set up to bring the Fibre Channel between UCS of interconnection fiber and Nexus 5548UP.
by using the following configuration between Nexus5k and UCS FI. the status of channel comes to ini and change to notConnected.
-------------------------------------------------------------------------------
FC1/31 431 notConnected swl - 100 F
FC1/32 431 notConnected swl - 100 F
-----------------------------------------------------------------------------------
The system version: 5.2 (1) N1(1b)
1 on FCoE
1 active FEX
active toy-channel-trunk 1
interface vlan 1 on
1 active LACP
1 active LLDP
1 active NPIV
1 active sshServer
1 on GANYMEDE
1 active telnetServer
Uni-directional active 1
1 active VPC
san-port-channel interface, 100
active channel mode
switchport mode F
switchport trunk allowed vsan 431
interface fc1/31
switchport 'SAN PO to UCS - one' description
channel-group 100
no downtime
interface fc1/32
switchport 'SAN PO to UCS - one' description
channel-group 100
no downtime
interface fc1/31
switchport mode F
interface fc1/32
switchport mode F
Help, please
You must update your 5 k at least
6.0 (2) N1 (2)
Tags: Cisco DataCenter
Similar Questions
-
I was wondering if it really is possible to have the Fibre Channel frames running on a UCS?
I read these two articles that provide some great information on the implementation of the Fiber Channel Jumbo and Jumbo frames:
http://datacenteroverlords.com/2013/04/01/Jumbo-FC-frames/
http://www.ccierants.com/2013/10/CCIE-DC-definitive-Jumbo-frames.htmlEverything in the SAN I'm administration has the ability to set the MTU value until 9036 except for the UCS. For example on NetApp train I can set the MTU by interface on the Cisco MDS I can set the MTU by vsan. However in the UCS Manager when I go to class of service of system quality, the option to set the MTU of Fibre Channel value is grayed out and it doesn't look like there is in any case override the preset frame size. I can set the MTU of the best Effort however my understanding is traffic Fibre Channel in the UCS will use the class system of Fibre Channel.
Also I noticed that I can set the maximum size of the data on the vHBA field in the UCS Manager but my understanding is the maximum that can be up to 2048.
Hello
Have you checked
http://datacenteroverlords.com/2013/04/01/Jumbo-FC-frames/
Erik Smith says:April fool! I wish I saw this earlier, I would have posted corroborating results!
In short: Forget the CF frames!
-
my dvd will not play after you have uninstalled an editor audio wave pad. Is there a way to fix my dvd without reinstalling the program? I received the following message, (Windows Media Player cannot play this DVD because there is a problem with the digital copy between your DVD drive decoder and video card protection. Try to install a driver available for your video card).
my dvd will not play after you have uninstalled an editor audio wave pad. Is there a way to fix my dvd without reinstalling the program? I received the following message, (Windows Media Player cannot play this DVD because there is a problem with the digital copy between your DVD drive decoder and video card protection. Try to install a driver available for your video card).
================================================
If the uninstallation of software caused the problem... it may be worth trying to
do a system restore to a time before the software has been uninstalled:Windows 7 system restore: frequently asked questions
http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions -
Setting port channel between UCS - FI and MDS 9124 (Mode F)
Dear team,
We tried to create the channel of port between UCS FI and MDS 9124
But the port channel do not take action in mode F on MDS 9124
FI is in host FC end Mode
We have allowed FC uplink on FI trunking
We have activated NPIV on MDS
We have activated the MDS trunk
FI and MDS in default VSAN
To check that we have changed the way FI FC channels mode and switch port became active, but in E mode
When we enabled CF trunking of uplink on the port mode FI channels and FC Switching became active in mode TE
but in both cases above, showflogi database shows WWPN of SAN alone does not have the any fi.
How to achieve this?
Have read that no need to change the mode switching mode of CF swicthing and keep FC Endhost way
SO how to channel ports with mode F MDS and FI (Display Mode as NProxy)
What is it has nothing to do with the MDS NX - OS version? (https://supportforums.cisco.com/thread/2179129)
If yes how to put as license for ports came with the camera and we don't have any CAP/PAK or license file as she came
with license
Also, we saw 2 files available for download (m9100-s2ek9-kickstart - mz.5.2.8 .bin and m9100-s2ek9 - mz.5.2.8 .bin b b) to use
Thanks and greetings
Jose
Hi Jo Bo.
What version of the software if your MDS race?
On your UCS do connect nxos and show ficelleStringString ficelleT inteface and find the mac address.
It is possible that you could be hitting the bug below. If this is the case, you may need to update the firmware on your MDS.
Add MAC YES '002a6a', '8c604f', '00defb' for 5 k/UCS-FI
http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId= CSCty04686
Symptom:
Link change cannot connect any other Nexus or other Cisco Switch in mode VAN with a port channel F. Question can be viewed in older versions of 5.1
5.1.3.N1.1a
but not later
5.1.3.N2.1c
Release. Question is also found in
5.2 (1) N1 (1)
and
6.0 (2) N1 (1)
and later versions.
Conditions:
Nexus configured for the link SAN PortChannels or NPIV Nexus mode connected to the UCS via regular F port channel where UCS VAN VAN edge mode switch: YES switch manufactured FI or another Cisco UCS Port WWN: xx:xx:00:2 has: 6a: xx:xx:xx or xx:xx:8 c: 60:4f:xx:xx:xx
Workaround solution:
Turn-off on Nexus 5 k TF-port question link mode does not happen with standard F-PORT SAN to remove Portchannel config
Other Description of the problem:
To check question collect please see the flogi-event history internal errors whenever the port is attempted OLS, AMENDMENTS, PBA counters will increment. This can be determined via the following output, view port internal info to see all the internal-historic port of error events
-
How to set a solid as the Alpha channel?
Hi all
At my wits end on this. Seems to be a basic after effects thing, but I can't find seem to find the answer online or on these forums. Maybe I'm he read the wrong way. Well, here we go anyway...
A layer inside my computer is a solid red. This solid has a mask on it, while the visible part is only a red circle.
Now all I want to do is tell AE that when it restores this model as a QT Animation, the solid red is the alpha channel. Seems simple enough, right? What is the right way to do it?
Thank you!
As you may have guessed, it's easy and you will find that you use much - basicallly, whenever you want to hide something, but not a not the mask move with the layer...
The solution:
First of all, make sure you have column mattes expanded on the timeline (small box below on the left mask/shows this). Place solid directly above the layer you want to mat (if you have a lot of layers, you precomp it).
Then, on your layer of film (below the solid), the value of the Alpha cache - which will be Matt on this layer based on the alpha of the layer above it.
Alternatively, you can use an effect, in my view, that is define Matte, and then select the matte layer.
A method other than Milenium often mentions, but I've never used is to assign the matte layer silohuette alpha - I think the mat layer must be defined as an adjustment layer.
-Dave
-
Hello, thanks for reading and helping me.
I try to play a legitimate, belonging to DVD, but Windows Media Player 12 will not play on my computer Windows 7 Professional. The DVD worked a few days ago, but all of a sudden, I get the following error message:
"Windows Media Player cannot play this DVD because there is a problem with the digital copy between your DVD player and the video card protection decoder. Try to install a driver available for your video card.
I did a lot of research of these forums and on the ' net. Here are the suggested steps I tried without success:
- I tried VLC player. This works. However, rather than use this workaround, I wish to find a solution to my problem WMP/WMC.
- I tried several DVD for years over the last decade. These DVD works on my laptop, also running Windows 7 Professional and the shark 007 codec.
- I uninstalled my Shark 007 codec
- I tried other codecs (K-Lite)
- I assured that the latest drivers are installed on my video card, XFX ATI Radeon 5850
- I tried to uninstall Nero 9
- I tried to use the Windows 7 troubleshooting options:
- > Reading and burning CD, DVD and Blu - ray (no problem)
- > Windows Media Player DVD (no problem)
- > Windows Media Player Settings (detects a problem, wants to restore factory settings, every time, no matter what happens)
- A system restore to a time when the DVD was working did not resolve the issue
- The different links in Microsoft, I found in this forum about this problem do not seem to be useful. There is a link that points to the set-top boxes, but this page just says: "Windows 7 comes with a decoder.
- I assured the latest driver is available by going to "Device Manager", right click on the drive, then click on "update driver software".
- I assured that the latest firmware is installed directly from the manufacturer's website.
- I tried to reset my DRM by renaming the DRM under C:\ProgramData\Microsoft\Windows folder and by going to this Web site to upgrade:http://drmlicense.one.microsoft.com/Indivsite/en/indivit.asp?force=1
- I've uninstalled and reinstalled Windows Media Player 12 and Windows Media Center via the function "functionality in Windows.
I would be very grateful if a Microsoft technology could chime. Thanks for your help!
MY COMPUTER:
DVD drive: TSSTcorp CDDVDW SH-S203N ATA Device (Samsung)
Driver: Microsoft 6.1.7600.16384, dated 06/21/2006
Graphics card: XFX ATI Radeon 5850 Black
Motherboard: Gigabyte GA-X58A-UD3R
Processor: Intel i7-920-Intel i7-920, Corsair 6 GB of RAM, ATI Radeon HD 5850, Gigabyte GA-X58A-UD3R, Corsair 800 d case
Hello
Try this free program:
http://www.DVDFab.com/passkey-Lite.htm
Carlos
-
Original title: unable to play any DVD
"Windows Media Player cannot play this DVD because there is a problem with the digital copy between your DVD player and the video card protection decoder. Try to install a driver available for your video card.
I tried to update all the drivers but the problem persists
Hi Neil,
1. have you made any hardware changes or software on the computer before this problem?
2. what version of windows Media Player do you use?
You can follow this link & check if the problem persists.
Windows Media Player Error Message help
Reference: How to troubleshoot issues that occur when you play a DVD in Windows XP?Hope the helps of information.
Please post back and we do know. -
This is the message that I faced when I tried ti a watch a DVD I've seen countless times in y HP laptop. I read some answers here, but I do not understand something they are trying to say. I'm not technologically minded so pleaaaase can someone tell me what is happening?
Hi Abigayi lMcFadyen,
To prevent the illegal creation of digital copies of DVD, information on most of the DVDs are blurred. Your DVD decoder and Windows Media Player have software to copy protection that decodes the information on the DVD just before posting. If this software does not start successfully, you may receive this error.
Method 1: You will have to perhaps download and install the latest plug-in to do this, see the link below
http://Windows.Microsoft.com/en-us/Windows/downloads/Windows-Media-Player/plug-ins
Note: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.
Microsoft provides third-party contact information to help you find technical support. These details may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
The third-party products or services mentioned here are manufactured or provided by companies that are independent of Microsoft. Microsoft makes no warranty, implied or otherwise, regarding the performance or reliability of these products.
Method 2: You can see the steps in the link below by Shinmila H
-
The dictionary is English: center USA, color, fiber, and yet are misspelled
Hello
I just checked and my dictionary is set on "English: USA" even spellcheck guard American vocation of the spellings of words such as color, Center, and fiber and suggest what I think are traditional spellings UK (color, fiber, Center) of these words. Anyone know what could be wrong or how I can fix this?
The language is an attribute of character level. Check your text to see what language it is.
-
What are the functional differences, if any, between MS detours and the alternative open source EasyHook?
https://easyhook.github.IO/index.html
This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)* -
Can I disable the B200 blade Fibre Channel vHBA
Hello
I'm setting up my service to my B200 blades profiles and I was wondering if there was a way to disable the Fibre Channel HBA. I will not use CF as all my iSCSI storage.
Thank you
LTA
When you create a service profile, you are asked if you want the storage (= CF) or not; you say no!
If you missed this step and you have created vhba, just remove them later.
It is not possible to disable vhna.
-
Uplink Ports Fibre Channel - UCS GUI Configuration Guide
Hi all
Could someone please explain which means that what follows in the Configuration of GUI of UCS guide @.
Uplink Ports Fibre Channel
Manage ports Uplink Fiber Channel FCoE traffic between the interconnection of fabric and the next layer of the
SAN storage network. All FCoE network-related traffic is pinned to one of these ports.
By default, the Fibre Channel ports are uplink. However, you can configure them to work as Fibre Channel
storage ports. This is useful in cases where a Cisco UCS requires a connection to a DAS storage
Device (DAS).
My question is, how the FC Port could handle FCoE traffic? My understanding was that FCoE will be lifted and Enthernet connection only.
Thanks for your help
Concerning
Vikas Srivastava
The CF module interconnection fabric is the place where the speration of CF vs. FCoE happen, so it's where the FC frame is extracted in the Ethernet frame.
-
Total for the port-channel when speed config speed 1000-nexus5548?
Hello world.
now I connect cisco 6509 and nexus 5548up using two link of 1000M and I want the two link port-Channel binding.
5548up port 10GE port cisco 6509 is 1GE, I config speed 1000 in nexus5548 ethernet port, and I find
the speed 1000 order auto config interface port-channel, so I would like to know the total speed in this channel port
is 1000M and 2000M when port-channel speed config 1000? I appreciate your help!
the topology like this:
1000M
--------------------------------------------
6509 port-channel speed 1000M nexus5548UP
----------------------------------------------
1000M
Hi again
The speed of the links and portchannel is 1000M but the bandwidth of the portchannel is 2000M
-
Live migration between servers Intel Xeon E5410 and Intel Xeon E5506?
Hello.
Is it possible to run the dynamic migration between servers Intel Xeon E5410 and Intel Xeon E5506 processor?
Both servers are running ESX 4.0
Try to migrate will cause an error as UC and hostbitys do not match.
I; m impossible and VCA (like a Core2 family and another family of Core i7).
I don't mind to give up a part of the 'new feature' the Core i7.
Thank you
Zeevik.
> I; m impossible and VCA (like a Core2 family and another family of Core i7).
You must turn off all the virtual machines on the host with 55xx Xeons before turning on the VCA.
---
MCITP: SA, MCTS Hyper-V, VMware vExpert, VCP 3/4
-
Emulator of the UCS and Fibre Channel (PCI Passthrough)
Hello
I would like to know if anyone of you knows if emulator UCS supports CF communications and how to configure them.
I have 2 PCI Fibre Channel interfaces on the host Hardware and I applied PCI Passthrough on the ESXi hypervisor. It works with other virtual machines.
Thank you very much
Francesco
No, unfortunately not.
Maybe you are looking for
-
I have FF 40.0.3, Win 10, FF will minimize and not recover.
When working on other things and FF is open, click on the tab in the taskbar does not restore FF. Can I close all other windows, but FF will not return. The only way I found out how to restore it is close FF then re-open and restore previous session
-
After dialing an email I still don't know how to send button TI - no
Since the change, no matter what I try, I can't have a button 'send' of any kind. The menu bar does not help. I literally spent hours (market) to try to get some sort of satisfaction - nothing works. I haven't used Thunderbird for days-, I still pref
-
Photosmart HP 7520: 10 Windows Error Message update for HP 7520
Daily I get this message. This message started when I got a netbook XP approximately 1-1/2 years he is a. I was hoping that this message would have disappeared when I bought my new laptop running Win 10, but it didn't. I don't even have anymore of th
-
I want to buy Windows 7 are I used Windows 7 in more computer like all the PCs in my office or a single pc I am trying to install 7600.16385.090713 - 1255_x86fre_enterprise_en-us_EVAL_Eval_Enterprise - GRMCENEVAL_EN_DVD.iso are that I can use without
-
What are the files ".hex".
Can someone help me with this problem? Filename = ihp_120.hex I tried to open the file above without success. Windows XP asks for details of the file or the program that was used to create this file. As I have already downloaded this file that I ha