	People with disabilities

iDRAC

/Admin1/system1/SP1-> racadm config-g cfgSerial o cfgSerialBaudRate 115200
Value of the object successfully changed
/Admin1/system1/SP1-> racadm config-g cfgSerial o cfgSerialConsoleEnable 1
Value of the object successfully changed
/Admin1/system1/SP1-> racadm config-g cfgSerial o cfgSerialSshEnable 1
Value of the object successfully changed
/Admin1/system1/SP1-> racadm config-g cfgSerial o cfgSerialHistorySize 2000
Value of the object successfully changed

The command is now console, not connect.

And that's exactly what is said in the docs - it's just that I had not noticed the change and read 'connect', where 'console' was written.

A big thanks to Lars Handrick Support Dell Germany for reporting the change of command name for me.

HP 251-a123w: DVI - D port not recognized

I have a HP Desktop 251-a123w which was delivered with a 22uh HP monitor. Only a VGA cable was included, but HP 22uh monitor has HDMI, VGA and DVI - D ports. I use the system with the monitor connected to the VGA cable until Saturday.

Saturday I shut down the computer and the 22uh HP connecting its port DVI - D port DVI - D on the computer using a DVI - D cable. Then I connected an Acer X193w monitor is VGA port on the VGA port of the computer using a VGA cable. I want to have a Setup dual monitor. HP support for my model site indicates that both ports can be used at the same time.

Well, my computer starts by using the Acer monitor to the VGA port but the HP 22uh simply displays a message "Not connected Signal Cable!". Nothing I did make the HP 22uh start on the DVI - D port.

I've updated the drivers, I rebooted the computer several times. I started the computer with only the monitor 22uh HP connected through a DVI - D cable and still do not recognize the monitor. I uninstalled the display adapter and then restarted, is yet to recognize the DVI - D port (or maybe that the monitor is not recognizing cable, I don't know). I have the HP 22uh monitor turned off and restarted, still nothing.

Any suggestions?

OK, dug the manual out of the garbage, "Input Select option in the OSD menu.

Had no experience previous selection of entry on a monitor... Who reads the manual for a monitor? SMH

USB not port not working and card reader doesn't work is not on my desk.

My usb port and built-in card reader does not work on my desk, also my external speakers do not work. stakeholders work with my laptop, it is not connected via USB.

Hi yankee7,

· You receive an error code or error message when you connect a USB device?

· Do you remember recent changes made to your computer before the show?

· What is the number and the model of the computer?

· What is the service pack installed on the computer?

Check the status of the device in Device Manager. Follow the steps below:

a. click on start

b. in the run box, type in devmgmt.msc

c. expand USB bus controllers

d. check if no yellow bang is listed (double-click on the device with a yellow bang for the error code)

With regard to:

Samhrutha G S - Microsoft technical support.

Visit our Microsoft answers feedback Forum and let us know what you think.

USB ports not recognized anymore

I have Vista. USB ports and ports that accept cards camera no longer recognize them. Scanner can be moved from USB port to the USB port and works but "Explorer" does not show that they exist. How to recognize camera cards (mainly) as they did before? Windows offers device (camera card) has a problem, but this isn't the case. Card works so executed through camera (USB cable to the USB port) in two different cases with two different cameras. Also plugged on the USP port scanner is not recognized by the function 'Explorer' but actually works very well.

Hello ghpots,

· What happens when connect cards camera on USB ports, it installs the device drivers?

· What are the changes that you made to your computer, since it has stopped working.

When you connect your devices to the USB ports, check the status of the device in the Device Manager. Check if you see a yellow fringe or exclamations in the Device Manager.

I suggest that you remove and then reinstall all USB controllers.

To remove and reinstall all USB controllers, follow these steps:

1. click on start, type Device Manager and open the Device Manager.

2 right-click every device under the Bus USB controllers node and then click on uninstall to remove them one at a time.

3. restart the computer and reinstall the USB controllers.

Plug in the removable USB storage device and test to make sure that the problem is solved.

Check the Device Manager to see if the unit under section USB or other devices. To do this, follow the procedures below:

Method 1:

1. click on Start, right click computerand select Properties .

2. click on Device Manager.

3. click on the (+) sign next to Universal Serial Bus controllers and next to the peripheral plus other section.

Look for the USB device under the Universal Serial Bus controllers, or under the other devices section.

4. If the unit is under Bus USB controllers or other devices, click on the reference to the 'unknown' device name, and then click Uninstall to remove the device.

5. close Device Manager, and then restart the computer.

6. If the USB device that has problems with software and it has not already been installed, install the software, now follow the planned manufacturer of the directives.

7 reconnect the USB device that had issues and test to see if it works.

The unit should now work correctly. Continue if the device name is not found in the Device Manager.

Method 2: There may be a problem with the USB port. Try connecting to a different USB port. If the USB device is displayed in Device Manager after plugging the cable in a different port, then uninstall and reinstall the software of USB device driver.

Method 3: Check the manufacturer of the device for support if the device is still unable to display.

Thank you
Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know what you think.

BlackBerry Smartphones BB Pearl not recognizing Media Card

I have a Kingston 2 GB MicroSD card installed in my BB. He works very well for the past month (since I have the phone) and has 4 or 5 images and 5 another 6 ringtones stored on it. Earlier this week, I had been hanging the phone to the computer with the USB cable and it would ask me if I wanted to access the media. I would say no and continue on from there. Then Wednesday, all of a sudden the BB began to no longer recognize the card. Today, I went into the settings and they are:

Map of media Support - on

Encryption mode - no

Mass Storage Mode Support - on

Auto enable mass storage Mode when connected - invites

A memory card is not currently inserted in the device.

I take the media card and plug in the computer and it is still showing all the files there. When I plug the phone to the computer, it is not recognized by the computer.

Any suggestions?

I found something Spingineer here (http://supportforums.blackberry.com/rim/board/message?board.id=8100&thread.id=11781) and tried. It worked like a charm.

Pavilion 17-g192dx: USB Ports not recognized

Hello

I have a HP Pavilion 17-g192dx that's installed with Windows 10 factory. I decided to give the new operating system a go, but was overall very satisfied with his overall performance and updates of buggy. Not wanting to give up the new machine, I decided to bring it back and oldie but a goodie - Windows 7. I got a copy of Windows 7 Home Premium lying around so I gave a go and installed the operating system. I got the internet running successfully and in no time most of my drivers have been installed. The problem that I face now is that the old BONES will not work with my USB ports. I do not use a hub and have almost exauhsted the drivers for this Web site section. If someone wants to kindly point out how I could go about fixing this issue, any help would be much appreciated.

I'm not as interested to get back to Windows 10. It is too slow for daily use (ma) and buggy.

Thanks in advance!

Hello:

Download, unzip and run the file setup.exe from the link below...

https://Downloadcenter.Intel.com/download/22824/USB-3-0-driver-Intel-USB-3-0-Extensible-host-controller-driver-for-Intel-8-9-100-series-and-Intel-C220-C610-chipset-family?product=65855

USB ports not recognized on the computer.

erased win 8 and reinstalled win 7 ultimate. Now computer will not recognize and usb ports. What should I do?

I use a Compaq Presario 5320. USB works, that I plug my Saitek yoke and it works correctly. It's only usb drives I plug in I get the message, that he doesn´t recognize...

TA

The problem with coming back to win 7 is may or may not win 7 drivers. I would contact Compaq to see if there is win 7 drivers.

Another problem if your computer comes with win 8 pre-installed revenant may void the warranty

USB ports not recognizing keyboard and the mouse after sleep

I have a wireless Logitech and mouse keyboard. These connect to my PC (Vista32) wirelessly via a USB plug small heel I plug into a USB port. Logitech called "Unify" which, according to them, is standard to connect devices through a USB port. My mouse and keyboard work fine when I restart my computer, but when he goes to sleep and I me re - wake up there that they do not have. I force power off of my computer because I can't access my account.

I have ensured that the selective suspend setting in settings usb in advance power settings is disabled. Support Logitech seem unable to help him.

Hey Sinclair,

You can refer to this link suggestions and answer us with the State of the question.

A USB device may no longer work correctly when Windows Vista comes out of standby or hibernation

http://support.Microsoft.com/kb/928631

Also refer to this link: How to troubleshoot USB device problems that can occur after a PC that is running Windows 7 or Windows Vista from sleep or hibernation resume

http://support.Microsoft.com/kb/953367

Registry WARNING: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, see this link:

http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

I hope this helps.

USB ports not recognizing devices

USB ports for laptop Toshiba Sateliite do not recognize camera or other devices?

Hello

Check the configuration/settings (BIOS/CMOS) often F2 when you start - make sure that USB is enabled.

For a laptop, using a real computer shop (no leeks and glances at a Best Buy or other large surfaces)
Stores) or system manufacturer support.

Check with Toshiba support, their drivers online (update or reinstall) and their forums.

Toshiba - Forums
http://laptopforums.Toshiba.com/

Toshiba - Contacts
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/navShell.jsp?CF=su_contact

Toshiba - drivers - access your model
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=download

Toshiba - Support
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

------------------

Follow these steps to remove corruption and missing/damaged file system repair or replacement.

Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

sfc/scannow

How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228

Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

-----------------------------------------------

Then lets refresh the USB stack

Control the click Control Panel - Device Manager - no matter where in the box of white/white - then the VIEW - see the
Devices disabled - look around (with the exception of USB controllers) for your devices (can have
zero or more than one) and top - right click UNINSTALL.

Control Panel - right CLICK on EVERYTHING - Serial USB controllers - Device Manager and UNINSTALL
all except the category itself - REBOOT - it refreshes the drive and battery USB

This KB shows XP how to and the method of Vista is identical
http://support.Microsoft.com/kb/310575

This is a utility to help you, but do 1 above.

USBDeview is a small utility that lists all USB devices currently connected to your computer, thus
as all USB devices that you previously used. Run Options and check the 1st three choices to see to it there
Is there.

http://www.NirSoft.NET/utils/usb_devices_view.html

You must remove all instances of the devices and restart.

----------------------------------------------

If necessary try these two:

Tips for solving problems of USB devices - and a Mr Fixit
http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

Hardware devices not detected or not working - Mr. Fixit
http://support.Microsoft.com/GP/hardware_device_problems

I hope this helps and happy holidays!

Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

Satellite C650 - USB ports not recognized in Device Manager

When I turned off my cell phone, I lose the use of my two USB ports. The only way I can get back them is to use Device Manager

Go into the Manager of peripheral devices, Bus USB controllers, there are 6 x Intel ICH9 Family USB Universal Host controller 2 x Intel ICH9 Family USB2 Enhanced Host Controllers and 7 x USB hub root. When I lose the USB ports, USB root hubs seem to disappear, and the only way I can get back them is to uninstall the controllers and then right-click Universal Serial Bus Conrollers for "scan for changes on the hardware. This brings back the root hubs and USB ports work fine... until the computer turns off again.

Someone at - he encountered this problem and managed to resolve it? Its a hassle to have to go through the uninstall it / Reinstall procedure each time. Your advice will be appreciated.

Hey Buddy,

You use the version preinstalled Windows from Toshiba or did you install your own version? I don't see any information about the BONES in your ad...
Theoretically, it could be a software problem so ports USB work correctly if they recognized in Device Manager

You should also try to update the Web from Toshiba site chipset driver. Maybe it helps.
Otherwise, I could imagine that the update of the BIOS can also operate and this update you can get on the Web from Toshiba site too.

After update BIOS USB Ports not recognized on Satellite L500

Hello!

After a BIOS update to 2.1, two of my three USB Ports no longer work. Is it possible to downgrade to the previous BIOS? Or what else could cause this problem?

The system is a Satellite L500 - 153 (PSJ3E)

Post edited by: koocho

Go to Device Manager.
Remove all USB hubs and USB controllers in the list of devices.
Restart the computer and wait for Win has recognized and installed again all USB devices.
Then test the USB feature.

USB ports not recognizing any device

I plugged into multiple items - iPod, iphone, USB keys. Nothing is recognized.

Hi kslicho

1. What is the exact error message you get when you try to access devices?
2. for how long have you been faced with this problem?
3. have you made any recent changes on the computer?

Method 1:

You can even check if you get the error messages for the devices in the Device Manager. Please refer to the below steps.
a. open the Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
b b.. in Device Manager, look for the device and then right click on the name of the device and go to properties.
c. now on the general tab, check the status of the device. Let us know the status of the device. Also you can inform an error code with the State.

Method 2:

You can even check if uninstalling and reinstalling USB drivers to connect the hard drive. You can disconnect all USB devices and then perform the following steps:

a. click Startand then click Control Panel.

b. click system and Maintenance, click Systemand then click on Device Manager.

Note If Control Panel is in Classic view, double-click System, and then click Device Manager.
If you are prompted for an administrator password or a confirmation, type the password, or click allow.

(c) in the Device Manager, double click on extend "Controllers of Bus USB", right click on the host
Controller, click "Uninstall" and then click on 'OK '.

d. Repeat step 2 to uninstall all items under 'USB Bus controllers'.

Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

I hope this helps.